Parkside PAEXS 20-Li A1 Návod na používanie

Kategória
Elektrické náradie
Typ
Návod na používanie
CORDLESS ORBITAL SANDER / AKKU-EXZENTER-
SCHLEIFER / PONCEUSE EXCENTRIQUE SANS FIL
PAEXS 20-Li A1
PONCEUSE EXCENTRIQUE SANS FIL
Traduction des instructions d’origine
AKKU-EXZENTERSCHLEIFER
Originalbetriebsanleitung
CORDLESS ORBITAL SANDER
Translation of the original instructions
AKU EXCENTRICKÁ BRUSKA
Překlad originálního provozního návodu
ACCU-EXCENTERSCHUURMACHINE
Vertaling van de originele gebruiksaanwijzing
AKKU-EXZENTERSCHLEIFER
Preklad originálneho návodu na obsluhu
AKUMULATOROWA SZLIFIERKA
MIMOŚRODOWA
Tłumaczenie oryginalnej instrukcji obsługi
LIJADORA EXCÉNTRICA
RECARGABLE
Traducción del manual de instrucciones original
BATTERIDREVEN EXCENTERSLIBER
Oversættelse af den originale driftsvejledning
IAN 351737_2007
GB Translation of the original instructions Page 1
DE Originalbetriebsanleitung Seite 15
FR Traduction des instructions d’origine Page 29
NL Vertaling van de originele gebruiksaanwijzing Pagina 45
CZ Překlad originálního provozního návodu Strana 59
PL Tłumaczenie oryginalnej instrukcji obsługi Strona 73
SK Preklad originálneho návodu na obsluhu Strana 87
ES Traducción del manual de instrucciones original Página 101
DK Oversættelse af den originale driftsvejledning Side 115
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of
the device.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen
Funktionen des Gerätes vertraut.
Avant de lire le mode d‘emploi, ouvrez la page contenant les illustrations et familiarisez-vous ensuite avec
toutes les fonctions de l‘appareil.
Vouw vóór het lezen de pagina met de afbeeldingen open en maak u vertrouwd met alle functies van het
apparaat.
Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.
Przed przeczytaniem proszę rozłożyć stronę z ilustracjami, a następnie proszę zapoznać się z wszystkimi
funkcjami urządzenia.
Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.
Antes de empezar a leer abra la página que contiene las imágenes y, en seguida, familiarícese con todas
las funciones del dispositivo.
Før du læser, vend siden med billeder frem og bliv bekendt med alle apparatets funktioner.
A
20V max.
18V
Alle Parkside Geräte und die Lade geräte PLG 20 A1/A4/PLG 20 A2/PLG20A3/
PDSLG 20 A1 der X20V Team Serie sind mit dem Akku-Pack PAP 20 A1/PAP 20 A2/
PAP20 A3/PAP 20 B1/PAP 20 B3 kompatibel.
All Parkside tools and the chargers PLG20A1/PLG20A2/PLG20A3/PDSLG 20 A1 of the
X20V Team series are compatible with the PAP20 A1/PAP20A2 / PAP 20 A3 /PAP 20 B1/
PAP 20 B3battery pack.
Tous les outils Parkside et les chargeurs PLG 20 A1/PLG20A2/PLG 20 A3/PDSLG 20 A1 de
la série X20V Team sont compatibles avec la batterie PAP 20 A1/PAP 20 A2/PAP 20 A3/
PAP 20 B1/PAP 20 B3.
