Stránka sa načítava...
DSP1312T, DSP1324T, DSP1812T, DSP1824T,
DSP2312T, DSP2324T, DSP3512T, DSP3524T
Sine wave inverter
Installation and Operating Manual. . . . . . . . 3
Sinus-Wechselrichter
Montage- und Bedienungsanleitung . . . . .27
Onduleur sinusoïdal
Instructions de montage
et de service . . . . . . . . . . . . . . . . . . . . . . . . .52
Convertidor de ondas seno
Instrucciones de montaje y de uso . . . . . . .76
Conversor sinusoidal
Instruções de montagem e manual de
instruções . . . . . . . . . . . . . . . . . . . . . . . . . .100
Inverter sinusoidale
Istruzioni di montaggio e d’uso . . . . . . . . 124
Sinus ondulator
Montagehandleiding en
gebruiksaanwijzing . . . . . . . . . . . . . . . . . .149
Sinus ensretter
Monterings- og betjeningsvejledning . . . 173
Sinus växelriktare
Monterings- och bruksanvisning . . . . . . . 195
Sinus vekselretter
Monterings- og bruksanvisning. . . . . . . . 217
Sinus -vaihtosuuntaaja
Asennus- ja käyttöohje . . . . . . . . . . . . . . . 239
Синусоидальный инвертор
Инструкция по монтажу и эксплуатации 261
Przetwornica sinusoidalna
Instrukcja montażu i obsługi. . . . . . . . . . . 286
Sínusový menič napätia
Návod na montáž a uvedenie
do prevádzky. . . . . . . . . . . . . . . . . . . . . . . 310
Sinusový měnič
Návod k montáži a obsluze . . . . . . . . . . . 334
Szinuszos inverter
Szerelési és használati útmutató . . . . . . . 356
OU
TPU
T
INPU
T
S
T
A
TU
S
S4
S3
S2
S
1
B
R
E
A
KER
T
N
I
T
L
N
B
L
N
A
O
U
TP
U
T
I
N
P
UT
EN
DE
FR
ES
PT
IT
NL
DA
SV
NO
FI
RU
PL
SK
CS
HU
ENERGY & LIGHTING
SINEPOWER
DSP1300T-3500T--IO-16s.book Seite 1 Dienstag, 27. November 2018 4:39 16
DSP1300T-3500T--IO-16s.book Seite 2 Dienstag, 27. November 2018 4:39 16
EN
SinePower
3
Please read this instruction manual carefully before installation and first
use, and store it in a safe place. If you pass on the product to another
person, hand over this instruction manual along with it.
Table of contents
1 Explanation of symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
2 General safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
3 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
4 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
5 Target group for this manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
6 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
7 Technical description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
8 Fitting the inverter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
9 Connecting the inverter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
10 Using the inverter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
11 Cleaning and caring for the inverter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
12 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
13 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
14 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
15 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
DSP1300T-3500T--IO-16s.book Seite 3 Dienstag, 27. November 2018 4:39 16
EN
Explanation of symbols SinePower
4
1 Explanation of symbols
D
!
A
I
2 General safety instructions
2.1 General safety
The manufacturer accepts no liability for damage in the following cases:
• Faulty assembly or connection
• Damage to the product resulting from mechanical influences and incorrect
connection voltage
• Alterations to the product without express permission from the manufacturer
• Use for purposes other than those described in the operating manual
Note the following basic safety information when using electrical devices to protect
against:
• Electric shock
•Fire hazards
•Injury
DANGER!
Safety instruction: Failure to observe this instruction will cause death
or serious injury.
WARNING!
Safety instruction: Failure to observe this instruction can cause death
or serious injury.
NOTICE!
Failure to observe this instruction can cause material damage and impair
the function of the product.
NOTE
Supplementary information for operating the product.
DSP1300T-3500T--IO-16s.book Seite 4 Dienstag, 27. November 2018 4:39 16
EN
SinePower General safety instructions
5
2.2 General safety
D
DANGER!
• In the event of fire, use a fire extinguisher which is suitable for electrical
devices.
!
WARNING!
• Only use the device as intended.
• Ensure that the red and black terminals never come into contact.
• Disconnect the device from the mains:
– Before cleaning and maintenance
• If you disassemble the device:
– Detach all connections
– Make sure that no voltage is present at any of the inputs and out-
puts
• The device may not be used if the device itself or the connection cable
are visibly damaged.
• If this power cable for this device is damaged, it must be replaced by
the manufacturer, customer service or a similarly qualified person in
order to prevent safety hazards.
