Philips AC1214/10R1 Používateľská príručka

Kategória
Čističe vzduchu
Typ
Používateľská príručka

Táto príručka je tiež vhodná pre

EN User manual 1
CS Příručka pro uživatele 18
HU Felhasználói kézikönyv 36
PL Instrukcja obsługi 55
RO Manual de utilizare 74
SK Príručka užívateľa 94
UK Посібник користувача 113
© 2019 Koninklijke Philips N.V.
All rights reserved.
4241 210 98194
AC1214
1 2
J K L N OM
E
F
G
H
I
A
B
D
C
3s
3s
3s
3s
Contents
1 Important 2
Safety 2
2 Your air purier 5
Product overview (Fig. a) 5
Controls overview (Fig. b) 5
3 Getting started 5
Installing the lters 5
Wi-Fi connection 6
4 Using the air purier 7
Understanding the air quality light 7
Turning on and o 7
Changing the fan speed 7
Light sensor 8
Night sensing mode 8
Setting the child lock 9
5 Cleaning 9
Cleaning the body of the air
purier 9
Cleaning the air quality sensor 9
Cleaning the pre-lter 10
6 Replacing the lters 11
Filter replacement indicator 11
Replacing the lters 11
Filter reset 12
1EN
English
7 Storage 12
8 Troubleshooting 13
9 Guarantee and service 16
Order parts or accessories 16
10 Notices 16
Electromagnetic elds (EMF) 16
Recycling 17
Notice 17
Simplied EU declaration of
conformity 17
2 EN
If the power cord is
damaged, you must have
it replaced by Philips, a
service center authorized
by Philips, or similarly
qualied persons in order
to avoid a hazard.
Do not use the appliance
if the plug, the power cord,
or the appliance itself is
damaged.
This appliance can be
used by children aged
from 8 years and above
and persons with reduced
physical, sensory or
mental capabilities or
lack of experience and
knowledge if they have
been given supervision or
instruction concerning use
of the appliance in a safe
way and understand the
hazards involved. Child
shall not play with the
appliance. Cleaning and
maintenance shall not be
made by children without
supervision.
Do not block the air inlet
and outlet, e.g. by placing
items on the air outlet or
in front of the air inlet.
1 Important
Safety
Read this user manual carefully before
you use the appliance, and save it for
future reference.
Danger
Do not let water or any
other liquid or ammable
detergent enter the
appliance to avoid electric
shock and/or a re hazard.
Do not clean the
appliance with water,
any other liquid, or a
(ammable) detergent to
avoid electric shock and/
or a re hazard.
Do not spray any
ammable materials
such as insecticides or
fragrance around the
appliance.
Warning
Check if the voltage
indicated on the
appliance corresponds to
the local power voltage
before you connect the
appliance.
Do not place anything on
top of the appliance.
Do not sit or stand on
the appliance. Sitting or
standing on the appliance
may lead to potential
injury.
Do not place the
appliance directly below
an air conditioner to
prevent condensation
from dripping onto the
appliance.
Make sure all lters
are properly installed
before you switch on the
appliance.
Only use the original
Philips lters specially
intended for this
appliance. Do not use any
other lters.
Combustion of the lter
may cause inreversible
human hazard and/or
jeopardize other lives. Do
not use the lter as fuel or
for similar purpose.
Avoid knocking against
the appliance (the air inlet
and outlet in particular)
with hard objects.
Make sure that foreign
objects do not fall into
the appliance through the
air outlet.
Standard WiFi interface
based on 802.11b/g/n at
2.4 GHz with a maximum
output power of 31.62 mW
EIRP.
Caution
This appliance is not
a substitute for proper
ventilation, regular
vacuum cleaning, or use
of an extractor hood or
fan while cooking.
If the power socket used
to power the appliance
has poor connections,
the plug of the appliance
becomes hot. Make
sure that you plug the
appliance into a properly
connected power socket.
Always place and use the
appliance on a dry, stable,
level, and horizontal
surface.
Leave at least 20cm
free space behind and
on both sides of the
appliance and leave at
least 30cm free space
above the appliance.
3EN
English
To prevent interference,
place the appliance at
least 2 meters away from
electrical appliances that
use airborne radio waves
such as TVs, radios, and
radio-controlled clocks.
The appliance is only
intended for household
use under normal
operating conditions.