Ladezeiten
Charging times
Temps de charge
Ladeströme
Charging currents
Courants de charge
2 Ah
Akku
Battery pack
Batterie
PAP 20 A1/B1
3 Ah
Akku
Battery pack
Batterie
PAP 20 A2
4 Ah
Akku
Battery pack
Batterie
PAP 20 A3/B3
max. 2,4 A
Ladegerät PLG 20 A1/A4
Charger
Chargeur
60 min
2,4 A
90 min
2,4 A
120 min
2,4 A
max. 3,5 A
Ladegerät PLG 20 A2
Charger
Chargeur
45 min
3,5 A
60 min
3,5 A
80 min
3,5 A
max. 4,5 A
Ladegerät PLG 20 A3
Charger
Chargeur
35 min
3,8 A
45 min
4,5 A
60 min
4,5 A
max. 4,5 A
Ladegerät PDSLG 20 A1
Charger
Chargeur
35 min
3,8 A
45 min
4,5 A
60 min
4,5 A
PAEXS 20-Li A1 GBIE 1
Contents
Introduction ............................................................ 2
Intended use ........................................................................2
Features ...........................................................................2
Package contents ....................................................................2
Technical specifications ...............................................................2
General power tool safety warnings .......................................3
1. Work area safety ..................................................................3
2. Electrical safety ...................................................................3
3. Personal safety ....................................................................4
4. Power tool use and care ............................................................4
5. Use and handling of the cordless electrical power tool .....................................5
6. Service ..........................................................................5
Safety guidelines for battery chargers ....................................................6
Appliance-specific safety instructions .....................................................6
Original accessories/auxiliary equipment .................................................7
Before use ............................................................. 7
Charging the battery pack (seefig.A) ....................................................7
Attaching/disconnecting the battery pack to/from the appliance ...............................8
Checking the battery charge level .......................................................8
Selecting a sanding sheet ..............................................................8
Fitting the sanding sheet ...............................................................8
Dust extraction ......................................................................8
Dust box ..........................................................................9
Reducer ...........................................................................9
Use ...................................................................9
Adjusting the additional handle .........................................................9
Switching on and off .................................................................9
Setting the rotational speed ............................................................9
Working procedures ..................................................................9
Maintenance and cleaning ...............................................10
Kompernass Handels GmbH warranty ....................................10
Service ...............................................................12
Importer .............................................................12
Disposal ..............................................................12
Original Declaration of Conformity .......................................13
Ordering a replacement battery ..........................................14
Telephone ordering .................................................................14
PAEXS 20-Li A1
2 GBIE
CORDLESS ORBITAL SANDER
PAEXS 20-Li A1
Introduction
Congratulations on the purchase of your
new appliance. You have selected a high-
quality product. The operating instructions
are part of this product. They contain important
information about safety, usage and disposal.
Before using the product, please familiarise your-
self with all the operating and safety instructions.
Use the product only as described and for the
range of applications specified. Please also pass
these operating instructions on to any future owner.
Intended use
Depending on the sandpaper being used, this
appliance is suitable for the dry sanding of wood,
plastic, metal, filler and also painted surfaces.
Any other usage or modification of the appliance
is deemed to be improper and carries a significant
risk of accidents. The manufacturer accepts no
responsibility for damage(s) resulting from
improper usage. This appliance is not intended for
commercial use.
Features
ON/OFF switch
Release button
Tab (dust box)
Dust box
Reducer for external extraction appliances
Adapter fitting
Sanding sheet
Sanding plate
Screw
Additional handle
Speed setting wheel
Figure A
Battery display LED
Battery charge level button
Battery pack*
Quick charger*
Green control LED
Red control LED
Package contents
1 cordless Orbital Sander
4 random orbital sanding discs
(grain size 60/80/120/240)
1 dust box
1 reducer for external extraction appliances
1 set of operating instructions
Technical specifications
Cordless Orbital Sander PAEXS 20-Li A1
Rated voltage 20 V (DC)
Rated speed n0 3000–12000 rpm
Sanding sheet Ø 125mm
Battery PAP 20 A1*
Type LITHIUM-ION
Rated voltage 20 V (DC)
Capacity 2 Ah
Cells 5
High-speed battery charger PLG 20 A1*
INPUT
Rated voltage 230–240 V ∼, 50 Hz
(AC)
Rated power
consumption 65 W
Fuse (internal) 3.15 A T3.15A
OUTPUT
Rated voltage 21.5 V (DC)
Rated current 2.4 A
Charging time approx. 60 min
Protection class II / (double insulation)
* BATTERY AND CHARGER ARE NOT SUPPLIED
PAEXS 20-Li A1 GBIE 3
Noise and vibration data
Noise measurement value determined in
accordance with EN 62841. The A-rated noise
level of the power tool is typically as follows
Sound pressure level LPA = 82.3 dB (A)
Sound power level LWA = 93.3 dB (A)
Uncertainty K = 3 dB
Wear ear muffs!
Rated acceleration, typically
Main handle ah = 10.6 m/s2
Uncertainty K = 1.5 m/s2
Additional handle ah = 18.6 m/s2
Uncertainty K = 1.5 m/s2
NOTE
The vibration emission values and the noise
emission values given in these instructions
have been measured in accordance with
a standardised test procedure and can be
used for comparison of the power tool with
another tool.
