Parkside PDT 40 A1 Original Operating Instructions



AIR NAILER / STAPLER SET

Operation and Safety Notes

Original operating instructions

4



KKOMPLET ŽEBLJALNIKA NA

STISNJEN ZRAK

Navodila za upravljanje in varnostna opozorila

Originalna navodila za uporabo

PDT 40 A1



PNEUMATICKÁ SPONKOVAČKA

Pokyny pro obsluhu a bezpečnostní pokyny

Originální návod k obsluze



PNEUMATSKA KLAMERICA

Upute za posluživanje i za Vašu sigurnost

Originalne upute za uporabu



PNEUMATICKÝ SPONKOVAČ

Pokyny pre obsluhu a bezpečnostné pokyny

Originálny návod na obsluhu

  

DRUCKLUFT-TACKER-SET

Bedienungs- und Sicherheitshinweise

Originalbetriebanleitung

Anleitung_4137763:_ 10.05.2010 15:00 Uhr Seite 1

AIR NAILER / STAPLER SET



Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of

the device.



Pred branjem stran s slikami odprite navzven in se nato seznanite z vsemi funkcijami naprave.



Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.



Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.



Prije nego što pročitate tekst, otvorite stranicu sa slikama i upoznajte se na osnovu toga sa svim

funkcijama uređaja.

  

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit

allen Funktionen des Gerätes vertraut.

GB Operation and Safety Notes Page 5

SI Navodila za upravljanje in varnostna opozorila Stran 17

CZ Pokyny pro obsluhu a bezpečnostní pokyny Strana 29

SK Pokyny pre obsluhu a bezpečnostné pokyny Strana 41

HR Upute za posluživanje i za Vašu sigurnost Stranica 53

DE/AT/CH Bedienungs- und Sicherheitshinweise Seite 65

KOMPLET ŽEBLJALNIKA NA

STISNJEN ZRAK

PNEUMATICKÁ SPONKOVAČKA

PNEUMATSKA KLAMERICA

PNEUMATICKÝ SPONKOVAČ

DRUCKLUFT-TACKER-SET

Anleitung_4137763:_ 10.05.2010 15:00 Uhr Seite 2

3

1

E

D

K

I

C

G

H

2 3

A

B

AIR NAILER / STAPLER SET KOMPLET ŽEBLJALNIKA NA

STISNJEN ZRAK

PNEUMATICKÁ SPONKOVAČKA

PNEUMATSKA KLAMERICA

PNEUMATICKÝ SPONKOVAČ

DRUCKLUFT-TACKER-SET

L

N

O

M

F

Anleitung_4137763:_ 10.05.2010 15:01 Uhr Seite 3

4

6 7

2

G

1

8

I

J

4 5

F

Anleitung_4137763:_ 10.05.2010 15:01 Uhr Seite 4

5

GB

The reprinting or reproduction by any other

means, in whole or in part, of documentation

and papers accompanying products is

permitted only with the express consent of the

ISC GmbH.

Subject to technical changes

Table of contents: Page

1. Introduction ..............................................................................7

2. Safety Information ....................................................................7-8

3. Layout ......................................................................................8

4. Items supplied ..........................................................................8

5. Intended use.............................................................................8-9

6. Technical data .........................................................................9-10

7. Starting up ................................................................................10-11

8. Care and maintenance .............................................................12

9. Cleaning and ordering spare parts ...........................................12

10. Disposal and recycling ...........................................................12

11. Excluded from the guarantee .................................................13

12. Declaration of conformity ........................................................14-15

13. Guarantee certificate ..............................................................16

Anleitung_4137763:_ 10.05.2010 15:01 Uhr Seite 5

6

GB

Additional safety instructions

“Caution - Read the operating instructions to reduce the risk of inquiry”

Wear ear-muffs.

The impact of noise can cause damage to hearing.

Wear safety goggles.

Sparks generated during working or splinters, chips and dust emitted by the device

can cause loss of sight.

Do not use on platforms and ladders.

Anleitung_4137763:_ 10.05.2010 15:01 Uhr Seite 6

1. Introduction

 Important.

When using the equipment, a few safety

precautions must be observed to avoid injuries

and damage. Please read the complete

operating manual with due care. Keep this

manual in a safe place so that the information is

available at all times. If you give the equipment

to any other person, hand over these operating

instructions as well. We cannot accept any

liability for damage or accidents which arise

due to a failure to follow these instructions and

the safety information.

2. Safety Information

 CAUTION

Read all the safety regulations and

instructions. Any errors made in following the

safety regulations and instructions may result in

an electric shock, fire and/or serious injury.

Keep all safety regulations and instructions

in a safe place for future use.

Protect yourself and your environment from

accidents by taking the appropriate

precautionary measures.

■ Do not use the stapler for a purpose for

which it is not designed.

■ Keep air tools safe from children.

■ Never use the equipment when you are not

rested or distracted.

■ Connect the compressed air using a quick-

lock coupling only.

■ Staplers may only be connected to

lines/hoses which do not allow the

maximum permitted pressure of the

equipment to be exceeded by more than

10%. A pressure regulator (pressure

reducer) with a downstream pressure

control valve must be fitted to the

compressed air hose if the pressure is

higher.