Do not use the appliance
in wet surroundings or in
surroundings with high
ambient temperatures,
such as the bathroom,
toilet, or kitchen.
The appliance does
not remove carbon
monoxide (CO) or radon
(Rn). It cannot be used
as a safety device in
case of accidents with
combustion processes
and hazardous chemicals.
If you need to move the
appliance, disconnect the
appliance from the power
supply rst.
Do not move the
appliance by pulling its
power cord.
Always lift or move the
appliance by the handle
on top of the appliance.
Do not insert your ngers
or objects into the air
outlet or the air inlet to
prevent physical injury
or malfunctioning of the
appliance.
Do not use this appliance
when you have used
indoor smoke-type insect
repellents or in places
with oily residues, burning
incense, or chemical
fumes.
Do not use the appliance
near gas appliances,
heating devices or
replaces.
Always unplug the
appliance after use and
before cleaning or carrying
out other maintenance.
Do not use the appliance
in a room with major
temperature changes,
as this may cause
condensation inside the
appliance.
4 EN
3 Getting started
Installing the lters
Note
Make sure the air purier is
unplugged from the electrical outlet
before installing the lters.
Make sure the side of the lter with
the tag is pointing towards you.
1 Pull the bottom part of the front
panel and gently lift to remove it
from the air purier (Fig. c).
2 Press the clip down (1) and pull the
pre-lter towards you (2) (Fig. d).
3 Remove all lters (Fig. e).
4 Remove all packaging materials
from the lters (Fig. f).
5 Place the thick lter (FY1410) into
the air purier and then the thin
active carbon lter (FY1413) (Fig. g).
The model numbers are shown on
each lter.
6 Attach the pre-lter back into the
air purier (Fig. h).
Note
Make sure the side with the clip is
pointing towards you, and that all
hooks of the pre-lter are properly
attached to the purier.
7 Reattach the front panel by pressing
the top part of the panel onto the
top of the air purier (1). Then, gently
push the panel against the body of
the air purier (2) (Fig. i).
8 Wash your hands thoroughly after
installing lters.
2 Your air purifier
Congratulations on your purchase, and
welcome to Philips!
To fully benet from the support that
Philips oers, register your product at
www.philips.com/welcome.
Product overview
(Fig. a)
A Control panel
B Air quality light
C Air outlet
D Air quality sensor
E
NanoProtect lter Series 3
(FY1410)
F
NanoProtect lter Active Carbon
(FY1413)
G Pre-lter
H Air inlet
I Front panel
Controls overview
(Fig. b)
J On/O button
K Night sensing mode button
L Display screen
M Wi-Fi indicator
N Fan speed button
O Child lock button
5EN
English
Note
This instruction is only valid when
the air purier is being set up for the
rst time. If the network has changed
or the setup needs to be performed
again, consult section "Reset the Wi-
Fi connection" on page 6.
If you want to connect more than
one air purier to your smartphone
or tablet, you have to do this one by
one. Complete the set up of one air
purier before you turn on the other
air purier.
Make sure that the distance
between your smartphone or tablet
and the air purier is less than 10 m
without any obstructions.
This app supports the latest
versions of Android and iOS. Please
check www.philips.com/cleanhome
for the latest update of supported
operating systems and devices.
Reset the Wi-Fi connection
Note
This applies when the default
network to which your purier is
connected has changed.
Reset the Wi-Fi connection when
your default network has changed.
1 Put the plug of the air purier in the
power socket and touch
to turn
on the air purier.
2 Touch and simultaneously for
3 seconds until you hear a beep.
» The air purier goes to pairing
mode.
» The Wi-Fi indicator
blinks
orange.
3 Follow the steps 4-5 in "Setting up
the Wi-Fi connection for the rst
time" section.
Wi-Fi connection
Setting up the Wi-Fi connection
for the rst time
1 Download and install the Philips
"Clean Home+" app from the App
Store or Google Play.
2 Put the plug of the air purier in the
power socket and touch
to turn
on the air purier.
» The Wi-Fi indicator
blinks
orange for the rst time.
3 Make sure that your smartphone or
tablet is successfully connected to
your Wi-Fi network.
4 Launch the "Clean Home+" app and
click on "Connect a New Device"
or press the "+" button on the top
of the screen. Follow the onscreen
instructions to connect the air
purier to your network.
