UNITED OFFICE ULGD 350 A1 Operating Instructions Manual

Značka: UNITED OFFICE

Model: ULGD 350 A1

Kategória: Laminátory

Typ: Operating Instructions Manual

Táto príručka je tiež vhodná pre

100158

IAN 100158

LAMINATOR ULGD 350 A1

LAMINATOR

Operating instructions

NAPRAVA ZA PLASTIFICIRANJE

Navodila za uporabo

LAMINÁLÓGÉP

Használati utasítás

URZĄDZENIE DO LAMINOWANIA

Instrukcja obsługi

PRÍSTROJ NA LAMINOVANIE

Návod na obsluhu

LAMINOVAČKA

Návod k obsluze

LAMINIERGERÄT

Bedienungsanleitung

GB Operating instructions Page 1

PL Instrukcja obsługi Strona 15

HU Használati utasítás Oldal 29

SI Navodila za uporabo Stran 43

CZ Návod k obsluze Strana 57

SK Návod na obsluhu Strana 71

DE / AT / CH Bedienungsanleitung Seite 85

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of

the device.

Przed przeczytaniem proszę rozłożyć stronę z ilustracjami, a następnie proszę zapoznać się z wszystkimi

funkcjami urządzenia.

Olvasás előtt kattintson az ábrát tartalmazó oldalra és végezetül ismerje meg a készülék mindegyik

funkcióját.

Pred branjem odprite stran s slikami in se nato seznanite z vsemi funkcijami naprave.

Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.

Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen

Funktionen des Gerätes vertraut.

ULGD 350 A1

Index

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Information for these operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Copyright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Limited liability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Warning symbols used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Basic Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Setting up and connecting to the power supply . . . . . . . . . . . . . . . . . . . . . 5

Items supplied and transport inspection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Disposal of the packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Requirements on the installation site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Appliance description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Handling and operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Suitable laminating pouches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Switching levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Preparing for hot lamination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Preparing for cold lamination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Lamination process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Anti-blocking function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Notes on the Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Importer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

IB_100158_ULGD350A1_LB4.indb 1 02.07.14 13:42

ULGD 350 A1

Introduction

Information for these operating instructions

Congratulations on the purchase of your new appliance.

You have clearly decided in favour of a quality product. These operating instructions

are a component of the Laminator ULGD 350 A1 (henceforth designated as the

appliance) and they supply you with important information on the intended use,

safety, installation and connection as well as operation of the appliance.

These operating instructions must be constantly kept available close to the appli-

ance. They are to be read and applied by everyone occupied with operating the

appliance and eliminating any malfunctions it may have.

Retain these operating instructions and pass them on, with the appliance, to any

future owners.

This documentation is copyright protected.

All reproductions or duplications, also as extracts, as well as representations

of the illustrations, even in an altered state, are only permitted with the written

approval of the manufacturer.

Limited liability

All technical information, data and instructions for installation, connection and

operation contained in this operating manual correspond to the latest available

at the time of printing and, to the best of our knowledge, take into account our

previous experience and know-how.

No claims can be derived from the details, illustrations and descriptions in these

instructions.

The manufacturer assumes no responsibility for damage caused by failure to observe

these instructions, improper use, incompetent repairs, making unauthorised modi-

ﬁ cations or for using unapproved replacement parts.

Intended use

This laminator is intended exclusively for use in domestic households, for the hot

and cold lamination of documents made from paper or cardboard. This appliance

is not intended for commercial or industrial use.

This appliance is not intended for any other use or for uses beyond those men-

tioned. Claims of any kind for damage resulting from unintended use will not

be accepted. The user alone bears liability.

IB_100158_ULGD350A1_LB4.indb 2 02.07.14 13:42

ULGD 350 A1

Warning symbols used

In these operating instructions the following warnings are used:

DANGER

A warning at this risk level indicates a threateningly dangerous

situation.

If the dangerous situation is not avoided, it could result in death or serious injury.

► Follow the instructions given in this warning to avoid the risk of death or

severe personal injury.

WARNING

A warning at this risk level indicates a possible dangerous

situation.

If the dangerous situation is not avoided it could lead to injuries.

► Follow the instructions given in this warning to avoid the risk of personal

injuries.

IMPORTANT

A warning at this risk level indicates possible property damage.

If the situation is not avoided it could lead to property damage.