• This device may only be repaired by qualified personnel. Inadequate
repairs may cause serious hazards.
• This device can be used by children aged 8 years or over, as well as by
persons with diminished physical, sensory or mental capacities or a
lack of experience and/or knowledge, providing they are supervised
or have been taught how to use the device safely and are aware of the
resulting risks.
• Electrical devices are not toys.
Always keep and use the appliance out of the reach of children.
• Children must be supervised to ensure that they do not play with the
device.
A
NOTICE!
• Before start-up, check that the voltage specification on the type plate
is the same as that of the power supply.
• Ensure that other objects cannot cause a short circuit at the contacts
of the device.
• Never pull the plug out of the socket by the connection cable.
• Store the device in a dry and cool place.
DSP1300T-3500T--IO-16s.book Seite 5 Dienstag, 27. November 2018 4:39 16
EN
General safety instructions SinePower
6
2.3 Safety when installing the device
D
DANGER!
• Never mount the device anywhere where there is a risk of gas or dust
explosion.
!
CAUTION!
• Ensure that the device is standing firmly.
The device must be set up and fastened in such a way that it cannot tip
over or fall down.
A
NOTICE!
• Do not expose the device to a heat source (such as direct sunlight or
heating). Avoid additional heating of the device in this way.
• Set up the device in a dry location where it is protected against splash-
ing water.
2.4 Safety when connecting the device electronically
D
DANGER! Danger of electrocution
• If you are working on electrical systems, ensure that there is somebody
close at hand who can help you in emergencies.
!
WARNING!
• Make sure that the lead has a sufficient cross-section.
• Lay the cables so that they cannot be damaged by the doors or the
bonnet.
Crushed cables can lead to serious injury.
!
CAUTION!
• Lay the cables so that they cannot be tripped over or damaged.
DSP1300T-3500T--IO-16s.book Seite 6 Dienstag, 27. November 2018 4:39 16
EN
SinePower General safety instructions
7
A
NOTICE!
• Use ductwork or cable ducts if it is necessary to lay cables through
metal panels or other panels with sharp edges.
•Do not lay the 230 V mains cable and the 12 V DC cable in the same
duct.
•Do not lay the cable so that it is loose or heavily kinked.
• Fasten the cables securely.
• Do not pull on the cables.
2.5 Operating the device safely
D
DANGER! Danger of electrocution
• Do not touch exposed cables with your bare hands.
!
WARNING!
• Only use the device in closed, well-ventilated rooms.
!
CAUTION!
•Do not operate the device
– In salty, wet or damp environments
– In the vicinity of corrosive fumes
– In the vicinity of combustible materials
– In areas where there is a danger of explosions.
• Before starting the device, ensure that the power supply line and the
plug are dry.
• Always disconnect the power supply when working on the device.
• Please observe that parts of the device may still conduct voltage even
if the fuse has blown.
• Do not disconnect any cables when the device is still in use.
A
NOTICE!
• Make sure the air inlets and outlets of the device are not covered.
• Ensure good ventilation.
DSP1300T-3500T--IO-16s.book Seite 7 Dienstag, 27. November 2018 4:39 16
EN
Scope of delivery SinePower
8
3Scope of delivery
4Accessories
5 Target group for this manual
The electrical installation (chapter “Connecting the inverter” on page 14) is intended
for professionals who are familiar with the applicable regulations of the country in
which the equipment is to be installed and/or used.
All other chapters are intended for the users.
No. in
fig. 1
Designation
1 Sine wave inverter
2 DSP13xxT, DSP18xxT, DSP23xxT only
Connection cable with safety coupling (for 230 Vw output)
3 DSP13xxT, DSP18xxT, DSP23xxT only
Connection cable with safety plug (for 230 Vw supply)
– Operating manual
Designation Ref. no.
Remote control 9600002564
Energy monitor 9600002565
DSP1300T-3500T--IO-16s.book Seite 8 Dienstag, 27. November 2018 4:39 16
EN
SinePower Intended use
9
6 Intended use
!
The wave inverter converts direct current into a 230 – 240 V AC supply of 50 Hz or
60 Hz:
• 12 Vg: DSP1312T, DSP1812T, DSP2312T, DSP3512T
• 24 Vg: DSP1324T, DSP1824T, DSP2324T, DSP3524T
7 Technical description
The inverters can be operated wherever a DC connection is available:
• 12 Vg: DSP1312T, DSP1812T, DSP2312T, DSP3512T
• 24 Vg: DSP1324T, DSP1824T, DSP2324T, DSP3524T
The light-weight and compact construction of this device allows for easy installation
in mobile homes, commercial vehicles or motor and sailing yachts.
