HOTPOINT/ARISTON RDPD 117607 JD EU Užívateľská príručka

Kategória
Práčky
Typ
Užívateľská príručka
GB
1
! This symbol reminds you to read this instruc-
tion manual.
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Care and maintenance, 4
Cutting off the water or electricity supply
Cleaning the washer-dryer
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Precautions and tips, 5
General safety
Disposal
Opening the porthole door manually
Description of the washer-dryer, 6-7
Control panel
Display
How to run a wash cycle or a drying cycle, 8
Wash cycles and functions, 9
Table of wash cycles
Wash functions
Detergents and laundry, 10
Detergent dispenser drawer
Preparing the laundry
Special wash cycles
Load balancing system
Troubleshooting, 11
Service, 12
RDPD 117607 J
Instructions for use
WASHER-DRYER
English,1
GB
HU
Magyar,37
Česky,13
CZ
Slovensky,25
SK
Hrvatski,49
HR
ΕΛΛΗΝΙΚΑ,61
GR
2
GB
Installation
! This instruction manual should be kept in a safe
place for future reference. If the washer-dryer is
sold, transferred or moved, make sure that the
instruction manual remains with the machine so
that the new owner is able to familiarise himself/
herself with its operation and features.
! Read these instructions carefully: they con-
tain vital information relating to the safe instal-
lation and operation of the appliance.
Unpacking and levelling
Unpacking
1. Remove the washer-dryer from its packa-
ging.
2. Make sure that the washer-dryer has not
been damaged during the transportation
process. If it has been damaged, contact the
retailer and do not proceed any further with
the installation process.
3. Remove the 4 pro-
tective screws (used
during transportation)
and the rubber wa-
sher with the cor-
responding spacer,
located on the rear
part of the appliance
(see figure).
4. Close off the holes using the plastic plugs
provided.
5. Keep all the parts in a safe place: you will
need them again if the washer-dryer needs to
be moved to another location.
! Packaging materials should not be used as
toys for children.
Levelling
1. Install the washer-dryer on a flat sturdy floor,
without resting it up against walls, furniture
cabinets or anything else.
2. If the floor is not
perfectly level, com-
pensate for any une-
venness by tightening
or loosening the
adjustable front feet
(see figure); the angle
of inclination, measu-
red in relation to the
worktop, must not
exceed 2°.
Levelling the machine correctly will provide
it with stability, help to avoid vibrations and
excessive noise and prevent it from shifting
while it is operating. If it is placed on carpet or
a rug, adjust the feet in such a way as to allow
a sufficient ventilation space underneath the
washer-dryer.
Connecting the electricity and
water supplies
Connecting the water inlet hose
1. Connect the A
device to a cold water
tap using a 3/4 gas
threaded attachment,
then perform the con-
nection by screwing
the supply hose to the
device.
Before performing the
connection, allow the
water to run freely until it is perfectly clear.
For a correct installation of the device, follow
the instructions given in the packaging.
! The device is already adjusted for the cor-
rect operation of the washing machine and
therefore it is recommended not to change its
settings.
2. Connect the inlet
hose to the washer-
dryer by screwing it
onto the correspon-
ding water inlet of the
appliance, which is
situated on the top
right-hand side of the
rear part of the ap-
pliance (see figure).
3. Make sure that the hose is not folded over
or bent.
! The water pressure at the tap must fall within
the range of values indicated in the Technical
data table (see next page).
! If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.
! Never use second-hand hoses.
! Use the ones supplied with the machine.
A
GB
3
Connecting the drain hose
Connect the drain
hose, without bending
it, to a drain duct or
a wall drain situated
between 65 and 100
cm from the floor;
alternatively, placed
it over the edge of a
basin, sink or tub, fa-
stening the duct sup-
plied to the tap (see
figure). The free end
of the hose should
not be underwater.
! We advise against the use of hose extensions;
if it is absolutely necessary, the extension must
have the same diameter as the original hose
and must not exceed 150 cm in length.
Electrical connections
Before plugging the appliance into the electri-
city socket, make sure that:
• thesocketisearthedandcomplieswithall
applicable laws;
• thesocketisabletowithstandthemaxi-
mum power load of the appliance as indicated
in the Technical data table (see opposite);
• thepowersupplyvoltagefallswithintheva-
lues indicated in the Technical data table (see
opposite);
• thesocketiscompatiblewiththeplugofthe
washer-dryer. If this is not the case, replace
the socket or the plug.
! The washer-dryer must not be installed ou-
tdoors, even in covered areas. It is extremely
dangerous to leave the appliance exposed to
rain, storms and other weather conditions.
! When the washer-dryer has been installed,
the electricity socket must remain within easy
reach.
! Do not use extension cords or multiple sockets.
! The cable should not be bent or compressed.
! The power supply cable must only be repla-
ced by authorised technicians.
65 - 100 cm
Warning! The company shall not be held re-
sponsible in the event that these standards are
not observed.
The first wash cycle
Once the appliance has been installed, and
before you use it for the first time, run a wash
cycle with detergent and no laundry, using
wash cycle auto clean (see “Cleaning the
washer-dryer”).
Technical data
Model
RDPD 117607 J
Dimensions
width 59.5 cm
height 85 cm
depth 60,5 cm
Capacity
from 1 to 11 kg for the wash
programme
from 1 to 7 kg for the drying
programme
Electrical
connections
please refer to the technical
data plate fixed to the machine
Water con-
nections
maximum pressure
1 MPa (10 bar)
minimum pressure
0.05 MPa (0.5 bar)
drum capacity 71 litres
Spin speed
up to 1600 rotations per
minute
Energy
rated
programmes
according to
regulation
EN 50229
Wash: programme 8; tem-
perature 60°C; using a load
of 11 kg.
Drying: the greater load
(7kg) must be dried by se-
lecting the “EXTRA” dryness
level.
The remainder of the load
must be dried by selecting
the “EXTRA” dryness level:
the load must consist of 3
sheets and 7 pillowcases.
This appliance conforms to
the following EC Directives:
- 2004/108/EC (Electroma-
gnetic Compatibility)
- 2006/95/EC (Low Voltage)
- 2012/19/EU (WEEE)
4
GB
Cleaning the pump
The washer-dryer is fitted with a self-cleaning
pump which does not require any maintenan-
ce. Sometimes, small items (such as coins or
buttons) may fall into the pre-chamber which
protects the pump, situated in its bottom part.
! Make sure the wash cycle has finished and
unplug the appliance.
To access the pre-chamber:
1. using a screwdri-
ver, remove the
cover panel on the
lower front part of the
washer-dryer (see
figure);
2. unscrew the lid
by rotating it anti-
clockwise (see figu-
re): a little water may
trickle out. This is
perfectly normal;
3. clean the inside thoroughly;
4. screw the lid back on;
5. reposition the panel, making sure the hooks
are securely in place before you push it onto
the appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If
there are any cracks, it should be replaced
immediately: during the wash cycles, water
pressure is very strong and a cracked hose
could easily split open.
! Never use second-hand hoses.
Care and maintenance
Cutting off the water and electri-
city supplies
•Turnoffthewatertapaftereverywashcycle.
This will limit wear on the hydraulic system
inside the washer-dryer and help to prevent
leaks.
•Unplugthewasher-dryerwhencleaningit
and during all maintenance work.
Cleaning the washer-dryer
•Theouterpartsandrubbercomponents
of the appliance can be cleaned using a soft
cloth soaked in lukewarm soapy water. Do not
use solvents or abrasives.
•Thewasher-dryerhasaautocleanpro-
gramme for its internal parts that must be run
with no load in the drum.
To help the wash cycle you may want to use
either the detergent (i.e. a quantity 10% the
quantity specified for lightly-soiled garments)
or special additives to clean the washer-dryer.
We recommend running a cleaning program-
me every 40 wash cycles.
To activate the programme, press the but-
ton for 5 seconds then press START/PAUSE
to start the programme, which will last roughly
70 minutes.
Cleaning the detergent dispenser
drawer
Remove the dispen-
ser by raising it and
pulling it out (see
figure).
Wash it under running
water; this operation
should be repeated
frequently.
Caring for the door and drum of
your appliance
•Alwaysleavetheportholedoorajarinorder
to prevent unpleasant odours from forming.
1
2
GB
5
Precautions and tips
! This washer-dryer was designed and constructed in
accordance with international safety regulations. The fol-
lowing information is provided for safety reasons and must
therefore be read carefully.