► Follow the instructions in this warning to avoid property damage.

NOTICE

►

A notice indicates additional information that may assist you in the handling

of the appliance.

IB_100158_ULGD350A1_LB4.indb 3 02.07.14 13:42

ULGD 350 A1

Safety

In this chapter you receive important safety information regarding the handling

of the appliance. This appliance complies with the statutory safety regulations.

Incorrect usage can lead to personal injury and property damage.

Basic Safety Instructions

For safe handling of the appliance observe the following

safety information:

■ Before use check the appliance for visible external dam-

age. Do not put into operation an appliance that is dam-

aged. There will be a risk of a fatal electrical shock.

■ Repairs should only be carried out by authorised special-

ist companies or by the Customer Services department.

Incorrect repairs can result in signiﬁ cant risks for the user.

In addition, warranty claims become void.

■ To avoid risks, arrange for a defective power cable to be

replaced by qualiﬁ ed technicians or by our Customer

Service Department.

■ NEVER use the appliance with a defective power cable.

There will be a risk of a fatal electrical shock.

■ Do not use extension cables or power socket strips that

do not meet the required safety standards.

■ The mains power socket must be easily accessible, so that

the power cable can be easily and quickly disconnected

in the event of an emergency.

■ Do not use an external timing switch or a separate re-

mote control system to operate the appliance.

■ This appliance may be used by children aged 8 over

and by persons with reduced physical, sensory or mental

capabilities or lack of experience and knowledge, pro-

vided that they are under supervision or have been told

how to use of the appliance safely and are aware of the

potential risks. Children must not play with the appliance.

Cleaning and user maintenance tasks must not be carried

out by children unless they are supervised.

IB_100158_ULGD350A1_LB4.indb 4 02.07.14 13:42

ULGD 350 A1

■ Never perform hot lamination on ﬂ ammable, heat-

sensitive and/or meltable materials and do not laminate

drawings on temperature-sensitive paper or material that

will undergo changes in colour or quality when subjected

to heat.

■ Never laminate valuable or unique documents. Although

the appliance complies with all current safety norms/

standards, malfunctions can never be completely ruled

out. Malfunctions with the laminator can result in damage

to the document being laminated.

Setting up and connecting to the power supply

Items supplied and transport inspection

The appliance is delivered with the following components as standard:

▯ Laminator ULGD 350 A1

▯ Document support

▯ 10 x Laminating pouches DIN A4 for hot laminating (80 micron)

▯ 10 x Laminating pouches DIN A5 for hot laminating (80 micron)

▯ 10 x Laminating pouches for hot lamination of business cards (80 micron)

▯ This operating manual

NOTICE

►

Check the contents to make sure everything is present and for signs of visible

damage.

► If the contents are not complete or are damaged due to defective packaging

or through transportation, contact the Service Hotline (see chapter Service).

Unpacking

♦ Extract the appliance, the laminating pouches and the operating instructions

from the carton.

♦ Remove all packing material.

DANGER

►

Packaging material should not be used as a play thing by children. There is

a risk of suﬀ ocation!

IB_100158_ULGD350A1_LB4.indb 5 02.07.14 13:42

ULGD 350 A1

Disposal of the packaging

The packaging protects the appliance from transport damage. The packaging

materials are selected from the point of view of their environmental friendliness

and disposal technology and are therefore recyclable.

The recirculation of packaging into the material circuit saves on raw material and

reduces the amount of waste generated. Dispose of packaging material that is

no longer needed as per the regionally established regulations.

NOTICE

►

If possible preserve the appliance's original packaging during the warranty

period so that, in the event of a warranty claim, you can package the appli-

ance ideally for its return.

Requirements on the installation site

For safe and ﬂ awless operation of the appliance, the installation site must comply

with the following requirements:

■ When setting it up, place the appliance on a ﬁ rm, ﬂ at and horizontal surface.

■ Place the appliance so that at least 30 cm of space remains unoccupied

behind the laminator. Otherwise the laminating pouch cannot be completely

ejected from the laminator after lamination.

■ Do not operate the appliance in a hot, wet or very humid environment or

close to combustible material.

■ The mains power socket must be easily accessible, so that the power cable

can be easily disconnected in the event of an emergency.

