Dometic RT780 for lveco Stralis AS/AS³ and AT (High roof) Návod na obsluhu

AIR CONDITIONERS

COOLAIR

RT780

Assembly kit for lveco Stralis AS/AS³

and AT (High roof)

Installation Manual . . . . . . . . . . . . . . . . . . 8

Montagesatz für lveco Stralis AS/AS³

und AT (Hochdach)

Montageanleitung . . . . . . . . . . . . . . . . . 24

Kit de montage pour lveco Stralis AS/

AS³ et AT (Toit élevé)

Instructions de montage. . . . . . . . . . . . . .41

Juego de montaje para lveco Stralis AS/

AS³ y AT (Techo alto)

Instrucciones de montaje . . . . . . . . . . . . 58

Kit de montagem para lveco Stralis AS/

AS³ e AT (teto alto)

Instruções de montagem . . . . . . . . . . . . 75

Set di montaggio per lveco Stralis AS/

AS³ e AT (Tetto alto)

Indicazioni di montaggio . . . . . . . . . . . . 92

Montageset voor lveco Stralis AS/AS³ en

AT (Hoogdak)

Montagehandleiding . . . . . . . . . . . . . . 109

Monteringssæt til lveco Stralis AS/AS³

og AT (Højt tag)

Monteringsvejledning . . . . . . . . . . . . . 126

Monteringssats för lveco Stralis AS/AS³

och AT (Högtak)

Monteringsanvisning . . . . . . . . . . . . . . 142

Monteringssett for lveco Stralis AS/AS³

og AT (Høyt tak)

Monteringsanvisning . . . . . . . . . . . . . . . 158

Asennussarja malleihin lveco Stralis AS/

AS³ ja AT (Korkeakattoinen)

Asennusohje . . . . . . . . . . . . . . . . . . . . . . 174

Монтажный комплект для

lveco Stralis AS/AS и AT (с высокой

крышей)

Инструкция по монтажу . . . . . . . . . . . . 190

Zestaw montażowy do lveco Stralis AS/

AS i AT (z podwyższonym dachem)

Instrukcja montażu . . . . . . . . . . . . . . . . .207

Montážna súprava pre lveco Stralis AS/

AS3 a AT (zvýšená strecha)

Návod na montáž . . . . . . . . . . . . . . . . . 224

Montážní sada pro vozidla

lveco Stralis AS/AS a AT (vysoká střecha)

Návod k montáži. . . . . . . . . . . . . . . . . . 240

Szerelőkészlet a következőkhöz:

lveco Stralis AS/AS³ és AT (magastető)