General safety
• This appliance was designed for domestic use only.
Thisappliancecanbeusedbychildrenaged
from 8 years and above and persons with
reduced physical, sensory or mental capabi-
lities or lack of experience and knowledge if
they have been given supervision or instruction
concerning use of the appliance in a safe way
and understand the hazards involved. Children
shall not play with the appliance. Cleaning and
user maintenance shall not be made by children
without supervision.
Do not dry unwashed items in the tumble dryer.
– Items that have been soiled with substan-
ces such as cooking oil, acetone, alcohol,
petrol, kerosene, spot removers, turpentine,
waxes and wax removers should be washed
in hot water with an extra amount of deter-
gent before being dried in the tumble dryer.
– Items such as foam rubber (latex foam),
shower caps, waterproof textiles, rubber
backed articles and clothes or pillows fitted
with foam rubber pads should not be dried in
the tumble dryer.
– Fabric softeners, or similar products,
should be used as specified by the fabric
softener instructions.
The final part of a tumble dryer cycle occurs
without heat (cool down cycle) to ensure that
the items are left at a temperature that ensures
that the items will not be damaged.
WARNING: Never stop a tumble dryer before
the end of the drying cycle unless all items
are quickly removed and spread out so that
the heat is dissipated.
•Do not touch the machine when barefoot or with wet or
damp hands or feet.
•Do not pull on the power supply cable when unplugging
the appliance from the electricity socket. Hold the plug
and pull.
•Do not open the detergent dispenser drawer while the
machine is in operation.
•Do not touch the drained water as it may reach extreme-
ly high temperatures.
•Never force the porthole door. This could damage the
safety lock mechanism designed to prevent accidental
opening.
•If the appliance breaks down, do not under any circum-
stances access the internal mechanisms in an attempt
to repair it yourself.
•Always keep children well away from the appliance while
it is operating.
•The door can become quite hot during the wash cycle.
•If the appliance has to be moved, work in a group of two
or three people and handle it with the utmost care. Never
try to do this alone, because the appliance is very heavy.
•Before loading laundry into the washer-dryer, make sure
the drum is empty.
• During the drying phase, the door tends to get quite hot.
• Donotusetheappliancetodryclothesthat
have been washed with flammable solvents
(e.g. trichlorethylene).
• Donotusetheappliancetodryfoamrubber
or similar elastomers.
• Make sure that the water tap is turned on during
the drying cycles.
• Childrenoflessthan3yearsshouldbekept
away from the appliance unless continuou-
sly supervised.
• Removeallobjectsfrompocketssuchas
lighters and matches.
Disposal
• Disposingofthepackagingmaterials:observelocal
regulations so that the packaging may be re-used.
• TheEuropeanDirective2012/19/EUonWaste
Electrical and Electronic Equipment, requires that
old household electrical appliances must not be
disposed of in the normal unsorted municipal waste
stream. Old appliances must be collected
separately in order to optimise the recovery and
recycling of the materials they contain and reduce
the impact on human health and the environment.
The crossed out “wheeled bin” symbol on the
product reminds you of your obligation, that when
you dispose of the appliance it must be separately
collected.
Consumers should contact their local authority or
retailer for information concerning the correct
disposal of their old appliance.
Opening the porthole door manually
In the event that it is not possible to open the porthole
door due to a powercut, and if you wish to remove the
laundry, proceed as follows:
1. remove the plug from the electrical socket.
2. make sure the water level inside the machine is lower
than the door opening; if it is not, remove excess water
using the drain hose, collecting it in a bucket as indicated
in the figure.
3. using a screwdriver, remove the cover panel on the
lower front part of the washer-dryer (see figure).
4. pull outwards using the tab as indicated in the figure,
until the plastic tie-rod is freed from its stop position; pull
downwards and open the door at the same time.
5. reposition the panel, making sure the hooks are securely
in place before you push it onto the appliance.
20
6
GB
Detergent dispenser drawer: used to dispense
detergents and washing additives (see “Detergents and
laundry”).
Programme Key: the Programme Key inside the deter-
gent dispenser shows all the available programmes toge-
ther with a graphical guide on how to use the individual
dispenser compartments.
ON/OFF button : press this briefly to switch the ma-
chine on or off. The START/PAUSE indicator light, which
flashes slowly in a green colour shows that the machine
is switched on. To switch off the washer-dryer during the
wash cycle, press and hold the button for approximately 3
seconds; if the button is pressed briefly or accidentally the
machine will not switch off. If the machine is switched off
during a wash cycle, this wash cycle will be cancelled.
WASH CYCLE SELECTOR KNOB: used to set the desired
wash cycle (see Table of programmes and wash cycles”).
FUNCTION button: press the button to select the desired
function. The corresponding indicator light on the display
will switch on.
AUTO CLEAN button: press to clean the machine’s inter-
nal parts (see “Cleaning the washer-dryer”).
DIRECT INJECTION button: press to select the DIRECT
INJECTION option.
MULTI RINSE button : press to select the desired
rinse type.
SPIN button : press to reduce or completely exclude
the spin cycle - the value is indicated on the display.
TEMPERATURE button : press to decrease the tempe-
rature: the value will be shown on the display.
DRYING button : press to decrease or exclude drying;
the selected drying level or time will appear on the display.
DRYING ONLY button : press to run the drying cycle
only.
KEY LOCK button : to activate the control panel
lock, press and hold the button for approximately 2
seconds. When the display visualises “KEY LOCK ON” the
control panel is locked (apart from the ON/OFF button).
This means it is possible to prevent wash cycles from
being modified accidentally, especially where there are
children in the home. To deactivate the control panel lock,
press and hold the button for approximately 2 seconds.
DELAY TIMER button : press to set a delayed start
time for the selected wash cycle. The delay time will be
shown on the display.
START/PAUSE button with indicator light: when the gre-
en indicator light flashes slowly, press the button to start a
wash cycle. Once the cycle has started the indicator light
will remain lit in a fixed manner. To pause the wash cycle,
press the button again; the indicator light will flash in an
orange colour. If the symbol is not illuminated, the door
may be opened. To start the wash cycle from the point at
which it was interrupted, press the button again.
Standby mode
This washer-dryer, in compliance with new energy saving
regulations, is fitted with an automatic standby system
which is enabled after about 30 minutes if no activity is
detected. Press the ON-OFF button briefly and wait for the
machine to start up again.
Consumption in off-mode: 0,5 W
Consumption in Left-on: 8 W
Description of the washer-dryer
Control panel
TEMPERATURE
button
Detergent dispenser drawer
FUNCTION
button
ON/OFF
button
SPIN
button
START/PAUSE
button with indicator light
KEY LOCK
button
DELAY
TIMER
button
MULTI
RINSE
button
DISPLAY
AUTO
CLEAN
button
DIRECT
INJECTION
button
Programme
Key
WASH
CYCLE
SELECTOR
KNOB
DRYING ONLY
button
DRYING
button
GB
7
The display is useful when programming the machine and provides a great deal of information.
The following will appear in area A: the icon and programme selected, the washing and drying phases and time remaining to
the end of the cycle.
Area B will include the two intensity levels relative to the DIRECT INJECTION option.
The indicator lights relative to the available functions appear in area C.
Area D will have the time remaining to the start of the selected programme if the DELAY TIMER function was set.
String E shows the maximum spin speed value (this depends on the selected wash cycle); if the programme does not inclu-
de the spin cycle, the dimly lit “--” symbol will appear in the area.
Area F will visualise the temperature value selectable on the basis of the set programme; if the temperature of the program-
me cannot be set, the area will show the symbol “--” dimly lit.
Door locked symbol
If the symbol is lit, this indicates that the washer-dryer door is blocked to prevent it from being opened accidentally. To pre-
vent any damage from occurring, wait for the symbol to switch itself off before opening the appliance door.
N.B.: if the DELAY TIMER function has been activated, the door cannot be opened; pauses the machine by pressing the
START/PAUSE button if you wish to open it.
! The first time the machine is switched on, you will be asked to select the language and the display will automatically show
the language selection menu.
To select the desired language press the X and Y buttons; to confirm the selection press the Z button.
To change the language switch off the machine and press buttons G, H, I simultaneously until an alarm is heard: the
language-selection menu will be displayed again.
