Worx WG546E.9 Používateľská príručka

INSTALLATION

GUIDE

Installation guide EN P04

Installationsanleitung D P20

Guide d'installation F P36

Guida d'installazione I P52

Guía de instalación ES P68

Installatiegids NL P84

Instrukcja instalacji PL P100

Průvodce instalací CZ P116

Sprievodca inštaláciou SK P132

Navodila za namestitev SL P148

Guia de instalação PT P164

4

EN

How to install your Landroid

®

M

The installation of the Landroid

®

M is easy. Depending on the size of your garden, the entire process only

takes a short amount of time. If you are like us, you hate wasting your time to mow your lawn. The

Landroid

®

M will prove to be a great investment, providing you with years of lawn care.

You can watch the installation demo video at www.worxLandroid.com.

The Landroid

®

M loves to mow

It is designed to mow often, maintaining a healthier and better looking lawn than ever before. Depending on the

size of your lawn, the Landroid

®

M may be programmed to operate at any time or frequency with no restrictions.

It is here to work for you.

5

EN

In the box

Preparation

From your shed

Distance gauge

Hex key

Scissors Hammer

Landroid

®

MCharging base

Base ﬁxing

nails

Wire pegs

Boundary

wire reel

Owner’s manual

Warranty

statement

Installation

guide

Spare blades

Power Adaptor

Programming and

trouble shooting

guide

6

EN

Landroid

®

M's new home-your garden

Let's start by having a closer look at Landroid

®

M’s new home—your lawn—highlighting the areas where it

can safely go and areas it’s best for Landroid

®

M to avoid.

When hitting any obstacle that’s rigid, stable and taller than

15cm—such as a wall or a fence—your Landroid

®

M will simply

stop and re-direct away from the obstacle.

Obstacles that can be hit

Stones that are heavy enough not to be moved by your

Landroid

®

M can be safely hit. However, if any stone has an

inclined surface that your Landroid

®

M can climb, you should

either remove it or exclude it from the working area.

Stones

If your driveway is level with your lawn, without any protruding surface,

the Landroid

®

M can freely run over it. If you'd like the Landroid

®

M to

avoid it, then only a 10cm* space between the Boundary Wire and the

driveway is needed.

If it’s covered with gravel, you should not allow the Landroid

®

M to

travel over it, using the distance gauge for spacing in this case, keeping

a 35cm* space between the boundary wire and the driveway.

* This is the recommended distance. Use the provided distance gauge

to ensure proper installation.

Driveways

You certainly don’t want your Landroid

®

M to mow your ﬂowers,

or fall into the water. These areas should be avoided.

Flowerbeds, ponds, pools...

7

EN

35% (20°)

If there are roots emerging from the ground, these areas should

be avoided in order not to damage the roots.

Trees

In the case of large bumps or dips, please consider if the blades

could touch the ground; if this is the case, either make the

inclines smoother or exclude those areas from your Landroid

®

M’s

operation.

Depressions and bumps

Your Landroid

®

M has the ability to safely climb slopes up to 35%

(20°), so just avoid anything steeper than this.

Slopes

The Upper Boundary Wire should NOT be placed on slopes

steeper than 35% (20°). The Upper Boundary Wire should have

a distance of at least 35cm between any obstacles. The Lower

Boundary Wire should NOT be placed on slopes steeper than

25% (15°). The Lower Boundary Wire should have a distance of

at least 45cm between any obstacles when it is positioned on a

slope that is 25%.

Placement of Boundary Wire on slopes

Upper boundary wire

Lower boundary

Wire

Lower boundary

Wire

8

EN

10cm

35cm

>1m

Installation

See details on step 2.2

See details on step 2.1

See details on step 2.3

See details on step 1 & 3

CHARGING

BASE

9

EN

10cm

35cm

>1m

See details on step 2.5

See details on step 2.7

See details on

step 2.4

10

EN

First of all, ﬁnd a spot for the charging base, taking into account the position of your outdoor socket since the charging base only has a

15m power cord.

NOTE: Make sure the adaptor and the electrical socket are always kept in a dry area.

Your Landroid

®

M needs to know where to mow. This is why you have to mark its working area with a boundary wire

that will form an invisible fence. This wire will also guide your Landroid

®

M to its charging base.

If your neighbor also uses a Landroid

®

M , then you must keep a space of at least 0.5 metres between your

Boundary Wire and your neighbor's.

The charging base should be placed along a straight line, with

the “IN” arrow pointing to the lawn. Allow 2m distance with no

obstacles both front and back of the charging base. If possible,

place the charging base in the shade, as batteries are better

recharged in a cool place.

1.1

Make sure that your Landroid

®

M can run on a ﬂat area, clear of

any obstacles.

Feed the boundary wire through the tunnel underneath the

charging base.