5 After the successful pairing and
connection, the Wi-Fi indicator
will light up white. If pairing
is not successful, consult the
troubleshooting section, or the
help section in the "Clean Home+"
app for extensive and up-to-date
troubleshooting tips.
6 EN
» The air purier operates under
the auto-purication mode by
default.
» When the air purier is warming
up, "
" displays on the screen.
» After measuring the air
quality for approximately
30 seconds, the air quality
sensor automatically selects
the appropriate air quality light
color.
3 Touch and hold for 3 seconds to
switch o the air purier.
Note
If the air purier stays connected
to the electrical outlet after turning
OFF, the air purier will operate
under the previous settings when
turned ON again.
If the air purier accidentally
shuts o during running, it restarts
automatically and operates under
previous settings when the power
supply is resumed.
Changing the fan speed
There are several fan speeds available.
You can choose the auto-purication
mode, speed 1, 2, 3 or turbo mode (t).
Auto-purication mode
Touch the fan speed button
repeatedly to select the auto-
purication mode (Fig. k).
4 Using the air
purifier
Understanding the air
quality light
Air quality light color Air quality level
Blue Good
Blue-Purple Fair
Purple-Red Poor
Red Very poor
The air quality light automatically goes
on when the air purier is switched on,
and lights up all colors in sequence.
After approximately 30 seconds, the
air quality sensors select the color that
corresponds to the surrounding air
quality of airborne particles.
Turning on and o
Note
Always place the air purier on a
stable, horizontal, and level surface
with the front of the unit facing
away from walls or furniture.
For optimum purication
performance, close doors and
windows.
Keep curtains away from the air inlet
or air outlet.
1 Put the plug of the air purier in the
power socket.
2 Touch to switch on the air purier
(Fig. j).
» The air purier beeps.
7EN
English
Night sensing mode
You can activate the night sensing
mode in two ways.
Activating the night sensing
mode manually
Before you go to sleep, touch
manually to activate the night
sensing mode (Fig. o).
» If the air quality light is blue,
the air purier directly goes to
the night sensing mode. The air
purier operates quietly and the
air quality light will be dimmed.
» If the air quality light is not blue,
the air purier operates under
turbo mode for a maximum of
10 minutes, the air quality light
blinks slow during this time, and
then goes to the night sensing
mode.
Auto activating the night
sensing mode
When the air purier operates in auto
mode or allergen mode, if the light
sensor detects the lights in your room
are turned o, the air purier goes to
the night sensing mode automatically.
The air purier will adjust the fan speed
in real-time to make sure the air in your
room is good. The air quality light will be
dimmed.
Allergen mode
The specially designed allergen
mode can eectively reduce common
allergens such as pollen and pet
dander.
Touch the fan speed button
to
select the Allergen mode (Fig. l).
» Auto (A) and
display on the
screen.
Manual
Touch the fan speed button
repeatedly to select the fan speed
you need (Fig. m).
Turbo (t)
In turbo mode, the air purier operates
on the highest speed.
Touch the fan speed button
to
select the turbo mode (t) (Fig. n).
Light sensor
With the light sensor, the air purier can
work according to the ambient light.
When the ambient light dims for
10 seconds, all the lights on the control
panel will turn o slowly. During this
period, you can touch any of the
buttons, all lights will turn on again. If
you don't perform other operations
within 10 seconds, all lights will turn o.
After the ambient light becomes bright
and lasts at least for 10 seconds, all
lights will turn on again.
8 EN
5 Cleaning
Note
Always turn the air purier o and
unplug the air purier from the
electrical outlet before cleaning.
Never immerse the air purier in
water or any other liquid.
Never use abrasive, aggressive, or
ammable cleaning agents such as
bleach or alcohol to clean any part
of the air purier.
Only the pre-lter is washable. The
air lter is not washable.
Do not attempt to clean the lters
or air quality sensor with a vacuum.
Cleaning the body of the
air purier
Regularly clean the inside and outside
of the air purier to prevent dust from
collecting.
1 Use a soft, dry cloth to clean both
the interior and exterior of the air
purier.
2 The air outlet can also be cleaned
with a dry, soft cloth.
3 Detach the front cover from the air
purier and wash it under running
tap water.
