Silvercrest SRR 3.7 B2 Operating Instructions Manual

ROTARY SHAVER SRR 3.7 B2

ROTARY SHAVER

Operating instructions

IAN 275652

KÖRKÉSES BOROTVA

Használati utasítás

ROTACIJSKI BRIVNIK

Navodila za uporabo

HOLICÍ STROJEK

Návod k obsluze

HOLIACI STROJČEK

Návod na obsluhu

ROTATIONSRASIERER

Bedienungsanleitung

GB Operating instructions Page 1

HU Használati utasítás Oldal 23

SI Navodila za uporabo Stran 45

CZ Návod k obsluze Strana 65

SK Návod na obsluhu Strana 87

DE / AT / CH Bedienungsanleitung Seite 109

Before reading, unfold both pages containing illustrations and familiarise

yourself with all functions of the device.

Olvasás előtt kattintson az ábrákat tartalmazó mindkét oldalra és végezetül

ismerje meg a készülék mindegyik funkcióját.

Pred branjem obe strani s slikami odprite navzven in se nato seznanite z

vsemi funkcijami naprave.

Před čtením si odklopte obě dvě strany s obrázky a potom se seznamte se

všemi funkcemi přístroje.

Pred čítaním si odklopte obidve strany s obrázkami a potom sa oboznámte

so všetkými funkciami prístroja.

Klappen Sie vor dem Lesen die beiden Seiten mit den Abbildungen aus und

machen Sie sich anschließend mit allen Funktionen des Gerätes vertraut.

A

B

GB

│

1 ■

SRR 3.7 B2

Contents

Introduction ...................................2

Intended use ..................................2

Package contents ..............................2

Description of the appliance ......................3

Technical data .................................4

Safety guidelines ..............................5

Charging the battery ...........................9

Cordless shaving ..............................10

Shaving with mains voltage .....................11

Trimmer / long hair trimmer .....................11

Cleaning and care .............................12

Cleaning with the brush .................................12

Cleaning under running water ............................13

Thorough cleaning .....................................14

Storage .....................................16

Warranty and service ..........................17

Disposal .....................................18

Importer .....................................21

■ 2

│

GB

SRR 3.7 B2

Introduction

Congratulations on the purchase of your new appliance.

You have selected a high-quality product. The operating instructions

are part of this product. They contain important information on safety,

usage and disposal. Before using the product, familiarise yourself

with all handling and safety guidelines. Use the product only as

described and for the range of applications speciﬁed. Please also

pass these operating instructions on to any future owner(s).

Intended use

This appliance is intended exclusively for shaving and trimming

human hair.

This appliance is intended solely for use in private households.

Do not use it for commercial applications.

All other uses are deemed to be improper and may result in property

damage or even in personal injury.

Package contents

♦ Shaver with cutting unit

♦ Power cable

♦ Protective cap

♦ Brush

♦ Case

♦ Operating instructions

♦ Order card

GB

│

3 ■

SRR 3.7 B2

NOTE

Check contents for completeness and damage immediately

after unpacking. Contact Customer Services if necessary.

Description of the appliance

Figure A (front fold-out page):

Protective cap

Cutting unit

Long hair trimmer

Release button, cutting unit

Catch for the long hair trimmer

On/Oﬀ switch

On/Oﬀ switch lock

Green power light

Red charge indicator light

Mains connection

Figure B (rear fold-out page):

-Power plug

3Connector

!Brush

.Case

■ 4

│

GB

SRR 3.7 B2

Technical data

Device

Operating voltage: 220V − 240 V

~

, 50 Hz

Power consumption: max. 8W

Battery: 3.7 V/700 mAh Li-ion battery

Protection class: II/

Charging time: approx. 60 minutes

Operating time with

fully charged battery: approx. 60 minutes

GB

│

5 ■

SRR 3.7 B2

Safety guidelines

DANGER – RISK OF ELECTRIC SHOCK!

► Prior to use, check the appliance for visible

external damage. Never operate an appliance

that is damaged. There is a risk of electrocution.

► The appliance may no longer be used if there

is any damage to the cable, the housing or any

other components.

► Disconnect the power cable from the wall

socket

— if a defect occurs,

— before cleaning the appliance,

— after every use.

Pull directly on the power plug and not on the

cable.

► Never submerge the appliance or the cable in

water or other liquids.

Do not use this appliance near bath

tubs, showers or other containers ﬁlled

with water.

■ 6

│

GB

SRR 3.7 B2

DANGER – RISK OF ELECTRIC SHOCK!