Electrical connection

IMPORTANT

► Before you connect the appliance, compare the connection data (voltage

and frequency) on the data plate with that of your mains power network.

This data must match in order to avoid any damage to the appliance.

► Ensure that the power cable is undamaged and is not routed over hot

surfaces and/or sharp edges.

► Ensure that the power cable is not taut or kinked.

► Do not let the power cable hang over edges (trip wire eﬀ ect).

♦ Insert the plug into a mains power socket.

IB_100158_ULGD350A1_LB4.indb 6 02.07.14 13:42

ULGD 350 A1

Appliance description

Pouch ejector slot

Indicator light Ready (ready for use)

Indicator light Power (appliance switched on)

Anti-Blocking switch and pouch thickness switch

On/Oﬀ switch with selector switch for hot and cold lamination (Hot/Oﬀ /Cold)

Pouch slot for manual pouch insertion

Document support

Handling and operation

In this chapter you will receive important information about the handling and

operation of the appliance.

Suitable laminating pouches

For hot lamination you can use pouches with a width of up to 230 mm and a

maximum thickness of 125 micron. For cold lamination you can use pouches with

a maximum thickness of 200 microns. Please note that each laminating pouch

may only be used once.

NOTICE

►

For hot lamination, use only laminating pouches that are expressly

intended for hot lamination.

► For cold lamination, use only laminating pouches that are expressly

intended for cold lamination.

► Take note that the laminating pouches supplied with the laminator are

intended exclusively for hot lamination.

Switching levels

Selector switch

position

Pouch thickness

switch position

Laminating pouch

thickness

Hot 80 > 60 - 80

Hot 125 85 - 125

Cold 125 to 200

NOTICE

►

For high-gloss photos, you should select the switch position “125” as well

as the appropriate pouch thickness.

IB_100158_ULGD350A1_LB4.indb 7 02.07.14 13:42

ULGD 350 A1

Preparing for hot lamination

♦ Insert the document support into the two openings under the pouch ejector

slot , such that it is seated ﬁ rmly on the appliance.

♦ Insert the plug of the laminator into a mains power socket.

♦ Switch the appliance on by placing the selector switch for hot and cold

lamination

at "HOT". The red indicator light Power

glows.

♦ Place the pouch thickness switch

at the corresponding pouch thickness

(see also chapter Switching levels).

NOTICE

►

The attainment of the operating temperature is indicated by the glowing

of the green indicator light Ready

. For a more uniform laminating result

we recommend, especially for thinner foils (below 125 Micron), and after

adjustment to a diﬀ erent foil thickness, to ﬁ rst wait an additional 2-3 minutes

before beginning with lamination.

♦ Place the document to be laminated into a laminating pouch of the

appropriate size.

NOTICE

►

Ensure that all edges of the document have at least two millimetres of

space to the edges of the laminating pouch, as shown in Fig. 1.

► Ensure that you use only one pouch for laminating. First open it up, as

shown in Fig. 2.

► For further information about the lamination process, please read the

section Lamination process.

Fig. 1

Fig. 2

IB_100158_ULGD350A1_LB4.indb 8 02.07.14 13:42

ULGD 350 A1

Preparing for cold lamination

IMPORTANT

► After hot laminating, allow the laminator to cool down completely before

beginning with cold lamination. Bear in mind, the rollers inside the laminator

will still be hot. This could damage the laminating pouch and the document

to be laminated!

♦ If not already done: Insert the document support into the two openings

under the pouch ejector slot

, such that it is seated ﬁ rmly on the appliance.

♦ Insert the plug of the laminator into a mains power socket.

♦ Switch the appliance on by placing the selector switch for hot and cold lami-

nation

at "Cold". The red indicator light Power

and the green indicator

light Ready

glow.

♦ Place the pouch thickness switch

at the corresponding pouch thickness

(see also chapter Switching levels).

♦ Place the document to be laminated into a laminating pouch of the appropriate

size.

NOTICE

►

Ensure that all edges of the document have at least two millimetres of space

to the edges of the laminating pouch, as shown in Fig. 1 (see p. 8).

► Make certain that you use only one pouch for laminating. First open it up,

as shown in Fig. 2 (see p. 8).

► For further information about the lamination process, please read the section

Lamination process.

Lamination process

♦ Place the pouch centrally between the two A4 markings and with the closed

side towards the pouch slot

and on the supporting surface.