■ The operating pressure must be adjusted by

a pressure reducer.

■ When using a pneumatically operated

stapler/nailer, only use the pressure

required for the specific operation to prevent

an unnecessarily high noise level,

excessive wear and consequential faults.

■ Never use oxygen or combustible gases as

a power source. Danger of fire and

explosion.

■ Always disconnect the equipment from the

compressed air source before tackling

faults or starting any maintenance work.

■ Use only genuine spare parts. Repairs may

only be carried out by an authorized agent

of the manufacturer or by an alternative

specialist in accordance with the

specifications contained in the operating

instructions.

■ Wear the necessary protective clothing

when working with the stapler, in particular

safety goggles and protective gloves.

■ Do not exceed the maximum air pressure of

8 bar.

■ Do not direct the connected and loaded

nailer at other people.

■ Do not remove the earthing contact device.

■ Never leave the equipment unattended

when loaded.

■ Never use the equipment if defective.

■ Only use the types of staples/nails specified

in the technical data.

■ The equipment must always be

depressurized after disconnection.

■ Never use the equipment without

staples/nails.

■ Never point an operational stapler directly at

yourself or at any other person.

■ Whilst working with the stapler, hold it in

such a way that your head and body cannot

be injured in case of kickback caused by

disruption of the power supply or by hard

areas of the workpiece.

■ Never trigger the stapler into the open air.

This is important to avoid the hazards of

free-flying staples and of overloading the

appliance.

■ For the purposes of transportation, the

stapler must be disconnected from the

compressed-air system, especially if you

are using a ladder or are adopting an

unusual posture.

7

GB

Anleitung_4137763:_ 10.05.2010 15:01 Uhr Seite 7

■ In the workplace, carry the stapler only by

its handle and ensure that the trigger is

inactivated.

■ Make allowance for the workplace

conditions. Staples can potentially go

straight through thin workpieces or they can

slide off workpieces when working on

corners and edges, thus putting persons at

risk.

■ For you own personal safety, always use

suitable protective equipment such as, for

example, hearing and eye protection.

■ Check that the trigger catch functions

correctly every time before you use the

equipment. You are allowed to start using

the equipment only if the device functions

perfectly.

This equipment is not suitable for the following

work:

■ If changing from one stapling point to

another involves moving about on

platforms, steps, ladders or any other

structures similar to ladders such as, e.g.

roof battens.

■ Sealing of boxes or crates.

■ Fitting of transportation braces, e.g. to

vehicles and wagons

Do not lose this safety information.

Residual risks

Even if you use this tool in accordance with

instructions, certain residual risks cannot be

eliminated. The following hazards may arise in

connection with the equipment’s construction

and layout:

1. Risk of pinching.

2. Risk of injury from staples.

3. Damage to hearing, if no suitable ear

protection is applied.

4. Health damage caused by hand-arm

vibrations, if the equipment is not properly

guided and maintained.

3. Layout (Fig. 1)

A Trigger lever

B Compressed air connection

C Magazine lever

D Magazine cover

E Magazine

F Level indicator

G Depth setting

H Trigger catch

I Cover plate (external)

J Cover plate (Internal)

K Swivel air-outlet

4. Items supplied (Fig. 2)

L Safety goggles

M Special compressed air oil

N Allen key, 3 mm

O Allen key, 4 mm

Not illustrated:

■ 250 x 15 mm, 25 mm, 40 mm, 50 mm nails

of each size

■ 250 x 16 mm staples, 500 x 25 mm staples,

250 x 40 mm staples

5. Intended use

The stapler is a pneumatically operated tool

designed for versatile use.

This equipment is designed for driving finishing

nails and staples into wood and similar

materials. Only use the types of nails/staples

described in the “Technical data” section or

illustrated on the information sign on the

magazine. Never use any other nails/staples.

Never use on hard surfaces such as stone,

metal, etc., either.

The equipment may only be used for the tasks it

is designed to handle. Any other use is deemed

to be a case of misuse. The user/operator and

not the manufacturer will be liable for any

damage or injuries of any kind caused as a

result of this.

8

GB

Anleitung_4137763:_ 10.05.2010 15:01 Uhr Seite 8

Please note that our equipment has not been

designed for use in commercial, trade or

industrial applications. Our warranty will be

voided if the equipment is used in commercial,

trade or industrial businesses or for equivalent

purposes.

Only allow repairs and services to be carried

out by authorized professional repair shops.

Remember.

If the inner diameter of the hose is

insufficient and the length of the hose too

long, this will result in a loss of power on

the equipment.

6. Technical data

Max. permitted operating pressure 8 bar

Recommended pressure range 4 - 7.5 bar

Air consumption approx. 0.11 l/shot

Staple width 5.7 mm

Staple length 13 - 40 mm

Nail length 10 - 50 mm

Recommended hose diameter Diameter 9 mm

Weight approx. 1,3 kg

L

pA

sound pressure level 85.5 dB(A)

L

WA

sound power level 98.8 dB(A)

L

PC

sound pressure level 113.6 dB(A)

Vibration a

w

≤ 2.5 m/s

2

K uncertainty 27.93 %

These values for noise emissions are

equipment-based characteristic values and do

not reflect the noise generated at the place of

use. The noise generated at the place of use

will depend, for example, on the work area, the

workpiece, workpiece support and the number

of stapling/nailing operations.