► If the appliance drops into water, pull the plug

out of the power socket before you reach into

the water!

► Never touch the power plug with wet hands,

especially when plugging it in or unplugging it.

Risk of electrocution!

► Check the power cable and appliance regularly

for possible mechanical defects.

► Ensure that the power cable does not get

jammed in cupboard doors and that it is never

laid on hot surfaces. If this occurs, the cable

insulation may be damaged.

► The installation of a residual current circuit

breaker with a rated tripping current of no

more than 30mA oﬀers further protection from

electric shocks. Have the installation carried out

only by a qualiﬁed electrician.

► CAUTION! Keep the appliance dry.

GB

│

7 ■

SRR 3.7 B2

WARNING – RISK OF INJURY!

► This appliance may be used by children aged

8 years and above and by persons with limited

physical, sensory or mental capabilities or lack

of experience and knowledge, provided that

they are under supervision or have been told

how to use the appliance safely and are aware

of the potential risks.

► Children must not use the appliance as a play-

thing.

► Cleaning and user maintenance tasks may

not be carried out by children unless they are

supervised.

► All repairs must be carried out by authorised

specialist companies or by the Customer Service

department. Improper repairs can pose signiﬁ-

cant risks to the user. It will also invalidate any

warranty claims.

► Do not use the appliance with a defective cutting

unit or long hair trimmer because these may

have sharp edges. There is a risk of personal

injury!

■ 8

│

GB

SRR 3.7 B2

WARNING – RISK OF INJURY!

► Defective components must always be replaced

with original replacement parts. Compliance

with safety requirements can only be guaranteed

if original replacement parts are used.

► Only plug the power plug into an easily acces-

sible power socket so that you can pull it out of

the power socket quickly in an emergency.

CAUTION – PROPERTY DAMAGE!

► Never operate the appliance unsupervised,

and only in accordance with the information

on the nameplate.

► Use only the supplied power cable provided

when using mains power.

► Remove the cutting unit from the handset for

cleaning under running water.

GB

│

9 ■

SRR 3.7 B2

Charging the battery

The battery should be charged for at least 60 minutes before ﬁrst use.

NOTE

► Ensure that the appliance is switched oﬀ before charging the

battery.

1) Plug the connector 3 into the mains connection  on the shaver.

2) Plug the power plug - into a socket that is compatible with the

appliance speciﬁcations. While the battery is charging, the red

charge indicator light lights up.

♦ As soon as the battery is fully charged, the green power light 

ﬂashes. Disconnect the appliance from the mains voltage.

The green power light  switches oﬀ.

♦ Once the battery is fully charged, you can use the appliance for

around 60 minutes without connecting it to the power supply.

♦ If the red indicator light  ﬂashes, the battery charge level is

too low. Recharge the battery in that case.

■ 10

│

GB

SRR 3.7 B2

Cordless shaving

CAUTION! MATERIAL DAMAGE!

► This appliance is not suitable for wet shaving!

This shaver can be used without the power cable. In this case, you

must charge the appliance before ﬁrst use (see section “Charging

the battery”).

1) Ensure the cutting unit  is attached and locked in place.

2) Remove the protective cap .

3) Press the switch lock  and push the on/oﬀ switch  towards

the cutting unit . The green power light  lights up and the

shaver starts.

NOTE

► The best results are achieved if used on dry skin.

► It can take 2 to 3 weeks until the skin is accustomed to the

dry shaving system.

4) Move the shaving heads with straight and circular motions over

the skin.

5) After you covered all the areas you want to shave, set the on/oﬀ

switch  back into its initial position. The appliance stops and

the green power light  switches oﬀ.

6) Clean the shaver after every use with the supplied brush !.

For a more thorough cleaning, read the section “Cleaning and

care”.

GB

│

11 ■

SRR 3.7 B2

Shaving with mains voltage

CAUTION! MATERIAL DAMAGE!

► This appliance is not suitable for wet shaving!

If you want to use the shaver without previously charging it, you can

also use it directly with mains voltage:

1) Plug the connector 3 into the mains connection  on the shaver.

2) Plug the power plug - into a mains socket that complies with

the appliance speciﬁcations.

You can then use the shaver as described in the section “Cordless

shaving”.

Trimmer / long hair trimmer

To shape your beard, form sideburns or shave eyebrows, use the

long hair trimmer .

1) To do this, push the catch  of the long hair trimmer  away

from it. The long hair trimmer  ﬂips out.

2) Press the switch lock  and push the on/oﬀ switch  towards

the cutting unit . The green power light  lights up and the

shaver starts the cutting unit  and the long hair trimmer .

