Renishaw RSP3 Installation & User's Guide

RSP3 installation and user's guide

Document part number H-1000-5124-03-A

RSP3 installation and user's guide

www.renishaw.com

Issued 03 2021

1

General information

This document may not be copied or reproduced in whole or in part, or transferred to any other media or language by any means, without the

prior written permission of Renishaw.

Disclaimer

WHILE CONSIDERABLE EFFORT WAS MADE TO VERIFY THE ACCURACY OF THIS DOCUMENT AT PUBLICATION, ALL WARRANTIES,

CONDITIONS, REPRESENTATIONS AND LIABILITY, HOWSOEVER ARISING, ARE EXCLUDED TO THE EXTENT PERMITTED BY LAW.

RENISHAW RESERVES THE RIGHT TO MAKE CHANGES TO THIS DOCUMENT AND TO THE EQUIPMENT, AND/OR SOFTWARE AND THE

SPECIFICATION DESCRIBED HEREIN WITHOUT OBLIGATION TO PROVIDE NOTICE OF SUCH CHANGES.

Trade marks

RENISHAW

®

, the probe symbol and REVO

®

are registered trade marks of Renishaw plc.

Renishaw product names, designations and the mark ‘apply innovation' are trade marks of Renishaw plc or its subsidiaries.

Other brand, product or company names are trade marks of their respective owners.

WEEE

The use of this symbol on Renishaw products and / or accompanying documentation indicates that the product should not be mixed with

general household waste upon disposal. It is the responsibility of the end user to dispose of this product at a designated collection point for

waste electrical and electronic equipment (WEEE) to enable reuse or recycling. Correct disposal of this product will help to save valuable

resources and prevent potential negative effects on the environment. For more information, please contact your local waste disposal service

or Renishaw distributor.

Warranty

Unless you and Renishaw have agreed and signed a separate written agreement, the equipment and/or software are sold subject to the

Renishaw Standard Terms and Conditions supplied with such equipment and/or software, or available on request from your local Renishaw

office.

Renishaw warrants its equipment and software for a limited period (as set out in the Standard Terms and Conditions), provided that they are

installed and used exactly as defined in associated Renishaw documentation. You should consult these Standard Terms and Conditions to find

out the full details of your warranty.

Equipment and/or software purchased by you from a third-party supplier is subject to separate terms and conditions supplied with such

equipment and/or software. You should contact your third-party supplier for details.

RSP3 installation and user's guide

www.renishaw.com

Issued 03 2021

2

Care of equipment

Renishaw probes and associated systems are precision tools used for obtaining precise measurements and must therefore be treated with

care.

Changes to Renishaw products

Renishaw reserves the right to improve, change or modify its hardware or software without incurring any obligations to make changes to

Renishaw equipment previously sold.

Company registration details

Renishaw plc. Registered in England and Wales. Company no: 1106260. Registered office: New Mills, Wotton-under-Edge, Gloucestershire,

GL12 8JR, UK.

Packaging

To aid end user recycling and disposal the materials used in the different components of the packaging are stated here:

Packaging component Material 94/62/EC code 94/62/EC number

Box Polypropylene PP 05

Packing foam Polyurethane foam PUR 113

Outer box Corrugated fibreboard PAP 20

Packaging insert Corrugated fibreboard PAP 20

Bag Static dissipative coating,

polyester, aluminium shield,

static dissipative polyethylene

C/LDPE 90

Bag Low density polyethylene LDPE 4

Label Polypropylene PP 05

CAUTION: If it is necessary to return any part of the system please ensure it is packaged carefully. Failure to do so could result in

transit damage for which the customer would be liable. Products supplied in plastic boxes must be returned in the original

packaging.

