Indesit IWD 61282 C ECO (EU) Užívateľská príručka

Kategória
Práčky
Typ
Užívateľská príručka
GB
1
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Description of the washing machine
and starting a wash cycle, 4-5
Control panel
Indicator lights
Starting a wash cycle
Wash cycles, 6
Table of wash cycles
Personalisation, 7
Setting the temperature
Setting the spin speed
Functions
Detergents and laundry, 8
Detergent dispenser drawer
Preparing the laundry
Garments requiring special care
Load balancing system
Precautions and tips, 9
General safety
Disposal
Care and maintenance, 10
Cutting off the water or electricity supply
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Troubleshooting, 11
Service, 12
IWD 61282
Instructions for use
WASHING MACHINE
English,1
GB
Polski,25
PL
Česky,13
CZ
2
GB
Installation
Levelling the machine correctly will provide it with stability,
help to avoid vibrations and excessive noise and prevent it
from shifting while it is operating. If it is placed on carpet or
a rug, adjust the feet in such a way as to allow a sufficient
ventilation space underneath the washing machine.
Connecting the electricity and water
supplies
Connecting the water inlet hose
1. Connect the supply pipe
by screwing it to a cold
water tap using a ¾ gas
threaded connection (see
figure).
Before performing the con-
nection, allow the water to
run freely until it is perfectly
clear.
2. Connect the inlet hose
to the washing machine by
screwing it onto the corre-
sponding water inlet of the
appliance, which is situa-
ted on the top right-hand
side of the rear part of the
appliance (see figure).
3. Make sure that the hose is not folded over or bent.
! The water pressure at the tap must fall within the values
indicated in the Technical details table (see next page).
! If the inlet hose is not long enough, contact a specialised
shop or an authorised technician.
! Never use second-hand hoses.
! Use the ones supplied with the machine.
! This instruction manual should be kept in a safe place for
future reference. If the washing machine is sold, transferred
or moved, make sure that the instruction manual remains
with the machine so that the new owner is able to familiari-
se himself/herself with its operation and features.
! Read these instructions carefully: they contain vital infor-
mation relating to the safe installation and operation of the
appliance.
Unpacking and levelling
Unpacking
1. Remove the washing machine from its packaging.
2. Make sure that the washing machine has not been
damaged during the transportation process. If it has been
damaged, contact the retailer and do not proceed any
further with the installation process.
3. Remove the 4 protective
screws (used during tran-
sportation) and the rubber
washer with the correspon-
ding spacer, located on the
rear part of the appliance
(see figure).
4. Close off the holes using the plastic plugs provided.
5. Keep all the parts in a safe place: you will need them
again if the washing machine needs to be moved to ano-
ther location.
! Packaging materials should not be used as toys for
children.
Levelling
1. Install the washing machine on a flat sturdy floor, without
resting it up against walls, furniture cabinets or anything
else.
2. If the floor is not perfectly
level, compensate for any
unevenness by tightening
or loosening the adjusta-
ble front feet (see figure);
the angle of inclination,
measured in relation to the
worktop, must not exceed
2°.
GB
3
Technical data
Model
IWD 61282
Dimensions
width 59.5 cm
height 85 cm
depth 53,5 cm
Capacity
from 1 to 6 kg
Electrical
connections
please refer to the technical data plate
fixed to the machine
Water connection
maximum pressure 1 MPa (10 bar)
minimum pressure 0.05 MPa (0.5 bar)
drum capacity 52 litres
Spin speed
up to 1200 rotations per minute
Test wash cycles
in accordance
with directives
1061/2010 and
1015/2010
Programme 2: Cotton Standard 60°;
Programme 3: Cotton Standard 40°.
This appliance conforms to the following
EC Directives:
- 2004/108/EC (Electromagnetic
Compatibility)
- 2002/96/EC
- 2006/95/EC Low Voltage)
65 - 100 cm
Connecting the drain hose
Connect the drain hose,
without bending it, to a drai-
nage duct or a wall drain
located at a height between
65 and 100 cm from the
floor;
alternatively, rest it on
the side of a washbasin
or bathtub, fastening the
duct supplied to the tap
(see figure). The free end
of the hose should not be
underwater.
! We advise against the use of hose extensions; if it is
absolutely necessary, the extension must have the same
diameter as the original hose and must not exceed 150 cm
in length.
Electrical connections
Before plugging the appliance into the electricity socket,
make sure that:
the socket is earthed and complies with all applicable
laws;
the socket is able to withstand the maximum power load
of the appliance as indicated in the Technical data table
(see opposite);
the power supply voltage falls within the values indicated
in the Technical data table (see opposite);
the socket is compatible with the plug of the washing
machine. If this is not the case, replace the socket or the
plug.
! The washing machine must not be installed outdoors,
even in covered areas. It is extremely dangerous to leave
the appliance exposed to rain, storms and other weather
conditions.
! When the washing machine has been installed, the elec-
tricity socket must be within easy reach.
! Do not use extension cords or multiple sockets.
! The cable should not be bent or compressed.
! The power supply cable must only be replaced by autho-
rised technicians.
Warning! The company shall not be held responsible in the
event that these regulations are not respected.
The first wash cycle
Once the appliance has been installed, and before you use
it for the first time, run a wash cycle with detergent and no
laundry, using the wash cycle 2.
4
GB
Detergent dispenser drawer: used to dispense
detergents and washing additives (see “Detergents and
laundry”).
ON/OFF button: switches the washing machine on and
off.
WASH CYCLE knob: used to set the desired wash cycle
(see “Table of wash cycles”).
FUNCTION buttons with indicator light: used to select the
available functions. The indicator light corresponding to the
selected function will remain lit.
TEMPERATURE knob: sets the temperature or the cold
wash cycle (see “Personalisation”).
SPIN SPEED knob: sets the spin speed or exclude the
spin cycle completely (see “Personalisation”).
DISPLAY: used to view the duration of the various cycles
available and the remaining time of a cycle in progress;
if the DELAY TIMER option has been selected, the
countdown to the start of the selected cycle will appear.
DELAY TMER button : press to set a delayed start
time for the selected wash cycle. The delay time will be
shown on the display.