! To change the display luminosity, which by default is set to the highest value, switch the machine off then simultaneously
press buttons G, L and M until the buzzer sounds. Press buttons X and Y to choose the desired level of luminosity then
confirm by pressing button Z.
! During the wash cycle or when the DELAY TIMER function has been enabled, if the user does not interact with the display
for 1 minute the “SCREEN SAVER” activates. To return to the previous window, simply press any button.
Display
2:55
90°
1200
-- h
--
COTONE
H
G
Y
X Z
I
L M
A
B
C
C
D
E
C
F
8
GB
How to run a wash cycle or a
drying cycle
1. SWITCH THE MACHINE ON. Press the On/Off button ;
the text HOTPOINT will appear on the display and the START/
PAUSE indicator light will flash slowly in a green colour.
2. LOAD THE LAUNDRY. Open the porthole door. Load
the laundry, making sure you do not exceed the maximum
load value indicated in the table of programmes on the
following page.
3. MEASURE OUT THE DETERGENT. Open the
detergent dispenser drawer and pour the detergent into
the relevant compartments as described in “Detergents
and laundry”.
4. CLOSE THE DOOR.
5. SELECT THE WASH CYCLE. Use the WASH CYCLE
SELECTOR knob to select the desired wash cycle; the
name of the wash cycle will appear on the display. A
temperature and spin speed is set for each wash cycle;
these may be adjusted. The duration of the cycle will
appear on the display.
6. CUSTOMISE THE WASH CYCLE. Use the relevant
buttons:
Modifying the temperature and/or spin speed. The
machine automatically selects the maximum temperature
and spin speed set for the selected wash cycle; these
values cannot therefore be increased. The temperature
can be decreased by pressing the button, until the cold
wash (the display will visualise the “--” symbol) setting is
reached. The spin speed may be progressively reduced by
pressing the button, until it is completely excluded (the
display will visualise the “--” symbol). If these buttons are
pressed again, the maximum values are restored.
! Exception: if the 5 programme is selected, the
temperature can be increased up to a value of 40°C.
! Exception: if the 7 programme is selected, the
temperature can be increased up to a value of 90°C.
! Exception: if the 9 programme is selected, the
temperature can be increased up to a value of 60°C.
Setting a delayed start.
To set a delayed start for the selected programme, press
the corresponding button repeatedly until the required
delay period has been reached. To remove the delayed
start function press the button until the text
-- h” appears on the display.
Setting the drying cycle.
The desired drying cycle type may be set by pressing the
DRYING button once or several times. Two options are
available:
A - Based on the how damp the clothes are once they
have been dried:
Iron: suitable for clothes which will need ironing afterwards.
the remaining dampness softens creases, making them
easier to remove.
Hanger: ideal for clothes which do not need to be dried fully.
Cupboard: suitable for laundry which can be put back in a
cupboard without being ironed.
Extra: suitable for garments which need to be dried
completely, such as sponges and bathrobes.
B - Based on a set time period: between 30 and 180 minutes.
To exclude the drying phase press the relevant button until
the text OFF appears on the display.
If your laundry load to be washed and dried is much greater
than the maximum stated load, perform the wash cycle, and
when the cycle is complete, divide the garments into groups
and put some of them back in the drum. At this point, follow
the instructions provided for a Drying only” cycle. Repeat
this procedure for the remainder of the load. A cooling-down
period is always added to the end of each drying cycle.
Drying only
Press button to perform the drying-only cycle.
After selecting the desired cycle (compatible with the type
of garments), press button to exclude the washing
phase and start the drying phase at the maximum level for
the selected cycle. The drying level or time may be set and
changed by pressing the drying button . (Not compati-
ble with cycles 1-2-3-4 and 14).
Set the rinse type.
Option makes it possible to select the desired rinse
type for sensitive skin. Press the button once for the “Extra
+1” level, which makes it possible to select an additional
rinse after the standard cycle rinse and remove all traces
of detergent. Press the button again for the “Extra +2
level, which makes it possible to select two additional
rinses to the standard cycle rinses; it is recommended
for very sensitive skin. When the button is pressed for the
third time, the “Extra +3” level is set, thus allowing the
selection of 3 rinses in addition to the standard cycle’s
rinses. The option - started with cycles at a temperature of
40°C - makes it possible to remove major allergens such
as pollen, cat and dog hair. With cycles at a temperature
higher than 40° a very good level of antiallergic protection
is achieved. Press the button again to go back to the
Normal rinse” rinse type. If the current adjustment can
be neither set nor changed, the display will show “No
Selection” or “No Change”.
Modifying the cycle settings.
• Pressthebuttontoenablethefunction;therelevant
indicator light on the display will light up.
• Pressthebuttonagaintodisablethefunction;the
relevant indicator light on the display will switch off.
! If the selected function is incompatible with the set
programme, the relevant indicator light will appear dimly lit;
in addition, the incompatibility will be signalled by a buzzer
(3 beeps) and the wording “No Selection will appear on
the display.
! If the selected function is incompatible with another
previously set function, the wording “No Selection will
appear on the display and the function will not be enabled.
! The functions may affect the recommended load value
and/or the duration of the cycle.
7. START THE PROGRAMME. Press the START/PAUSE
button. The corresponding indicator light will become
green, remaining lit in a fixed manner, and the door will be
locked (the DOOR LOCKED symbol will be on). During
the wash cycle, the name of the phase in progress will
appear on the display. To change a wash cycle while it is in
progress, pause the washer-dryer using the START/PAUSE
button (the START/PAUSE indicator light will flash slowly in
an orange colour); then select the desired cycle and press
the START/PAUSE button again. To open the door while
a cycle is in progress, press the START/PAUSE button; if
the DOOR LOCKED symbol is switched off the door
may be opened. Press the START/PAUSE button again
to restart the wash cycle from the point at which it was
interrupted.
8. THE END OF THE WASH CYCLE. This will be indicated
by the textCYCLE END” on the display; when the DOOR
LOCKED symbol switches off the door may be opened.
Open the door, unload the laundry and switch off the machine.
! If you wish to cancel a cycle which has already begun, press
and hold the button. The cycle will be stopped and the
machine will switch off.
Direct Injection
The washer-dryer is equipped with the innovative technology
«Direct Injection» which pre-mixes water and detergent, thus
immediately activating the detergent’s cleaning principles.
This active emulsion is directly introduced into the drum of the
washer-dryer and penetrates the fibres with more efficacy in
cleaning even heavily soiled garments at low temperatures,
fully preserving colours and fabrics.
The mode «Power» ensures the best cleaning performance
and the mode «EcoEnergy» allows more energy saving.
GB
9
Wash cycles and functions
Table of wash cycles
Wash functions
! If the selected function is incompatible with the set pro-
gramme, the relevant indicator light will appear dimly lit; in
addition, the incompatibility will be signalled by a buzzer
(3 beeps) and the wording “No Selection” will appear on
the display.
! If the selected function is incompatible with another pre-
viously set function, the wording No Selectionwill appear
on the display and the function will not be enabled.
Steam Hygiene
This option enhances washing performance by generating
steam during the wash cycle to remove any bacteria from
the fibres, which are treated at the same time. Place the
laundry in the drum, choose a compatible programme and
select option .
! The steam generated during the operation of the washing
machine may cause the porthole door to become hazy.
1) Test wash cycle in compliance with regulation EN 50229: set wash cycle 8 with a temperature of 60°C.
2) Long wash cycle for cottons: set programme 8 at temperature 40°C and press the DIRECT INJECTION button under “Power” mode.
3) Long wash cycle for synthetics: set wash cycle 9 with a temperature of 40°C.
* If you select programme and exclude the spin cycle, the machine will drain only.
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary accor-
ding to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.
Wash cycles
Description of the wash cycle
Max.
temp.
(°C)
Max.
speed
(rpm)
Drying
Detergents
Max. load
(kg)
Cycle dura-
tion
Wash
Fabric
softener
ANTI CREASE
The duration of the wash cycle can be checked on the display.
1
Daily Mix Wash & Dry
40°
800
3
2
Shirts Wash & Dry
40°
1000
2
3
Pre Iron
- - - - - 1,5
4
Steam Refresh
- - - - - 2
DAILY CLEAN
5 Anti-Stain Turbo 45’
20°
(Max. 40°C)
1200
5,5
6 Anti-Stain Power 20°C
20°
1600
11
7
Cotton: lightly soiled resistant and delicate colours.