♦ Slide the pouch slowly and straightly into the pouch slot

♦ When you have slid the pouch several centimetres into the slot

it will then

be pulled in automatically. Release the laminating pouch as soon as you

notice it being pulled in automatically.

IMPORTANT

►

Ensure that there is at least 30 cm of free space behind the laminator.

Otherwise, the pouch will not be ejected completely from the laminator

after lamination. This could damage the pouch.

♦ The ﬁ nished and laminated pouch is ejected from the pouch ejector slot

of the laminator.

IB_100158_ULGD350A1_LB4.indb 9 02.07.14 13:42

ULGD 350 A1

NOTICE

►

Only after hot lamination: When the ﬁ nished laminated pouch is

ejected from the pouch ejector slot of the laminator, it is hot and can

easily change its shape. For this reason, let the laminated pouch cool for

one minute before touching it.

► To improve the lamination result, you can weigh a still hot laminated pouch

down with a book, a ﬁ le folder or any other heavy, ﬂ at object. This will

give it a smooth and ﬂ awless surface.

♦ If you do not wish to start another laminating procedure, move the On/

Oﬀ switch

to "Oﬀ " and rotate the pouch thickness switch

to the ABS

position.

♦ Disconnect the plug from the mains power socket.

Anti-blocking function

At the start of the lamination process, the pouch may be pulled in at an angle or

jam itself inside the appliance.

♦ Turn the anti-blocking switch

to the position ABS. The pouch will no longer

be drawn in.

♦ Remove the pouch and turn the anti-blocking switch

back to the desired

pouch thickness.

♦ Re-start the lamination process.

Cleaning

DANGER

Risk of potentially fatal electrical shock!

► Remove the plug from the mains power socket before beginning to clean

the appliance.

► Ensure that moisture cannot permeate into the appliance during cleaning.

IMPORTANT

Possible damage to the appliance.

► Do not use aggressive or abrasive cleaners as they may damage the surface

of the housing.

♦ Clean the housing of the appliance only with a lightly moistened cloth and

a mild detergent.

IB_100158_ULGD350A1_LB4.indb 10 02.07.14 13:42

ULGD 350 A1

Cleaning the inside of the appliance:

With every lamination, contaminants are deposited on the rollers inside the

laminator. Over time, this reduces the performance of the laminator.

You should therefore clean the rollers inside the laminator after use.

♦ Prepare the appliance for use, as described in the chapter Preparing for

hot lamination, until the green indicator light Ready

glows.

♦ Then guide a sheet of folded in the middle A4 paper (maximum thickness

1.0 mm), without a pouch and with the fold forward, slowly into the manual

pouch insertion slot

♦ Release the sheet as soon as you notice that it is being pulled in automatically.

The contaminants on the rollers inside the laminator now ﬁ rmly attach themselves

to the sheet of paper. The paper will be ejected from the pouch ejector slot

of the laminator.

♦ Repeat this cleaning process several times. Use a fresh clean sheet of paper

each time.

When you no longer see any contaminants on the paper, the rollers inside the

laminator are clean.

Storage

The appliance has a built-in cable winder on the underside of the housing, on

which you can wrap the power cable when it is not in use. This prevents the

power cable from being pinched, damaged or soiled, and it cannot become

a source of danger by hanging loosely down.

♦ Store the appliance in a clean, dry place away from direct sunlight.

Disposal

Do not dispose of the appliance into the normal household

waste. This product is subject to the provisions of the European

Directive 2012/19/EU WEEE (Waste Electrical and Electronic

Equipment).

Dispose of the appliance through an approved disposal centre or at your com-

munity waste facility. Pay heed to the currently applicable regulations. In case of

doubt, please contact your waste disposal centre.

IB_100158_ULGD350A1_LB4.indb 11 02.07.14 13:42

ULGD 350 A1

Appendix

Technical data

Operational voltage 220 - 240 V ∼, 50 Hz

Current consumption 1.6 A

Power consumption 350 W

Protection class

II/

Pouch width max. 230 mm

Pouch thickness for hot lamination max. 125 Micron

Pouch thickness for cold lamination max. 200 Micron

Lamination times

Sheet size

Pouch thickness switch

position: 80 Micron

Pouch thickness switch

position: 125 Micron

DIN A4 approx. 40 s approx. 51 s

DIN A5 approx. 29 s approx. 36 s

Overheating protection

This appliance is ﬁ tted with an overheating protector. If the motor overheats

due to overloading, the appliance switches itself oﬀ automatically. In this case,

disconnect the power cable and wait until the appliance has cooled down to

room temperature. You can then reconnect the power cable with a mains power

socket and take the appliance back into operation. We recommend that you let

the appliance cool down for about 30 minutes after 2 hours of operation.