WASH CYCLE PROGRESS
indicator light
s: used to
monitor the progress of the wash cycle.
The illuminated indicator light shows which phase is in
progress.
DOOR LOCKED indicator light: indicates whether the
door may be opened or not (see next page).
START/PAUSE button with indicator light: starts or tem-
porarily interrupts the wash cycles.
N.B. To pause the wash cycle in progress, press this
button; the corresponding indicator light will flash orange,
while the indicator light for the current wash cycle phase
will remain lit in a fixed manner. If the DOOR LOCKED
indicator light is switched off, the door may be opened.
To start the wash cycle from the point at which it was inter-
rupted, press this button again.
Standby mode
This washing machine, in compliance with new energy sa-
ving regulations, is fitted with an automatic standby system
which is enabled after about 30 minutes if no activity is
detected. Press the ON-OFF button briefly and wait for the
machine to start up again.
Consumption in off-mode: 0,5 W
Consumption in Left-on: 0,5 W
Description of the washing
machine and starting a wash cycle
WASH CYCLE
PROGRESS
DOOR LOCKED
indicator light
START/
PAUSE
button with
indicator light
Control panel
Detergent dispenser drawer
ON/OFF
button
WASH CYCLE
knob
TEMPERATURE
knob
FUNCTION
buttons with
indicator lights
SPIN SPEED
knob
DISPLAY
DELAY TIMER
button
GB
5
Indicator lights
The indicator lights provide important information.
This is what they can tell you:
Wash cycle phase indicator lights
Once the desired wash cycle has been selected and has
begun, the indicator lights switch on one by one to indicate
which phase of the cycle is currently in progress.
Function buttons and corresponding indicator
lights
When a function is selected, the corresponding indicator
light will illuminate.
If the selected function is not compatible with the program-
med wash cycle, the corresponding indicator light will flash
and the function will not be activated.
If the selected function is not compatible with another
function which has been selected previously, the indicator
light corresponding to the first function selected will
flash and only the second function will be activated; the
indicator light corresponding to the enabled option will
remain lit.
Door locked indicator light
When the indicator light is on, the porthole door is locked
to prevent it from being opened; make sure the indicator
light is off before opening the door (wait approximately 3
minutes). To open the door during a running wash cycle,
press the START/PAUSE button; the door may be opened
once the DOOR LOCKED indicator light turns off.
Starting a wash cycle
1. Switch the washing machine on by pressing the ON/OFF button. All indicator lights will switch on for a few seconds, then
they will switch off and the START/PAUSE indicator light will pulse.
2. Load the laundry and close the door.
3. Set the WASH CYCLE knob to the desired programme.
4. Set the washing temperature (see “Personalisation”).
5. Set the spin speed (see “Personalisation”).
6. Measure out the detergent and washing additives (see “Detergents and laundry”).
7. Select the desired functions.
8. Start the wash cycle by pressing the START/PAUSE button and the corresponding indicator light will remain lit in a fixed
manner, in green.
To cancel the set wash cycle, pause the machine by pressing the START/PAUSE button and select a new cycle.
9. At the end of the wash cycle the indicator light will switch on. The door can be opened once the DOOR LOCK indi-
cator light turns off. Take out your laundry and leave the appliance door ajar to make sure the drum dries completely. Switch
the washing machine off by pressing the ON/OFF button.
Wash
Rinse
Spin
Drain
End of wash cycle
6
GB
Wash cycles
Table of wash cycles
Outwear (wash cycle 9): is studied for washing water-repellent fabrics and winter jackets (e.g. Gore-Tex, polyester, nylon); for
best results, use a liquid detergent and dosage suitable for a half-load; pre-treat necks, cuffs and stains if necessary; do not
use softeners or detergents containing softeners. Stuffed duvets cannot be washed with this programme.
Sport Intensive (wash cycle 12) is for washing heavily soiled sports clothing fabrics (tracksuits, shorts, etc.); for best re-
sults, we recommend not exceeding the maximum load indicated in the “Table of wash cycles”.
Sport Light (wash cycle 13) is for washing lightly soiled sports clothing fabrics (tracksuits, shorts, etc.); for best results, we
recommend not exceeding the maximum load indicated in the “Table of wash cycles”. We recommend using a liquid deter-
gent and dosage suitable for a half-load.
Special Shoes (wash cycle 14) is for washing sports shoes; for best results, do not wash more than 2 pairs simultaneously.
The 20° wash cycles (20° Zone) offer effective washing performance at low temperatures, reducing electricity usage and
expenditure while benefitting the environment.The 20° wash cycles meet all requirements:
Cotton Standard 20° (programme 6) ideal for heavily soiled cotton loads. The effective performance levels achieved at
cold temperatures, which are comparable to washing at 40°, are guaranteed by a mechanical action which operates at
varying speed, with repeated and frequent peaks.
Mix Light (programme 7) ideal for mixed loads (cotton and synthetics) with a normal soil level. The effective performance
levels achieved at cold temperatures are guaranteed by a mechanical action which operates at varying speed, across set
average intervals.
20’ Refresh (programme 8) ideal for refreshing and washing lightly soiled garments in a few minutes. It lasts just 20 minutes
and therefore saves both time and energy. It can be used to wash different types of fabrics together (except for wool and
silk), with a maximum load of 1.5 kg.
1) Test wash cycle in compliance with directive 1061/2010: set wash cycle 2 with a temperature of 60°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments
which can be washed at 60°C. The actual washing temperature may differ from the indicated value.
2) Test wash cycle in compliance with directive 1061/2010: set wash cycle 3 with a temperature of 40°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments
which can be washed at 40°C. The actual washing temperature may differ from the indicated value.
For all Test Institutes:
2) Long wash cycle for cottons: set wash cycle 3 with a temperature of 40°C.
3) Long wash cycle for synthetics: set wash cycle 4; with a temperature of 40°C.
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary accor-
ding to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.
Wash cycles
Description of the wash cycle
Max.
temp.
(°C)
Max.
speed
(rpm)
Detergents
Max.
load (kg)
Residual
dampness %
Energy
consumption
kWh
Total water lt
Cycle
duration
Wash
Fabric
softener
Daily
1
White Cotton: extremely soiled whites.