The specified total vibration values and the
noise emission values can also be used to
make a provisional load estimate.
WARNING!
Depending on the manner in which the
power tool is being used, and in particular
the kind of workpiece being worked, the
vibration and noise emission values can
deviate from the values given in these instruc-
tions during actual use of the power tool.
Try to keep the vibration load as low as
possible. Measures to reduce the vibration
load are, e.g. wearing gloves and limiting
the working time. Wherein all states of oper-
ation must be included (e.g. times when the
power tool is switched off and times where
the power tool is switched on but running
without load).
General power tool
safety warnings
WARNING!
Read all safety warnings, instructions, illus-
trations and specifications provided with
this power tool. Failure to follow all instruc-
tions listed below may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future
reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-
operated (cordless) power tool.
1. Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmos-
pheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
2. Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way.
Do not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of electric
shock.
b) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of
electric shock if your body is earthed or
grounded.
PAEXS 20-Li A1
4 GBIE
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
e) When working outdoors with an electrical
power tool, always use extension cords that
are also suitable for use outdoors. Use of a
cord suitable for outdoor use reduces the risk of
electric shock.
f) If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
3. Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired
or under the influence of drugs, alcohol or
medication. A moment of inattention while
operating a power tool may result in serious
personal injury.
b) Use
personal protective equipment. Always
wear eye protection. Protective equipment such
as a dust mask, non-skid safety shoes, hard hat
or hearing protection used for appropriate condi-
tions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools
with your finger on the switch or energising
power tools that have the switch on invites
accidents.
d) Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key
left attached to a rotating part of the power tool
may result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair and clothing away
from moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used.
Use of dust collection can reduce dust-related
hazards.
h) Do not allow yourself to get lulled into a false
sense of security and do not ignore the safety
rules for power tools, even if you are familiar
with the power tool after repeated use.
A careless action can cause severe injury within
a fraction of a second.
4. Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at
the rate for which it was designed.
b) Do not use the power tool if the switch does
not turn it on and off. Any power tool that
cannot be controlled with the switch is
dangerous and must be repaired.
c) Disconnect the plug from the power source
and/or remove the battery pack, if detachable,
from the power tool before making any
adjustments, changing accessories, or storing
power tools. Such preventive safety measures
reduce the risk of starting the power tool acci-
dentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
PAEXS 20-Li A1 GBIE 5
e) Maintain power tools and accessories. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool’s operation.
If damaged, have the power tool repaired
before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
g) Use the power tool, accessories and acces-
sory tools etc. in accordance with these
instructions, taking into account the working
conditions and the work to be performed.
Use of the power tool for operations different
from those intended could result in a hazardous
situation.
h) Keep handles and grasping surfaces dry,
clean and free from oil and grease. Slippery
handles and grasping surfaces do not allow
for safe handling and control of the tool in un ex-
pected situations.
5. Use and handling of the cordless
electrical power tool
a) Charge a rechargeable battery using only
the charger recommended by the manufac-
turer. Chargers are often designed for a
particular type of rechargeable battery unit.
There is a risk of fire if a battery charger speci-
fied for a particular type of battery is used with
other batteries.
b) Only the rechargeable battery units supplied
are to be used with an electrical power tool.
The use of other rechargeable battery units may
lead to the danger of injury or fire.
c) When they are not being used, store
rechargeable battery units away from paper-
clips, coins, keys, nails, screws or other small
metal objects that could cause the contacts to
be bridged. Short-circuiting the contacts of a
rechargeable battery unit may result in heat
damage or fire.
d) Fluids may leak out of rechargeable battery
units if they are misused. If this happens,
avoid contact with the fluid. If contact occurs,
flush the affected area with water. Seek addi-
tional medical help if any of the fluid gets into
your eyes. Escaping battery fluid may cause
skin irritation or burns.
e) Do not use damaged or modified batteries.
Damaged or modified batteries may behave
unexpectedly and cause fires, explosions or
pose a risk of injury.
f) Do not expose a battery to fire or excessively
high temperatures. Fire or temperatures in
excess of 130°C (265°F) can cause an ex plo-
sion.
g) Follow all instructions regarding charging
and never charge the battery or the cordless
tool outside of the temperature range given in
the operating instructions. Incorrect charging
or charging outside of the permissible tempera-
ture range can destroy the battery and increase
the risk of fire.