Cleaning the air quality
sensor
Clean the air quality sensor every
2 months for optimal functioning of the
purier.
Note
The light sensor detects the lights in
your room after 11 hours in the night
sensing mode.
If the lights in your room are turned
on, the air purier will quit the night
sensing mode and operate under
the previous mode. The air quality
light and the display will be on
again.
To exit the night sensing mode
manually, touch or button.
Setting the child lock
1
Touch and hold the child lock
button
for 3 seconds to activate
child lock (Fig. p).
» The child lock icon
displays
on the screen.
» When the child lock is on,
all the other buttons are not
responsive, only the child lock
icon
blinks.
2 Touch and hold the child lock
button
for 3 seconds again to
deactivate child lock (Fig. q).
» The child lock icon
disappears.
Note
The child lock function is
automatically unlocked when the
pre-lter cleaning code or the lter
replacement code displays on the
screen.
9EN
English
3 Press the clip down (1) and pull the
pre-lter towards you (2) (Fig. d).
4 If the pre-lter is very dirty, use a soft
brush to brush away the dust. Then
wash the pre-lter under running
tap water (Fig. w).
5 Allow the pre-lter to air dry
thoroughly before placing back in
the air purier.
Note
To optimize the lifetime of the pre-
lter, make sure it dries completely
after cleaning.
Wash your hands after handling the
lter.
6 Put the pre-lter back into the air
purier (Fig. h).
Note
Make sure the side with the clip is
pointing towards you, and that all
hooks of the pre-lter are properly
attached to the air purier.
7 To reattach the front panel, press
the top part of the panel onto the
top of the air purier (1). Then, gently
push the panel against the body of
the air purier (2) (Fig. i).
8 Put the plug of the air purier in the
power socket.
9 Touch and hold the for
3 seconds to reset the pre-lter
cleaning time (Fig. x).
10 Wash your hands thoroughly after
installing lters.
Note
If the air purier is used in a dusty
environment, it may need to be
cleaned more often.
If the humidity level in the room
is very high, condensation may
develop on the air quality sensor
and the air quality light may indicate
a more poor air quality even though
the air quality is actually good. If this
occurs, clean the air quality sensor
or use the air purier on a manual
speed setting.
1 Switch o the air purier and
unplug from the power socket.
2 Clean the air quality sensor inlet
and outlet with a soft brush
(Fig. r).
3 Open the air quality sensor cover
(Fig. s).
4 Clean the air quality sensor, the
dust inlet and the dust outlet with a
damp cotton swab (Fig. t).
5 Dry all parts thoroughly with a dry
cotton swab.
6 Reattach the air quality sensor
cover (Fig. u).
Note
Always keep air quality cover closed
while the air purier is working.
Cleaning the pre-lter
Clean the pre-lter when F0 is displayed
on the screen (Fig. v).
1 Switch o the air purier and
unplug from the power socket.
2 Pull the bottom part of the front
panel and then gently lift to remove
it from the air purier (Fig. c).
10 EN
Filter alert light
status
Action
A3 displays on
the screen
Replace
NanoProtect lter
Series 3 (FY1410)
C7 displays on
the screen
Replace
NanoProtect lter
Active Carbon
(FY1413)
A3 and C7
display on
the screen
alternately
Replace both lters
1 Turn o the air purier and unplug
from the power socket.
2 Take out the used air lter according
to the lter alert light status
displayed on the screen (Fig. y).
Discard used lters.
Note
Do not touch the pleated lter
surface, or smell the lter as it has
collected pollutants from the air.
3 Remove all packaging material from
the new lter (Fig. f).
4 Place the new lters into the air
purier (Fig. g).
5 Put the plug of the air purier in the
power socket.
6 Touch and hold the for 3 seconds
to reset the lter lifetime counter
(Fig. z).
7 Wash your hands after changing a
lter.
6 Replacing the
filters
Filter replacement
indicator
This air purier is equipped with a
lter replacement indicator to make
sure that the air purication lter is in
optimal condition when the air purier
is operating. When the lters need to be
replaced, the lter code displays on the
screen.
If the lters are not replaced in time,
the air purier will stop operating and
automatically lock.
Replacing the lters
Note
The air purication lters are not
washable nor vacuum cleanable.
Always turn o the air purier and
unplug from the electrical outlet
before replacing the lters.
Do not clean the lters with a
vacuum cleaner.