90° 1200
6 53 2,10 70 125’
2
Cotton Standard 60° (1): heavily soiled whites and resistant colours.
60° 1200
6 53 0,87 51 150’
3
Cotton Standard 40° (2): lightly soiled whites and delicate colours.
40° 1200
6 53 0,86 69 145’
4
Synthetics: heavily soiled resistant colours.
50° 800
3 - - - 105’
4
Synthetics (3): lightly soiled resistant colours.
40° 800
3 44 0,57 46 95’
5
Mix Colored: lightly soiled whites and delicate colours.
40° 1200
6 53 0,60 50 85’
20° Zone
6
Cotton Standard 20°: lightly soiled whites and delicate colours.
20° 1200
6 - - - 170’
7 Mix Light
20° 800
6 - - - 120’
8 20’ Refresh
20° 800
1,5 - - - 20’
Special
9 Outwear
30° 400
-
2 - - - 60’
10
Wool: for wool, cashmere, etc.
40° 800
1,5 - - - 70’
11 Jeans
40° 800
3,5 - - - 70’
Sport
12 Sport Intensive
30° 600
2,5 - - - 85’
13 Sport Light
30° 600
2,5 - - - 60’
14 Special Shoes
30° 600
Max.
2 pairs
- - - 60’
Partial wash cycles
Rinse
- 1200
-
6 - - - 36’
Spin + Drain
- 1200
- -
6 - - - 16’
GB
7
Personalisation
Setting the temperature
Turn the TEMPERATURE knob to set the wash temperature (see Table of wash cycles).
The temperature may be lowered, or even set to a cold wash .
The washing machine will automatically prevent you from selecting a temperature which is higher than the maximum value
set for each wash cycle.
Setting the spin speed
Turn the SPIN SPEED knob to set the spin speed for the selected wash cycle.
The maximum spin speeds available for each wash cycle are as follows:
Wash cycles Maximum spin speed
Cottons 1200 rpm
Synthetics 800 rpm
Wool 800 rpm
The spin speed may be lowered, or the spin cycle can be excluded altogether by selecting the symbol .
The washing machine will automatically prevent you from selecting a spin speed which is higher than the maximum speed
set for each wash cycle.
Functions
The various wash functions available with this washing machine will help to achieve the desired results, every time.
To activate the functions:
1. Press the button corresponding to the desired function;
2. the function is enabled when the corresponding indicator light is illuminated.
Note: If the indicator light flashes rapidly, this signals that this particular function may not be selected in conjunction with the
selected wash cycle.
Delay timer
To set a delayed start for the selected programme, press the corresponding button repeatedly until the required delay period
has been reached. When this option is enabled, the symbol lights up on the display. To remove the delayed start option
press the button until the text “OFF” appears on the display.
! This option is enabled with all programmes.
Selecting this option enables you to suitably adjust drum rotation, temperature and water to a reduced load of lightly soiled
cotton and synthetic fabrics (refer to the
“Table of wash cycles”
). “ ” enables you to wash in less time thereby saving
water and electricity. We suggest using a liquid detergent suitably measured out to the load quantity.
! This function may not be used in conjunction with wash cycles 1, 6, 7, 8, 9, 10, 11, 12, 13, 14, , .
The function saves energy by not heating the water used to wash your laundry - an advantage both to the
environment and to your energy bill. Instead, intensified wash action and water optimisation ensure great wash results in the
same average time of a standard cycle.
For the best washing results we recommend the usage of a liquid detergent.
! This function may not be used in conjunction with wash cycles 6, 7, 8, 10, 12, 13, 14, , .
8
GB
Detergents and laundry
Detergent dispenser drawer
Good washing results also depend on the correct dose of
detergent: adding too much detergent will not necessa-
rily result in a more efficient wash, and may in fact cause
build up on the inside of your appliance and contribute to
environmental pollution.
! Do not use hand washing detergents because these
create too much foam.
! Use powder detergent for white cotton garments, for pre-
washing, and for washing at temperatures over 60°C.
! Follow the instructions given on the detergent packaging.
Open the detergent di-
spenser drawer and pour
in the detergent or washing
additive, as follows.
compartment 1: Do not pour detergent into this
compartment
compartment 2: Detergent for the wash cycle
(powder or liquid)
Liquid detergent should only be poured in immediately
prior to the start of the wash cycle.
compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow the grid.
Preparing the laundry
• Divide the laundry according to:
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from whites.
• Empty all garment pockets and check the buttons.
Do not exceed the values listed in the “Table of wash
cycles”, which refer to the weight of the laundry when
dry.
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1200 g
1 towel 150-250 g
1
2
3
Garments requiring special care
Wool: all wool garments can be washed using programme
10, even those carrying the “hand-wash only” label.
For best results, use special detergents and do not exceed
1,5 kg of laundry.
Jeans: Turn garments inside-out before washing and use a
liquid detergent. Use programme 11.
Load balancing system
Before every spin cycle, to avoid excessive vibrations and
to distribute the load in a uniform manner, the drum rotates
continuously at a speed which is slightly greater than the
washing rotation speed. If, after several attempts, the load
is not balanced correctly, the machine spins at a reduced
spin speed. If the load is excessively unbalanced, the
washing machine performs the distribution process instead
of spinning. To encourage improved load distribution and
balance, we recommend small and large garments are
mixed in the load.
GB
9
Precautions and tips
! This washing machine was designed and constructed in
accordance with international safety regulations. The fol-
lowing information is provided for safety reasons and must
therefore be read carefully.
General safety
This appliance is not intended for use by persons (inclu-
ding children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concer-
ning use of the appliance by a person responsible for
their safety. Children should be supervised to ensure that
they do not play with the appliance.
This appliance was designed for domestic use only.
Do not touch the machine when barefoot or with wet or
damp hands or feet.
Do not pull on the power supply cable when unplugging
the appliance from the electricity socket. Hold the plug
and pull.
Do not open the detergent dispenser drawer while the
machine is in operation.
Do not touch the drained water as it may reach extreme-
ly high temperatures.