Szerelési útmutató . . . . . . . . . . . . . . . . 256

EN

DE

FR

ES

PT

IT

NL

DA

SV

NO

FI

RU

PL

SK

CS

HU

RT780-Iveco--I-16s.book Seite 1 Donnerstag, 6. Juli 2017 3:16 15

RT780-Iveco--I-16s.book Seite 2 Donnerstag, 6. Juli 2017 3:16 15

3

CoolAir RT780

276358

AS/AT: 166

AS³: 188

1

830

2

RT780-Iveco--I-16s.book Seite 3 Donnerstag, 6. Juli 2017 3:16 15

CoolAir RT780

4

1

4

3

4

RT780-Iveco--I-16s.book Seite 4 Donnerstag, 6. Juli 2017 3:16 15

5

CoolAir RT780

1

2

3

4

5

1

2

3

4

6

RT780-Iveco--I-16s.book Seite 5 Donnerstag, 6. Juli 2017 3:16 15

CoolAir RT780

6

134567

8

9

2

7

12

11

10

1

2

3

8

7

4 9

6

5

7

11

+24 V –/0 V

M

8

RT780-Iveco--I-16s.book Seite 6 Donnerstag, 6. Juli 2017 3:16 15

7

CoolAir RT780

bl br gl gr ro sw w

EN Blue Brown Yellow Green Red Black White

DE Blau Braun Gelb Grün Rot Schwarz Weiß

FR Bleu Marron Jaune Vert Rouge Noir Blanc

ES Azul Marrón Amarillo Verde Rojo Negro Blanco

PT Azul Castanho Amarelo Verde Cinzento Vermelho Preto

IT Blu Marrone Giallo Verde Rosso Nero Bianco

NL Blauw Bruin Geel Groen Rood Zwart Wit

DA Blå Brun Gul Grøn Rød Sort Hvid

SV Blå Brun Gul Grön Röd Svart Vit

NO Blå Brun Gul Grønn Rød Svart Hvit

FI Sininen Ruskea Keltainen Vihreä Punainen Musta Valkoinen

RU Синий Коричневый Желтый Зеленый Красный Черный Белый

PL Niebieski Brązowy Żółty Zielony Czerwony Czarny Biały

SK Modrá Hnedá Žltá Zelená Červená Čierna Biela

CS Modrá Hněda Žlutá Zelená Červená Černá Bílá

HU Kék Barna Sárga Zöld Piros Fekete Fehér

RT780-Iveco--I-16s.book Seite 7 Donnerstag, 6. Juli 2017 3:16 15

EN

CoolAir RT780

8

Contents

1 Symbols and formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.1 Using the device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

2.2 Handling electrical cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

3 Conventions in this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.1 General information on the installation manual . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.2 Target group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

4 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

5 Scope of delivery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

6 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

7 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

7.1 Notes on installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

7.2 Removing the sunroof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

7.3 Preparing unit fastening (Iveco Stralis AS³ only) . . . . . . . . . . . . . . . . . . . . . . . . . .15

7.4 Preparing the unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

7.5 Attaching the seal for the cab roof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

7.6 Installing the unit in the sunroof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

7.7 Installing the electrical supply lines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

7.8 Fastening the cover frame. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

8 Configuration of unit software . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

8.1 Starting and ending configuration mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

8.2 Menu level 1: Set temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

8.3 Menu level 2: Low voltage cut-off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

8.4 Menu level 3: Operating mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

8.5 Menu level 4: Default setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

8.6 Menu level 5: Temperature unit display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

9 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

RT780-Iveco--I-16s.book Seite 8 Donnerstag, 6. Juli 2017 3:16 15

9

EN

CoolAir RT780 Symbols and formats

1 Symbols and formats

!

A

I

2 Safety instructions

You must read the entire manual thoroughly and carefully.

We can only guarantee the reliability of the air conditioning roof unit if the

instructions are adhered to. The same applies to the prevention of injury and

damage to property.

The manufacturer accepts no liability for damage in the following cases:

• Faulty assembly or connection

• Damage to the product resulting from mechanical influences and excess

voltage

• Alterations to the product without express permission from the manufacturer

• Use for purposes other than those described in the operating manual

WARNING!

Safety instruction: Failure to observe this instruction can cause fatal or

serious injury.

CAUTION!

Safety instruction: Failure to observe this instruction can lead to injury.

NOTICE!

Failure to observe this instruction can cause material damage and impair the

function of the product.

NOTE

Supplementary information for operating the product.

RT780-Iveco--I-16s.book Seite 9 Donnerstag, 6. Juli 2017 3:16 15

EN

Safety instructions CoolAir RT780

10

2.1 Using the device

• The freedom of movement of semi-trailers (of the outer edges of the semi-

trailer when turning or jackknifing) and other vehicle attachments must not be

restricted.

• Only use the air conditioning roof unit for the purpose specified by the

manufacturer and do not make any alterations or structural changes to the

device.

• Do not use the air conditioning roof unit if it is visibly damaged.

• The air conditioning roof unit must be installed safely so that it cannot tip over

or fall down.

• Installation, maintenance and repair work may only be carried out by

qualified personnel from a specialist company who are familiar with the risks

involved and the relevant regulations.

• Do not use the air conditioning roof unit near flammable fluids and gases.

• Do not operate the air conditioning roof unit if the ambient temperature is

below 0 °C.

• Do not undo the upper cover of the air conditioning roof unit in the event of

a fire. Use approved extinguishing agents instead. Do not use water to extin-

guish fires.

• Please inform your vehicle manufacturer if the height entered in your vehicle

documents needs to be altered due to the installation of the air conditioning

roof unit.

– lveco Stralis AS/AT height: 166 mm.