Notes on the Declaration of Conformity

This appliance complies, in regards to conformance with

the basic requirements and other relevent regulations, with

the EMC Directive 2004/108/EC, as well as the Directive

for Low Voltage Devices 2006/95/EC.

The complete original Declaration of Conformity can be

obtained from the importer.

IB_100158_ULGD350A1_LB4.indb 12 02.07.14 13:42

ULGD 350 A1

Warranty

The warranty for this appliance is for 3 years from the date of purchase. The

appliance has been manufactured with care and meticulously examined before

delivery.

Please retain your receipt as proof of purchase. In the case of a warranty claim,

please make contact by telephone with our Customer Service Department. Only

in this way can a post-free despatch for your goods be assured.

NOTICE

►

The warranty covers only claims for material and manufacturing defects,

but not for transport damage, wearing parts or for damage to fragile com-

ponents, e.g. buttons or batteries.

This product is for domestic use only and is not intended for commercial use. The

warranty is void in the case of abusive and improper handling, use of force and

internal tampering not carried out by our authorised service branch.

Your statutory rights are not restricted in any way by this warranty. The warranty

period is not extended by repairs made under the warranty. This applies also to

replaced and repaired parts.

Damages and defects extant at the time of purchase must be reported immedi-

ately after unpacking, resp. no later than two days after the date of purchase.

Repairs made after the lapse of the warranty period are subject to charge.

Service

Service Great Britain

Tel.: 0871 5000 720 (£ 0.10/Min.)

E-Mail: k[email protected]

IAN 100158

Hotline availability: Monday to Friday 08:00 - 20:00 (CET)

Importer

KOMPERNASS HANDELS GMBH

BURGSTRASSE 21

44867 BOCHUM, GERMANY

www.kompernass.com

IB_100158_ULGD350A1_LB4.indb 13 02.07.14 13:42

ULGD 350 A1

IB_100158_ULGD350A1_LB4.indb 14 02.07.14 13:42

ULGD 350 A1

Spis treści

Wprowadzenie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Informacje o niniejszej instrukcji obsługi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Prawo autorskie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Ograniczenie odpowiedzialności . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Użytkowanie zgodne z przeznaczeniem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Zastosowane wskazówki ostrzegawcze . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Bezpieczeństwo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Podstawowe zasady bezpieczeństwa . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Ustawianie i podłączanie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Zakres dostawy i przegląd po rozpakowaniu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Rozpakowanie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Utylizacja opakowania . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Wymagania dotyczące miejsca ustawienia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Podłączenie elektryczne . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Opis urządzania . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Obsługa i praca . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Odpowiednie folie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Stopnie przełączania . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Przygotowanie do laminowania na gorąco . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Przygotowanie do laminowania na zimno . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Laminowanie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Funkcja zapobiegająca blokowaniu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Czyszczenie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Przechowywanie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Utylizacja . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Załącznik . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Dane techniczne . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Wskazówki dotyczące deklaracji zgodności . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Gwarancja . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Serwis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Importer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

IB_100158_ULGD350A1_LB4.indb 15 02.07.14 13:42

ULGD 350 A1

Wprowadzenie

Informacje o niniejszej instrukcji obsługi

Gratulujemy zakupu naszego urządzenia.

Wybrany produkt charakteryzuje się wysoką jakością. Niniejsza instrukcja obsługi

stanowi część laminatora ULGD 350 A1 (nazywanego dalej „urządzeniem”)

i przekazuje ważne wskazówki dotyczące użytkowania zgodnego z przezna-

czeniem, bezpieczeństwa, montażu i podłączania, a także obsługi urządzenia.

Instrukcję obsługi należy zawsze przechowywać w pobliżu urządzenia. Musi ją

przeczytać, a także jej przestrzegać każdy, kto podejmuje się obsługi urządzenia

i usuwania usterek w urządzeniu.