If the pre-lter is damaged, worn or
broken, do not use. Visit
www.philips.com/support or contact
the Consumer Care Center in your
country.
11EN
English
7 Storage
1 Turn o the air purier and unplug
from the power socket.
2 Clean the air purier, air quality
sensor and pre-lter (see chapter
‘Cleaning’).
3 Let all parts dry thoroughly before
storing.
4 Wrap the lter and pre-lter
separately in air tight plastic bags.
5 Store the air purier, the lter and
pre-lter in a cool, dry location.
6 Always thoroughly wash hands after
handling lters.
Filter reset
You can replace lters even if there is
no lter replacement code displayed on
the screen. After replacing a lter, you
need to reset the lter lifetime counter
manually.
1 Touch and simultaneously for
3 seconds to enter the lter reset
mode (Fig. {).
» Code (A3) of the NanoProtect
lter Series 3 displays on the
screen.
2 Touch and hold for 3 seconds to
force reset the lter lifetime counter
of the NanoProtect lter Series 3
(Fig. z).
3 Code (C7) of the Nanoprotect lter
Active Carbon displays on the
screen after the lifetime counter of
the NanoProtect lter Series 3 has
been reset (Fig. |).
4 Touch and hold for 3 seconds to
force reset the lter lifetime counter
of the NanoProtect lter Active
Carbon and exit the lter reset
mode (Fig. }).
12 EN
8 Troubleshooting
This chapter summarizes the most common problems you could encounter with the
appliance. If you are unable to solve the problem with the information below, contact
the Consumer Care Center in your country.
Problem Possible solution
The air purier
does not work
even though it is
plugged in to the
power socket and
switched on.
Check if the front cover is properly installed.
The lter replacement code has been displaying on the
screen but you have not replaced the corresponding lter
yet. The appliance will be locked if you keep using the
expired lter. In this case, replace the lter and reset the
lter lifetime counter.
The air purier
does not work
even though it is
switched on.
The lter replacement indicator has been on continuously
but you have not replaced the corresponding lter, and the
air purier is now locked. In this case, replace the lter and
reset the lter lifetime counter.
The air purier
accidentally powers
o.
The air purier restarts automatically and goes to the
previous mode when the power resumes.
The airow that
comes out of
the air outlet is
signicantly weaker
than before.
The pre-lter is dirty. Clean the pre-lter (see chapter
"Cleaning").
The air quality
does not improve,
even though the air
purier has been
operating for a long
time.
One of the lters has not been placed in the air purier or
the lter is not placed properly. Make sure that all lters are
properly installed in the following order, starting with the
innermost lter:
1) NanoProtect lter Series 3 (FY1410); 2) NanoProtect lter
Active Carbon (FY1413) 3) pre-lter.
The air quality sensor is wet. Make sure that the air quality
sensor is clean and dry (see chapter "Cleaning").
The color of the air
quality light always
stays the same.
The air quality sensor is dirty. Clean the air quality sensor
(see chapter "Cleaning").
13EN
English
Problem Possible solution
The air purier
produces a
unpleasant smell.
The lter may produce smell after being used for a while
because of the absorption of indoor air. Remove the lter
and place it where it has direct sunlight and ventilation for
several hours. Re-install and try using it again. If the odor
remains, please replace the lter.
If the air purier produces a burnt odor, switch OFF and
unplug from the electrical outlet. Contact Consumer Care
Center in your country.
The air purier is
loud.
If the air purier is too loud, change the fan speed to a
lower fan speed level. When using the air purier in a
bedroom at night, choose the night sensing mode or select
a lower fan speed level.
The air purier still
indicates that I
need to replace a
lter, but I already
did.
Perhaps you did not reset the lter lifetime counter. Plug
in the air purier, touch
to switch on the air purier, and
touch and hold the
for 3 seconds.
Error codes "E1",
"E2", "E3" or "E4"
displays on the
screen.
The appliance has malfunctions. Contact the Consumer
Care Center in your country.
Which app I should
download?
Download and install the Philips "Clean Home+" app from
the App Store or Google Play.
14 EN
Problem Possible solution
The Wi-Fi setup is
not successful.
If the router your purier is connected to is dual – band
and currently it is not connecting to a 2.4GHz network,
please switch to another band of the same router (2.4GHz)
and try to pair your purier again. 5GHz networks are not
supported.