CAUTION! RISK OF EXPLOSION!
Never charge non-rechargeable
batteries.
Protect the recharge-
able battery from heat (for example, from
continuous exposure to sunlight), fire, water
and moisture. There is a risk of explosion.
6. Service
a) Have your power tool serviced by a qualified
repair person using only identical replace-
ment parts. This will ensure that the safety of
the power tool is maintained.
b) Never try to repair damaged batteries.
Batteries should only be maintained by the
manufacturer or an approved customer service
centre.
PAEXS 20-Li A1
6 GBIE
Safety guidelines for battery
chargers
This appliance may be used by
children aged 8 years and above
and by persons with limited physical,
sensory or mental capabilities or
lack of experience and knowledge,
provided that they are under super-
vision or have been told how to use
the appliance safely and are aware
of the potential risks. Do not allow
children to use the appliance as a
toy. Cleaning and user maintenance
tasks may not be carried out by
children unless they are supervised.
To avoid potential risks, damaged
mains cables should be replaced
by the manufacturer, their customer
service department or a similarly
qualified person.
The charger is suitable for indoor use only.
ATTENTION!
This charger can only charge the following
batteries: PAP 20 A1/PAP 20 A2/
PAP20 A3/PAP 20 B1/PAP 20 B3.
A current list of battery compatibility can be
found at www.Lidl.de/Akku.
WARNING!
Do not operate the charger with a damaged
cable, power cord or plug. Damaged power
cords can result in danger to life due to
electric shock.
Appliance-specific safety instructions
Secure the workpiece. A workpiece securely
held by a clamping device or vice is much safer
than one held in your hand.
Do not rest your hands next to or in front of the
appliance and the area being worked as there
is a risk of injury if you slip.
RISK OF FIRE DUE TO FLYING SPARKS!
Sanding metal causes sparks to be produced.
Therefore, make sure that nobody is at risk and
that no combustible materials are located in the
immediate vicinity of where you are working.
WARNING! TOXIC VAPOURS!
Working with the tool can produce harmful/
toxic dusts that represent a health hazard for
the person operating the appliance and for
any other people in the area.
WARNING!
RISKS DUE TO DUST!
When working for extended periods of time
on wood and, in particular, materials that
produce dust that is hazardous to health,
connect the appliance to a suitable external
dust extraction appliance. Wear safety
goggles and a protective dust mask!
Provide sufficient ventilation when working on
plastics, paints, lacquers, etc.
Do not soak the materials or the area to be
processed with liquids containing solvents.
Never work on moistened materials or damp
surfaces.
PAEXS 20-Li A1 GBIE 7
Avoid sanding lead paint or other harmful
materials.
Materials containing asbestos must not be
processed. Asbestos is a known carcinogen.
Avoid contact with the sanding sheet while the
appliance is running.
Do not use the appliance without a sanding
sheet fitted.
Never use the appliance for other purposes and
only use original parts/accessories. Using
attachments or accessory tools other than those
recommended in the operating instructions can
lead to a risk of injury.
Always allow the appliance to come to a
complete standstill before putting it down.
The appliance must always be kept clean,
dry and free from oil or grease.
Original accessories/auxiliary
equipment
Use only the accessories and additional
equipment that are specified in the operating
instructions and are compatible with the
appliance.
WARNING!
Do not use any accessories that are not
recommended by PARKSIDE. This can lead to
an electric shock and fire.
Before use
Charging the battery pack
(seefig.A)
CAUTION!
Always unplug the appliance before you
remove the battery pack from or connect
the battery pack to the high-speed charger .
NOTE
Never charge the battery pack at an ambient
temperature of below 10°C or above 40°C.
If a lithium-ion battery is to be stored for an
extended period, the charge level should be
checked regularly. The optimum charge level
is between 50% and 80%. The storage
climate should be cool and dry and the
ambient temperature should be between 0°C
and 50°C.
Plug the battery pack into the high-speed
charger (see fig. A).
Insert the power plug into the socket. The red
control LED lights up.
The green LED indicates that the charging
process is complete and the battery pack is
ready.
ATTENTION!