Zachowaj tę instrukcję obsługi, a przy odsprzedaży urządzenia przekaż ją wraz

z urządzeniem nowemu właścicielowi.

Prawo autorskie

Niniejsza dokumentacja jest chroniona prawem autorskim.

Wszelkie rozpowszechnianie, wzgl. każdy przedruk, także we fragmentach,

jak również odtwarzanie ilustracji, także w zmienionym stanie, jest dozwolone

wyłącznie za pisemną zgodą producenta.

Ograniczenie odpowiedzialności

Wszystkie zawarte w niniejszej instrukcji obsługi informacje techniczne, dane,

wskazówki montażu i podłączania oraz obsługi, są aktualne na dzień prze-

kazania do druku i uwzględniają nasze dotychczasowe doświadczenie oraz

spostrzeżenia zgodnie z najlepszą wiedzą.

Na podstawie zawartych tu informacji, ilustracji i opisów nie można wysuwać

żadnych roszczeń.

Producent nie ponosi żadnej odpowiedzialności za szkody spowodowane nie-

przestrzeganiem instrukcji, użytkowaniem urządzenia niezgodnie z przeznacze-

niem, niefachowymi naprawami, niedozwolonymi przeróbkami ani używaniem

niedozwolonych części zamiennych.

Użytkowanie zgodne z przeznaczeniem

Urządzenie jest przeznaczone wyłącznie do laminowania na gorąco i na zimno

dokumentów z papieru i tektury w warunkach domowych. Urządzenie nie jest

przeznaczone do zastosowań przemysłowych ani profesjonalnych.

Inne lub wykraczające poza powyższe użytkowanie uznaje się za niezgodne

z przeznaczeniem. Wszelkie roszczenia z tytułu szkód wynikających z użytko-

wania niezgodnego z przeznaczeniem są wykluczone. Ryzyko ponosi wyłącznie

użytkownik.

IB_100158_ULGD350A1_LB4.indb 16 02.07.14 13:42

ULGD 350 A1

Zastosowane wskazówki ostrzegawcze

W niniejszej instrukcji obsługi zastosowano następujące wskazówki ostrzegawcze:

NIEBEZPIECZEŃSTWO

Wskazówka ostrzegawcza tego stopnia zagrożenia oznacza

zagrażającą sytuację niebezpieczną.

Nieuniknięcie niebezpiecznej sytuacji może doprowadzić do śmierci lub

powstania ciężkich obrażeń.

► Należy przestrzegać instrukcji w niniejszej wskazówce ostrzegawczej,

aby uniknąć zagrożenia śmiercią lub ciężkich obrażeń ciała.

OSTRZEŻENIE

Wskazówka ostrzegawcza tego stopnia zagrożenia oznacza

możliwą sytuację niebezpieczną.

Nieuniknięcie niebezpiecznej sytuacji może doprowadzić do powstania

obrażeń.

► Należy przestrzegać instrukcji zawartych w niniejszej wskazówce

ostrzegawczej, by uniknąć obrażeń u osób.

UWAGA

Wskazówka ostrzegawcza tego stopnia zagrożenia oznacza

możliwą szkodę materialną.

Nieuniknięcie takiej sytuacji może doprowadzić do powstania szkód materialnych.

► Należy przestrzegać instrukcji zawartych w niniejszej wskazówce

ostrzegawczej, by uniknąć szkód materialnych.

WSKAZÓWKA

►

Wskazówka oznacza dodatkowe informacje, ułatwiające korzystanie

z urządzenia.

IB_100158_ULGD350A1_LB4.indb 17 02.07.14 13:42

Stránka sa načítava ...

UNITED OFFICE ULGD 350 A1 Operating Instructions Manual

Značka: UNITED OFFICE

Model: ULGD 350 A1

Kategória: Laminátory

Typ: Operating Instructions Manual

Táto príručka je tiež vhodná pre

100158

Stiahnite si PDF

správa

V iných jazykoch

Deutsch: UNITED OFFICE ULGD 350 A1
polski: UNITED OFFICE ULGD 350 A1

UNITED OFFICE ULGD 350 A1 Operating Instructions Manual

Táto príručka je tiež vhodná pre

UNITED OFFICE ULGD 350 A1 Operating Instructions Manual

V iných jazykoch

Súvisiace články

Ďalšie dokumenty