40°
(Max. 90°C)
1600
11
8
Eco Cotton
60°/4
(1-2): heavily soiled whites and resistant colours.
60° 1600
11
9
Synthetics (3): lightly soiled resistant colours.
40°
(Max. 60°C)
1000
5
SPECIALS
10 Multi Colour
40° 1600
11
11
Ultra Delicates
30°
--
1
12
Wool: for wool, cashmere, etc.
40° 800
2,5
13
Sport
40° 600
4,5
14
Fast 30’ (**): to refresh lightly soiled garments quickly (not suitable for wool, silk and
clothes which require washing by hand).
30° 800
4
Partial Programmes
Rinse
- 1600
-
11
Spin + Pump out
- 1600
- - 11
Pump out only *
-
--
- - - 11
** If a drying cycle is also programmed, the machine will run a “wash+dry” programme lasting 45’ with maximum spin speed and a 1kg laundry load.
10
GB
Detergent dispenser drawer
Good washing results also depend on the correct dose of
detergent: adding too much detergent will not necessarily
result in a more efficient wash, and may in fact cause a
build up on the inside of your appliance and contribute to
environmental pollution.
! Use powder detergent for white cotton garments, for pre-
washing, and for washing at temperatures over 60°C.
! Follow the instructions given on the detergent packaging.
! Do not use hand washing detergents because these
create too much foam.
Open the detergent di-
spenser drawer and pour
in the detergent or washing
additive, as follows.
! Do not pour detergent into
the middle compartment (*).
compartment 1: Deter-
gent for the wash cycle
(powder or liquid)
If liquid detergent is used, it is recommended that the
removable plastic partition A (supplied) be used for proper
dosage. If powder detergent is used, place the partition
into slot B.
compartment 2: Additives (fabric softeners, etc.)
The fabric softener should not overflow the grid.
Preparing the laundry
•Dividethelaundryaccordingto:
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from whites.
•Emptyallgarmentpocketsandcheckthebuttons.
• Donotexceedthelistedvalues,whichrefertotheweight
of the laundry when dry: see “Table of wash cycles”.
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1200 g
1 towel 150-250 g
Special wash cycles
Daily Mix Wash & Dry use programme 1 to wash and
dry mixed garments (cotton and synthetics). This cycle
may be used to wash and dry loads of up to 3 kg; we
recommend the use of liquid detergent.
The use of the steam in this programme is optimised to re-
duce the formation of creases on garments, making them
easier to iron.
Shirts Wash & Dry: use programme 2 to wash and dry
shirts and T-shirts in different fabrics and colours to ensure
maximum care. This cycle may be used to wash and dry
loads of up to 2 kg. To achieve optimum results, use liquid
detergent and pre-treat cuffs, collars and stains. The use of
the steam in this programme is optimised to reduce the for-
mation of creases on garments, making them easier to iron.
Pre Iron: use this programme immediately before ironing;
max. 1.5 kg load. The use of the steam in this programme
is optimised to reduce the formation of creases on gar-
ments, making them easier to iron.
Steam Refresh: for refreshing garments, neutralised unple-
asant odours and relaxing the fibres by delivering steam into
the drum. The garments will be damp at the end of the cycle.
Anti-Stain Turbo 45’: this cycle ensures excellent stain
removal capacity even at 20°C in just 45 minutes. The tem-
perature of this cycle can be increased up to 40°C.
Anti-Stain Power 20°C: this programme ensures ma-
ximum stain removal capacity with no need for pre-treat-
ment at low temperatures, preserving fabrics and colours.
Multi Colour: for washing coloured cotton garments.
This programme is optimised to keep colours bright even
after repeated washing.
Ultra Delicates: use programme 11 to wash very delica-
te garments having strasses or sequins.
We recommend turning the garments inside out before washing
and placing small items into the special bag for washing delica-
tes. Use liquid detergent on delicate garments for best results.
When selecting an exclusively time-based drying function,
a drying cycle is performed at the end of the wash cycle
that is particularly delicate, thanks to light handling and
appropriate temperature control of the water jet.
The recommended durations are:
1 kg of synthetic garments --> 165 min
1 kg of synthetic and cotton garments --> 180 min
1 kg of cotton garments --> 180 min
The degree of dryness depends on the load and fabric
composition.
Wool - Woolmark Apparel Care - Green:
the wool wash cycle of this machine has been approved
by The Woolmark Company for the washing of wool gar-
ments labelled as “hand wash” provided that the products
are washed according to the instructions on the garment
label and those issued by the manufacturer of this washer-
dryer. (M1135)
Sport: for washing lightly soiled sports clothing (tracksuits,
shorts, towels, etc.); for best results, we recommend not
exceeding the maximum load indicated in the “Table of
wash cycles”. We recommend using liquid detergent, and
adding the amount suitable for a half-load.
Load balancing system
Before every spin cycle, to avoid excessive vibrations and
to distribute the load in a uniform manner, the drum rotates
continuously at a speed which is slightly greater than the
washing rotation speed. If, after several attempts, the load is
not balanced correctly, the machine spins at a reduced spin
speed. If the load is excessively unbalanced, the washer-
dryer performs the distribution process instead of spinning.
To encourage improved load distribution and balance, we
recommend small and large garments are mixed in the load.
Detergents and laundry
1
2
A
B
*
GB
11
Troubleshooting
Your washer-dryer could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure that
the problem cannot be solved easily using the following list.
Problem:
The washer-dryer does not switch on.
The wash cycle does not start.
The washer-dryer does not take in
water (the text “NO WATER, Turn
tap on” appears on the display).
The washer-dryer continuously
takes in and
drains water.
The washer-dryer does not drain or
spin.
The washer-dryer vibrates a lot
during the spin cycle.
The washer-dryer leaks.
The machine is locked and the display
flashes, indicating an error code (e.g.
F-01, F-..).
There is too much foam.
The washer-dryer does not dry.
Possible causes / Solutions:
• Theapplianceisnotpluggedintothesocketfully,orisnotmakingcontact.
• Thereisnopowerinthehouse.
• Thewasher-dryerdoorisnotclosedproperly.
• TheON/OFFbuttonhasnotbeenpressed.
• TheSTART/PAUSEbuttonhasnotbeenpressed.
• Thewatertaphasnotbeenopened.
• Adelayedstarthasbeenset.
• Thewaterinlethoseisnotconnectedtothetap.
• Thehoseisbent.
• Thewatertaphasnotbeenopened.
• Thereisnowatersupplyinthehouse.
• Thepressureistoolow.
• TheSTART/PAUSEbuttonhasnotbeenpressed.
• Thedrainhoseisnotfittedataheightbetween65and100cmfromthefloor
(see “Installation”).
• Thefreeendofthehoseisunderwater(see “Installation”).
• Thewalldrainagesystemisnotfittedwithabreatherpipe.
If the problem persists even after these checks, turn off the water tap, switch
the appliance off and contact the Assistance Service. If the dwelling is on one of
the upper floors of a building, there may be problems relating to water drainage,
causing the washer-dryer to fill with water and drain continuously. Special anti-
draining valves are available in shops and help to avoid this inconvenience.
• Thewashcycledoesnotincludedraining:somewashcyclesrequirethedrain
phase to be started manually (see “Wash cycles and functions”).
• Thedrainhoseisbent(see “Installation”).
• Thedrainageductisclogged.
• Thedrumwasnotunlockedcorrectlyduringinstallation(see “Installation”).
• Thewasher-dryerisnotlevel(see “Installation”).
• Thewasher-dryeristrappedbetweencabinetsandwalls(see “Installation”).
• Thewaterinlethoseisnotscrewedonproperly(see “Installation”).
• Thedetergentdispenserdrawerisblocked(forcleaninginstructions,see “Care
and maintenance”).
• Thedrainhoseisnotfixedproperly(see “Installation”).
• Switchoffthemachineandunplugit,waitforapproximately1minuteandthen
switch it back on again.
If the problem persists, contact the Technical Assistance Service.
• Thedetergentisnotsuitableformachinewashing(itshoulddisplaythetext
“for washer-dryers” or “hand and machine wash”, or the like).
• Toomuchdetergentwasused.
• Theapplianceisnotpluggedintothesocket,ornotenoughtomakecontact.
• Therehasbeenapowerfailure.
• Theappliancedoorisnotshutproperly.
• ADelayTimerhasbeenset.
• DRYINGisintheOFF position.