The output voltage corresponds to the household voltage from the socket (pure sine
wave, THD < 3 %).
Please observe the values for constant output power and peak output power as
indicated in chapter “Technical data” on page 23. Never connect devices that have
a higher power requirement.
I
The inverter has various protective mechanisms.
• Overvoltage shutdown: The inverter shuts itself off when the input voltage
exceeds the cut-off value. It restarts when the voltage returns to the restart value.
• Undervoltage shutdown: The inverter shuts itself off when the input voltage
falls below the cut-off value. It restarts when the voltage rises to the restart value.
• Excess temperature shutdown: The inverter switches off when the tempera-
ture inside the device or the temperature on the cooling element exceeds a cut-
off value. It restarts when the temperature falls below the restart value.
WARNING!
Never use the inverter on vehicles where the positive terminal of the
battery is connected to the chassis.
NOTE
Note when connecting devices with an electrical drive (such as power
drills and refrigerators), that they often require more power than is
indicated on the type plate.
DSP1300T-3500T--IO-16s.book Seite 9 Dienstag, 27. November 2018 4:39 16
EN
Technical description SinePower
10
• Overloading of the mains priority circuit and short circuit shutdown:
The LED on the inverter indicates an operating fault when an excess load is
connected or a short circuit has occurred. The fuse in the device must be pressed
in again by hand after it is triggered by excess current.
I
The inverter can be operated in the following net configurations:
• TN network:
The neutral conductor of the inverter is grounded. A downstream safety switch
(RCD) must be installed.
• IT network:
Both phases are insulated. This is suitable for operating one load. If more than
one load will be connected a protection plan has to be set up (e. g. insulation
monitor).
The network configuration is set via a DIP switch at the device.
The inverters DSP13xxT, DSP18xxT, DSP23xxT have a connection cable with socket
and plug. The inverter DSP35xxT is directly connected at the terminals via the PG
glands.
Due to the phase synchronisation the inverter adapts to the phase of the AC input
voltage. Thereby voltage peaks are prevented when switching from battery to
mains.
The inverter is suitable for operating sensitive consumers because the output voltage
is a pure sinus wave.
The inverter is fitted with a priority circuit. If an external 230 Vw voltage is available,
this will have priority. If no external 230 Vw voltage is connected, then the con-
nected battery will be used as the power supply.
The inverter can be switched to an energy-saving mode to prevent the connected
battery from discharging too quickly.
The inverter can be turned on or off using the remote control (accessory).
Additionally, the inverter can be controlled using the energy monitor (accessory).
NOTE
The individual values are found in the chapter “Technical data” on
page 23.
DSP1300T-3500T--IO-16s.book Seite 10 Dienstag, 27. November 2018 4:39 16
EN
SinePower Technical description
11
7.1 Control elements
No. in
fig. 2
Description Description
1 Main switch 0: Switches the device permanently off
I: Switches the device permanently on
II: The device can be switched on or off via a
remote control (accessory)
2 Status LED See chapter “Status indications” on page 18
3 Fuse Protects the inverter from overload.
The fuse can be pressed in again once it has
triggered.
4 Switch Sets the net configuration
5 Dip switch Makes settings on the inverter
See chapter “Configuring the inverter” on
page 19
DSP1300T-3500T--IO-16s.book Seite 11 Dienstag, 27. November 2018 4:39 16
EN
Fitting the inverter SinePower
12
7.2 Connections
I
8 Fitting the inverter
I
8.1 Tools required
For the electrical connection you will need the following tools:
•Crimping tool
• 3 multi-coloured, flexible connection cables. Determine the necessary thickness
from the table in chapter “Connecting the inverter” on page 14.
• Cable lugs and conductor sleeves
For fastening you will require the following tools:
• Machine bolts (M4) with washers and self-locking nuts or
• self-tapping screws or wood screws.
NOTE
The version for continental Europe is depicted.
No. in
fig. 2
Description
6 AC input (DSP35xxT: PG fitting)
7 AC output (DSP35xxT: PG fitting)
8 Ground terminal (Earthing on the vehicle bodywork)
9 Positive terminal
10 Negative terminal
11 CI/LIN BUS connections (LINA)
12 Remote control connection (LINB)
13 Connection of remote switch
14 Fan (backside)
NOTE
Before fitting the inverter, you should connect all cables because all
connections are freely accessible.