The value given for vibration is an equipment-

based characteristic value and does not

represent the impact on the hand and arm

system when the equipment is used. The

impact on the hand and arm system when the

equipment is used will depend, for example, on

the force of the grip, the pressing force, the

direction in which you are working, the air

pressure setting, the workpiece and the

workpiece support.

Reduce noise generation and vibration to a

minimum!

■ Use only equipment that is in perfect

condition.

■ Maintain and clean the equipment regularly.

■ Adopt your way of working to the

equipment.

■ Do not overload the equipment.

■ Have the equipment checked if necessary.

■ Switch off the equipment when not in use.

■ Wear gloves.

Compressed air quality:

Purified and with oil mist.

Air supply:

Via a conditioning unit with filter pressure

reducer and mist oiler connected to a

compressed air source.

Recommended capacity of the compressor:

Compressor with a capacity of approx. 250

l/min, which is the equivalent of engine power of

approx. 2.2 kW

Remember:

Wear the necessary protective clothing

when working with the stapler, in particular

safety goggles.

Pay attention to the safety regulations.

6.1 Safety goggles (SF026)

The safety goggles (Fig. 2/Item L) are intended

to provide protection for the eyes, against small

parts flying at high speed and are intended to

protect the user against injury.

For optimum protection the safety goggles

should be adjusted by lengthening or

shortening the strap to make them fit correctly.

Adjusting the goggles: Slide the strap along the

latch to adjust the length of the strap.

9

GB

Anleitung_4137763:_ 10.05.2010 15:02 Uhr Seite 9

ID number, name and address of the test

organization

N.B. 0196

Gesellschaft für Konformitätsbewertung mbH

Alboinstrasse 56

12103 Berlin

Explanation of the symbols on the safety

goggles

1: Optical class

F: Mechanical strength (45 m/s)

166: Number of the standard (EN 166)

Cleaning

Clean the goggles at regular intervals using

lukewarm water and a little lubricant soap. Do

not use cleaning agents or solvents; these may

be aggressive to the plastic.

Storage

Do not store the goggles in extremely hot

environments where they may be exposed to

UV radiation. This may reduce the service life of

the plastic. Store the goggles in a cool dark

place when they are not in use.

Working life

Replace the goggles if the viewing screens get

scratched or damaged or if the frame gets

damaged.

Transport

The safety goggles can be kept in the transport

case.

Warnings

If spectacles are worn behind the safety

goggles there is a danger of harm to the user

from the possibility of the transfer of impacts

from particles flying at high speed.

Materials coming into contact with the user’s

skin may cause allergies among people who

are sensitive.

Never work with safety goggles which have a

scratched or damaged viewing screen.

7. Starting up

■ Each time before starting work, check that

the trigger catch functions perfectly and that

all screws and nuts are securely fastened.

■ Never tamper with the stapler.

■ Never dismantle or block any parts of the

stapler such as, e.g. a trigger catch.

■ Never carry out any “emergency repairs”

with unsuitable means.

■ Proper stapler maintenance is required at

regular intervals in accordance with the

information supplied by the manufacturer.

■ Take precautions to prevent anything which

would weaken or damage the equipment,

e.g. from

a) striking or engraving,

b) modifications which are prohibited by the

manufacturer,

c) guiding on templates made of hard material,

e.g. steel,

d) pushing across the floor,

e) using as a hammer,

f) any kinds of acts of violence.

7.1 Checking the trigger catch

Check the trigger catch (Fig. 1/Item H) each

time before use. The trigger catch must move

freely without catching. The spring on the

trigger catch must return the trigger catch to the

released initial position. Never use the

equipment if the trigger catch is not working.

1. Disconnect the equipment from the air

supply.

2. Remove the staples/nails from the

magazine (Fig. 1/Item E).

3. Check that the trigger and the trigger catch

can move up and down freely.

4. Connect the equipment to the air supply.

5. Press the trigger catch against the

workpiece without pressing the trigger. The

equipment should not operate. Never use

the equipment if it operates without the

trigger being pressed. Risk of injury.

6. Remove the equipment from the workpiece.

The trigger catch must return to the

released initial position. Press the trigger.

The equipment should not operate. Never

10

GB

Anleitung_4137763:_ 10.05.2010 15:02 Uhr Seite 10

use the equipment if it operates. Risk of

injury.

7. Press the trigger and press the trigger catch

against the workpiece. The equipment

operates.

8. Press the trigger catch against the

workpiece and press the trigger; the

equipment operates.

7.2 Loading staples and nails

■ When you fill the magazine (Fig. 1/Item E),

make sure that you hold the equipment in

such a way that the muzzle is pointed

neither at you or anyone else.

■ To fill the magazine, press the magazine

lever (Fig. 1 / Item C) and slide back the

magazine cover (Fig. 1 / Item D) as far as it

will go.