Never force the porthole door. This could damage the
safety lock mechanism designed to prevent accidental
opening.
If the appliance breaks down, do not under any circum-
stances access the internal mechanisms in an attempt
to repair it yourself.
Always keep children well away from the appliance while
it is operating.
The door can become quite hot during the wash cycle.
If the appliance has to be moved, work in a group of two
or three people and handle it with the utmost care. Never
try to do this alone, because the appliance is very heavy.
Before loading laundry into the washing machine, make
sure the drum is empty.
Disposal
Disposing of the packaging materials: observe local
regulations so that the packaging may be re-used.
The European Directive 2002/96/EC on Waste
Electrical and Electronic Equipment, requires that
old household electrical appliances must not be
disposed of in the normal unsorted municipal waste
stream. Old appliances must be collected separately
in order to optimise the recovery and recycling of the
materials they contain and reduce the impact on human
health and the environment. The crossed out “wheeled
bin” symbol on the product reminds you of your obliga-
tion, that when you dispose of the appliance it must be
separately collected.
Consumers should contact their local authority or
retailer for information concerning the correct
disposal of their old appliance.
10
GB
Care and maintenance
Cutting off the water and electricity
supplies
Turn off the water tap after every wash cycle. This will
limit wear on the hydraulic system inside the washing
machine and help to prevent leaks.
Unplug the washing machine when cleaning it and du-
ring all maintenance work.
Cleaning the washing machine
The outer parts and rubber components of the appliance
can be cleaned using a soft cloth soaked in lukewarm
soapy water. Do not use solvents or abrasives.
Cleaning the detergent dispenser drawer
Remove the dispenser by
raising it and pulling it out
(see figure).
Wash it under running wa-
ter; this operation should be
repeated frequently.
Caring for the door and drum of your
appliance
Always leave the porthole door ajar in order to prevent
unpleasant odours from forming.
Cleaning the pump
The washing machine is fitted with a self-cleaning pump
which does not require any maintenance. Sometimes, small
items (such as coins or buttons) may fall into the pre-cham-
ber which protects the pump, situated in its bottom part.
! Make sure the wash cycle has finished and unplug the
appliance.
To access the pre-chamber:
1. using a screwdriver,
remove the cover panel
on the lower front part of
the washing machine (see
figure);
2. unscrew the lid by rota-
ting it anti-clockwise (see
figure): a little water may
trickle out. This is perfectly
normal;
3. clean the inside thoroughly;
4. screw the lid back on;
5. reposition the panel, making sure the hooks are securely
in place before you push it onto the appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If there are any
cracks, it should be replaced immediately: during the wash
cycles, water pressure is very strong and a cracked hose
could easily split open.
! Never use second-hand hoses.
GB
11
Troubleshooting
Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure
that the problem cannot be solved easily using the following list.
Problem:
The washing machine does not
switch on.
The wash cycle does not start.
The washing machine does not
take in water (“H2O” will flash on
the display).
The washing machine continuously
takes in and drains water.
The washing machine does not
drain or spin.
The washing machine vibrates a lot
during the spin cycle.
The washing machine leaks.
Thefunction indicator lights and
thestart/pauseindicator light flash,
while one of thephase in progress
indicator lights and the door locked
indicator light will remain lit in a fixed
manner.
There is too much foam.
Possible causes / Solutions:
The appliance is not plugged into the socket fully, or is not making contact.
There is no power in the house.
The washing machine door is not closed properly.
The ON/OFF button has not been pressed.
The START/PAUSE button has not been pressed.
The water tap has not been opened.
A delayed start has been set (see “Personalisation”).
The water inlet hose is not connected to the tap.
The hose is bent.
The water tap has not been opened.
There is no water supply in the house.
The pressure is too low.
The START/PAUSE button has not been pressed.
The drain hose is not fitted at a height between 65 and 100 cm from the floor
(see “Installation”).
The free end of the hose is under water (see “Installation”).
The wall drainage system is not fitted with a breather pipe.
If the problem persists even after these checks, turn off the water tap, switch
the appliance off and contact the Assistance Service. If the dwelling is on one of
the upper floors of a building, there may be problems relating to water drainage,
causing the washing machine to fill with water and drain continuously. Special
anti-draining valves are available in shops and help to avoid this inconvenience.
The wash cycle does not include draining: some wash cycles require the drain
phase to be started manually.
The drain hose is bent (see “Installation”).
The drainage duct is clogged.
The drum was not unlocked correctly during installation (see “Installation”).
The washing machine is not level (see “Installation”).
The washing machine is trapped between cabinets and walls (see “Installation”).
The water inlet hose is not screwed on properly (see “Installation”).
The detergent dispenser drawer is blocked (for cleaning instructions, see “Care
and maintenance”).
The drain hose is not fixed properly (see “Installation”).
Switch off the machine and unplug it, wait for approximately 1 minute and then
switch it back on again.
If the problem persists, contact the Technical Assistance Service.
The detergent is not suitable for machine washing (it should display the text
“for washing machines” or “hand and machine wash”, or the like).
Too much detergent was used.
12
GB
Service
Before calling for Assistance:
Check whether you can solve the problem alone (see “Troubleshooting”);
Restart the programme to check whether the problem has been solved;
If this is not the case, contact an authorised Technical Assistance Centre using the telephone number provided on the
guarantee certificate.
! Always request the assistance of authorised technicians.
Have the following information to hand:
the type of problem;
the appliance model (Mod.);
the serial number (S/N).
This information can be found on the data plate applied to the rear of the washing machine, and can also be found on the
front of the appliance by opening the door.