– lveco Stralis AS³ height: 188 mm

• Disconnect all power supply lines when working on the air conditioning roof

unit (cleaning, maintenance, etc).

2.2 Handling electrical cables

• Use cable ducts to lay cables through walls with sharp edges.

• Do not lay loose or bent cables next to electrically conductive materials

(metal).

• Do not pull on the cables.

• Attach and lay the cables in such a manner that they cannot be tripped over

or damaged.

• The electrical power supply may only be connected by a specialist work-

shop.

• Fit a fuse of 25 amps to the connection to the vehicle's power supply.

• Never lay power supply lines (battery leads) in the vicinity of signal or control

cables.

RT780-Iveco--I-16s.book Seite 10 Donnerstag, 6. Juli 2017 3:16 15

11

EN

CoolAir RT780 Conventions in this manual

3 Conventions in this manual

3.1 General information on the installation manual

This installation manual contains the essential information and instructions for

installing the air conditioning roof unit. The information contained is orientated

towards the company installing the air conditioning roof unit.

The following instructions are intended to help you properly use the installation

manual:

• The installation manual is part of the scope of delivery and should be stored

carefully.

• The installation manual provides you with important information on the

installation of the device and can also be used as a reference material in the

event of repairs.

• The manufacturer assumes no liability for non-observance of this installation

manual. Any claims are excluded in this case.

3.2 Target group

The installation and configuration information in this manual is intended for

qualified installation personnel who are familiar with the guidelines and safety

precautions to be applied during the installation of lorry accessory parts.

4 Intended use

The installation kit (AS/AT: ref. no. 9100300104, AS³: ref. no. 9100300105) ena-

bles the installation of an air conditioning roof unit CoolAir RT780 (ref. no.

9105305547) in a roof ventilation opening (hatch) provided at the plant in a

lveco Stralis AS/AT (high roof) or lveco Stralis AS³ (high roof) driver cab.

A

I

NOTICE!

• The RT780 unit is not suitable for installation in construction machines,

agricultural machines or similar equipment. They will not work properly if

exposed to strong vibrations.

• Operating the RT780 unit with voltages other than those specified can

result in damage to the devices.

NOTE

The RT780 unit is only designed for ambient temperatures of up to 43 °C.

RT780-Iveco--I-16s.book Seite 11 Donnerstag, 6. Juli 2017 3:16 15

EN

Scope of delivery CoolAir RT780

12

5 Scope of delivery

CoolAir RT780 installation kit for lveco Stralis AS/AT,

ref. no. 9100300104

CoolAir RT780 installation kit for lveco Stralis AS³,

ref. no. 9100300105

6 Accessories

Available as accessories (not included in the scope of delivery):

Part designation Quantity Ref. no.

Installation manual 1 4445102177

Cover frame 1 4443000260

2.5 m insulating tape (profile: 10 x 20 mm) 1 –

Spacer sleeve L = 18 mm, ∅ 14 mm 12 4443900236

Hex screw M8 x 45 12 –

Washer 8.4 x 20 12 –

Spring washer M8 12 –

Connection cable 6 mm² x 4 m 1 4441300149

Cable binder 1 –

Part designation Quantity Ref. no.

Installation manual 1 4445102177

Cover frame 1 4443000260

2.5 m insulating tape (profile: 35 x 20 mm) 1 –

Spacer sleeve L = 40 mm 12 4443900237

Hex screw M8 x 65 12 –

Washer 8.4 x 20 12 –

Spring washer M8 12 –

Connection cable 8 mm² x 9.5 m 1 4441300097

Cable binder 1 –

Part designation Ref. no.

Connection cable 8 mm² x 11 m 9100300027

RT780-Iveco--I-16s.book Seite 12 Donnerstag, 6. Juli 2017 3:16 15

13

EN

CoolAir RT780 Installation

7 Installation

A

7.1 Notes on installation

These installation instructions must be read completely prior to the installation of

the air conditioning roof unit.

The following tips and instructions must be observed wile installing the air con-

ditioning roof unit:

!

• Always check whether any vehicle components could be damaged or their

operation impaired by the unit before installing the air conditioning roof unit.

You can use fig. 1, page 3 and fig. 2, page 3 to check the dimensions of

the installed unit. The dotted line indicates the middle of the sunroof open-

ing.