12
GB
Before calling for Assistance:
• Check whether you can solve the problem alone (see “Troubleshooting”);
• Restarttheprogrammetocheckwhethertheproblemhasbeensolved;
• Ifthisisnotthecase,contactanauthorisedTechnicalAssistanceCentreusingthetelephonenumberprovidedonthe
guarantee certificate.
! Always request the assistance of authorised technicians.
Have the following information to hand:
• thetypeofproblem;
• theappliancemodel(Mod.);
• theserialnumber(S/N).
This information can be found on the data plate applied to the rear of the washer-dryer, and can also be found on the front of
the appliance by opening the door.
Service
CZ
13
Česky
! Tento symbol vám připomíná potřebu
přečtení návodu k použití.
Obsah
Instalace, 14-15
Rozbalení a vyrovnání do vodorovné polohy
Připojení k elektrické a k vodovodní síti
První prací cyklus
Technické údaje
Údržba a péče, 16
Uzavření přívodu vody a vypnutí elektrického napájení
Čištění pračky
Čištění dávkovače pracích prostředků
Péče o dvířka a buben
Čištění čerpadla
Kontrola přítokové hadice na vod
Opatření a rady, 17
Základní bezpečnostní pokyny
Likvidace
Manuální otevření dvířeku
Popis pračky, 18-19
Ovládací panel
Displej
Jak provést prací cyklus nebo cyklus
suše, 20
Programy a funkce, 21
Tabulka pracích programů
Funkce praní
Prací prostředky a prádlo, 22
Dávkovač pracích prostředků
Příprava prádla
Speciální programy
Systém automatického vyvážení náplně
Poruchy a způsob jejich odstranění, 23
Servisní služba, 24
CZ
Návod k použití
PRAČKA
RDPD 117607 J
14
CZ
Instalace
Dokonalé vyrovnání do vodorovné polohy
zabezpečí stabilitu zařízení a zamezí vzniku
vibrací a hluku během činnosti. V případě
instalace na podlahovou krytinu nebo na
koberec nastavte nožky tak, aby pod pračkou
zůstal dostatečný volný prostor pro ventilaci.
Připojení k elektrické a k vodo-
vodní síti
Připojení přítokové hadice vody
1. Připojte ke ko-
houtku studené
vody s hrdlem se
závitem 3/4 pro plyn
zařízení A, a poté
k němu připojte
zašroubováním
přívodní hadici.
Před připojením
hadice nechte vodu
odtékat, dokud ne-
bude čirá. Pro správnou instalaci zařízení
dodržte návod, který je součástí balení.
! Zařízení je již nastaveno tak, aby
umožňovalo správnou činnost pračky se
sušičkou, a proto se doporučuje neměnit
jeho nastavení.
2. Připojte přítokovou
hadici k pračce
prostřednictvím
příslušné přípojky
na vodu, umístěné
vpravo nahoře (viz
obrázek).
3. Dbejte na to, aby hadice nebyla příliš oh-
nutá ani stlačená.
! Tlak v rozvodu vody se musí pohybovat
v rozmezí hodnot uvedených v tabulce s
technickými údaji (viz vedlejší strana).
! V případě, že délka přítokové hadice ne-
bude dostatečná, obraťte se na specializo-
vanou prodejnu nebo na autorizovaný tech-
nický personál.
! Nikdy nepoužívejte již použité hadice.
! Používejte hadice z příslušenství zařízení.
! Je důležité uschovat tento návod tak, aby-
ste jej mohli kdykoli konzultovat. V případě
prodeje, darování nebo přestěhování pračky
se ujistěte, že zůstane uložen v blízkosti
pračky, aby mohl posloužit novému majiteli
při seznámení s její činností a s příslušnými
upozorněními.
! Pozor si přečte uvede pokyny: ob-
sahují důležité informace týkající se instalace,
použití a bezpečnosti při práci.
Rozbalení a vyrovnání do vodoro-
vné polohy
Rozbalení
1. Rozbalte pračku.
2. Zkontrolujte, zda během přepravy
nedošlo k jejímu poškození. V případě, že
je poškozena, ji nezapojujte a obraťte se na
prodejce.
3. Odstraňte 4
šrouby chránící
před poškozením
během přepravy a
gumovou podložku
s příslušnou
rozpěrkou, které se
nacházejí v zadní
části (viz obrázek).
4. Uzavřete otvory po šroubech plastovými
krytkami z příslušenství.
5. Uschovejte všechny díly: v případě
opětovné přepravy pračky je bude třeba na-
montovat zpět.
! Obaly nejsou hračky pro děti!
Vyrovnání do vodorovné polohy
1. Pračku je třeba umístit na rovnou a pe-
vnou podlahu, aniž by se opírala o stěnu,
nábytek či něco jiného.
2. V případě, že
podlaha není do-
konale vodorovná,
mohou být případné
rozdíly vykompenzo-
vány šroubováním
předních nožek (viz
obrázek); Úhel sklo-
nu, naměřený na pra-
covní ploše, nesmí
přesáhnout 2°.
A
CZ
15
Připojení vypouštěcí hadice
Připojte vypouštěcí
hadici, aniž byste ji
ohýbali, k odpado-
vému potrubí nebo
k odpadu ve stěně,
který se nachází od
65 do 100 cm nad
zemí;
nebo ji uchyťte k
okraji umývadla či
vany a připevněte
vodicí držák
z příslušenství ke
kohoutu (viz obrá-
zek). Volný konec
vypouštěcí hadi-
ce nesmí zůstat
ponořený do vody.
! Použití prodlužovacích hadic se
nedoporučuje; je-li však nezbytné,
prodlužovací hadice musí mít stejný průměr
jako originální hadice a její délka nesmí
přesáhnout 150 cm.
Připojení k elektrické síti
Před zasunutím zástrčky do zásuvky se
ujistěte, že:
Je zásuvka uzemněna a že vyhovuje nor-
mám;
je zásuvka schopna snést maximální zátěž
odpovídající jmenovitému příkonu zařízení,
uvedenému v tabulce s technickými údaji
(viz vedle);
hodnota napájecího napětí odpovídá
údajům uvedeným v tabulce s technickými
údaji (viz vedle);
je zásuvka kompatibilní se zástrčkou
pračky. V opačném případě je třeba
vyměnit zásuvku.
! Pračka nesmí být umístěna venku – pod
širým nebem, a to ani v případě, že by se
jednalo o místo chráněné před nepřízní
počasí, protože je velmi nebezpečné vystavit
ji působení deště a bouří.
! Po denitivní instalaci pračky musí zásuvka
zůstat snadno přístupná.
! Nepoívejte prodlovací kabely a rozvodky.
! Kabel nesmí být ohnutý ani stlačený.
! Výměna kabelu musí být svěřena výhradně
65 - 100 cm
autorizovanému technickému personálu.
Upozornění! Výrobce neponese žádnou
odpovědnost za následky nerespektování
uvedených předpisů.
První prací cyklus
Po instalaci zařízení je třeba ještě předtím,
než je použijete na praní prádla, provést jeden
zkušební cyklus s pracím prostředkem a bez
náplně prádla nastavením pracího programu
samočištění (viz “Čištění pračky”).
Technické údaje
Model RDPD 117607 J
Rozmìry
šíøka 59,5 cm
výška 85 cm
hloubka 60,5 cm
Kapacita
od 1 do 11 kg pro praní
od 1 do 7 kg pro sušení
Napájení
Viz štítek s technickými
údaji, aplikovaný na zarí-
zení.
ipojení k
rozvodu vody
maximální tlak
1 MPa (10 bar)
minimální tlak
0.05 MPa (0.5 bar)
kapacita bubnu 71 litrù
Rychlost
odstøování
a¡z do 1600 otáèek za
minutu
Kontrolní
program po-
dle normy
EN 50229
praní: program 8; teplota
60°; náplò 11 kg prádla.
suše: větší náplň
(7 kg) musí být vysušena
volbou úrovně sušení
„EXTRA“; zbytek náplně
musí být vysušen volbou
sušení úrovně „EXTRA“:
náplň musí být tvořena 3
prostěradly a 7 povlaky.