If the red control LED flashes, this means
that the battery pack has overheated and
cannot be charged.
If the red and green control LEDs both
flash, this means that the battery pack is
defective.
Disconnect the power plug from the mains
power socket. Remove the battery pack from
the high-speed charger .
Never recharge a battery pack again imme-
diately after rapid charging. There is a risk that
the battery pack will overheat, which will
reduce the lifespan of the again.
Switch the high-speed charger off for at least
15 minutes between successive charging
processes. Also disconnect the power plug from
the mains power socket.
PAEXS 20-Li A1
8 GBIE
Attaching/disconnecting the battery
pack to/from the appliance
Inserting the battery pack
Push the battery pack into the handle until it
clicks into place.
Removing the battery pack
Press the release button and remove the
battery pack .
Checking the battery charge level
To check the battery status, press the battery
charge level button (see fig. A). The status
will be shown on the battery display LED as
follows:
RED/ORANGE/GREEN = maximum charge
RED/ORANGE = medium charge
RED = low charge – charge the battery
Selecting a sanding sheet
Removal and surface
The material removal rate and surface quality are
determined by the grain strength of the sanding
sheet.
Please note that you need to use appropriate
sanding sheets with different grains for working
different materials.
Fitting the sanding sheet
WARNING!
Remove the battery pack before carrying out
any work on the appliance.
NOTE
Before fitting a new sanding sheet , remove
any dust and dirt from the sanding plate .
Attaching sanding sheets using Velcro
You can attach the sanding sheet to the
sanding plate using the Velcro.
Make sure that the extraction holes on the
sanding sheet match up with those on the
sanding plate .
Removing sanding sheets fitted using Velcro
Simply pull the sanding sheet off the sanding
plate .
Dust extraction
WARNING! RISK OF FIRE!
There is a risk of fire when working with
power tools fitted with a dust collection box
or which can be connected to a vacuum
cleaner via the vacuum cleaner adapter! In
unfavourable conditions, e.g. when sparks
are flying while sanding metal or metal resi-
dues in wood, wood dust in the dust sack (or
in the vacuum cleaner dust bag) can sponta-
neously ignite. This is a particular risk if the
wood dust is mixed with paint residues or
other chemicals and the workpiece has
become hot after being worked for a long
time. Therefore, do not allow the workpiece
to overheat and always empty the dust box
or the dust bag in the vacuum cleaner before
taking a break from work.
Wear a dust mask!
NOTE
Perforated sanding sheets are required for
dust extraction.
PAEXS 20-Li A1 GBIE 9
Dust box
Connecting
Slide the dust box onto the appliance as far
as the stop.
Removal
Pull the dust box off the appliance.
NOTE
To achieve optimum dust extraction, the dust
box should be emptied regularly.
To do this, remove the dust box from the
appliance as described above. Open the dust
box by pulling on the tab and then removing
the lid. Clean both parts thoroughly by tapping.
Reducer
Connecting
Push the reducer for external extraction appli-
ances into the adapter fitting .
Push the hose from a suitable dust extraction
appliance (e.g. a workshop vacuum cleaner)
onto the reducer for external extraction appli-
ances .
Removal
Pull the hose of the vacuum cleaner off the
reducer for external extraction appliances .
Remove the reducer .
Use
NOTE
Always switch on the appliance before contact
with the material and then apply the tool to the
workpiece.
Adjusting the additional handle
You can adjust the additional handle to several
different positions.
To reposition the additional handle undo
the screw .
Move the additional handle to the required
position.
Retighten the screw .
Switching on and off
Switching the appliance on
Move the ON/OFF switch to the "I" position.
Switching the appliance off
Move the ON/OFF switch to the "0" position.
Setting the rotational speed
Adjust the speed setting wheel to a position
between 1 and 6.
Working procedures
Switch the appliance on before applying it to
the workpiece.
Apply minimal pressure when working.
Work at a constant speed.
Change the sanding sheets regularly.
Never use the same sanding sheet for sanding
different materials (e.g. wood followed by
metal). Optimum sanding results can only be
achieved by using clean sanding sheets.
PAEXS 20-Li A1
10 GBIE
Clean the sanding sheet every once in a while
using a vacuum cleaner.
Sand hard-to-reach places with the front or side
edge of the sanding sheet on the sander plate.
Guide the sander over the workpiece in parallel
and use overlapping sanding motions.