RSP3 installation and user's guide

www.renishaw.com

Issued 03 2021

3

Patents

Features of the RSP3 system and associated products (such as REVO-2), equipment and techniques are the subjects of one or more of the

following patents and patent applications:

CA2925301 CN100453970 EP1086352 IN259801 JP2016-533484 US2016-0238373

CN101166951 EP1086354 IN279118 JP2018-514773 US2018-0058884

CN101166953 EP1368615 IN292511 JP4062515 US6633051

CN101405563 EP1505362 IN294476 JP4695762 US6909983

CN101405564 EP1687589 IN295786 JP4726303 US7146741

CN101490430 EP1877727 IN296310 JP5196356 US7533574

CN101675317 EP1877732 WO2006/114603 JP5210536 US7809523

CN101772690 EP1989504 WO2007/107776 JP5350216 US7861430

CN102305613 EP2002206 WO2008/132490 JP5425476 US7885777

CN102906533 EP2002207 WO2011/135282 JP5555159 US7971365

CN103842766 EP2035719 WO2014/191729 JP5653581 US8006398

CN105408723 EP2140318 WO2015/049341 JP5658863 US8186882

CN105793695 EP2142880 WO2018/091867 JP5706158 US8302321

CN107532930 EP2167911 JP5851969 US8381588

EP2431707 JP6013533 US8425119

EP2564151 JP6199870 US8474148

EP2764324 JP6348577 US8511898

EP3004797 US8601701

EP3052926 US8756973

EP3289314 US8978261

US9038282

US9366519

US9903713

RSP3 installation and user's guide

www.renishaw.com

Issued 03 2021

4

Product compliance

EU declaration of conformity

Contact Renishaw plc or visit www.renishaw.com/EUCMM for the full EU declaration.

UK declaration of conformity

Contact Renishaw plc or visit www.renishaw.com/UKCMM for the full UK declaration.

EMC conformity

This equipment must be installed and used in accordance with this installation guide. This product is intended for industrial use only and

should not be used in a residential area or connected to a low voltage power supply network which supplies buildings used for residential

purposes.

FCC (USA only)

Information to user (47 CFR 15.105)

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These

limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to

cause harmful interference, in which case you will be required to correct the interference at your own expense.

Information to user (47 CFR 15.21)

The user is cautioned that any changes or modifications not expressly approved by Renishaw plc or authorised representative could void the

user's authority to operate the equipment.

Equipment label (47 CFR 15.19)

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation.

RSP3 installation and user's guide

www.renishaw.com

Issued 03 2021

5

ICES-001 (Canada only)

This ISM device complies with Canadian ICES-001.

Cet appareil ISM est conforme à la norme ICES‐001 du Canada.

REACH regulation

Information required by Article 33﴾1﴿ of Regulation ﴾EC﴿ No. 1907/2006 ﴾“REACH”﴿ relating to products containing substances of very high

concern (SVHCs) is available at:

www.renishaw.com/REACH

China RoHS

Contact Renishaw plc or visit www.renishaw.com/ChinaRoHSCMM for the full China RoHS tabulation.

RSP3 installation and user's guide

www.renishaw.com

Issued 03 2021

6

Safety

CAUTION: Before unpacking and installing the REVO system, the user should carefully read the safety instructions below and

ensure that they are followed at all times by all operators.

The RSP3 range of probes is only to be used with the Renishaw REVO head.

Operators must be trained in the use and application of the REVO system and accompanying products, in the context of the

machine it is fitted to, before being allowed to operate that machine.

Permanent magnets are used in some components of the REVO system and associated products. It is important to keep them away

from items which may be affected by magnetic fields, e.g. data storage systems, pacemakers and watches etc.

RSP3 LED emissions

The RSP3 range of scanning probes incorporate embedded high power LED sources and should not be used in the event of serious damage

to, or rupture of, any part of the RSP3. In such cases IMMEDIATELY disconnect the power source, remove and do not attempt to re-use the

parts. Contact your supplier for advice.

RCP TC-2 and RCP TC-3

The method of interrupting power is to disconnect the power cable or turn off the supply.

RSP3 installation and user's guide

www.renishaw.com

Issued 03 2021

7

Warnings

Beware of unexpected movement. The user should remain outside of the full working envelope of probe head and stylus. The

machine supplier should ensure the user is aware of the full working envelope of the system.

In all applications involving the use of machine tools or CMMs, eye protection is recommended.