Toto zaøízení odpovídá
následujícím normám
Evropské unie:
- 2004/108/CE (Elektro-
magnetická kompatibilita)
- 2006/95/CE (Nízké napìtí)
- 2012/19/EU (WEEE)
Hluènost
(dB(A) re
1 pW)
Praní: 54
Odstøeïování: 83
Sušení: 63
16
CZ
Údržba a péče
Čištění čerpadla
Součástí pračky je samočisticí čerpadlo,
které nevyžaduje údržbu. Může se však stát,
že se v jeho vstupní části, určené k jeho
ochraně a nacházející se v jeho spodní části,
zachytí drobné předměty (mince, knoíky).
! Ujistěte se, že byl prací cyklus ukončen, a
vytáhněte zástrčku ze zásuvky.
Přístup ke vstupní části čerpadla:
1. pomo-
cí šroubováku
odstraňte krycí pa-
nel nacházející se v
přední části pračky
(viz obrázek);
2. Odšroubujte víko
jeho otáčením proti
směru hodinových
ručiček (viz obrázek):
vytečení malého
množství vody je
zcela běžným jevem;
3. dokonale vyčistěte vnitřek;
4. zašroubujte zpět víko;
5. namontujte zpět panel, přičemž se před
jeho přisunutím k zařízení ujistěte, že
došlo ke správnému zachycení háčků do
příslušných podélných otvorů.
Kontrola přítokové hadice na vodu
Stav přítokové hadice je třeba zkontrolovat
alespoň jednou ročně. Jsou-li na ní viditel-
né praskliny nebo trhliny, je třeba ji vyměnit:
silný tlak působící na hadici během pracího
cyklu by mohl způsobit její náhlé roztržení.
! Nikdy nepoužívejte již použité hadice.
Uzavření přívodu vody a vypnutí
elektrického napájení
Po každém praní uzavřete přívod vody.
Tímto způsobem dochází k omezení
opotřebení pračky a ke snížení nebezpečí
úniku vody.
Před zahájením čištění pračky a během
operací údržby vytáhněte zástrčku
napájecího kabelu z elektrické zásuvky.
Čištění pračky
• Vnější části a části z gumy se mohou čistit
hadrem navlhčeným ve vlažné vodě a sa-
ponátu. Nepoužívejte rozpouštědla ani abra-
zivní látky.
• Pračka je vybavena programem
samočištění vnitřních částí, který musí být
proveden bez jakéhokoli druhu náplně v
bubnu.
Prací prostředek (množství rovnající se
10% množství doporučeného pro částečně
znečištěné prádlo) nebo specické přídavné
prostředky pro čištění pračky budou moci být
použity jako pomocné prostředky v pracím
programu. Doporučuje se provést samočisticí
program každých 40 cyklů praní.
Pro aktivaci programu stiskněte tlačítko na
5 sekund a poté stiskněte tlačítko START/
PAUZA; dojde k zahájení programu, který
bude trvat přibližně 70 minut.
Čištění dávkovače pracích
prostředků
Vytáhněte dávkovač
jeho nadzvednutím
a vytažením směrem
ven (viz obrázek).
Umyjte jej pod prou-
dem vody; tento druh
vyčištění je třeba
provádět pravidelně.
Péče o dvířka a buben
Dvířka ponechte pokaždé pootevřená, aby
se zabránilo tvorbě nepříjemných zápachů.
CZ
17
Opatření a rady
! Pračka byla navržena a vyrobena v souladu s platmi me-
zirodními bezpečnostním předpisy. Tato upozorně jsou uděna
z bezpečnostních důvodů a je třeba si je pozorně příst.
Základní bezpečnostní pokyny
Toto zařízení bylo navrženo výhrad pro poití v domácnosti.
Toto zařízení mohou používat děti od 8 let a
osoby se sníženými fyzickými, senzorickými
nebo duševními schopnostmi nebo osoby s
nedostatečmi zkušenostmi a znalostmi,
když se nacházejí pod náležitým dohledem
nebo když byly náležitě vyškoleny ohledně
bezpečho použití zařízení a uvědomují
si související nebezpečí. Děti si nesmí
hrát se zařízením. Děti nesmí provádět
operace údržby a čištění bez dohledu.
– Nesušte nevyprané oblečení.
Oblečení znečištěné látkami, jako je olej z vaření,
aceton, líh, benzin, kerosen, odstraňovače skvrn,
terpenn, vosk a látky na jeho odstranění, se
musí před sušením v sušičce prádla vyprat v teplé
vodě s vyšším množstvím pracího prostředku.
edměty jako pěnová guma (latexová
pěna), sprchové čepice, nepromokavé textil-
látky, výrobky s jednou stranou z gumy a
šaty nebo polštáře, které mají části z latexo-
gumy, se nesmí sušit v sušičce prádla.
Aviváž nebo podobné prostředky se musí
používat v souladu s pokyny výrobce.
Závěrečná část cyklu sušičky prád-
la pobí bez tepla (chladi cyklus), aby
se zabránilo poškoze sušeného prádla.
UPOZORNĚNÍ: Nikdy nezastavujte sušičku prádla
před ukončením programu sušení. V takovém
případě rychle vyjměte všechno prádlo ze sušičky
a pověste jej, aby se rychle ochladilo.
Pračku mohou používat pouze dospělé osoby podle pokynů
uvedených v tomto návodu.
Nedotýkejte se zařízení bosí nebo v případě, že máte mokré
ruce či nohy.
Nevytahujte zástrčku ze zásuvky tahem za kabel, ale ucho-
pením za zástrčku.
Neotvírejte dávkovač pracích prostředků během činnosti
zařízení.
Nedotýkejte se odčerpávané vody, protože může mít velmi
vysokou teplotu.
Nepokoušejte se o násilné otevření dvířek: mohlo by dojít
k poškození bezpečnostního uzávěru, který zabraňuje
náhodnému otevření.
Při výskytu poruchy se v žádném případě nepokoušejte o
opravu vnitřních částí zařízení.
Vždy mějte pod kontrolou děti a zabraňte tomu, aby se
přibližovaly k zařízení během pracího cyklu.
Během pracího cyklu mají dvířka tendenci ohřát se.
V přípa poeby přemísťujte pračku ve dvou nebo ve
ech a nujte ce operaci maximálpozornost. Nikdy se
nepokoušejte zařízeemíovat sami, je totvelmi těžké.
Před zahájením vkládání prádla zkontrolujte, zda je buben prázdný.
Nepoužívejte toto zařízení k sušení oděvů, které
byly čištěny hořlavými látkami (např. trichloretylénem).
Nepoužívejte toto zařízení k sušení molita-
nu a podobných elastomerů.
Ujistěte se, že během cyklu sušení je vo-
dovodní kohoutek otevřený.
Tato pračka se sušičkou může být používána pouze k
sušení oděvů, které byly předtím vyprány ve vodě.
Vyjměte z kapes všechny předměty, jako
jsou zapalovače a zápalky
Pokud nejsou ti mladší 3 let pod neustálým
dozorem, mu být udržovány v dostatečné
vzlenosti od sušičky-
Likvidace
Likvidace obalových materiálů:
při jejich odstranění postupujte v souladu s místním předpisy
a dbejte na možnou recyklaci.
Evropská směrnice 2012/19/ES o odpadu tvořeném elektrickými
a elektronickými zařízeními nařizuje, že elektrospotřebiče nesmí
být likvidovány v rámci běžného pevného městského odpadu.
Vazená zařízení mu t shrožna zvšť za účelem
zvýšení počtu recyklovach a znovupoužitých materiálů, z nichž
jsou složena, a z důvodu zabránění možných ublížení na zdraví a
škod na životním prostředí. Symbolem je přeškrtnutý koš, uvedený
na všech výrobcích s cílem připomenout povinnosti spoje se se-
parovaným sběrem. Podrobnější informace týkající se správného
způsobu vyřazení elektrospotřebičů z provozu mohou jejich držitelé
získat tak, že se obrátí na navrženou veřejnou instituci nebo na
prodejce.
Manuální otevření dvířek
V případě, že není možné otevřít dvířka s průzorem
z důvodu výpadku elektrické energie a hodláte pověsit
prádlo, postupujte následovně:
1. vytáhněte zástrčku ze zásuvky elektrické sítě.
2. Zkontrolujte, zda je hladina vody uvnitř zařízení nižší,
než je úroveň otevření dvířek; v opačném případě vypusťte
přebytečnou vodu vypouštěcí hadicí a zachyťte ji do vědra,
jak je znázorněno na obrázku.
3. pomocí šroubováku odstraňte krycí panel nacházející se
v přední části pračky (viz obrázek).