After completing the task, lift the appliance from
the workpiece and then switch it off.
Maintenance and cleaning
WARNING! RISK OF INJURY!
Before carrying out any work on the
appliance, switch off the appliance
and remove the battery pack.
The appliance is maintenance-free.
Always clean the appliance immediately after
completing work.
Use a dry cloth to clean the housing.
Remove any sanding dust stuck to the appliance
with a brush.
Never use sharp objects, petrol, solvents or
cleaning agents which can damage plastic.
Do not allow any liquids to get into the interior
of the appliance.
Always keep the ventilation openings free of
obstructions.
Kompernass Handels GmbH
warranty
Dear Customer,
This appliance has a 3-year warranty valid from the
date of purchase. If this product has any faults, you,
the buyer, have certain statutory rights. Your statu-
tory rights are not restricted in any way by the
warranty described below.
Warranty conditions
The warranty period starts on the date of purchase.
Please keep your receipt in a safe place. This will
be required as proof of purchase.
If any material or manufacturing fault occurs within
three years of the date of purchase of the product,
we will either repair or replace the product for you
or refund the purchase price (at our discretion).
This warranty service requires that you present the
defective appliance and the proof of purchase
(receipt) within the three-year warranty period,
along with a brief written description of the fault
and of when it occurred.
If the defect is covered by the warranty, your
product will either be repaired or replaced by us.
The repair or replacement of a product does not
signify the beginning of a new warranty period.
X 12 V and X 20 V Team Series battery packs
come with a 3-year warranty valid from the date of
purchase.
PAEXS 20-Li A1 GBIE 11
Warranty period and statutory claims
for defects
The warranty period is not prolonged by repairs
effected under the warranty. This also applies to
replaced and repaired components. Any damage
and defects present at the time of purchase must be
reported immediately after unpacking. Repairs
carried out after expiry of the warranty period shall
be subject to a fee.
Scope of the warranty
This appliance has been manufactured in accord-
ance with strict quality guidelines and inspected
meticulously prior to delivery.
The warranty covers material faults or production
faults. The warranty does not extend to product
parts subject to normal wear and tear or to fragile
parts which could be considered as consumable
parts such as switches or parts made of glass.
The warranty does not apply if the product has
been damaged, improperly used or improperly
maintained. The directions in the operating instruc-
tions for the product regarding proper use of the
product are to be strictly followed. Uses and
actions that are discouraged in the operating
instructions or which are warned against must be
avoided.
This product is intended solely for private use and
not for commercial purposes. The warranty shall be
deemed void in cases of misuse or improper
handling, use of force and modifications / repairs
which have not been carried out by one of our
authorised Service centres.
The warranty period does not apply to
Normal reduction of the battery capacity
overtime
Commercial use of the product
Damage to or alteration of the product by the
customer
Non-compliance with safety and maintenance
instructions, operating errors
Damage caused by natural hazards
Warranty claim procedure
To ensure quick processing of your case, please
observe the following instructions:
Please have the till receipt and the item number
(e.g.IAN12345) available as proof of purchase.
You will find the item number on the type plate
on the product, an engraving on the product,
on the front page of the operating instructions
(below left) or on the sticker on the rear or
bottom of the product.
If functional or other defects occur, please
contact the service department listed either by
telephone or by e-mail.
You can return a defective product to us free of
charge to the service address that will be
provided to you. Ensure that you enclose the
proof of purchase (till receipt) and information
about what the defect is and when it occurred.
You can download these instructions
along with many other manuals,
product videos and installation
software at www.lidl-service.com.
This QR code will take you directly to the Lidl
service page (www.lidl-service.com) where you
can open your operating instructions by entering
the item number (IAN) 351737_2007.
WARNING!
Have the appliances repaired by the
Service Centre or a qualified electrician
and only using genuine replacement parts.
This will ensure that the safety of the appli-
ance is maintained.
PAEXS 20-Li A1
12 GBIE
Service
Service Great Britain
Tel.: 0800 404 7657
Service Ireland
Tel.: 1890 930 034
(0,08 EUR/Min., (peak))
(0,06 EUR/Min., (off peak))
IAN 351737_2007
Importer
Please note that the following address is not the
service address. Please use the service address
provided in the operating instructions.