It is the machine supplier's responsibility to ensure that the user is made aware of any hazards involved in operation, including those

mentioned in Renishaw product documentation, and to ensure that adequate guards and safety interlocks are provided.

Refer to the machine supplier's operating instructions.

The system components contain no user serviceable parts, with the exception of RCP TC-2, RCP TC-3, RCP2 and FCR25. No attempt should be

made to disassemble any part of the product. In the event of a problem please contact your supplier for assistance.

Under certain circumstances the probe signal may falsely indicate a probe-seated condition. Do not rely on probe signals to stop machine

movement.

Probe trigger override will prevent machine backing off in the event of a probe collision.

The probe joints are designed to release the probe and / or the stylus holder in the event of a crash.

This equipment is not suitable for use in a potentially explosive atmosphere.

Pinch hazards exist between parts. Do not hold the probe or probe head during movements.

It is essential for continued safety that all fuses are replaced by the correct type and rating.

REVO must be transported in Renishaw supplied packaging.

The cables must meet Renishaw specifications. Incorrect cabling could cause damage to the equipment.

RSP3 installation and user's guide

www.renishaw.com

Issued 03 2021

8

International safety instructions

BG ‐ ПРЕДУПРЕЖДЕНИЕ

Моля, обърнете на приложение 1 и прочетете инструкциите за безопасност на вашия собствен език, преди за разопаковате и

монтирате този продукт.

CZ ‐ VÝSTRAHA

Před rozbalením a instalací tohoto výrobku si přečtěte bezpečnostní pokyny ve vlastním jazyce uvedené v příloze 1.

DA - ADVARSEL

Læs sikkerhedsinstrukserne i Appendix 1 FØR udpakning og installation af dette produkt.

DE - WARNHINWEIS

Bevor Sie dieses Produkt auspacken und installieren, konsultieren Sie bitte Anhang 1 und lesen Sie die Sicherheitshinweise in Ihrer Sprache.

EL ‐ ΠΡΟΕΙΔΟΠΟΙΗΣΗ

Γυρίστε στο Κεφάλαιο 1 και διαβάστε τις οδηγίες ασφαλείας στη δική σας γλώσσα προτού ανοίξετε αυτό το προϊόν για να το

εγκαταστήσετε.

EN - WARNING

Before unpacking and installing this product, please consult Appendix 1 and read the safety instructions in your language.

ES - ADVERTENCIA

Consulte el apéndice 1 y lea las instrucciones de seguridad en su idioma antes de desempaquetar e instalar este producto.

ET - HOIATUS

Palun vaadake 1. lisa ning lugege enne selle toote lahtipakkimist ja paigaldamist ohutusjuhend läbi.

FI - VAROITUKSIA

Lue liitteessä 1 olevat omalla kielelläsi kirjoitetut turvaohjeet ennen tämän tuotteen pakkauksen avaamista ja asentamista.

FR - AVERTISSEMENT

Consulter l'annexe 1 et les instructions de sécurité dans votre propre langue avant de déballer et d'installer ce produit.

RSP3 installation and user's guide

www.renishaw.com

Issued 03 2021

9

GA - RABHADH

Téigh chuig aguisín 1 agus déan na treoracha sábháilteachta a léamh i do theanga féin le do thoil sula ndéantar an táirge seo a dhíphacáil

agus a shuiteáil.

HR - NAPOMENA

Prije nego što proizvod izvadite iz ambalaže i ugradite ga, otvorite Prilog 1 i pročitajte sigurnosne upute na svom jeziku.

HU – FIGYELMEZTETÉS

A termék kicsomagolása és telepítése előtt olvassa el az 1. számú függelékben található, az Ön anyanyelvén hozzáférhető biztonsági

utasításokat.

IT - AVVISO

Prima di aprire ed installare questo prodotto, leggere le istruzioni di sicurezza nella vostra lingua riportate nell'Appendice 1.

