Whirlpool AKR 400 ME Užívateľská príručka

Značka: Whirlpool

Model: AKR 400 ME

Kategória: Odsávače pár

Typ: Užívateľská príručka

5019 318 33155

INSTALACJA I ZASTOSOWANIE

Uwaga dotycząca instalacji: okap powinien być zaistalowany w odleglosci minimalnie 60 cm od

palników elektrycznych oraz 70 cm od palników gazowych, gazowo-olejowych i węglowych. Jeżeli w

instrukcjach instalacji kuchenki gazowej przewidziana została większa odległość, należy ją

zastosować.

Uwaga dotycząca instalacji: przed przystąpieniem do instalowania i użytkowania okapu przeczytać

uważnie poniższe instrukcje, rysunki znajdują się na pierwszych stronach. Wykonawca nie ponosi

żadnej odpowiedzialności za problemy, szkody lub pożar spowodowany przez urządzenie, a

wynikający z niezastosowania się do informacji zawartych w instrukcji obsługi.

INSTALACE A POUŽITÍ

Poznámka k instalaci: digestoř musí být instalovaná v minimální vzdálenosti 60 cm od elektrických

sporáků a 70 cm od sporáků na plyn, naftu nebo uhlí. Jestliže je v pokynech k instalaci plynového

spotřebiče určena větší vzdálenost, než je uvedená vzdálenost, je nutné ji dodržet.

Poznámka k instalaci a použití: před instalací nebo použitím si pozorně přečtěte tuto příručku,

obrázky se nacházejí na prvních stranách. Výrobce odmítá jakoukoli odpovědnost za případné potíže,

škody nebo požár způsobené spotřebičem a vzniklé nedodržením pokynů uvedených v této příručce.

INŠTALÁCIA A POUŽITIE

Poznámka pri inštalácii: odsávač pár musí byt’ nainštalovaný v minimálnej vzdialenosti 60 cm od

elektrických sporákov a 70 cm od plynových a naftových sporákov alebo sporákov na uhlie. Ak pokyny

na inštaláciu plynovej varnej dosky určujú väčšiu vzdialenost’ ako je uvedená, dodržiavajte ich.

Poznámka pri inštalácii a používaní: pred inštaláciou alebo používaním odsávača pár si pozorne

prečítajte tento návod, nákresy nájdete na prvých stranách. Odmieta sa akákoľvek zodpovednost’ za

prípadné problémy, škody alebo požiare spôsobené spotrebičom, vyplývajúce z nedodržania pokynov

uvedených v tomto návode.

ÜZEMBE HELYEZÉS ÉS HASZNÁLAT

Üzembehelyezési figyelmeztetés: a készülék aljának elektromos tűzhely esetén legalább 60 cm,

gáz-, gázolaj- vagy szénüzemű tűzhely esetén pedig legalább 70 cm távolságban kell lennie a

főzőlaptól. Amennyiben a gáztűzhely üzembe helyezési útmutatója nagyobb távolságot ír elő, úgy azt

kell betartani.

Üzembehelyezési és használati figyelmeztetés: a készülék üzembe helyezése és használata előtt

olvassa el figyelmesen ezt a füzetet, amelynek első oldalain találja az ábrákat. A gyártó semmilyen

felelősséget nem vállal a készülékben esetlegesen keletkező azon meghibásodásokért, sérülésekért

vagy tüzekért, amelyeket a jelen füzetben foglalt utasítások be nem tartása okoz.

31833155.fm Page 1 Friday, April 22, 2005 5:37 PM

5019 318 33155

УСТАНОВКА И ЭКСПЛУАТАЦИЯ

Примечание по установке: вытяжка должна быть установлена на расстоянии не менее 60

см от электрических конфорок и 70 см от горелок, работающих на газе, дизельном топливе

или угле. Если инструкцией по установке газовой плиты предусмотрено большее по

сравнению с вышеуказанным расстояние, это требование подлежит выполнению.

Примечание по установке и эксплуатации: перед тем, как приступать к установке или

эксплуатации вытяжки, внимательно прочитайте настоящее руководство; иллюстрации

находятся на его первых страницах. Фирма#изготовитель снимает с себя всякую

ответственность за какие#либо неудобства, ущерб или пожар, вызванные несоблюдением

указаний, приведенных в настоящем руководстве.

ИНСТАЛИРАНЕ И УПОТРЕБА

Бележка за инсталиране: аспираторът трябва да се инсталира на разстояние минимум

60 см от електрически печки и 70 см от печки на газ, нафта или въглища. Ако в

инструкциите на устройството за готвене на газ е указано по#голямо разстояние за тази

спецификация, трябва да се изпълнява това разстояние.

Бележка за инсталиране и употреба: преди да инсталирате или използвате аспиратора,

прочетете внимателно това ръководство # фигурите се намират на първите страници. Не се

поема никаква отговорност за евентуални неудобства, повреди или пожари, предизвикани

от уреда, произтичащи от неспазването на инструкциите, дадени в това ръководство.