Web authentication networks are not supported.
Check if the purier is within range of the Wi-Fi router. You
can try to locate the air purier closer to the Wi-Fi router.
Check if the network name is correct. The network name is
case-sensitive.
Check if the Wi-Fi password is correct. The password is
case-sensitive.
Retry the setup with the instructions in section ‘Set up the
Wi-Fi connection when the network has changed’.
The Wi-Fi connectivity can be interrupted by electromagnetic
or other interferences. Keep the appliance away from other
electronic devices that may cause interferences.
Check if the mobile device is in airplane mode. Make sure
to have the airplane mode deactivated when connecting
to the Wi-Fi network.
Consult the help section in the App for extensive and up-
to-date troubleshooting tips.
15EN
English
9 Guarantee and
service
If you need information or if you have a
problem, please visit the Philips website
at www.philips.com or contact the
Philips Consumer Care Center in your
country (you nd its phone number
in the worldwide guarantee leaet). If
there is no Consumer Care Centre in
your country, go to your local Philips
dealer.
Order parts or
accessories
If you have to replace a part or want to
purchase an additional part, go to your
Philips dealer or visit
www.philips.com/support.
If you have problems obtaining the
parts, please contact the Philips
Consumer Care Center in your country
(you can nd its phone number in the
worldwide guarantee leaet).
10 Notices
Electromagnetic elds
(EMF)
This Philips appliance complies with all
applicable standards and regulations
regarding exposure to electromagnetic
elds.
Compliance with EMF
Koninklijke Philips N.V. manufactures
and sells many products targeted at
consumers, which, like any electronic
apparatus, in general have the ability
to emit and receive electromagnetic
signals.
One of Philips' leading Business
Principles is to take all necessary health
and safety measures for our products,
to comply with all applicable legal
requirements and to stay well within the
EMF standards applicable at the time of
producing the products.
Philips is committed to develop,
produce and market products that
cause no adverse health eects. Philips
conrms that if its products are handled
properly for their intended use, they
are safe to use according to scientic
evidence available today.
Philips plays an active role in the
development of international EMF
and safety standards, enabling Philips
to anticipate further developments in
standardization for early integration in
its products.
16 EN
Recycling
This symbol means that this product
shall not be disposed of with normal
household waste (2012/19/EU).
Follow your country’s rules for the
separate collection of electrical and
electronic products. Correct disposal
helps prevent negative consequences
for the environment and human health.
Notice
App Store is a service mark of Apple Inc.
Google Play is a trademark of Google
Inc.
This Philips appliance and Clean
Home+ app applied multiple open
source softwares, Copies of open
source software license text used in this
product can be derived from website-
www.philips.com/cleanhome.
Simplied EU declaration
of conformity
Hereby, Philips Consumer Lifestyle B.V.
declares that the radio equipment type
AC1214 is in compliance with Directive
2014/53/EU. The full text of the EU
declaration of conformity is available at
the following internet address:
www.philips.com.
17EN
English
Obsah
1 Důležité 19
Bezpečnost 19
2 Vaše čistička vzduchu 22
ehled výrobku (obr. a) 22
ehled ovládacích prvků
(obr. b) 22
3 Začínáme 22
Instalace ltrů 22
Připojení Wi-Fi 23
4 Použití čističky vzduchu 24
Jak funguje kontrolka kvality
vzduchu 24
Vypnutí a zapnutí 24
Změna rychlosti ventilátoru 24
Světelný senzor 25
Noční režim 25
Nastavení dětské pojistky 26
5 Čištění 26
Čištění těla čističky 26
Čištění snímače kvality vzduchu 27
Čištění předltru 27
6 Výměna ltrů 28
Indikátor výměny ltru 28
Výměna ltrů 28
Resetování ltru 29
18 CS
7 Uskladnění 30
8 Odstraňování problémů 31
9 Záruka a servis 34
Objednání dílů nebo doplňků 34
10 Upozornění 34
Elektromagnetická pole (EMP) 34
Recyklace 35
Oznámení 35
Zjednodušené EU prohlášení
o shodě 35
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134

Philips AC1214/10R1 Používateľská príručka

Kategória
Čističe vzduchu
Typ
Používateľská príručka
Táto príručka je tiež vhodná pre