JA ‐ 警告

この製品を箱から取り出し設置する前に、付録 1 に記載された安全性に関する注意書きをお読みください。

LT – ĮSPĖJIMAS

Prieš išpakuodami ir įdiegdami produktą, turite grįžti prie 1 priedo ir perskaityti nurodymus dėl saugos savo kalba.

LV – BRĪDINĀJUMS

Pirms šī izstrādājuma izsaiņošanas un uzstādīšanas izskatiet 1. pielikumā sniegtās drošības instrukcijas savā valodā.

MT - TWISSIJA

Jekk jogħġbok mur f'appendiċi 1 u aqra l‐istruzzjonijiet tas‐sigurtà fil‐lingwa tiegħek qabel ma toħroġ dan il‐prodott mill‐ippakkjar u

tinstallah.

NL - WAARSCHUWING

Ga naar appendix 1 en lees de veiligheidsinstructies in uw eigen taal, voordat u dit product uitpakt en installeert.

PL ‐ OSTRZEŻENIE

Przed rozpakowaniem i zainstalowaniem tego produktu prosimy o zapoznanie się z Dodatkiem 1 i przeczytanie zaleceń dotyczących

bezpieczeństwa w danym języku.

PT ‐ ADVERTÊNCIA

Você deve retornar ao Anexo 1 e ler as instruções de segurança em seu idioma antes de desembalar e instalar este produto.

RSP3 installation and user's guide

www.renishaw.com

Issued 03 2021

10

RO - AVERTISMENT

Înainte de a desface ambalajul şi a instala acest produs, vă rugăm să căutaţi Anexa 1 şi să citiţi cu atenţie instrucţiunile de siguranță, în limba

română.

SK ‐ VÝSTRAHA

Pred rozbalením a inštaláciou tohto produktu si pozrite prílohu 1 a prečítajte si bezpečnostné pokyny vo vašom jazyku.

SL - OPOZORILO

Preden izdelek vzamete iz embalaže in ga vgradite, odprite Prilogo 1 in preberite varnostna navodila v svojem jeziku.

SV - VARNING

Gå till bilaga 1 och läs säkerhetsinstruktionerna på ditt eget språk innan du packar upp och installerar denna produkt.

TW ‐ 警告

在拆開和安裝本產品之前，請翻頁至附錄 1 閱讀母語的安全指示。

中文 — 警告

在拆包和安装本产品之前，请翻到附录1，阅读中文版安全说明。

RSP3 installation and user's guide

www.renishaw.com

Issued 03 2021

11

References and associated documents

The following Renishaw documents are referred to in this document or may be a source of further relevant information. They can easily be

acquired from Renishaw web site www.renishaw.com.

Title Document number

User's guide: REVO-2 H-1000-7590

Installation and user's guide: RSP3 H-1000-5124

Installation and user's guide: SFP2 surface finish probe H-1000-5365

User's guide: RVP H-1000-3322

Installation and user's guide: MRS modular rack system H-1000-5088

Installation guide: MRS2 modular rack system H-1000-5255

Technical specifications guide: Styli and accessories H-1000-3200

RSP3 installation and user's guide

www.renishaw.com

Issued 03 2021

12

System description

The RSP3 range of probes gives REVO users the ability to carry cranked stylus arrangements and enhanced capability for carrying long styli.

The RSP3-1 / 2 / 3 / 4 probes can be used for both 3D-scanning (X, Y, Z) and touch-trigger applications. They enable accurate scanning

measurement with effective stylus lengths ranging from 20 mm - 394 mm. The RSP3-6 probe, on the other hand, provides REVO with

enhanced capability for carrying long cranked and straight styli. RSP3-6 can be used for 2D scanning and 3D touch-trigger applications. It

carries straight extensions up to 800 mm from REVO's A-axis centre of rotation, and cranked extensions up to 600 mm from REVO's A-axis

centre of rotation.

The RSP3 range uses 3-axis scanning with fixed REVO head angles during measurement. Each probe is designed to provide optimized

accuracy and contact force over a specified stylus range. Consequently, the RSH3 stylus holders are intended to fit only with their respective

RSP3 probe.