DSP1300T-3500T--IO-16s.book Seite 12 Dienstag, 27. November 2018 4:39 16
EN
SinePower Fitting the inverter
13
8.2 Mounting instructions
When selecting the installation location, observe the following instructions:
• The inverter can be mounted horizontally or vertically.
• The inverter must be installed in a place that is protected from moisture.
• The inverter may not be installed in the presence of flammable materials.
• The inverter may not be installed in a dusty environment.
• The place of installation must be well ventilated. A ventilation system must be
available for installations in small, enclosed spaces. The minimum clearance
around the inverter must be at least 5 cm (fig. 3).
• The ventilation holes on the front and back of the inverter must remain clear.
• For ambient temperatures higher than 40 °C (such as in engine or heating
compartments, or direct sunlight), the inverter may shut down although the
connected load is below the rated load (derating).
• The device must be installed on a level and sufficiently sturdy surface.
A
8.3 Mounting the inverter
➤ Mount the inverter as shown (fig. 4).
NOTICE!
Before drilling any holes, make sure that no electrical cables or other
parts of the vehicle can be damaged by drilling, sawing and filing.
DSP1300T-3500T--IO-16s.book Seite 13 Dienstag, 27. November 2018 4:39 16
EN
Connecting the inverter SinePower
14
9 Connecting the inverter
9.1 General instructions
!
• When installed in vehicles or boats, the inverter must be connected to the chassis
or earth.
• When setting up a socket distribution circuit (mains setup), comply with the
applicable regulations.
• Only use copper cables.
• Keep the cables as short as possible (< 1 m).
• For grounding use a cable with a minimum cross section of 4 mm².
• Keep to the specified cable cross section and fit a cable fuse (fig. 6 1) as close
to the battery as possible on the positive cable (see the table).
WARNING!
• The inverter may only be connected by a qualified workshop. The
following information is intended for technicians who are familiar
with the guidelines and safety precautions to be applied.
• Never use the inverter on vehicles where the positive terminal of the
battery is connected to the chassis.
• If you do not fit a fuse to the positive cable, the cables can over-
load, which might result in a fire.
Device
Required cable
cross section
Cable fuse
DSP1312T 35 mm² 200 A
DSP1324T 25 mm² 150 A
DSP1812T 50 mm² 250 A
DSP1824T 25 mm² 150 A
DSP2312T 70 mm² 300 A
DSP2324T 35 mm² 200 A
DSP3512T 2 x 50 mm² 2 x 250 A
DSP3524T 50 mm² 250 A
DSP1300T-3500T--IO-16s.book Seite 14 Dienstag, 27. November 2018 4:39 16
EN
SinePower Connecting the inverter
15
9.2 Connecting the inverter
!
A
I
➤ Connect the inverter as shown:
– Connecting the battery: fig. 5 and fig. 6
– Connecting the ground terminal fig. 7
– Connecting the 230 V power cable: fig. 8 (INPUT)
– Connecting the 230 V output cable: fig. 8 (OUTPUT)
9.3 Connecting multiple appliances
The device is equipped at delivery with galvanic isolation. For the safe operation of
multiple appliances, it is essential that a circuit breaker (residual current circuit
breaker) is built into the socket distribution circuit.
➤ Install a residual current circuit breaker in the socket distribution circuit.
➤ Set the inverter‘s net configuration to “TN grid” (chapter “Setting net configura-
tion” on page 20).
➤ Check the inverter‘s output concerning:
– correct voltage
– phase conductor
–neutral conductor
– protective conductor
WARNING!
Before connecting the AC output cable, make sure the inverter is
switched off at the main switch.
NOTICE!
Make sure that you do not reverse the polarity. Incorrect polarity can
damage the inverter.
NOTE
Tighten the nuts and bolts to a maximum torque of 15 Nm. Loose
connections may cause overheating.
DSP1300T-3500T--IO-16s.book Seite 15 Dienstag, 27. November 2018 4:39 16
EN
Connecting the inverter SinePower
16
9.4 Connecting the remote control (accessory)
A
➤ Connect the remote control as shown (fig. 9).
9.5 Connecting external switch to turn device on and off
I
You can use the following as an external switch:
• External switch, voltage supply from the inverter: fig. 0 A
• Control unit with relay or transistor circuit (TR): fig. 0 B
• External switch with voltage supply from the battery (BAT) of the vehicle:
fig. 0 C
• External switch with its own voltage supply (DC POWER) e.g. from the ignition:
fig. 0 D
➤ Set the main switch (fig. 2 1) to “OFF”.
➤ Make sure that the connection for the remote control (fig. 2 12) is not assigned.