• Before installation, find out (by consulting the manufacturer of the vehicle)

whether the construction is designed for the static weight and the loads of

the parking cooler when the vehicle is in motion. The manufacturer of the air

conditioning roof unit assumes no liability whatsoever.

• The roof inclination of the mounting surface may not exceed 20° in the

direction of travel.

• The supplied assembly parts must not be modified during installation.

• The ventilation slots (grill) may not be covered (minimum distance from other

attachment parts: 10 cm).

• You can connect the unit to the battery via the lorry's terminal block or

directly. The terminal block is to be preferred for the connection. On some

vehicles, larger consumers connected to the terminal block are switched off

after a short while if the power requirement is too high. Ask your vehicle

manufacturer for the specifications of the terminal block.

NOTICE!

• The air conditioning roof unit may only be installed by qualified personnel

from a specialist company. The following information is intended for

technicians who are familiar with the guidelines and safety precautions to

be applied.

• The manufacturer only assumes liability for parts included in the scope of

delivery. The validity of the warranty expires if the device is installed

together with third-party parts.

• Check whether the roof of the vehicle is able to support the weight of a

person before climbing onto it. Ask the vehicle manufacturer about the

permitted roof loads.

WARNING!

Make sure that all electrical components are electrically discharged before

carrying out work on them!

RT780-Iveco--I-16s.book Seite 13 Donnerstag, 6. Juli 2017 3:16 15

EN

Installation CoolAir RT780

14

• When installing the system and making the electrical connections, observe

the guidelines from the body manufacturer.

• Pay attention to the connection plan for the device:

!

I

No. in

fig. 8, page 6

Designation

1Control pad

2 Connection cable

3 Room temperature sensor

4Earth

5 Klickson (compressor)

6Compressor

7Condenser fan

8Vaporiser fan

9Earth

10 25 A fuse

11 2 A fuse

12 4 A fuse

WARNING!

Before installing the air conditioning roof unit, all connections to the battery of

the vehicle must be disconnected.

Non-observance of this regulation can result in danger of electrocution.

CAUTION!

Improper installation of the air conditioning roof unit can result in irreparable

damage to the device and put the safety of the user at risk.

The manufacturer will not be held liable for claims if the air conditioning roof

unit is not installed according to this installation manual. That applies to mal-

functions and the safety of the air conditioning roof unit, in particular to injuries

and damage to property.

NOTE

After installing the unit, the specified parameters of the unit software must be

checked (chapter “Configuration of unit software” on page 18).

RT780-Iveco--I-16s.book Seite 14 Donnerstag, 6. Juli 2017 3:16 15

15

EN

CoolAir RT780 Installation

7.2 Removing the sunroof

➤ Remove all screws and fixtures of the existing sunroof.

➤ Take out the sunroof.

➤ Remove the sealant around the opening, so that the surface is clean and free

of grease.

I

7.3 Preparing unit fastening (Iveco Stralis AS³ only)

➤ Enlarge the 12 existing ∅ 6.5 mm holes for fastening the sunroof to a

diameter of 8.5 mm.

7.4 Preparing the unit

A

➤ Place the air conditioning roof unit on a work surface with the housing facing

down.

A

➤ Screw in the 12 self-threading M8 thread inserts in the blind holes marked

with “1” and “4” (fig. 3, page 4).

Use the supplied 1/4" bit for this.

NOTE

Dispose of all waste material, glue, silicone and seals separately. Observe the

local disposal guidelines.

NOTICE!

During preparatory work on the surfaces, secure the unit from falling down.

Make sure that the work surface is clean and level to ensure that the unit is not

damaged.

NOTICE!

Screw in the thread insert vertically.

Do not exceed the screw torque of 10 Nm.

RT780-Iveco--I-16s.book Seite 15 Donnerstag, 6. Juli 2017 3:16 15

EN

Installation CoolAir RT780

16

7.5 Attaching the seal for the cab roof

A

➤ Stick the 2.5 m insulating tape to the cab roof, following the outline of the

sunroof (fig. 4, page 4):

– RT780 lveco Stralis AS/AT: insulating tape 10 x 20 mm

– RT780 lveco Stralis AS³: insulating tape 35 x 20 mm

➤ Provide the abutting edge and the top edge of the insulating tape with an

unhardened plastic butyl sealing compound (e.g. SikaLastomer-710).