Design principles of the RSP3 scanning probes

RSP3 uses an optical transducer sensor and a pivoting motion system similar to that found in SP25M system.

The probe's pivoting motion system has two diaphragm springs. One of the RSP3 springs allows movement in all directions whilst the other

(pivot) spring is stiff in (probe) X and Y, but allows movement in Z. Its optical transducer sensor system has two infrared light emitting diodes

that project invisible infrared beams on mirrors mounted on the pivoting moving structure within the probe. The mirrors focus the beams

back onto two position sensitive devices (PSDs) which provide signal outputs in the three probe axes: P, Q, R (converted into X, Y, Z signals by

the calibration routine).

Unlike the SP25M, the RSP3's probe and module elements are built as one.

System components overview

RSP3-1 / 2 / 3 / 4

The RSP3-1 / 2 / 3 / 4 range of probes provide REVO with 3D-scanning (X, Y, Z) touch-trigger and crank stylus capabilities.

RSP3-6

The RSP3-6 probe provides REVO with enhanced capability for carrying long cranked and straight styli. RSP3-6 can be used for both 3D

touch-trigger and 2D scanning applications.

RSH3-1 / 2 / 3 / 4 stylus holders

The RSH3-1 / 2 / 3 / 4 stylus holders are designed to fit with their respective RSP3 probe. They enable accurate scanning measurements with

effective stylus lengths ranging from 20 mm - 394 mm.

The RSH3 range of stylus holders replace the SH25 range of stylus holders for use with REVO only. The SH25 range should still be used with

SP25M.

RSP3 installation and user's guide

www.renishaw.com

Issued 03 2021

13

RSH3-6c-500 / 600 and RSH3-6-600 / 700 / 800 stylus holders

The RSH3-6 stylus holders for the RSP3-6 probe are suitable for applications requiring straight extensions up to 800 mm from REVO's A-axis

centre of rotation. The RSH3-6c stylus holders are suitable for applications requiring cranked extensions up to 600 mm from REVO's A-axis

centre of rotation.

RCP TC-2 and RCP TC-3

The thermally controlled RCP TC-2 and RCP TC-3 ports maintain stored probes at operating temperature. They are compatible with

Renishaw's MRS and MRS2 rack systems.

NOTE: RCP TC-3 is for use with RSP3-6 and SFP2 only.

RCP2

The RCP2 enables rapid and repeatable changing of RSH3-6 stylus holders. It is compatible with Renishaw's MRS and MRS2 rack systems.

FCR25 flexible change rack unit

Rapid and repeatable changing of the RSH3-1 / 2 / 3 / 4 stylus holders is possible via the FCR25 triple port change rack unit, which is

compatible with Renishaw's MRS and MRS2 rack systems.

FCR25 stand-off plate

The FCR25 stand-off plate should be used on all REVO installations to mount FCR25 ports to the MRS / MRS2 rack system.

PA25-RSH3 port adapter

PA25-RSH3 port adapters are required for automated changing of the RSH3-1 / 2 / 3 / 4 stylus holders into and out of the FCR25 rack. A

PA25-RSH3 port adapter is included in every RSH3 and RSP3 kit.

RSP3 installation and user's guide

www.renishaw.com

Issued 03 2021

14

RSP3 probes and stylus holders

RSP3 installation and user's guide

www.renishaw.com

Issued 03 2021

15

Environmental and electrical specifications

Environmental specification

Operating temperature range 20 °C ±2 °C

Storage temperature range ‐10 °C to +70 °C ﴾14 °F to 158 °F﴿

Operating humidity 0% to 80% (non-condensing)

Storage humidity 0% to 80% (non-condensing)

Electrical specification

The REVO-2 head, and probe electronics and motors, are powered from the UCC S5.

The RCP TC-2 and RCP TC-3 are powered by a separate power supply that is supplied by Renishaw.

No other additional power supplies are required.

RSP3 installation and user's guide

www.renishaw.com

Issued 03 2021

16

RSP3 range dimensions

NOTE: Dimensions are to the kinematic planes.

All dimensions are in mm.