➤ Set the main switch (fig. 2 1) to “REMO.”.
➤ Connect the external on/off switch with the connection cable to the terminal
(fig. 2 13).
NOTICE!
Only plug in the connection to the remote control in the remote port.
The device can be damaged by connecting it incorrectly.
NOTE
Use cables with a cable cross section of 0.25 – 0.75 mm².
DSP1300T-3500T--IO-16s.book Seite 16 Dienstag, 27. November 2018 4:39 16
EN
SinePower Using the inverter
17
9.6 Connecting the fault display relay
You can install a relay which monitors whether the 230 V input is connected.
Thereby you can, for example, implement an immobiliser so that the vehicle cannot
be started when the 230 V input is connected.
➤ Connect the relay as shown (fig. a):
– NO: normally open contact
– COM: common contact
– NC: normally closed contact
Relay specification:
10 Using the inverter
10.1 Switching on the inverter
➤ Set the main switch (fig. 2 1) of the inverter as follows:
–“0”: to switch the inverter permanently off
–“I”: to switch the inverter permanently on
–“II”: to switch the inverter on and off with a remote control (accessory)
➤ The inverter performs a self-test when starting.
✓ After the self-test is completed successfully, the LED lights up blue (fig. 2 2).
Maximum voltage Load
Current consumption
NO NC
250 Vw Ohmic 0.5 A 0.5 A
12 V/24 Vg Ohmic 1 A 1 A
DSP1300T-3500T--IO-16s.book Seite 17 Dienstag, 27. November 2018 4:39 16
EN
Using the inverter SinePower
18
10.2 Status indications
The blue LED (fig. 2 2) shows the operating condition of the inverter.
The inverter switches off if:
• The battery voltage drops below 10 V (12 Vg connection) or
20 V (24 Vg connection).
• The battery voltage exceeds 16.5 V (12 Vg connection) or
33 V (24 Vg connection).
• The inverter is overloaded.
• The inverter overheats.
➤ If this happens, shut down the inverter with the main switch (fig. 2 1).
➤ Check that the inverter is sufficiently ventilated and that the ventilation grilles are
unimpeded.
➤ Wait 5 – 10 minutes and switch the inverter on again without any electric
consumers.
10.3 Switching to energy-saving mode
I
Display Input voltage
Constantly lit Normal mode
Long flash, short interruption Inverter overheated/Overload
Quick flash Overvoltage/Undervoltage
Off Other fault
NOTE
The energy-saving mode can be set with a remote control only.
DSP1300T-3500T--IO-16s.book Seite 18 Dienstag, 27. November 2018 4:39 16
EN
SinePower Using the inverter
19
10.4 Configuring the inverter
You can adjust the device using the DIP switch (fig. 2 5).
Defining settings
Using the S1 dip switch you can define whether the parameter of the setting should
be made using the connection of a CI BUS capable control panel or the dip switches.
Setting the mains voltage
You can set the mains voltage using the S2 dip switch.
Dip switch
Parameter S1
Remote control connection Off
Dip switch On
DIP switch
Mains voltage S2
230V/50Hz Off
240 V/60 Hz On
DSP1300T-3500T--IO-16s.book Seite 19 Dienstag, 27. November 2018 4:39 16
EN
Using the inverter SinePower
20
Switching to energy-saving mode
You can set the energy-saving mode using the S3 and S4 dip switches. In this way,
the battery you connect to the inverter is not discharged as quickly.
The inverter operates in energy-saving mode as long as the required power is below
the set level. If the required power exceeds the set level, the inverter works in normal
mode.
The values to be set on your inverter can be found in the following table:
Setting net configuration
Using the switch (fig. 2 4) you can define in which net configuration the inverter
shall operate.
Energy-saving mode
DIP switch
S3 S4
Saving mode activated when load < 1 W
Normal mode activated when load > 1 W
Off Off
Saving mode activated when load < 1 W
Inverter shuts automatically down after operation
20 min in saving mode
Normal mode activated when load > 1 W
Off On
Saving mode activated when load < 45 W
Normal mode activated when load > 45 W
On Off
Saving mode activated when load < 45 W
Inverter shuts automatically down after operation
20 min in saving mode
Normal mode activated when load > 45 W
On On
Dip switch
Parameter S5
TN grid
An external downstream circuit breaker (RCD) is
necessary.
Off
IT grid
Operation with one load only or installation of an
external insulation monitor.
National standards shall apply!
On
DSP1300T-3500T--IO-16s.book Seite 20 Dienstag, 27. November 2018 4:39 16
/