INSTALAREA ȘI UTILIZAREA

Notă privind instalarea: hota trebuie instalată la o distanţă minimă de 60 cm faţă de arzătoarele

electrice și de 70 cm faţă de arzătoarele pe bază de gaze, petrol sau cărbune. Dacă instrucţiunile de

instalare ale mașinii de gătit cu gaz specifică o distanţă mai mare decât cea indicată, trebuie să ţineţi

cont de ea.

Notă privind instalarea și utilizarea: înainte de a instala sau utiliza hota, citiţi cu atenţie acest manual,

desenele se găsesc pe primele pagini. Fabricantul își declină orice responsabilitate pentru eventualele

inconveniente, pagube sau incendii provocate aparatului, cauzate de nerespectarea instrucţiunilor din

acest manual.

INSTALLATION AND USE

For installation: the hood must be installed at least 60 cm from electric cookers and 70 cm from gas, gas oil or

coal cookers. If the installation instructions for a gas cooker specify a greater distance, then this distance must be

observed.

For installation and use: before installing or using the hood, read this manual carefully. The drawings are found

at the front of the manual. The manufacturer declines all liability for any faults, damage or fires caused by the

appliance as a result of failure to observe the instructions and recommendations given in this manual.

RUS

31833155.fm Page 2 Friday, April 22, 2005 5:37 PM

5019 318 33155

* jedynie w niektórych wersjach

* pouze u některých modelů

* iba pre niektoré modely

* csak egyes típusoknál

* только на некоторых моделях

* само за някои модели

* doar la unele modele

* only present on some models

31833155.fm Page 3 Friday, April 22, 2005 5:37 PM

5019 318 33155

V3a

Filtr tłuszczu

Tukový filtr

Tukový filter

Zsírszűrő

Жироулавливающий фильтр

Филтър за мазнини

Filtru pentru grăsime

Grease filter

Filtr węglowy

Uhlíkový filtr

Uhlíkový filter

Szénszűrő

Угольный фильтр

Въгленов филтър

Filtru pe bază de carbon

Carbon filter

31833155.fm Page 4 Friday, April 22, 2005 5:37 PM

5019 318 33155

Extractor hood installation (A): fumes are extracted and expelled to the outside through an exhaust duct fixed to the flange

C (bayonet coupling). Always shut off the unused exhaust outlet with the plug D1 provided (if provided- bayonet coupling).

Exhaust air must not be conveyed through a flue used for removal of fumes produced by gas combustion appliances or other

combustible materials, but must have an independent outlet. All national regulations governing extraction of fumes must be

observed.

Important! In some models, in order to use the rear exhaust outlet B2 the plastic part D2 or D3 must be removed first. Use

pliers and a cutter to remove it.

Filter version installation (F): If it is not possible to duct fumes and steam to the outside, the hood can be used in the filter

version by fitting a carbon filter/s (not supplied). In this way, fumes and steam are recycled through the front grille section

positioned above the control panel.

Check the position of the extraction/filter selector (inside the hood) G.

Fixing to the wall - Place the hood against the wall (or use the template H, if provided) and, using a pencil, mark the holes

(3 or 4 Ø 8mm holes), drill them, insert the rawlplugs J in the holes and 2 screws K in the top holes. Remove the grille and hang

the hood on the 2 screws. Next, from inside, insert the third (and fourth) screws L and screw them all down.

Fixing to the wall unit - Position the hood (or use the template H, if provided) and, using a pencil, mark the 4 Ø 6 mm holes

to be drilled on the bottom of the wall unit.

Fix the hood in place with 4 screws M from inside the wall unit.

Control panel

Light: move the switch to the right or press the next button to switch on.

Extraction speed: move the switch to the right or press the next button to increase extraction speed.

Grease filter - can be one of the following types:

Paper filter: must be replaced once a month or, if the top side is coloured, when the colour shows through the holes in the

grille.

Metal filter: must be washed once a month by hand or in a dishwasher, using a quick wash cycle with a low temperature.

To access the grease filter open the grille using the spring release catches E1 or E2 or E3 and release it from the retainers R1

or R2.

The self-supporting metallic filter has no support grille. To remove it, pull the spring release handlesE1 backwards and

remove the filter downwards.

Warning! Over time, the metallic filtermay become opaque; this in no way affects its filtering capacity.

Carbon filter - can be one of the following types:

Shaped V1: Remove the cover W by turning the knobs O through 90°.

Insert the carbon filter inside the special housing and secure it in place by turning the knob O

through 90°, then close the cover.

Replace every 4 months.

Rectangular V2: insert the rear edge first T and then the front (U) - replace every 6 months.

Circular V3: Bayonet coupling. Position the filter in the centre so that it covers the motor-protection grille, make sure that

the reference mark X1 or X2 or X3 on the carbon filter is aligned with the the reference mark Y on the fan shroud, then turn

clockwise; to remove, turn anti-clockwise, if provided with a tab Z remember to lift it up slightly first. Replace every 4

months.