4. s použitím jazýčku označeho na obrázku pohněte srem
ven z dorazu plasto hlo do jeho uvolnění; násled jej
pohněte srem do a soas otevřete dvířka.
5. namontujte zpět panel, přičemž se před jeho přisunutím
k zařízení ujistěte, že došlo ke správnému zachycení háčků
do příslušných podélných otvorů.
20
18
CZ
Dávkovač pracích prostředků: slouží k dávkování
pracích prostředků a přídavných prostředků (viz „Prací
prostředky a prádlo“).
Funkční popis
: uvnitř zásuvky dávkovače pracích
prostředků se nachází funkční popis, na kterém jsou
uvedeny všechny dostupné programy spolu s grackou
příručkou o použití jednotlivých přihrádek zásuvky.
Tlačítko ON/OFF : zapněte nebo vypněte pračku
krátkým stisknutím tlačítka. Kontrolka START/PAUZA
pomalu blikající zeleným světlem poukazuje na to, že je
stroj zapnutý. Za účelem vypnutí pračky během praní je
třeba držet tlačítko stisknuté déle, přibližně 3 sek.; krátké
nebo náhodné stisknutí neumožní vypnutí pračky. Vyp-
nutí zařízení během praní způsobí zrušení probíhajícího
pracího programu.
OTOČNÝ OVLADAČ PROGRAMŮ: Slouží k nastavení
požadovaného programu (viz “Tabulka programů“).
FUNKČNÍ Tlačítko: stiskněte tlačítko kvůli volbě
požadované funkce. Na displeji se rozsvítí příslušná
kontrolka.
Tlačítko
SAMOČIŠTĚNÍ: stiskněte jej, když chcete
provést čištění vnitřních částí zařízení
(viz “Čištění
pračky”).
Tlačítka
DIRECT INJECTION
: jeho stisknutím se pro-
vádí volba volitelné funkce DIRECT INJECTION.
Tlačítko
OPAKOVANÉ MÁCHÁNÍ
: jeho stisknutím
můžete provést volbu požadovaného máchání.
Tlačítko ODSTŘEĎOVÁNÍ : stiskněte za účelem
snížení nebo úplného vyloučení odstřeďování - hodnota
bude uvedena na displeji.
Tlítko
TEPLOTA
: stiskněte za účelem snížení te-
ploty: Příslušná hodnota bude zobrazena na displeji.
Tlačítko SUŠENÍ : Jeho stisknutí slouží k omezení
nebo úplnému vyloucení sušení; zvolená úroven nebo
doba sušení bude zobrazena na displeji
Tlačítko SAMOSTATNÉ SUŠENÍ : stisknutím spu-
stíte pouze fázi sušení.
Tlačítko
ZABLOK. TLAČÍTEK
: aktivace
zablokování ovládacího panelu se provádí tak, že
podržíte stisknuté tlačítko přibližně na 2 sekundy. Když
se na displeji zobrazí nápis „ZABLOK. TLAČÍTEK
AKTIVNÍ“, ovládací panel je zablokován (s výjimkou
tlačítko ON/OFF). Tímto způsobem se zamezí náhodným
změnám programů, zejména když jsou v domácnosti
děti. Zrušení zablokování ovládacího panelu se provádí
tak, že podržíte stisknuté tlačítko přibližně na 2 sekundy.
Tlačítko
ODLOŽENÝ START
: stiskněte za účelem
nastavení odloženého startu zvoleného programu. Doba,
o kterou bude start odložen, bude zobrazena na displeji.
Tlačítko s kontrolkou START/PAUZA: když zelená
kontrolka začne pomalu blikat, stiskněte toto tlačítko pro
zahájení praní. Po zahájení cyklu se kontrolka rozsvítí
stálým světlem. Přejete-li si přerušit praní, opětovně
stiskněte tlačítko; kontrolka bude blikat oranžovým
světlem. Když symbol není rozsvícen, je možné
otevřít dvířka. Za účelem opětovného zahájení cyklu
z místa, v němž byl přerušen, opětovně stiskněte tlačítko.
Pohotovostní režim
Za účelem shody s novými předpisy souvisejícími s
energetickou úsporou je tato pračka vybavena systémem
automatického vypnutí (přechodu do pohotovostního
režimu – standby), který je aktivován po uplynutí 30 mi-
nut, když se pračka nepoužívá. Krátce stiskněte tlačítko
ON/OFF a vyčkejte na obnovení činnosti zařízení.
Spotřeba v off-mode: 0,5 W
Spotřeba v Left-on: 8 W
Popis pračky
Ovládací panel
FUNKČNÍ
Tlačítko
Tlačítko
ON/OFF
Dávkovač pracích
prostředků
Tlačítko
TEPLOTA
Tlačítko
ODSTŘEĎOVÁNÍ
Tlačítko
SAMOČIŠTĚNÍ
Tlačítko
ODLOŽENÝ
START
Tlačítko
ZABLOK.
TLAČÍTEK
Funkční popis
Tlačítko
DIRECT
INJECTION
Tlačítko
OPAKOVANÉ
MÁCHÁNÍ
Tlačítko s kontrolkou
START/PAUZA
Displej
OTOČNÝ OVLADAČ
PROGRAMŮ
Tlačítko
SAMOSTATNÉ SUŠENÍ
Tlačítko
SUŠENÍ
CZ
19
Displej
Displej slouží k naprogramování zařízení a poskytuje četné informace.
Na ploše A se zobrazí ikona a zvolený program, fáze praní a sušení, jakož i doba zbývající do konce cyklu.
Na ploše B jsou zobrazeny dvě úrovně intenzity týkající se volitelné funkce DIRECT INJECTION.
Na plochách C se nacházejí kontrolky týkající se dostupných funkcí.
Na ploše D je zobrazena doba zbývající do spuštění zvoleného programu v případě nastavení funkce ODLOŽENÝ
START.
V řetězci E je zobrazena maximální hodnota rychlosti odstřeďování, které zařízení může dosáhnout na základě zvo-
leného programu; když program nepočítá s nastavením odstřeďování, na uvedené ploše je zobrazen symbol “--” s
nízkým jasem.
Na ploše F je zobrazena hodnota teploty, kterou lze zvolit na základě zvoleného programu; když není nastavení teploty
součástí zvoleného programu, na uvedené ploše je zobrazen symbol “--” s nízkým jasem.
Symbol Zablokovaných dvířek
Rozsvícení uvedeného symbolu poukazuje na zablokování dvířek kvůli zabránění jejich náhodnému otevření. Aby se
předešlo poškození, před otevřením dvířek je třeba vyčkat na zhasnutí uvedeného symbolu.
POZN.: Když je aktivována funkce ODLOŽENÝ START, nebude možné otevřít dvířka a pro jejich otevření bude třeba
přerušit činnost zařízení stisknutím tlačítka START/PAUZA.
! Při prvním zapnutí budete vyzváni, abyste provedli volbu jazyka, a poté bude na displeji automaticky zvoleno menu
volby jazyka.
Za účelem volby požadovaného jazyka stiskněte tlačítka X a Y a potvrďte voblu stisknutím tlačítka Z.
Když si přejete provést změnu jazyka, vypněte zařízení, stiskněte současně tlačítka G, H, I a držte je stisknutá, dokud
neuslyšíte akustický signál a neobjeví se menu pro volbu jazyka.
! Když si přejete změnit jas displeje, který je v rámci přednastavení nastaven na nejvyšší hodnotu, vypněte zařízení, při
jeho opětovném zapnutí stiskněte současně tlačítka G, L a M a držte je stisknuta, dokud neuslyšíte akustický signál.
Stisknutím tlačítek X a Y zvolte požadovaný jas a potvrďte volbu stisknutím tlačítka Z.
! Když během pracího cyklu nebo při nastavování funkce „ODLOŽENÝ START“ nebude displej používán po dobu 1
minuty, bude aktivován „SPOŘIČ OBRAZOVKY“. Pro návrat na předchozí zobrazení stačí stisknout kterékoli tlačítko.
2:55
90°
1200
-- h
--
COTONE
H
G
Y
X Z
I
L M
A
B
C
C
D
E
C
F
20
CZ
Jak provést prací cyklus nebo
cyklus sušení
1. ZAPNUTÍ ZAŘÍZENÍ. Stiskněte tlačítko a na displeji
se zobrazí nápis HOTPOINT; kontrolka START/PAUZA
bude pomalu blikat zelenou barvou.