CZ
13
Česky
Obsah
Instalace, 14-15
Rozbalení a vyrovnání do vodorovné polohy
Připojení k elektrické a k vodovodní síti
První prací cyklus
Technické údaje
Popis pračky a zahájení pracího
programu, 16-17
Ovládací panel
Kontrolky
Zahájení pracího programu
Prací programy, 18
Tabulka pracích programů
Uživatelská nastavení, 19
Nastavení teploty
Nastavení rychlosti odstřeďování
Funkce
Prací prostředky a prádlo, 20
Dávkovač pracích prostředků
Příprava prádla
Oděvy vyžadující zvláštní péči
Systém automatického vyvážení náplně
Opatření a rady, 21
Základní bezpečnostní pokyny
Likvidace
Údržba a péče, 22
Uzavření přívodu vody a vypnutí elektrického napájení
Čištění pračky
Čištění dávkovače pracích prostředků
Péče o dvířka a buben
Čištění čerpadla
Kontrola přítokové hadice na vodu
Poruchy a způsob jejich odstranění, 23
Servisní služba, 24
CZ
IWD 61282
Návod k použití
PRAČKA
14
CZ
! Je důležité uschovat tento návod tak, abyste jej mohli
kdykoli konzultovat. V případě prodeje, darování nebo
přestěhování pračky se ujistěte, že zůstane uložen
v blízkosti pračky, aby mohl posloužit novému majiteli při
seznámení s její činností a s příslušnými upozorněními.
! Pozorně si přečtěte uvedené pokyny: obsahují důležité
informace týkající se instalace, použití a bezpečnosti při
práci.
Rozbalení a vyrovnání do vodorovné po-
lohy
Rozbalení
1. Rozbalte pračku.
2. Zkontrolujte, zda během přepravy nedošlo k jejímu
poškození. V případě, že je poškozena, ji nezapojujte a
obraťte se na prodejce.
3. Odstraňte 4 šrouby
chránící před poškozením
během přepravy a gumo-
vou podložku s příslušnou
rozpěrkou, které se
nacházejí v zadní části (viz
obrázek).
4. Uzavřete otvory po šroubech plastovými krytkami z
příslušenství.
5. Uschovejte všechny díly: v případě opětovné přepravy
pračky je bude třeba namontovat zpět.
! Obaly nejsou hračky pro děti!
Vyrovnání do vodorovné polohy
1. Pračku je třeba umístit na rovnou a pevnou podlahu,
aniž by se opírala o stěnu, nábytek či něco jiného.
2. V případě, že podlaha
není dokonale vodoro-
vná, mohou být případné
rozdíly vykompenzovány
šroubováním předních
nožek (viz obrázek); Úhel
sklonu, naměřený na
pracovní ploše, nesmí
přesáhnout 2°.
Dokonalé vyrovnání do vodorovné polohy zabezpečí
stabilitu zařízení a zamezí vzniku vibrací a hluku během
činnosti. V případě instalace na podlahovou krytinu nebo
na koberec nastavte nožky tak, aby pod pračkou zůstal
dostatečný volný prostor pro ventilaci.
Připojení k elektrické a k vodovodní síti
Připojení přítokové hadice vody
1. Připojte přívodní hadici
jejím zašroubováním ke
kohoutku studené vody
s hrdlem se závitem 3/4“
(viz obrázek).
Před připojením hadice
nechte vodu odtékat, do-
kud nebude čirá.
2. Připojte přítokovou hadi-
ci k pračce prostřednictvím
příslušné přípojky na vodu,
umístěné vpravo nahoře
(viz obrázek).
3. Dbejte na to, aby hadice nebyla příliš ohnutá ani
stlačená.
! Tlak v rozvodu vody se musí pohybovat v rozmezí hod-
not uvedených v tabulce s technickými údaji
(viz vedlejší strana).
! V případě, že délka přítokové hadice nebude
dostatečná, obraťte se na specializovanou prodejnu
nebo na autorizovaný technický personál.
! Nikdy nepoužívejte již použité hadice.
! Používejte hadice z příslušenství zařízení.
Instalace
CZ
15
65 - 100 cm
Připojení vypouštěcí hadice
Připojte vypouštěcí hadi-
ci, aniž byste ji ohýbali,
k odpadovému potrubí
nebo k odpadu ve stěně,
který se nachází od 65 do
100 cm nad zemí;
nebo ji uchyťte k okra-
ji umývadla či vany a
připevněte vodicí držák
z příslušenství ke kohoutu
(viz obrázek). Volný konec
vypouštěcí hadice nesmí
zůstat ponořený do vody.
! Použití prodlužovacích hadic se nedoporučuje; je-li
však nezbytné, prodlužovací hadice musí mít stejný
průměr jako originální hadice a její délka nesmí
přesáhnout 150 cm.
Připojení k elektrické síti
Před zasunutím zástrčky do zásuvky se ujistěte, že:
• Je zásuvka uzemněna a že vyhovuje normám;
• je zásuvka schopna snést maximální zátěž odpovída-
jící jmenovitému příkonu zařízení, uvedenému v tabul-
ce s technickými údaji
(viz vedle);
• hodnota napájecího napětí odpovídá údajům uve-
deným v tabulce s technickými údaji
(viz vedle);
• je zásuvka kompatibilní se zástrčkou pračky.
V opačném případě je třeba vyměnit zásuvku nebo
zástrčku.
! Pračka nesmí být umístěna venku – pod širým nebem,
a to ani v případě, že by se jednalo o místo chráněné
před nepřízní počasí, protože je velmi nebezpečné vysta-
vit ji působení deště a bouří.
! Po denitivní instalaci pračky musí zásuvka zůstat
snadno přístupná.
! Nepoužívejte prodlužovací kabely a rozvodky.
! Kabel nesmí být ohnutý ani stlačený.
! Výměna kabelu musí být svěřena výhradně autorizo-
vanému technickému personálu.
Upozornění! Výrobce neponese žádnou odpovědnost za
následky nerespektování uvedených předpisů.
První prací cyklus
Po instalaci zařízení je třeba ještě předtím, než je
použijete na praní prádla, provést jeden zkušební cyklus
s pracím prostředkem a bez náplně prádla nastavením
pracího programu 2.
Technické údaje
Model IWD 61282
Rozměry
šířka 59,5 cm
výška 85 cm
hloubka 53,5 cm
Kapacita od 1 do 6 kg
Napájení
Viz štítek s technickými údaji, aplikovaný
na zařízení.
Připojení k
rozvodu vody
maximální tlak 1 MPa (10 bar)
minimální tlak 0.05 MPa (0.5 bar)
kapacita bubnu 52 litrů
Rychlost
odstřeďování
až do 1200 otáček za minutu
Kontrolní programy
podle směrnic
1061/2010 a
1015/2010
program 2; standardní program pro bavl-
nu pro praní při 60°C.
program 3; standardní program pro bavl-
nu pro praní při 40°C.