RSP3 installation and user's guide

www.renishaw.com

Issued 03 2021

17

RSP3 range specifications

RSP3 installation and user's guide

www.renishaw.com

Issued 03 2021

18

RSP3-1 / 2 / 3 / 4

Characteristic Requirements

Probe attributes Scanning with 3-axis measurement (X, Y, Z) and 3-axis touch-trigger

Measurement range ±0.5 mm deflection in all directions in all orientations

Overtravel range

X, Y 2 mm

+Z 1.7 mm

-Z 1.2 mm

Resolution Capable of <0.1 μm

Spring rate Nominally 0.6 N/mm - when using shortest specified stylus

Nominally 0.2 N/mm - when using longest specified stylus

Weight

RSP3-1 86 g (3.03 oz) (excluding stylus holder and stylus)

RSP3-2 90 g (3.17 oz) (excluding stylus holder and stylus)

RSP3-3 94 g (3.32 oz) (excluding stylus holder and stylus)

RSP3-4 101 g (3.56 oz) (excluding stylus holder and stylus)

Effective stylus length range Always observe the specified stylus range for the scanning module

being used. Use Renishaw's M3 range of styli.

RSP3-1 + RSH3-1 EWL 20 mm - 50 mm (0.79 in - 1.97 in) using 20 mm - 50 mm stylus

RSP3-2 + RSH3-2 EWL 44 mm - 99 mm (1.73 in - 3.90 in) using 20 mm - 75 mm stylus

RSP3-3 + RSH3-3 EWL 114 mm - 194 mm (4.49 in - 7.64 in) using 20 mm - 100 mm

stylus

RSP3-4 + RSH3-4 EWL 214 mm - 394 mm (7.64 in - 15.51 in) using 20 mm - 200 mm

stylus

Mounting Magnetised kinematic coupling

Crash protection

±X, ±Y, ‐Z Via break out of probe or stylus holder

+Z Via integral bump-stop design

Signal outputs Non-linear and non-orthogonal analogue outputs - rate gain and

resolution are not fixed

Change rack options

RCP TC-2 Thermally controlled change port for probe changing only

This single port unit mounts on the MRS / MRS2 rack

FCR25 with FCR25 front spacer kit Triple port unit which mounts on the MRS / MRS2 rack

Interface options UCC S5

RSP3 installation and user's guide

www.renishaw.com

Issued 03 2021

19

RSP3-6

Characteristic Requirements

Probe attributes 2-axis scanning (X,Y) and 3-axis touch-trigger (X,Y,Z)

Measurement range ±0.5 mm deflection in all directions in all orientations

Overtravel range

X, Y 2 mm

+Z 1.7 mm

-Z 1.2 mm

Resolution Capable of <0.1 μm

Weight 300 g (10.58 oz) (excluding stylus holder and stylus)

Effective stylus length range

RSP3-6 + RSH3-6c-500 EWL 348 mm (13.70 in) using M2 star centre

RSP3-6 + RSH3-6c-600 EWL 448 mm (17.64 in) using M2 star centre

RSP3-6 + RSH3-6-600 EWL 456 mm (17.95 in) using 10 mm stylus

RSP3-6 + RSH3-6-700 EWL 556 mm (21.89 in) using 10 mm stylus

RSP3-6 + RSH3-6-800 EWL 656 mm (25.83 in) using 10 mm stylus

Mounting Magnetised kinematic coupling

Crash protection

±X, ±Y, ‐Z Via break out of probe or stylus holder

+Z Via integral bump-stop design

Change rack options

RCP TC-3 Thermally controlled change port for probe changing only

This single port unit mounts on the MRS / MRS2 rack

RCP2 For stylus holder changing only

This single port unit mounts to the MRS or MRS2

Interface options UCC S5

RSP3 installation and user's guide

www.renishaw.com

Issued 03 2021

20

Stránka sa načítava...

Renishaw RSP3 Installation & User's Guide

Renishaw RSP3 Installation & User's Guide

v iných jazykoch

Súvisiace články

Ostatné dokumenty