■ Insert the staples as shown in (Fig. 3) or the

nails as shown in (Fig. 4).

■ Do not insert more than one complete stick

of staples/nails, otherwise the magazine will

be overfilled and you will not be able to

close it again. Slide the magazine cover

forward again until it snaps into place.

■ The level indicator (Fig. 5 / Item F) shows

the number of loaded staples / nails if less

than 50 are loaded.

7.3 Operation/Operating pressure

■ Connect the pneumatic stapler/nailer to the

compressed air connection (Fig. 1 / Item B).

■ Set the swivel air outlet (Fig. 1 / Item K) to

the desired position.

■ Before starting the stapler, switch on the

compressor and set the operating pressure

on the pressure reducer to 4 bar.

■ The knurled screw (Fig. 6 / Item G) for

precision adjustment must be approximately

in the middle position between Item 1 and 2.

To do so, turn open the knurled screw three

revolutions, starting from Position 1.

■ For the purpose of setting the operating

pressure it is advisable to use a test

workpiece which is similar in structure and

material thickness to the workpieces to be

joined.

■ To staple/nail, place the pneumatic

stapler/nailer against the workpiece and pull

the trigger lever (Fig. 1 / Item A) once and

release it again after each shot.

■ If the nail or the staple goes in too deep,

reduce the operating pressure on the

pressure reducer by 0.5 bar.

■ If the nail or the staple does not go in deep

enough or projects, increase the operating

pressure on the pressure reducer by 0.5

bar.

■ Place the stapler/nailer against the test

workpiece again and fire.

■ Depending on results, keep changing the

operating pressure in 0.5 bar increments

until the depth that the staples or nails are

driven in is roughly correct. For precision

adjustment (Para. 7.4), use the knurled

screw.

■ The equipment also has an automatic

mode. If you keep the trigger lever pressed,

the staples/nails will be shot automatically

when the pneumatic stapler/nailer is placed

against the workpiece.

■ To prevent faults, make sure that you do not

staple at the same point twice.

Important:

If a staple or nail becomes jammed in the feed

shaft, always immediately depressurize the

equipment first (remove the compressed air

supply hose), open the magazine shaft and

only then remove the cover plates (Fig. 8 / Item

I/J) by undoing the screws with the supplied

Allen keys (Fig. 2 / Item N) (Fig. 7 / 8). Remove

the jammed staples, clean the shaft if

necessary, and close again in reverse order.

7.4 Precision adjustment

■ The equipment has a depth setting adjuster

(Fig. 6 / Item G) in the form of a knurled

screw.

■ If you screw it downwards (Fig. 6 / Item 1),

the staples/nails will be shot in deeper.

■ If you want to reduce the depth that the

staples/nails are shot in, you have to screw

the knurled screw upwards (Fig. 6 / Item 2).

Important: To prevent triggering

unintentionally, the depth setting must never be

pulled back by hand in normal operation.

11

GB

Anleitung_4137763:_ 10.05.2010 15:02 Uhr Seite 11

8. Care and maintenance

Important: Disconnect the equipment from the

compressed air system each time before

starting to carry out maintenance and cleaning

work.

Compliance with the maintenance instructions

given here will ensure that this quality product

has a long service life and offers failure-free

operation.

Before starting work each time, check that the

magazine is securely fastened (Fig. 1/Item E).

Clean the equipment thoroughly immediately

after you have finished the work.

To ensure that your stapler offers lasting perfect

service, it requires regular lubrication. Use the

supplied oil (Fig. 2 / Item M) for this purpose.

There are two possible means of

lubrication:

8.1 By mist oiler

A complete conditioning unit contains a mist

oiler and is fitted to the compressor.

8.2 By hand

If your system has neither a conditioning unit or

a line oiler, 3-5 drops of oil have to be applied to

the compressed air connection each time

before the air tool is started up. If the air tool is

not used for several days, apply 5-10 drops of

oil to the compressed air connection before

switching on.

Store your air tool in a dry room only.

8.3 Other maintenance work

There are no parts inside the equipment which

require additional maintenance.

9. Cleaning and ordering spare

parts

Important: Disconnect the equipment from the

compressed air system each time before

starting to carry out maintenance and cleaning

work.

9.1 Cleaning

■ Keep the trigger catch (Fig. 1/Item H) free of

dirt and dust as far as possible. Wipe the

equipment with a clean cloth or blow it down

with compressed air at low pressure.

■ We recommend that you clean the

equipment immediately after you use it.

■ Clean the equipment regularly with a damp

cloth and some soft soap. Do not use

cleaning agents or solvents; these may be

aggressive to the plastic parts in the

equipment. Ensure that no water can get

into the interior of the equipment.

9.2 Ordering replacement parts

Please provide the following information on all

orders for spare parts:

■ Model/type of the equipment

■ Article number of the equipment

■ ID number of the equipment

For our latest prices and information please go

to www.isc-gmbh.info

10. Disposal and recycling

The equipment is supplied in packaging to

prevent it from being damaged in transit. The

raw materials in this packaging can be reused

or recycled. The equipment and its accessories

are made of various types of material, such as

metal and plastic. Defective components must

be disposed of as special waste. Ask your

dealer or your local council.