Toto zařízení odpovídá následujícím
normám Evropské unie:
- 2004/108/CE (Elektromagnetická kom-
patibilita)
- 2006/95/CE (Nízké napětí)
- 2002/96/CE
Hlučnost
(dB(A) re 1 pW)
Praní: 54
Odstřeďování: 80
16
CZ
Dávkovač pracích prostředků: slouží k dávkování
pracích prostředků a přídavných prostředků (viz „Prací
prostředky a prádlo“).
Tlačítko ON/OFF: slouží k zapnutí a vypnutí pračky.
Otočný ovladač PROGRAMŮ: pro nastavení pracích
programů. Během pracího programu zůstane ve stejné
poloze.
FUNKČNÍ tlačítka s kontrolkami: slouží k volbě jed-
notlivých dostupných funkcí. Kontrolka zvolené funkce
zůstane rozsvícena.
Otočný ovladač ODSTŘEĎOVÁNÍ: slouží k nastavení
odstřeďování nebo k jeho vyloučení (viz „Uživatelská
nastavení“).
Ot ovladač TEPLOTY: slouží k nastavení teploty
praní nebo praní ve studené vodě (viz „Uživatelská
nastavení“).
DISPLEJ: slouží k zobrazení doby trvání různých
programů, které jsou k dispozici, a po zahájení cyklu
i zbývající doby ukončení probíhajícího programu;
v případě nastavení ODLOŽENÝ START bude zobraze-
na doba chybějící do zahájení zvoleného programu.
ODLOŽENÝ START : stiskněte za účelem nastavení
odloženého startu zvoleného programu. Doba, o kterou
bude start odložen, bude zobrazena na displeji.
Kontrolky
PRŮBĚHU PRACÍHO CYKLU: slouží ke kon-
trole průběhu pracího programu.
Rozsvícená
kontrolka
poukazuje na probíhající fázi.
Kontrolka ZABLOKOVANÁ DVÍŘKA: informuje o tom,
zda je možné otevřít dvířka (viz vedlejší strana).
Tlačítko s kontrolkou  Slouží ke spuštění
nebo dočasnému přerušení programů.
POZN.: Stisknutí tohoto tlačítka slouží k přerušení
probíhajícího praní; příslušná kontrolka bude blikat
oranžovým světlem, zatímco kontrolka probíhající fáze
zůstane rozsvícena stálým světlem. Když bude kontrol-
ka ZABLOKOVANÁ DVÍŘKA zhasnuta, bude možné
otevřít dvířka.
Za účelem opětovného zahájení praní z bodu, ve kterém
bylo přerušeno, znovu stiskněte toto tlačítko.
Pohotovostní režim
Za účelem shody s novými předpisy souvisejícími s
energetickou úsporou je tato pračka vybavena systémem
automatického vypnutí (přechodu do pohotovostního
režimu – standby), který je aktivován po uplynutí 30 mi-
nut, když se pračka nepoužívá. Krátce stiskněte tlačítko
ON/OFF a vyčkejte na obnovení činnosti zařízení.
Spotřeba v off-mode: 0,5 W
Spotřeba v Left-on: 0,5 W
Popis pračky a zahájení
pracího programu
Ovládací panel
Kontrolky
PRŮBĚHU
PRACÍHO
CYKLU
Kontrolka
ZABLOKOVANÁ
DVÍŘKA
Tlačítko s
kontrolkou
START/
PAUSE
Dávkovač pracích prostředků
Tlačítko
ON/OFF
Otočný ovlad
PROGRAMŮ
Otočný ovladač
TEPLOTY
Otočný ovladač
ODSTŘEĎOVÁNÍ
FUNKČNÍ
tlačítka
s kontrolkami
DISPLEJ
ODLOŽE
START
CZ
17
Kontrolky
Kontrolky jsou zdrojem důležitých informací.
Informují nás o následujících skutečnostech:
Kontrolka aktuální fáze pracího programu:
Po zvolení a zahájení požadovaného pracího cyklu dojde
k postupnému rozsvícení kontrolek informujících o jeho
průběhu.
Funkční tlačítka a příslušné kontrolky
Po zvolení konkrét funkce dojde k rozscení příslušné
kontrolky.
V případě, že zvolená funkce není kompatibilní s nasta-
veným pracím programem, příslušná kontrolka začne
blikat a funkce nebude aktivována.
V případě, že zvolená funkce není kompatibilní s jinou
předem zvolenou funkcí, kontrolka první funkce bude
blikat a bude aktivována pouze druhá, přičemž kontrolka
zvolené funkce se rozsvítí stálým světlem.
Kontrolka zablokovaných dvířek
Rozsvíce této kontrolky poukazuje na to, že dvířka jsou
zajna kvůli zamezení náhodmu otevře; aby se zab-
nilo poškození dřek, ed jejich otevřem je eba vkat,
dokud uvedená kontrolka nezhasne; (vyčkejte ibliž 3 mi-
nuty). Za účelem otevření dvířek v průběhu pracího cyklu
stiskněte tlačítko START/PAUSE; když bude kontrolka
ZABLOKOVANÁ DVÍŘKA zhasnutá, bude možné otevřít
dvířka.
Zahájení pracího programu
1. Zapněte pračku stisknutím tlačítka ON/OFF. Všechny kontrolky se rozsvítí na několik sekund, poté se zhasnou a bude
blikat kontrolka START/PAUSE.
2. Naplňte pračku a zavřete dvířka.
3. Otočným ovladačem PROGRAMŮ nastavte požadovaný prací program.
4. Nastavte teplotu praní (viz „Uživatelská nastavení“).
5. Nastavte rychlost odstřeďování (viz „Uživatelská nastavení“).
6. Nadávkujte prací prostředek a přídavné prostředky (viz „Prací prostředky a prádlo“).
7. Zvolte požadované funkce.
8. Zahajte prací program stisknutím tlačítka START/PAUSE a příslušná kontrolka zůstane rozsvícena stálým světlem ze-
lené barvy. Zrušení nastaveného pracího cyklu se provádí přerušením činnosti zařízení stisknutím tlačítka START/PATA a
volbou nového cyklu.