1.2

1. Placing the Charging Base

11

EN

When pegging the boundary wire for the ﬁrst time, it is recommended to use a normal lawn mower or a grass

trimmer to cut the grass along the boundary. Then the wire can be laid as close as possible to the ground to prevent

the Landroid

®

M accidentally cutting the wire. The boundary wire is powered with a very low voltage so that it is

totally safe to people beings and pets.

2. Pegging your boundary wire

NOTE: Keep the boundary wire straight and tight between the

pegs, there should be no slack wire between the pegs.

When laying the boundary

wire, use the distance

gauge to keep a 35cm*

space between the wire and

the boundary.

Each wire peg should be

placed around 80cm apart.

Use the provided distance

gauge to ensure proper

installation.

NOTE: The maximum

permitted length for the

boundary wire is 350m.

2.1

80cm

12

EN

2.3

If there is an island that sits inside your lawn where you don't want

Landroid

®

M to go, please follow the path as shown in the picture

to peg your wire.

The wire should run from the perimeter to outline the deﬁned

island and then return back to the perimeter. The boundary wire

between the island and perimeter should be laid close together

and held in place by the same wire peg. During operation, the

Landroid

®

M will be able to freely pass over this part of the wire.

2.2

A feature, such as ﬂowers or shrubs that are close to the mowing

boundary, should be part of the boundary as shown in the picture.

10cm

35cm

>1m

13

EN

If your lawn has two or more separate areas connected to each

other by a corridor, it should be at least 1 metre wide. If the

corridor is too narrow, please pick your Landroid

®

M up and bring it

to the other lawn. Landroid

®

M will mow this lawn without problem,

but you have to bring it back to the charging base when the battery

runs out.

2.7

>90º >90º

<90º

Ensure the Boundary Wire is perfectly straight in each corner,and

the angle of boundary wire is bigger than 90°.

In the case of an obstacle that is level with ground and safe for the

Landroid

®

M to run over, such as a driveway or path, then only a

10cm* space is needed.

In the case of two islands that are close to each other, it would be

convenient to lay out the wire as illustrated in the picture.

The Landroid

®

M can travel freely over the boundary wire in

between the islands and the mowing boundary.

2.6

2.5

2.4

10cm

35cm

>1m

10cm

35cm

>1m

35cm

>1m

<1m

14

EN

3. Connect the base to the boundary wire

Cut the end of the wire to a length that’s appropriate

convenient for reaching the clamps.

NOTE: Too long redundant wire may cause the signal problem.

Strip the two ends of the wire.

3.1

When connecting to the charging base there is an IN wire

and an OUT wire, as shown. Connect the IN-wire to the red

clamp of the charging base and the OUT-wire to the black

clamp. Then close the cover.

NOTE: Please ﬁx the boundary wire around the charging

base ﬁrmly with the wire pegs.

3.2

OUT

IN

OUT

IN

15

EN

You can now permanently fix the charging base on the ground

by pressing the supplied Base Retention Pegs with the

supplied Hex key.

NOTE: Make sure the IN-wire is running straight

underneath the center of the charging base.

3.3

Connect the power cord to the adaptor and then to the AC

electrical socket, the LED on the charging base will turn

on. When connecting, align the notch on the power cord

connector (a) with the groove on the adaptor connector (b).

In case the power cord is within the working area, you may

bury it as needed.

Check the LED status to make sure the connection is OK.

3.4

a

b

LED light display Status Action

Green light on Boundary wire is connected successfully;

fully charged

/

Green light on, while “outside working

area” shown in the screen at the same

time

Boundary wire is connected in wrong

direction.

Check and reverse two ends of

boundary wire.

Green light flashing Power supply is connected successfully,

while the wire is connected unsuccessfully

Check and connect the wire again.

Red light on Charging /

16

EN

09:00pm

Wed. 6-8-2012

7:00am ~ 12:00am

M T W T F S S

09:00pm

Wed. 6-8-2012

7:00am ~ 12:00am

M T W T F S S

09:00pm

Wed. 6-8-2012

7:00am ~ 12:00am

M T W T F S S

09:00pm

Wed. 6-8-2012

7:00am ~ 12:00am

M T W T F S S

09:00pm

Wed. 6-8-2012

7:00am ~ 12:00am

M T W T F S S

09:00pm

Wed. 6-8-2012

7:00am ~ 12:00am

M T W T F S S

09:00pm

Wed. 6-8-2012

7:00am ~ 12:00am

M T W T F S S

09:00pm

Wed. 6-8-2012

7:00am ~ 12:00am

M T W T F S S

Open the panel cover, press

power button,

then input the default PIN

0000.

Press the

key and close

the control panel cover: your

Landroid

®

M will now

ﬁnd its way to the charging base.

Watch the Landroid

®

M as

it returns to the charging

base and modify the

positioning of the boundary

wire if necessary. When the

Landroid

®

M successfully

returns to the charging base,

this means the installation has

been successfully completed!

Now your Landroid

®

M will

start to fully charge.