KOMPERNASS HANDELS GMBH
BURGSTRASSE 21
44867 BOCHUM
GERMANY
www.kompernass.com
Disposal
The packaging is made from environ-
mentally friendly material which can be
disposed of at your local recycling
plant.
Do not dispose of power tools in
your normal domestic waste!
European Directive 2012/19/EU
requires that worn-out power tools be
collected separately and recycled in an environ-
mentally compatible manner.
Your local community or municipal authorities can
provide information on how to dispose of the
worn-out appliance.
Do not dispose of batteries in
your normal household waste!
Defective or worn-out rechargeable
batteries must be recycled according
toDirective 2006/66/EC. Take the battery pack
and/or tool to a nearby collection facility.
Please consult your local authorities regarding
suitable disposal of worn out power tools/battery
packs.
Dispose of the packaging in an
environmentally friendly manner. Note
the labelling on the packaging and
separate the packaging material
components for disposal if necessary. The pack-
aging material is labelled with abbreviations (a)
and numbers (b) with the following meanings:
1–7: plastics, 20–22: paper and cardboard,
80–98: composites.
Your local community or municipal
authorities can provide information
on how to dispose of the worn-out
product.
The product is recyclable, subject to
extended producer responsibility and is
collected separately.
PAEXS 20-Li A1 GBIE 13
Original Declaration of Conformity
We, KOMPERNASS HANDELS GMBH, document officer: Mr Semi Uguzlu, BURGSTR. 21,
44867 BOCHUM, GERMANY, hereby declare that this product complies with the following standards,
normative documents and EC directives:
Machinery Directive (2006/42/EC)
EC Low Voltage Directive (2014/35/EU, charger only)
EMC (Electromagnetic Compatibility) (2014/30/EU)
RoHS Directive (2011/65/EU)*
* The manufacturer bears the full responsibility for compliance with this conformity declaration. The object of the
declaration described above complies with the requirements of the Directive 2011/65/EU of the European Parliament
and Council of 8 June 2011 on the limitations of use of certain dangerous substances in electrical and electronic
appliances.
Applied harmonised standards
EN 62841-1:2015
EN 62841-2-4:2014
EN 60335-1:2012/A13:2017
EN 60335-2-29:2004/A2:2010
EN 62233:2008
EN 55014-1:2017
EN 55014-2:2015
EN 61000-3-2:2014
EN 61000-3-3:2013
EN 50581:2012
Type/appliance designation: Cordless Orbital Sander PAEXS 20-Li A1
Year of manufacture: 11–2020
Serial number: 351737_2007
Bochum, 17/11/2020
Semi Uguzlu
- Quality Manager -
We reserve the right to make technical changes in the sense of further product development.
PAEXS 20-Li A1
14 GBIE
Ordering a replacement battery
If you want to order a replacement battery for your appliance, you can do so easily via the Internet on
www.kompernass.com or by telephone.
Due to limited stocks, this item may sell out in a relatively short time.
NOTE
Online ordering of replacement parts might not be possible in some countries. In this is the case,
please contact the Service hotline.
Telephone ordering
Service Great Britain Tel.: 0800 404 7657
Service Ireland Tel.: 1890 930 034
(0,08 EUR/Min., peak · 0,06 EUR/Min., off peak)
To ensure fast processing of your order, have the article number of your appliance to hand
(e.g. IAN 351737) in case of questions. The article number can be found on the type plate
or the title page of these instructions.