2. NAPLŇTE PRAČKU PRÁDLEM. Otevřete dvířka.
Naplňte pračku prádlem a dbejte přitom, aby nedošlo
k překročení množství náplně, uvedeného v tabulce
programů na následující straně.
3. DÁVKOVÁNÍ PRACÍHO PROSTŘEDKU. Vytáhněte
dávkovač pracích prostředků a naplňte prací prostředek
do příslušných přihrádek způsobem vysvětleným v části
„Prací prostředky a prádlo“.
4. ZAVŘETE DVÍŘKA.
5. ZVOLTE PRACÍ PROGRAM. Otočným ovladačem
PROGRAMŮ zvolte požadovaný program; název
programu bude zobrazen na displeji; ke zvolenému
programu je přiřazena teplota a rychlost odstřeďování,
které se dají měnit. Na displeji bude zobrazena doba
trvání cyklu.
6. PROVEĎTE UŽIVATELSKÁ NASTAVENÍ PRACÍHO
CYKLU. Použijte příslušná tlačítka:
Změňte teplotu a/nebo odstřeďování. Zařízení
automaticky zvolí teplotu a maximální rychlost
odstřeďování přednastavené pro zvolený program;
tyto hodnoty se nesmí zvyšovat. Stisknutím tlačítka
je možné postupně snížit teplotu až po praní ve
studené vodě (na displeji se zobrazí symbol “--”).
Stisknutím tlačítka je možné postupně snížit rychlost
odstřeďování až po jeho úplné vyloučení (na displeji
se zobrazí symbol “--”). Další stisknutí tlačítek obnoví
nastavení maximálních přednastavených hodnot.
! Výjimka: při volbě programu 5 bude možné zvýšit
teplotu až na 40°C.
! Výjimka: při volbě programu 7 bude možné zvýšit teplo-
tu až na 90°C.
! Výjimka: při volbě programu 9 bude možné zvýšit teplo-
tu až na 60°C.
Nastavte odložený start.
Pro nastavení odloženého startu zvoleného programu
stiskněte příslušné tlačítko až do dosažení požadované
doby odložení. Zrušení odloženého startu se provádí
stisknutím tlačítka až do zobrazení nápisu “-- h”.
Nastavení sušení
Jedním nebo několikanásobným stisknutím tlačítka
SUŠENÍ se nastavuje požadovaný druh sušení.
K dispozici jsou dvě možnosti:
A - Na základě požadované úrovně sušení:
K Žehlení: Určené pro kusy oblečení, které se následně
musí žehlit. Úroveň zbytkové vlhkosti zjemní záhyby a
usnadní jejich odstranění.
K zavěšení: Ideální pro ty kusy oblečení, které
nevyžadují úplné vysušení.
K uložení: Vhodné pro prádlo, které je určeno k uložení
do skříně bez potřeby žehlení.
Extra: Vhodné pro kusy oblečení, které vyžadují úplné
vysušení, jako jsou froté ručníky a župany.
B - Podle nastavené doby: od 30 do 180 minut.
Vyloučení sušení se provádí tisknutím příslušného
tlačítka až do zobrazení nápisu OFF na displeji.
Když je množství prádla ve výjimečných případech vyšší
než maximální povolená náplň, proveďte prací cyklus, po
jeho ukončení prádlo rozdělte a jednu ze dvou častí vložte
zpět do bubnu. Dále se řiďte pokyny pro samostat
sušení. Zopakujte stejný postup i při sušení zbývající části
prádla. Na konci cyklu sušení proběhne fáze ochlazování.
Samostatné sušení
Stiskněte tlačítko kvůli provedení samotného sušení.
Po provedení volby požadovaného programu, který
je kompatibilní s vloženým druhem prádla, dojde při
stisknutí tlačítka k vyloučení fáze praní a bude
aktivováno sušení s maximální úrovní určenou pro
zvolený program. Je možné změnit a nastavit úroveň
nebo dobu trvání sušení stisknutím tlačítka sušen .
(Není kompatibilní s programy 1-2-3-4-14).
Nastavte druh máchání.
Volitelná funkce umožňuje zvolit požadovaný druh
máchání pro maximální péči o citlivé druhy pokožky. Při
prvním stisknutí tlačítka bude nastavena úroveň “Extra
+1”, která umožní provést volbu přídavného máchání
ve srovnání se standardním mácháním cyklu, aby se
odstranily všechny stopy po pracím prostředku. Při
druhém stisknutí tlačítka bude nastavena úroveň „Extra
+2“, která umožňuje provést volbu dvou přídavných
máchání ve srovnání se standardním mácháním cyklu a
doporučuje se pro citlivější pokožky. Při třetím stisknutí
tlačítka bude nastavena úroveň „Extra +3“ máchání,
která umožní provést volbu 3 přídavných máchání ve
srovnání se standardním mácháním cyklu. Tato volitelná
funkce, která je aktivována při cyklech s teplotou 40 °C,
umožňuje odstranit hlavní alergeny, jako je kočičí i psí
srst a pyl. Při teplotě nad 40°C se dosahuje optimální
úrovně protialergické ochrany. Opětovným stisknutím
tohoto tlačítko se můžete vrátit na úroveň máchání
Běžné máchání“. Když není možné provést požadované
nastavení nebo změnit existující nastavení, na displeji se
zobrazí „NEPOUŽITELNÝ“ nebo „NEMĚNITELNÝ“.
Změňte vlastnosti cyklu.
Stiskněte tlačítka aktivace funkce; rozsvítí se
odpovídající kontrolka.
Opětovným stisknutím můžete zvolenou funkci zrušit;
zhasne se odpovídající kontrolka.
! Když zvolená funkce není kompatibilní s nastaveným
programem, příslušná kontrolka bude zobrazena s
nízkým jasem a nekompatibilita bude signalizována také
akustickým signálem (3 pípnutí) a zobrazením nápisu
NEPOUŽITELNÝ na displeji.
! Když zvolená funkce není kompatibilní s další,
předtím nastavenou funkcí, na displeji se zobrazí nápis
NEPOUŽITELNÝ a funkce nebude aktivována.
! Funkce mohou změnit doporučenou náplň a/nebo dobu
trvání cyklu.
7. SPUSŤTE PROGRAM. Stiskněte tlačítko START/
PAUZA. Příslušná kontrolka se rozsvítí stálým zeleným
světlem a dojde k zablokování dvířek (rozsvícený symbol
ZABLOKOVANÝCH DVÍŘEK ). Během praní se na
displeji zobrazí název probíhající fáze. Za účelem změny
programu během probíhajícího cyklu přerušte činnost
pračky stiknutím tlačítka START/PAUZA (kontrolka
START/PAUZA bude pomalu blikat oranžovým světlem);
zvolte požadovaný cyklus a opětovně stiskněte tlačítko
START/PAUZA. Za účelem otevření dvířek v průběhu
pracího cyklu stiskněte tlačítko START/PAUZA; když
bude symbol ZABLOKOVANÝCH DVÍŘEK zhasnutý,
bude možné otevřít dvířka. Opětovným stisknutím tlačítka
START/PAUZA znovu uveďte do činnosti prací program
z bodu, ve kterém byl přerušen.
8. UKONČENÍ PROGRAMU. Bude oznámeno zobrazením
nápisu „KONEC CYKLU“ na displeji. Po zhasnutí symbolu
ZABLOKOVANÝCH DVÍŘEK bude možné otevřít
dvířka. Otevřete dvířka, vyložte prádlo a vypněte zařízení.
! Přejete-li si zrušit již zahájený cyklus, znovu dlouze
stiskněte tlačítko . Cyklus bude přerušen a dojde k
automatickému vypnutí zařízení.
Direct Injection
Pračka je vybavena inovační technologií «Direct Injection»,
která připravuje směs vody s pracím prostředkem, čímž ihned
aktivuje čisticí účinky pracího prostředku. Tato aktivní emulze
se vpouští přímo do bubnu pračky, účinně proniká do vláken
a odstraňuje i ty nejodolnější nečistoty již při nízkých teplo-
tách, přičemž bere maximální ohled na barvy a tkaniny. Je
možné zvolit režim «Výkon» pro dosažení větší čistoty nebo
režim «EcoEnergy» pro dosažení úspory energie.
1 / 1

HOTPOINT/ARISTON RDPD 117607 JD EU Užívateľská príručka

Kategória
Práčky
Typ
Užívateľská príručka