7.6 Installing the unit in the sunroof

➤ Set the unit down centrally aligned and in the direction of travel (fig. 1,

page 3) on the sunroof opening.

I

➤ Position the spacer sleeve (fig. 6 1, page 5) on the fixing drill holes as

shown in fig. 6, page 5.

– RT780 lveco Stralis AS/AT: spacer sleeve L = 18 mm

– RT780 lveco Stralis AS³: spacer sleeve L= 40 mm

➤ Screw one hex screw (fig. 6 4, page 5) with washer (fig. 6 2, page 5) and

spring washer (fig. 6 3, page 5) into each of the 12 thread inserts on the

underside of the unit.

– RT780 lveco Stralis AS/AT: hex screw M8 x 45 mm

– RT780 lveco Stralis AS³: hex screw M8 x 65 mm

A

➤ Tighten the screws with a torque of 8 Nm.

NOTICE!

Ensure that the adhesive surface for the seal between the unit and the cab roof

is clean (free of dust, oil, etc.).

NOTE

Make sure the air conditioning roof unit is centred perfectly. The seal must be

applied continuously around the air conditioning roof unit after being placed

on the roof of the vehicle. This is the only way to ensure a tight seal.

NOTICE!

Do not exceed the specified torque under any circumstances. This is the only

way to ensure that the thread inserts are not torn out.

RT780-Iveco--I-16s.book Seite 16 Donnerstag, 6. Juli 2017 3:16 15

17

EN

CoolAir RT780 Installation

7.7 Installing the electrical supply lines

!

A

I

lveco Stralis AS/AT: You can connect the unit to the battery via the lorry's

terminal block or directly. The terminal block is to be preferred for the connec-

tion. Ask your vehicle manufacturer for the specifications of the terminal block.

lveco Stralis AS³: You can connect the unit to the battery via the lorry's terminal

block or directly. Here, the connection directly to the battery should be pre-

ferred, as the consumer which is connected to the terminal block switches off

after approx. 10 min if there is a high power requirement.

➤ Lay the supply line and connect it to the vehicle (red line to plus, black line to

minus).

➤ Plug in the supply line plug into the socket of the air conditioning roof unit

supply line.

➤ To relieve strain on the supply line, secure it with a cable tie, e.g. to the cab

roof.

WARNING!

• The electrical power supply may only be performed by qualified personnel

with specialist knowledge.

• Make sure there is no voltage present on electrically operated components

before carrying out work on them!

NOTICE!

• Fit a fuse of 25 amps to the connection to the vehicle's power supply.

• The battery must be able to supply the required current and voltage

(chapter “Technical data” on page 23).

NOTE

The unit is equipped as standard with:

• lveco Stralis AS/AT: a 4 m long cable with a cross-section of 6 mm

2

• lveco Stralis AS³: a 9.5 m long cable with a cross-section of 8 mm

2

If longer cable lengths are required, then the cable cross-section must be

increased by an authorised specialist workshop:

In this case cut off the cable as closely as possible to the unit (max. 0.5 m) and

then establish a suitable connection with a larger cable cross-section.

The manufacturer recommends:

• Iveco Stralis AS/AT: when the cable is extended by 4 m to 6 m in length,

use a cross-section of at least 8 mm

2

.

• Iveco Stralis AS/AT: when the cable is extended by 9 m to 11 m in length,

use a cross-section of at least 10 mm

2

.

RT780-Iveco--I-16s.book Seite 17 Donnerstag, 6. Juli 2017 3:16 15

EN

Configuration of unit software CoolAir RT780

18

7.8 Fastening the cover frame

A

➤ Fasten the cover frame (fig. 5 5, page 5) the same way as for the original

frame for the sliding roof.

8 Configuration of unit software

Before you first start up the unit, the controls can be adapted to suit the

installation conditions. This must be done by the person installing the unit.

In configuration mode, the following unit software parameters must be set at the

control panel (fig. 7, page 6).

I

NOTICE!