Replacing the bulb/s - Remove the filters then remove the burnt-out bulb (E14 incandescent bulb, 40 W max). Refit the

filters.

G4 halogen bulb, 20 W max: use a small screwdriver or similar suitable tool to prise off.

Replace the bulb cover so that it clicks into position.

Cleaning the hood

Warning! Failure to remove oil and grease at least once a month could lead to fire.

Use a soft cloth damped in a neutral detergent. Never use abrasives or alcohol.

Before using the hood

Please read these instructions carefully in order to get the best out of your new hood.

Packaging materials can be dangerous for children. Keep packaging materials (plastic bags, polystyrene, etc.) well out of their

reach.

Make sure the hood has not been damaged during transport. Installation, electrical connections and replacement of the mains

lead with a plug or new flexible cable must be carried out by a qualified technician in compliance with local safety regulations.

PL SK H

RUS

BG RO

31833155.fm Page 19 Friday, April 22, 2005 5:37 PM

5019 318 33155

SAFEGUARDING THE ENVIRONMENT

1. Packaging

Packaging materials are 100% recyclable and are marked

with the recycling symbol . Dispose of packaging materials

in compliance with local waste disposal regulations. Packaging

materials can be dangerous for children. Keep packaging

materials (plastic bags, polystyrene, etc.) well out of their

reach.

2. Appliance

The appliance itself is made from recyclable materials.

Dispose of it in accordance with local waste disposal

regulations. Cut off the mains lead to render the appliance

unusable before disposing of it. The appliance must be

delivered to an authorised collection centre for scrapping.

PRECAUTIONS AND GENERAL

RECOMMENDATIONS

WARNING!

• Do not allow children or infirm persons to operate

the appliance without supervision.

• Make sure that children do not play with the

appliance.

1. Do not connect the appliance to the mains electricity

supply until installation is completed. Always disconnect

the hood from the mains before performing any cleaning

or maintenance.

2. Do not flambé food under the hood. Naked flames could

cause fire.

3. Do not leave pans unattended when frying. Cooking oil

can catch fire.

4. Regular cleaning and maintenance is essential to correct

functioning and good performance. Regularly remove dirt

deposits. Regularly clean or replace filters. Never use

flammable materials to convey exhaust air.

5. If the hood is used together with non-electrically powered

appliances, ambient negative pressure must not exceed

4Pa (4 x 10

-5

bars). Make sure that the room is

adequately ventilated.

Electrical connections

Before connecting the hood to the mains, make sure that the

voltage specified on the data plate corresponds to the voltage

in your home. The data plate is located inside the hood

behind the grease filter.

If the appliance is fitted with a power supply cable and plug,

the plug must be inserted in an accessible socket.

If the hood does not come pre-fitted with a mains plug, fit

one that conforms to applicable standards or use a double-

pole switch with a minimum breaking gap of 3 mm.

Replacement of the power supply cable with power plug or

flexible cable may only be carried out by an authorized

Service Centre or a qualified electrician.

Declaration of conformity

This product has been designed, manufactured and sold in

compliance with the following standards:

- safety objectives of the “Low Voltage”

Directive 73/23/EEC

- protection requirements of “EMC” Directive

89/336/EEC amended by Directive 93/68/EEC.

Trouble-shooting guide

Hood does not work:

• Is the power plug properly inserted in the mains socket?

• Is there a power failure?

• Is the mains fuse OK?

The hood is not extracting efficiently:

• Is the right extraction speed selected?

• Do the filters need to be cleaned or replaced?

• Are the air outlets blocked?

Light does not work:

• Does the bulb need to be replaced?

• Is the bulb correctly fitted?

• Is the mains fuse OK?

AFTER-SALES SERVICE

Before calling Technical Assistance

1. Check to see if you can fix the problem yourself

1. (see ”Trouble-shooting guide”).

2. Switch the hood off for a few minutes then switch it back

on and see if the problem has gone.

3. If the problem persists, call Technical Assistance.

Specify:

• the nature of the problem,

• the model of hood, stated on the data plate inside the

hood, accessible by removing the grease filters.

• your full address,

• your telephone number and area code.

• the service code (the number appearing below the word

SERVICE on the data plate inside the hood behind the

grease filter).

If any repairs are needed, contact an authorised Service

Centre (to ensure that only original spare parts are used and

that repairs are made correctly).

Failure to comply with these instructions may compromise

the safety and quality of the product.

PL SK H

RUS

BG RO

31833155.fm Page 20 Friday, April 22, 2005 5:37 PM

Whirlpool AKR 400 ME Užívateľská príručka

Značka: Whirlpool

Model: AKR 400 ME

Kategória: Odsávače pár

Typ: Užívateľská príručka

Stiahnite si PDF

správa

V iných jazykoch

English: Whirlpool AKR 400 ME User guide
polski: Whirlpool AKR 400 ME instrukcja
română: Whirlpool AKR 400 ME Manualul utilizatorului

Whirlpool AKR 400 ME Užívateľská príručka

Whirlpool AKR 400 ME Užívateľská príručka

V iných jazykoch

Súvisiace články