3) After you ﬁnish trimming, press the on/oﬀ switch  back to its

initial position.

4) Clean the long hair trimmer  with the supplied brush !. For a

more thorough cleaning, read the section “Cleaning and care”.

■ 12

│

GB

SRR 3.7 B2

Cleaning and care

DANGER – ELECTRIC SHOCK!

► Before cleaning the device, disconnect the power plug -

from the mains power socket! There is a risk of electric shock!

CAUTION! MATERIAL DAMAGE!

► Do not use abrasive, chemical or caustic cleaning agents

to clean this appliance. This will irreparably damage the

appliance.

Cleaning with the brush

Cutting unit

Clean the 3 shaving heads of the cutting unit  after every shave

using the brush !.

1) Press the release button  so that the cutting unit  pops

open/can be folded back.

2) Tap the cutting unit  on a ﬂat surface or blow oﬀ the hair

cuttings.

3) Use the brush ! to remove any remaining hair cuttings.

Long hair trimmer

■ Clean the long hair trimmer  after every use with the supplied

brush !.

■ Oil the long hair trimmer  around every 6 months with a drop

of sewing machine oil.

GB

│

13 ■

SRR 3.7 B2

Cleaning under running water

1) Press the release button  so that the cutting unit  pops open.

2) Overstretch the cutting unit  a little so it can be pulled upwards

and oﬀ.

3) Hold the cutting unit  under the running water so that the water

ﬂows through the shaving heads from the inside to the outside.

CAUTION! MATERIAL DAMAGE!

Hold only the cutting unit  under running water! The shaver

handset can be damaged irreparably if it is held under running

water.

4) Allow the cutting unit  to dry.

5) Replace the cutting unit  on the shaver. Ensure that it snaps

into place and is seated ﬁrmly:

■ 14

│

GB

SRR 3.7 B2

Thorough cleaning

For a more thorough cleaning, remove the shaving heads:

1) Press the release button . The cutting unit  pops up.

2) Overstretch the cutting unit  a little so it can be pulled upwards

and oﬀ.

3) Press the black gear wheel down slightly and turn it carefully

anticlockwise until the shaving head holder can be lifted out

(see Figure 1).

Figure 1

4) Clean all parts under running water and then allow them to dry

fully.

GB

│

15 ■

SRR 3.7 B2

5) Replace the cutting unit . Refer to ﬁgure 1 for assistance:

– Insert the 3 shaving heads in the recesses of the cutting

unit . Ensure that the notches on the edge of the shaving

heads rest on the catches in the opening.

– Place the round blades into the shaving heads.

– Replace the shaving head holder, press it down a little and

slightly turn the gear wheel clockwise.

NOTE

If the holder for the shaving heads cannot be reat-

tached, it may be that the gear wheel is a little skew.

In this case, turn the gear wheel anticlockwise again

up to the stop. The holder for the shaving heads can

then be ﬁtted.

The cutting unit  is now installed again.

6) Remove loose hairs from the shaver with the brush !.

7) Replace the cutting unit  on the shaver. Ensure that it snaps

into place and is seated ﬁrmly.

■ Clean the housing with a moist cloth.

■ 16

│

GB

SRR 3.7 B2

NOTE

If...

– ... the shaving result is noticeably poorer, ...

– ... you have to the shave the same spot repeatedly

to achieve a good result, ...

– ... the shave takes much longer than usual, ...

– ... there is visible damage to the shaving heads, ...

... the shaving heads/the cutting unit  must be replaced.

You can order the cutting unit , incl. shaving heads from

our customer service (see order card).

To replace the cutting unit  proceed as follows:

1) Press the release button  so that the cutting unit 

pops open.

2) Overstretch the cutting unit  a little so it can be pulled

upwards and oﬀ.

3) Fit the new cutting unit  onto the shaver. Ensure that it

snaps into place and is seated ﬁrmly.

Storage

CAUTION! MATERIAL DAMAGE!

Never store the shaver in the case . while the appliance is

charging. Risk of overheating!

■ Always replace the protective cap  onto the cutting unit  when

you are not using the appliance. Ensure that the corner with the

long plastic sleeve lies above the release button . Otherwise,

the protective cap  cannot be ﬁtted.

Stránka sa načítava...

Silvercrest SRR 3.7 B2 Operating Instructions Manual

Silvercrest SRR 3.7 B2 Operating Instructions Manual

v iných jazykoch

Súvisiace články

Ostatné dokumenty