9. Po ukončení pracího programu se rozsvítí kontrolka . Po zhasnutí kontrolky ZABLOKOVA DŘKA bude
možné otevřít dvířka. Vytáhněte prádlo a nechte dvířka pootevřená, aby bylo umožněno vysušení bubnu. Vypněte pračku
stisknutím tlačítka ON/OFF.
Praní
Máchání
Odstřeďování
Odčerpání vody
Ukončení praní
18
CZ
Prací programy
Tabulka pracích programů
Outwear (program 9) byl navržen pro praní hydrofobních látek a větrovek (např. z goretexu, polyesteru, nylonu); pro dosažení
optimálních výsledků použijte tekutý prací prostředek a dávku vhodnou pro poloviční náplň; předběžně ošetřete manžety, límce
a skvrny; nepoužívejte aviváž ani prací prostředky s aviváží. S použitím tohoto programu nelze prát péřové větrovky.
Sport Intensive (program 12) byl navržen pro velmi znečištěné látky sportovního oblečení (teplákové soupravy, šortky apod.);
pro dosažení optimálních výsledků se doporučuje nepřekračovat maximální náplň uvedenou v “Tabulka pracích programů”.
Sport Light (program 13) byl navržen pro mírně znečištěné látky sportovního oblečení (teplákové soupravy, šortky apod.);
pro dosažení optimálních výsledků se doporučuje nepřekračovat maximální náplň uvedenou v “Tabulka pracích programů”.
Doporučuje se použít tekutý prací prostředek a použít dávku vhodnou pro poloviční náplň.
Sport Shoes (program 14) byl navržen pro praní sportovní obuvi; pro dosažení optimálních výsledků neperte více než
2 páry najednou.
Programy 20° (20° Zone) nabízejí dobrou výkonnost praní při nízkých teplotách, přičemž umožňují nižší použití elektrické
energie s výhodami pro nanční úsporu i pro životní prostředí. Programy 20° vyhovují všem požadavkům:
Standardní program pro bavlnu pro praní při 20°C (program 6) ideální pro náplně ze znečištěné bavlny. Dobrá výkonnost
i za studena, srovnatelná s praním při 40 °C, je zaručena mechanickým působením, které je založeno na změně rychlosti v
krátkých nebo dlouhých intervalech.
Mix Light (program 7)idlní pro smíšené pl(bavlna a syntetika), tvené sed znečištěným pdlem. Dob výkonnost pra i
za studena je zarena mechanicm sobem, které je zaleno na z rychlosti ve sedch nebo určech intervalech.
20’ Refresh (program 8) osvěžení ideální cyklus pro osvěžení a praní mírně znečištěného prádla v průběhu pár minut. Trvá
pouze 20 minut a šetří tak čas i energii. Umožňuje prát dohromady tkaniny různého druhu (s výjimkou vlny a hedvábí) při náplni
nepřesahující 1,5 kg.
Doba trvání cyklu uvedená na displeji nebo v návodu představuje odhad vypočítaný na základě standardních podmínek. Skutečná doba se může měnit v závislosti na četných faktorech, jako je
např. teplota a tlak vody na vstupu, teplota prostředí, množství pracího prostředku, množství a druh náplně, vyvážení náplně a zvolené volitelné funkce.
1) Kontrolní program podle normy 1061/2010: nastavte program 2 s teplotou 60°C.
Tento cyklus je vhodný pro praní běžně znečištěné bavlny a jedná se o nejúčinnější cyklus z hlediska kombinované spotřeby energie a vody určený pro prádlo, které
lze prát při teplotě do 60 °C. Skutečná teplota praní se může lišit od uvedené.
2) Kontrolní program podle normy 1061/2010: nastavte program 3 s teplotou 40°C.
Tento cyklus je vhodný pro praní běžně znečištěné bavlny a jedná se o nejúčinnější cyklus z hlediska kombinované spotřeby energie a vody určený pro prádlo, které
lze prát při teplotě do 40°C. Skutečná teplota praní se může lišit od uvedené.
Pro všechny Kontrolní ústavy:
2) Dlouhý program na praní bavlny: nastavte program 3 s teplotou 40°C.
3) Syntetický program spolu: nastavte program 4 s teplotou 40°C.
Programy
Popis programu
Max.
teplota
C)
Max. rychlost
(oèky za minutu)
Prací
pro-
støedky
Max.plò (kg)
Zbytková
vlhkost %
Spotøeba
energie kWh
Celkové
mnoství vody lt
Cycle duration
Praní
Aviváz
Programy pro kazdodenpraní (Daily)
1
Bavlna: mimoøád zništìné bílé prádlo.
90° 1200
6 53 2,10 70 125’
2
Standardní program pro bavlnu pro praní při 60°C (1): silnì zneèištìné bílé a barevné
prádlo z odolných tkanin.
60° 1200
6 53 0,87 51 150’
3
Standardní program pro bavlnu pro praní při 40°C (2): silnì zneèištìné bílé a barevné
choulostivé prádlo.
40° 1200
6 53 0,86 69 145’
4
Syntetika: velmi zneètìné barev prádlo z odolch tkanin.
50° 800
3 - - - 105’
4
Syntetika (3): èásteèné zneèištìné barev prádlo z odolch tkanin.
40° 800
3 44 0,57 46 95
5
Barevná bavlna: málo zneèiš a barev choulostivé pdlo.
40° 1200
6 53 0,60 50 85
20° Zone
6
Standardní program pro bavlnu pro praní při 20°C: silnì zneèištìné bílé a barevné chou-
lostivé prádlo.
20° 1200
6 - - - 170’
7
Mix Light
20° 800
6 - - - 120’
8
20’ Refresh
20° 800
1,5 - - - 20
Speciál programy (Special)
9
Outwear
30° 400
-
2 - - - 60’
10
Vlna: pro vlnu, kr atd.
40° 800
1,5 - - - 70
11
Jeans
40° 800
3,5 - - - 70
Sport
12
Sport Intensive
30° 600
2,5 - - - 85’
13
Sport Light
30° 600
2,5 - - - 60’
14
Sport Shoes
30° 600
Max.