12

GB

Anleitung_4137763:_ 10.05.2010 15:02 Uhr Seite 12

11. Excluded from the guarantee

are:

■ Wear parts

■ Damage caused by inadmissible operating

pressure.

■ Damage caused by compressed air which

has not been conditioned.

■ Damage caused by improper use or

unauthorized intervention.

13

GB

Anleitung_4137763:_ 10.05.2010 15:02 Uhr Seite 13

14

GB

12. Declaration of conformity

k erklärt folgende Konformität gemäß EU-Richtlinie und

Normen für Artikel

t explains the following conformity according to EU

directives and norms for the following product

p déclare la conformité suivante selon la directive CE et les

normes concernant l’article

C dichiara la seguente conformità secondo la direttiva UE e

le norme per l’articolo

N verklaart de volgende overeenstemming conform EU

richtlijn en normen voor het product

m declara la siguiente conformidad a tenor de la directiva y

normas de la UE para el artículo

O declara a seguinte conformidade, de acordo com a

directiva CE e normas para o artigo

l attesterer følgende overensstemmelse i medfør af

EU-direktiv samt standarder for artikel

U förklarar följande överensstämmelse enl. EU-direktiv och

standarder för artikeln

q vakuuttaa, että tuote täyttää EU-direktiivin ja standardien

vaatimukset

. tõendab toote vastavust EL direktiivile ja standarditele

j vydává následující prohlášení o shodě podle směrnice

EU a norem pro výrobek

X potrjuje sledečo skladnost s smernico EU in standardi za

izdelek

W vydáva nasledujúce prehlásenie o zhode podľa smernice

EÚ a noriem pre výrobok

A a cikkekhez az EU-irányvonal és Normák szerint a

következő konformitást jelenti ki

P deklaruje zgodność wymienionego poniżej artykułu z

następującymi normami na podstawie dyrektywy WE.

e декларира съответното съответствие съгласно

Директива на ЕС и норми за артикул

H paskaidro šādu atbilstību ES direktīvai un standartiem

G apibūdina šį atitikimą EU reikalavimams ir prekės

normoms

Q declară următoarea conformitate conform directivei UE

şi normelor pentru articolul

z δηλώνει την ακόλουθη συμμόρφωση σύμφωνα με την

Οδηγία ΕΚ και τα πρότυπα για το προϊόν

B potvrđuje sljedeću usklađenost prema smjernicama EU

i normama za artikl

f potvrđuje sljedeću usklađenost prema smjernicama EU

i normama za artikl

4 potvrđuje sledeću usklađenost prema smernicama EZ i

normama za artikal

T следующим удостоверяется, что следующие

продукты соответствуют директивам и нормам ЕС

1 проголошує про зазначену нижче відповідність

виробу директивам та стандартам ЄС на виріб

5 ја изјавува следната сообрзност согласно

ЕУ-директивата и нормите за артикли

Z Ürünü ile ilgili AB direktifleri ve normları gereğince

aşağıda açıklanan uygunluğu belirtir

L erklærer følgende samsvar i henhold til EU-direktivet

og standarder for artikkel

E Lýsir uppfyllingu EU-reglna og annarra staðla vöru

Konformitätserklärung

Einhell Germany AG · Wiesenweg 22 · D-94405 Landau/Isar

Druckluft-Tacker/Nagler PDT 40 A1 (Parkside)

Standard references: EN 792-13

Landau/Isar, den 04.02.2010

First CE: 10 Archive-File/Record: 4137760-09-4155050-10

Art.-No.: 41.377.63 I.-No.: 11010 Documents registrar: Siegfried Roider

Subject to change without notice Wiesenweg 22, D-94405 Landau/Isar

Weichselgartner/General-Manager Wang/Product-Management

2009/105/EC

2006/95/EC

2006/28/EC

2005/32/EC

2004/108/EC

2004/22/EC

1999/5/EC

97/23/EC

90/396/EC

89/686/EC_96/58/EC

x

2006/42/EC

2004/26/EC

Emission No.:

2000/14/EC_2005/88/EC

Annex IV

Notified Body:

Notified Body No.:

Reg. No.:

Annex V

Annex VI

Noise: measured L

WA

= dB (A); guaranteed L

WA

= dB (A)

P = KW; L/Ø = cm

Notified Body:

Anleitung_4137763:_ 10.05.2010 15:02 Uhr Seite 14

15

GB

12. Declaration of conformity

k erklärt folgende Konformität gemäß EU-Richtlinie und

Normen für Artikel

t explains the following conformity according to EU

directives and norms for the following product

p déclare la conformité suivante selon la directive CE et les

normes concernant l’article

C dichiara la seguente conformità secondo la direttiva UE e

le norme per l’articolo

N verklaart de volgende overeenstemming conform EU

richtlijn en normen voor het product

m declara la siguiente conformidad a tenor de la directiva y

normas de la UE para el artículo

O declara a seguinte conformidade, de acordo com a

directiva CE e normas para o artigo

l attesterer følgende overensstemmelse i medfør af

EU-direktiv samt standarder for artikel

U förklarar följande överensstämmelse enl. EU-direktiv och

standarder för artikeln

q vakuuttaa, että tuote täyttää EU-direktiivin ja standardien

vaatimukset

. tõendab toote vastavust EL direktiivile ja standarditele

j vydává následující prohlášení o shodě podle směrnice

EU a norem pro výrobek

X potrjuje sledečo skladnost s smernico EU in standardi za

izdelek

W vydáva nasledujúce prehlásenie o zhode podľa smernice

EÚ a noriem pre výrobok

A a cikkekhez az EU-irányvonal és Normák szerint a

következő konformitást jelenti ki

P deklaruje zgodność wymienionego poniżej artykułu z

następującymi normami na podstawie dyrektywy WE.

e декларира съответното съответствие съгласно

Директива на ЕС и норми за артикул

H paskaidro šādu atbilstību ES direktīvai un standartiem

G apibūdina šį atitikimą EU reikalavimams ir prekės

normoms

Q declară următoarea conformitate conform directivei UE

şi normelor pentru articolul

z δηλώνει την ακόλουθη συμμόρφωση σύμφωνα με την

Οδηγία ΕΚ και τα πρότυπα για το προϊόν

B potvrđuje sljedeću usklađenost prema smjernicama EU

i normama za artikl

f potvrđuje sljedeću usklađenost prema smjernicama EU

i normama za artikl

4 potvrđuje sledeću usklađenost prema smernicama EZ i

normama za artikal

T следующим удостоверяется, что следующие

продукты соответствуют директивам и нормам ЕС

1 проголошує про зазначену нижче відповідність

виробу директивам та стандартам ЄС на виріб

5 ја изјавува следната сообрзност согласно

ЕУ-директивата и нормите за артикли

Z Ürünü ile ilgili AB direktifleri ve normları gereğince

aşağıda açıklanan uygunluğu belirtir

L erklærer følgende samsvar i henhold til EU-direktivet

og standarder for artikkel

E Lýsir uppfyllingu EU-reglna og annarra staðla vöru

Konformitätserklärung

Einhell Germany AG · Wiesenweg 22 · D-94405 Landau/Isar

Schutzbrille SF 026

Standard references: EN 166

Landau/Isar, den 24.02.2010

First CE: 10 Archive-File/Record: 4137760-09-4155050-10

Art.-No.: 41.377.63 I.-No.: 11010 Documents registrar: Siegfried Roider

Subject to change without notice Wiesenweg 22, D-94405 Landau/Isar

Weichselgartner/General-Manager Wang/Product-Management

x

2009/105/EC

2006/95/EC

2006/28/EC

2005/32/EC

2004/108/EC

2004/22/EC

1999/5/EC

97/23/EC

90/396/EC

89/686/EC_96/58/EC

2006/42/EC

2004/26/EC

Emission No.:

2000/14/EC_2005/88/EC

Annex IV

Notified Body:

Notified Body No.:

Reg. No.:

Annex V

Annex VI

Noise: measured L

WA

= dB (A); guaranteed L

WA

= dB (A)

P = KW; L/Ø = cm

Notified Body:

Anleitung_4137763:_ 10.05.2010 15:02 Uhr Seite 15

16

GB

13. GUARANTEE CERTIFICATE

Dear Customer,

All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely

event that your device develops a fault, please contact our service department at the address shown on this

guarantee card. Of course, if you would prefer to call us then we are also happy to offer our assistance under

the service number printed below. Please note the following terms under which guarantee claims can be made:

1. These guarantee terms cover additional guarantee rights and do not affect your statutory warranty rights.

We do not charge you for this guarantee.

2. Our guarantee only covers problems caused by material or manufacturing defects, and it is restricted to the

rectification of these defects or replacement of the device. Please note that our devices have not been

designed for use in commercial, trade or industrial applications. Consequently, the guarantee is invalidated

if the equipment is used in commercial, trade or industrial applications or for other equivalent activities. The

following are also excluded from our guarantee: compensation for transport damage, damage caused by

failure to comply with the installation/assembly instructions or damage caused by unprofessional

installation, failure to comply with the operating instructions (e.g. connection to the wrong mains voltage or

current type), misuse or inappropriate use (such as overloading of the device or use of non-approved tools

or accessories), failure to comply with the maintenance and safety regulations, ingress of foreign bodies

into the device (e.g. sand, stones or dust), effects of force or external influences (e.g. damage caused by

the device being dropped) and normal wear resulting from proper operation of the device.

This applies in

particular to rechargeable batteries for which we nevertheless issue a guarantee period of 12 months.

The guarantee is rendered null and void if any attempt is made to tamper with the device.

3. The guarantee is valid for a period of 3 years starting from the purchase date of the device. Guarantee

claims should be submitted before the end of the guarantee period within two weeks of the defect being

noticed. No guarantee claims will be accepted after the end of the guarantee period. The original guarantee

period remains applicable to the device even if repairs are carried out or parts are replaced. In such cases,

the work performed or parts fitted will not result in an extension of the guarantee period, and no new

guarantee will become active for the work performed or parts fitted. This also applies when an on-site

service is used.