Screw the screws in carefully order not to damage the cover frame.

Menu

level

Parameter Meaning

Default

setting

1 Set temperature The unit starts at the temperature

defined here.

20 °C (68 °F)

2Low voltage

cut-off

The battery monitor shuts down the unit

at the voltage defined here.

Characteristic

figure 4 =

22,8 V

3 Operating mode The unit starts with the operating mode

defined here.

0 = Auto-

matic mode

4 Default settings Parameters 1 – 3 can be reset to the

default settings.

--

5Temperature unit

display

The temperature can be displayed in °C

or °F.

°C

NOTE

Configuration mode can still be activated if the undervoltage protection

mechanism has switched off the unit and only residual voltage is available.

RT780-Iveco--I-16s.book Seite 18 Donnerstag, 6. Juli 2017 3:16 15

19

EN

CoolAir RT780 Configuration of unit software

8.1 Starting and ending configuration mode

The adjustable parameters can be changed in configuration mode:

➤ When using the button to switch on the unit, hold both buttons +

and

–

pressed until the compressor LED flashes.

✓ You are now in configuration mode.

✓ The display version (e. g. “3.1S”) appears in the display for 2 seconds.

✓ The first digit of the display shows the menu level and the second and third

digits show the parameters which can be set, e.g.

1.17 for menu level 1 and a

set target value of 17 °C.

I

➤ Press the button to quit configuration mode.

8.2 Menu level 1: Set temperature

The unit always starts with a defined value for the room temperature. This

parameter can be configured between 17 and 30 °C (62 and 86 °F).

➤ Start configuration mode (chapter “Starting and ending configuration mode”

on page 19).

✓ The first digit of the display shows the menu level and the second and third

show the parameter which can be set.

➤ Press the button to change the parameters.

➤ Use the +

and

–

buttons

to select the target value (in °C) at which the unit

should start operation.

✓ The digits in the display flash until the parameter you entered is confirmed.

➤ Press the button to confirm your entry.

✓ The set value is saved and is then used when the unit is restarted.

✓ You are now in menu level 1 again and can use the +

and

– buttons to switch

between menu levels.

NOTE

If you make no entry on the control panel for 60 seconds, the unit quits

configuration mode and shuts down.

RT780-Iveco--I-16s.book Seite 19 Donnerstag, 6. Juli 2017 3:16 15

EN

Configuration of unit software CoolAir RT780

20

8.3 Menu level 2: Low voltage cut-off

The battery monitor protects the battery from excessive discharging.

A

If only the set power supply is available here for the air conditioning roof unit, the

unit is switched off.

➤ Start configuration mode (chapter “Starting and ending configuration mode”

on page 19).

✓ The first digit of the display shows the menu level and the second and third

show the parameter which can be set.

➤ Press the

+

button

once to switch to menu level

2

.

➤ Press the button to change the parameter.

✓ The digits in the display flash until the parameter you entered is confirmed.

➤ Use the +

and

–

buttons

to set the value for low voltage shutdown. The

characteristic figures at second and third place on the display represent the

voltage (V) at which the unit is shut down:

➤ Press the button to confirm your entry.

✓ The set value is saved and is then used when the unit is restarted.

✓ You are now in menu level 2 again and can use the +

and

– buttons to switch

between menu levels.

NOTICE!

When the battery monitor switches the device off, the battery only has part of

its charging capacity. Avoid starting repeatedly or operating electrical consum-

ers. Make sure that the battery is recharged. As soon as the required voltage is

available again, the unit can be operated again.

Characteristic

figure

Low voltage

shutdown

Characteristic

figure

Low voltage

shutdown

1 22.2 6 23.0

2 22.4 7 23.1

3 22.6 8 23.2

4 22.8 9 23.4

5 22.9 10 23.6

RT780-Iveco--I-16s.book Seite 20 Donnerstag, 6. Juli 2017 3:16 15

Stránka sa načítava ...

Dometic RT780 for lveco Stralis AS/AS³ and AT (High roof) Návod na obsluhu

Táto príručka je tiež vhodná pre

Dometic RT780 for lveco Stralis AS/AS³ and AT (High roof) Návod na obsluhu

V iných jazykoch

Súvisiace články