PAEXS 20-Li A1 DEATCH 15
Inhaltsverzeichnis
Einleitung .............................................................16
Bestimmungsgemäßer Gebrauch .......................................................16
Ausstattung ........................................................................16
Lieferumfang .......................................................................16
Technische Daten ...................................................................16
Allgemeine Sicherheitshinweise für Elektrowerkzeuge .......................17
1. Arbeitsplatzsicherheit ..............................................................17
2. Elektrische Sicherheit ..............................................................17
3. Sicherheit von Personen ............................................................18
4. Verwendung und Behandlung desElektrowerkzeugs .....................................18
5. Verwendung und Behandlung desAkkuwerkzeugs .......................................19
6. Service .........................................................................20
Sicherheitshinweise für Ladegeräte .....................................................20
Gerätespezifische Sicherheits hinweise ...................................................20
Originalzubehör/-zusatzgeräte ........................................................21
Vor der Inbetriebnahme ................................................21
Akku-Pack laden (siehe Abb. A) ........................................................21
Akku-Pack ins Gerät einsetzen/entnehmen ...............................................22
Akkuzustand prüfen .................................................................22
Schleifblatt wählen ..................................................................22
Schleifblatt befestigen ...............................................................22
Staubabsaugung ...................................................................22
Fangbox zur Eigenabsaugung .........................................................23
Reduzierstück ......................................................................23
Inbetriebnahme .......................................................23
Zusatzhandgriff einstellen .............................................................23
Ein- und ausschalten .................................................................23
Drehzahl einstellen ..................................................................23
Arbeitshinweise. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Wartung und Reinigung .................................................24
Garantie der Kompernaß Handels GmbH ..................................24
Service ...............................................................26
Importeur ............................................................26
Entsorgung ...........................................................26
Original-Konformitätserklärung ..........................................27
Ersatz-Akku Bestellung .................................................28
Telefonische Bestellung ...............................................................28
PAEXS 20-Li A1
16 DEATCH
AKKU-EXZENTERSCHLEIFER
PAEXS 20-Li A1
Einleitung
Wir beglückwünschen Sie zum Kauf Ihres
neuen Gerätes. Sie haben sich damit für
ein hochwertiges Produkt entschieden.
Die Bedienungsanleitung ist Teil dieses Produkts.
Sie enthält wichtige Hinweise für Sicherheit, Ge-
brauch und Entsorgung. Machen Sie sich vor der
Benutzung des Produkts mit allen Bedien- und
Sicherheitshinweisen vertraut. Benutzen Sie das
Produkt nur wie beschrieben und für die angege-
benen Einsatzbereiche. Händigen Sie alle Unter-
lagen bei Weitergabe des Produkts an Dritte mit aus.
Bestimmungsgemäßer Gebrauch
Das Gerät ist – je nach Schleifpapier – zum
trockenen Schleifen von Holz, Kunststoff, Metall,
Spachtel masse sowie lackierten Oberflächen be-
stimmt. Jede andere Verwendung oder Verände-
rung des Gerätes gilt als nicht bestimmungsgemäß
und birgt erhebliche Unfallgefahren. Für aus be-
stimmungswidriger Verwendung entstandene
Schäden übernehmen wir keine Haftung. Nicht für
den gewerblichen Gebrauch bestimmt.
Ausstattung
EIN-/AUS-Schalter
Entriegelungstaste
Lasche (Fangbox)
Fangbox zur Eigenabsaugung
Reduzierstück zur Fremdabsaugung (zweiteilig)
Adapteranschluss
Schleifblatt
Schleifplatte
Schraube
Zusatzhandgriff
Drehzahl-Stellrad
Abbildung A
Akku-Display-LED
Taste Akkuzustand
Akku-Pack*
Schnellladegerät*
grüne Kontroll-LED
rote Kontroll-LED
Lieferumfang
1 Akku-Exzenterschleifer
4 Exzenterschleifblätter
(Körnung 60/80/120/240)
1 Fangbox
1 Reduzierstück zur Fremdabsaugung (zweiteilig)
1 Bedienungsanleitung
Technische Daten
Akku-Exzenterschleifer PAEXS 20-Li A1
Bemessungsspannung 20 V (Gleichstrom)
Bemessungs-
Leerlaufdrehzahl n0 3000–12000 min-1
Schleifblatt Ø 125 mm
Akku PAP 20 A1*
Typ LITHIUM-IONEN
Bemessungsspannung 20 V (Gleichstrom)
Kapazität 2 Ah
Zellen 5
Akku-Schnellladegerät PLG 20 A1*
EINGANG/Input
Bemessungsspannung 230–240 V ∼, 50 Hz
(Wechselstrom)
Bemessungsaufnahme 65 W
Sicherung (innen) 3,15 A T3.15A
AUSGANG/Output
Bemessungsspannung 21,5 V (Gleichstrom)
Bemessungsstrom 2,4 A
Ladedauer ca. 60 min
Schutzklasse II /
(Doppelisolierung)
* AKKU UND LADEGERÄT SIND NICHT IM
LIEFERUMFANG ENTHALTEN
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133

Parkside PAEXS 20-Li A1 Návod na používanie

Kategória
Elektrické náradie
Typ
Návod na používanie