4. In order to assert your guarantee claim, please send your defective device postage-free to the address

shown below. Please enclose either the original or a copy of your sales receipt or another dated proof of

purchase. Please keep your sales receipt in a safe place, as it is your proof of purchase. It would help us if

you could describe the nature of the problem in as much detail as possible. If the defect is covered by our

guarantee then your device will either be repaired immediately and returned to you, or we will send you a

new device.

Of course, we are also happy offer a chargeable repair service for any defects which are not covered by the

scope of this guarantee or for units which are no longer covered. To take advantage of this service, please send

the device to our service address.

Anleitung_4137763:_ 10.05.2010 15:02 Uhr Seite 16

17

SI

Kazalo Stran

1. Uvod .......................................................................................19

2. Varnostni napotki ...................................................................19-20

3. Opis naprave ..........................................................................20

4. Obseg dobave ........................................................................20

5. Predpisana namenska uporaba ..............................................20-21

6. Tehnični podatki .....................................................................21-22

7. Prvi zagon ..............................................................................22-24

8. Vzdrževanje in nega ...............................................................24

9. Čiščenje in naročanje nadomestnih delov ..............................24

10. Odstranjevanje in ponovna uporaba ......................................25

11. Izključeno iz garancije ............................................................25

12. Izjava o skladnosti...................................................................26-27

13. Garancijska listina ..................................................................28

Ponatis ali kakršnokoli razmnoževanje

dokumentacije in spremljajočih papirjev o

proizvodu, tudi po izvlečkih, je dovoljeno samo

z izrecnim soglasjem ISC GmbH.

Pridržana pravica do tehničnih sprememb

Anleitung_4137763:_ 10.05.2010 15:02 Uhr Seite 17

18

SI

Dodatni varnostni napotki

OPOZORILO - Za zmanjšanje tveganja poškodb preberite navodila za uporabo stroja

Uporabljajte zaščito za ušesa.

Učinkovanje hrupa lahko povzroči izgubo sluha.

Uporabljajte zaščitna očala.

Med delom nastajajoče iskre ali iz naprave izletajoči delčki, ostružki in prah lahko

povzročijo izgubo vida.

Ne uporabljajte na gradbenih odrih ali lestvah.

Anleitung_4137763:_ 10.05.2010 15:02 Uhr Seite 18

1. Uvod

 Pozor!

Pri uporabi naprav je potrebno upoštevati nekaj

varnostnih ukrepov, da bi preprečili poškodbe

in materialno škodo. Zato skrbno preberite ta

navodila za uporabo. Le-te dobro shranite tako,

da boste imeli zmeraj pri roki potrebne

informacije. Če bi napravo izročili drugim

osebam, Vas prosimo, da jim izročite tudi ta

navodila za uporabo. Ne prevzemamo nobene

odgovornosti za nezgode ali škodo, ki bi

nastale zaradi neupoštevanja teh navodil za

uporabo in varnostnih napotkov.

2. Varnostni napotki

 OPOZORILO

Preberite vse varnostne napotke in

navodila. V primeru, da tega ne storite, so

lahko posledica električni udar, požar in/ali

hude poškodbe.

Shranite vse varnostne napotke in navodila

za kasnejšo uporabo.

Zaščitite sebe in Vaše okolje s primernimi

varnostnimi ukrepi pred nevarnostjo nezgod.

■ Pribijača ne uporabljajte za druge namene.

■ Pnevmatska orodja zavarujte pred otroki.

■ Na delo se odpravite samo spočiti in zbrani.

■ Priključek za komprimirani zrak izvršite

samo preko hitro zapiralnega spoja

■ Naprave za zabijanje smejo biti priključene

samo na cevi, v katerih ne more biti največji

dopustni tlak naprave več kot 10 %. Pri

večjih tlakih mora biti v pnevmatski cevi

inštalirani tlačni regulacijski ventil (reducirni

ventil) s priključenim ventilom za

omejevanje tlaka.

■ Nastavitev delovnega tlaka se mora izvršiti

preko reducirnega ventila.

■ Pnevmatske naprave za zabijanje

uporabljajte samo z ustreznim tlakom za

določeno delovno opravilo tako, da boste

preprečili nepotrebno visoki nivo hrupnosti,

povečano obrabo in iz tega izhajajoče

motnje.

■ Kot energetski ne smete uporabljati kisika

ali vnetljivih plinov. Obstaja nevarnost

požara in eksplozije.

■ Pred odpravo motenj in vzdrževalnimi deli

odklopite napravo od vira komprimiranega

zraka.

■ Uporabljajte samo originalne nadomestne

dele. Popravila sme izvajati samo s strani

proizvajalca pooblaščene osebe ali drugi

strokovnjaki z upoštevanjem v navodilih za

uporabo navedenih navedb.

■ Pri delu s pribijačem uporabljajte potrebno

zaščitno obleko, še posebej zaščitna očala

in zaščitne rokavice.