2 ry.
- - - 60’
í programy
chání
- 1200
-
6 - - - 36’
Odstøeïování + Oerpání vody
- 1200
- -
6 - - - 16’
CZ
19
Nastavení teploty
Otáčením otočného ovladače TEPLOTY se nastavuje teplota praní (viz Tabulka programů).
Teplota může být postupně snižována až po praní ve studené vodě ( ).
Zařízení automaticky zabrání nastavení vyšší teploty, než je maximální teplota pro každý prací program.
Nastavení odstřeďování
Otáčením otočného ovladače ODSTŘEĎOVÁNÍ se nastavuje rychlost odstřeďování zvoleného pracího programu.
Maximální rychlosti pro jednotlivé prací programy jsou:
 Maximální rychlost
Bavlna 1200 otáček za minutu
Syntetika 800 otáček za minutu
Vlna 800 otáček za minutu
Rychlost odstřeďování může být snížena nebo může být odstřeďování vyloučeno volbou symbolu .
Zařízení automaticky zabrání odstřeďování vyšší rychlostí, než je maximální rychlost pro každý prací program.
Funkce
Jednotlivé funkce, kterými pračka disponuje, umožňují dosáhnout požadovaného stupně čistoty a bělosti praného prádla.
Způsob aktivace jednotlivých funkcí:
1. stiskněte příslušné tlačítko požadované funkce;
2. rozsvícení příslušné kontrolky signalizuje, že došlo k aktivaci zvolené funkce.
Poznámka: Rychlé blikání kontrolky poukazuje na to, že příslušná funkce je nepoužitelná během nastaveného pracího
programu.
Odložený start
Pro nastavení odloženého startu zvoleného programu stiskněte příslušné tlačítko do dosažení požadované doby odložení.
Po zvolení této volitelné funkce se zobrazí symbol. Zrušení odloženého startu se provádí stisknutím tlačítka do zobrazení
nápisu OFF.
! Je aktivní u všech pracích programů.
Volbou této volitelné funkce se bude mechanický pohon, teplota a voda optimalizovat pro sníženou náplň mírně
znečistěné bavlny a syntetických materiálů “Tabulka pracích programů”. Při použití “ ” můžete pracovat s kratšími
dobami a ušetřit vodu a energii. Doporučuje se používat dávku tekutého pracího prostředku vhodnou pro naplněné
množství.
! Tato funkce není použitelná u programů 1, 6, 7, 8, 9, 10, 11, 12, 13, 14, , .
Funkce přispívá k energetické úspoře tím, že neohřívá vodu použitou pro praní prádla – jedná se o výhodu
pro životní prostředí i pro účet za elektrickou energii. Zesílený účinek a optimalizovaná spotřeba vody vskutku zaručují
optimální výsledky během stejné průměrné doby odpovídající standardnímu cyklu. Pro dosažení lepších výsledků praní
se doporučuje použít tekutý prací prostředek.
! Tato funkce není použitelná u programů 6, 7, 8, 10, 12, 13, 14, , .
Uživatelská nastavení
20
CZ
Prací prostředky a prádlo
Dávkovač pracích prostředků
Dobrý výsledek praní závisí také na správném dávkování
pracího prostředku: použití jeho nadměrného množství
snižuje efektivitu praní a napomáhá tvorbě vodního
kamene na vnitřních částech pračky a zvyšuje znečištění
životního prostředí.
! Nepoužívejte prací prostředky určené pro ruční praní,
protože způsobují tvorbu nadměrného množství pěny.
! Pro předrku a praní při teplotě vyšší než 60 °C poívejte
pškové prací prosedky pro lé bavl prádlo.
! Dodržujte pokyny uvedené na obalu pracího prostředku.
Při vytahování dávkovače
pracích prostředků a při
jeho plnění pracími nebo
přídavnými prostředky
postupujte následovně.
přihrádka 1: Nedávejte mycí prostředek v tomto
přihrádka
přihrádka 2: Prací prostředek (práškový anebo teku-
tý) pro praní
Tekutý prací prostředek se nalévá pouze těsně před
uvedením do chodu.
přihrádka 3: Přídavné prostředky (aviváž, atd.)
Aviváž nesmí vytékat z mřížky.
Příprava prádla
• Roztřiďte prádlo podle:
- druhu tkaniny / symbolu na visačce.
- barvy: oddělte barevné prádlo od bílého.
• Vyprázdněte kapsy a zkontrolujte knoíky.
• Nepřekračujte hodnoty povolené náplně, uvedené v
„Tabulka pracích programů“, vztahující se na hmotnost
suchého prádla.
Kolik váží prádlo?
1 prostěradlo 400-500 g
1 povlak na polštář 150-200 g
1 ubrus 400-500 g
1 župan 900-1.200 g
1 ručník 150-250 g
1
2
3
Oděvy vyžadující zvláštní péči
Vlna: S programem 10 je možné prát v pračce všechny
druhy vlněného prádla, také ty, které jsou označené
visačkou „prát pouze v ruce“ . Pro dosažení optimál-
ních výsledků používejte specický prací prostředek a
nepřekračujte 1,5 kg prádla.
Jeans: převraťte prádlo naruby a použijte tekutý prací
prostředek. Použijte program 11.
Systém automatického vyvážení náplně
Před každým odstřeďováním buben provede otáčení ry-
chlostí lehce převyšující rychlost praní, aby se odstranily
vibrace a aby se náplň rovnoměrně rozložila. V případě,
že po několikanásobných pokusech o vyvážení prádlo
ještě nebude správně vyváženo, zařízení provede
odstřeďování nižší rychlostí, než je přednastavená
rychlost. Za přítomnosti nadměrného nevyvážení pračka
provede namísto odstřeďování vyvážení. Za účelem
dosažení rovnoměrnějšího rozložení náplně a jejího
správného vyvážení se doporučuje míchat velké a malé
kusy prádla.
1 / 1

Indesit IWD 61282 C ECO (EU) Užívateľská príručka

Kategória
Práčky
Typ
Užívateľská príručka