4.2

• If your Landroid

®

M

is outside its territory,

it will not move and

the display will indicate

“outside working area”

error. Just move it inside

its territory and repeat

step 4.2

• If your Landroid

®

M is

inside its territory but

the display says “outside

working area” and the

LED is on, it means you

clamped the boundary

wire ends incorrectly.

Just reverse them.

• Your Landroid

®

M

should always remain

switched on. If you ever

need to turn it off, then

make sure you place it

within its boundary area

before you switch it back

on again.

• Should your

Landroid

®

M stop

operating unexpectedly,

just press its ON/OFF

key to ON, correct the

problems, press Start

button and close the

cover.

NOTE: Please refer to the Programming and Troubleshooting Guide for more information.

Warning

4. Turn on and test the installation

Place your Landroid

®

M inside the

working area, a few meters from

the back of the charging base.

4.1

This is the exciting part where you can turn your Landroid

®

M on for the ﬁrst time.

17

EN

Programming

Having the installation ﬁnished, please refer to the Programming and Troubleshooting Guide included in the packaging to program

the Landroid

®

M

.

Ready to go?

The Landroid

®

M is designed for maintaining your grass at a perfect length during the season, but is not designed for deforesting a jungle.

Before starting it for the ﬁrst time,

1. You should mow your lawn to the desired height.

2. Make sure the operating area is clear of objects such as toys and branches...

3. Adjust the cutting height to its maximum level for the ﬁrst mow and then adjust to your preferred lawn grass height.

Next Spring, let your Landroid

®

M start mowing early, when the grass is still short, so that you can avoid a preliminary grass cut.

18

EN

Keep it sharp

Always wear gloves when adjusting the blades.

The Landroid

®

M does not cut grass like other mowers. Its Blades are razor sharp on edges and spin

in both directions for maximum cutting capacity. Each blade of your Landroid

®

M has 2 cutting edges.

Depending on the frequency the Landroid

®

M mows your lawn, the cutting blades will need to be

rotated periodically for a new cutting edge. If your Landroid

®

M is programmed to mow the lawn every

day then the cutting blades will need to be rotated monthly for the best mowing results. Each cutting

blade will last up to 2 months when it is programmed to mow every day. When the cutting blades are

dull and worn out, they should be replaced with the spare blades provided with your Landroid

®

M.

Spare blades are also available at your nearest WORX retailer.

Maintenance

Your Landroid

®

M is engineered and built to stay outdoors regardless of adverse conditions. Just

periodically clean its deck from grass clipping build ups and your Landroid

®

M will mow for you trouble-

free, year after year, season after season. Don't wash Landroid

®

M or Landroid

®

M charger or charging

station with high pressure water washers. This may cause damage to the machine, battery or charger.

Write your PIN code here:

Winter storage

Even though it is tough, we would recommend that you store your Landroid

®

M in your shed or garage

during the Winter. Before storing it, give your Landroid

®

M a full recharge that will preserve its battery

from damage. You can then disconnect the plug of the charging base. A good tip to prolong the life of

the battery is to periodically re-charge it during the Winter. We'd also suggest that you cover the base

with a nylon sheet in winter time.

Safety

Your Landroid

®

M is safe to people beings and pets. First of all, there’s a large clearance between the

outer border of the machine and the blades. Moreover, the tilt sensors will instantly stop the blades if

the unit is lifted from the ground.

Security

Your Landroid

®

M is protected by a PIN code. This PIN code prevents unauthorised people from being

able to use it. Once it’s taken outside its territory, it will not be possible to re-start it by anyone who

does not know the PIN code. This also means that you will not be able to start your Landroid

®

M if

you forget your PIN code! We strongly recommend that you write your PIN code here for future

reference. Even better, register your Landroid

®

M online at www.worxLandroid.com and record your

PIN code there. You'll be able to access your PIN code online any time.

1

2

20

D

So installieren Sie Ihren Landroid

®

M

Die Installation des Landroid

®

M ist ganz einfach. Je nach Größe Ihres Gartens nimmt der ganze Vorgang nur

kurze Zeit in Anspruch. Wahrscheinlich hassen Sie es so wie wir, Ihre kostbare Freizeit damit zu vergeuden,

den Rasen zu mähen. Der Landroid

®

M wird sich als großartige Investition erweisen und Ihren Rasen viele

Jahre lang pﬂegen.

Sie können das Demo-Video zur Installation unter www.worxLandroid.com ansehen.

Der Landroid

®

M liebt das Mähen

Er ist zum häuﬁgen Mähen bestimmt – er hält Ihren Rasen gesund und dieser wird gepﬂegter aussehen als je

zuvor. Je nach Größe des Rasens kann der Landroid

®

M so programmiert werden, dass er zu jeder beliebigen Zeit

und mit jeder beliebigen Frequenz uneingeschränkt arbeitet. Er ist dazu da, für Sie zu arbeiten.

Stránka sa načítava...

Worx WG546E.9 Používateľská príručka

Tento návod je vhodný aj pre

Worx WG546E.9 Používateľská príručka

v iných jazykoch

Súvisiace články

Ostatné dokumenty