■ Najvišji komprimirani zrak sme biti 8 bar

■ Priključenega in nabitega žebljalnika ne

usmerjajte proti ljudem.

■ Ne odstranjujte zaščitne kontaktne opreme.

■ Nabite naprave ne puščajte brez nadzora.

■ Ne uporabljajte pokvarjenih naprav.

■ Uporabljajte samo sponke/žeblje kot je

navedeno v tehničnih podatkih.

■ Po odklopu ne sme biti naprava pod tlakom.

■ Nikoli ne uporabljajte naprave brez

sponk/žebljev.

■ Nikoli ne usmerjajte nabite naprave za

zabijanje neposredno proti sebi ali proti

drugim osebam.

■ Pri delu držite napravo za zabijanje tako, da

si ne boste mogli poškodovati glave in

telesa v primeru morebitnega vzvratnega

sunka zaradi kakšne motnje pri napajanju z

energijo ali trdih mest v obdelovancu.

■ Nikoli ne sprožajte naprave za zabijanje v

prazni prostor. Na ta način boste preprečili

ogrožanje zaradi prostoletečin predmetov

zabijanja in preobremenitev naprave.

■ Pred transportom morate odklopiti napravo

za zabijanje od pnevmatskega omrežja, še

posebej, če uporabljate lestve ali se

premikate pri neobičajni drži telesa.

■ Na delovnem mestu prenašajte napravo za

zabijanje samo za ročaj in z neaktiviranim

sprožilom.

■ Pazite na pogoje na delovnem mestu.

Predmeti za zabijanje lahko prebijejo

eventuelno tanke obdelovance ali pa

zdrsnejo vstran pri delu na kotih in robovih

in s tem ogrožajo ljudi.

19

SI

Anleitung_4137763:_ 10.05.2010 15:02 Uhr Seite 19

■ Za Vašo osebno zaščito uporabljajte

primerna sredstva za zaščito telesa, kot npr.

zaščita za ušesa in oči.

■ Pred vsakim začetkom uporabe morate

preveriti pravilno delovanje sprožilnega

varovala. Napravo smete začeti uporabljati

samo, če sprožilno varovalo deluje

brezhibno.

Naprava ni primerna za sledeča dela:

■ Če prihaja do menjave mesta zabijanja iz

enega na drugo preko delovnih odrov,

stopnic, lestev ali lestvam podobnih

konstrukcij, kot npr. deskane strešne

konstrukcije,

■ zapiranje zabojev ali lesenih pregrad,

■ pri nameščanju transportnih varoval, npr. na

vozilih in vagonih

Ta varnostna navodila dobro shranite.

Ostala tveganja

Tudi, če delate s tem orodjem po predpisih,

zmeraj obstaja nekaj ostalih tveganj. Nastopijo

lahko sledeče nevarnosti v zvezi s konstrukcijo

in izvedbo tega električnega orodja:

1. Nevarnost zmečkanin

2. Nevarnost poškodb zaradi predmetov za

zabijanje

3. Poškodbe sluha, če ne uporabljate primerne

zaščite za ušesa.

4. Poškodbe zdravja, ki nastajajo zaradi

vibracij v rokah in dlaneh, če naprava ni

pravilno vodena in vzdrževana.

3. Opis naprave (Slika 1)

A Sprožilna ročica

B Priključek za komprimirani zrak

C Ročica okvira za sponke/žeblje

D Pokrov okvira za sponke/žeblje

E Okvir za sponke/žeblje

F Prikaz napolnjenosti

G Globinska nastavitev

H Sprožilno varovalo

I Pokrovna plošča zunaj

J Pokrovna plošča znotraj

K Vrtljivi izpust za zrak

4. Obseg dobave (Sl. 2)

L Zaščitna očala

M Pnevmatsko specialno olje

N Inbus ključ 3 mm

O Inbus ključ 4 mm

brez slike:

■ po 250 kom žebljev, 15 mm, 25 mm, 40

mm, 50 mm

■ po 250 kom sponk 16 mm, 500 kom 25 mm,

250 kom 40 mm

5. Predpisana namenska

uporaba

Pribijač je pnevmatsko delujoče orodje za

mnogostransko uporabo.

Ta naprava služi zabijanju vgreznjenih žebljev

in sponk v les in podobne materiale. Uporabljati

smete samo žeblje oz. sponke, ki so opisane

pod točko “Tehnični podatki” oz. so prikazani

na okvirju za sponke/žeblje. Drugih predmetov

za zabijanje ne smete uporabljat. Prav tako ni

dovoljena uporaba na trdih materialih kot so

kamen, kovina, itd.

Napravo je dovoljeno uporabljati samo za

namene, za katere je bila izdelana. Vsaka

druga uporaba šteje kot nenamenska

nedovoljena uporaba. Za kakršnekoli poškodbe

20

SI

Anleitung_4137763:_ 10.05.2010 15:02 Uhr Seite 20

Stránka sa načítava ...

Parkside PDT 40 A1 Original Operating Instructions

Parkside PDT 40 A1 Original Operating Instructions

Súvisiace články

Ďalšie dokumenty