Indesit EWDE 71280 W EU Užívateľská príručka

1

GB

Contents

Installation, 2-3

Unpacking and levelling

Connecting the electricity and water supplies

The first wash cycle

Technical data

Care and maintenance, 4

Cutting off the water or electricity supply

Cleaning the Washer-dryer

Cleaning the detergent dispenser drawer

Caring for the door and drum of your appliance

Cleaning the pump

Checking the water inlet hose

Precautions and tips, 5

General safety

Disposal

Description of the Washer-dryer, 6-7

Control panel

Display

How to run a wash cycle or a drying cycle, 8

Wash cycles and options, 9

Table of wash cycles

Wash options

Detergents and laundry, 10

Detergent dispenser drawer

Preparing the laundry

Fast daily cycles

Special wash cycles

Load balancing system

Troubleshooting, 11

Service, 12

EWDE 71280

Instructions for use

WASHER-DRYER

English,1

GB

! This symbol reminds you to read this instruction

manual.

ES

CZ

BG

SK

UA

SR

Español,13

Česky,25

Slovensky,37

Български,49

Українська,61

Cрпски,73

2

GB

Installation

! This instruction manual should be kept in a safe

place for future reference. If the washing machine

is sold, transferred or moved, make sure that the

instruction manual remains with the machine so

that the new owner is able to familiarise himself/

herself with its operation and features.

! Read these instructions carefully: they contain

vital information relating to the safe installation

and operation of the appliance.

Unpacking and levelling

Unpacking

1. Remove the washing machine from its packaging.

2. Make sure that the washing machine has not

been damaged during the transportation process.

If it has been damaged, contact the retailer and do

not proceed any further with the installation process.

3. Remove the 4 pro-

tective screws (used

during transportation)

and the rubber washer

with the corresponding

spacer, located on the

rear part of the applian-

ce (see figure).

4. Close off the holes using the plastic plugs

provided.

5. Keep all the parts in a safe place: you will need

them again if the washing machine needs to be

moved to another location.

! Packaging materials should not be used as

toys for children.

Levelling

1. Install the washing machine on a flat sturdy

floor, without resting it up against walls, furniture

cabinets or anything else.

2. If the floor is not per-

fectly level, compensa-

te for any unevenness

by tightening or loo-

sening the adjustable

front feet (see figure);

the angle of inclination,

measured in relation to

the worktop, must not

exceed 2°.

Levelling the machine correctly will provide it with

stability, help to avoid vibrations and excessive

noise and prevent it from shifting while it is ope-

rating. If it is placed on carpet or a rug, adjust the

feet in such a way as to allow a sufficient venti-

lation space underneath the washing machine.

Connecting the electricity and wa-

ter supplies

Connecting the water inlet hose

1. Connect the supply

pipe by screwing it to

a cold water tap using

a ¾ gas threaded con-

nection (see figure).

Before performing the

connection, allow the

water to run freely until

it is perfectly clear.

2. Connect the inlet

hose to the washing

machine by screwing

it onto the correspon-

ding water inlet of the

appliance, which is si-

tuated on the top right-

hand side of the rear

part of the appliance

(see figure).

3. Make sure that the hose is not folded over

or bent.

! The water pressure at the tap must fall within

the values indicated in the Technical details table

(see next page).

! If the inlet hose is not long enough, contact a

specialised shop or an authorised technician.

! Never use second-hand hoses.

! Use the ones supplied with the machine.

3

GB

65 - 100 cm

Connecting the drain hose

Connect the drain

hose, without bending

it, to a drainage duct or

a wall drain located at a

height between 65 and

100 cm from the floor;

alternatively, rest it on

the side of a washba-

sin or bathtub, faste-

ning the duct supplied

to the tap (see figure).

The free end of the

hose should not be

underwater.

! We advise against the use of hose extensions;

if it is absolutely necessary, the extension must

have the same diameter as the original hose and

must not exceed 150 cm in length.

Electrical connections

Before plugging the appliance into the electricity

socket, make sure that:

•the socketisearthed and complieswith all

applicable laws;

•thesocketisabletowithstandthemaximum

power load of the appliance as indicated in the

Technical data table (see opposite);

•thepowersupplyvoltagefallswithinthevalues

indicated in the Technical data table (see opposite);

•thesocketiscompatiblewiththeplugofthe

washing machine. If this is not the case, repla-

ce the socket or the plug.

! The washing machine must not be installed

outdoors, even in covered areas. It is extremely

dangerous to leave the appliance exposed to

rain, storms and other weather conditions.

! When the washing machine has been installed,

the electricity socket must be within easy reach.

! Do not use extension cords or multiple sockets.

! The cable should not be bent or compressed.

! The power supply cable must only be replaced

by authorised technicians.

Warning! The company shall not be held responsible

in the event that these regulations are not respected.

The first wash cycle

Once the appliance has been installed, and before

you use it for the first time, run a wash cycle with

detergent and no laundry, using the wash cycle

“Auto Clean” (see “Cleaning the washer-dryer”).

Technical data

Model

EWDE 71280

Dimensions

width 59,5 cm

height 85 cm

depth 53,5 cm

Capacity

from 1 to 7 kg for the wash

programme;

from 1 to 5 kg for the drying

programme

Electrical

connections

please refer to the technical

data plate fixed to the machine

Water con-

nection

maximum pressure 1 MPa

(10 bar)

minimum pressure 0.05 MPa

(0.5 bar)

drum capacity 58 litres

Spin speed

up to 1200 rotations per minute

Energy rated

programmes

according to

regulations

EN 50229

Wash: programme 10; tem-

perature 60°C; using a load

of 7 kg.

Drying: select the 10 wash

programme and set the

drying level to “A4”, for both

loads. The first drying cycle

must be carried out with the

nominal load.

This appliance conforms to

the following EC Directives:

- EMC 2014/30/EU (Electro-

magnetic Compatibility)

- 2012/19/EU - (WEEE)

- LVD 2014/35/EU Low

Voltage)

4

GB

Care and maintenance

Cutting off the water and electricity

supplies

•Turnoffthewatertapaftereverywashcycle.

This will limit wear on the hydraulic system inside

the Washer-dryer and help to prevent leaks.

•UnplugtheWasher-dryerwhencleaningitand

during all maintenance work.

Cleaning the Washer-dryer

•The outerparts andrubber componentsof

the appliance can be cleaned using a soft cloth

soaked in lukewarm soapy water. Do not use

solvents or abrasives.

•Thewasher-dryerhasa“AutoClean”program-

me for its internal parts that must be run with

no load in the drum.

For maximum performance you may want to

use either the detergent (i.e. a quantity 10% the

quantity specified for lightly-soiled garments)

or special additives to clean the washer-dryer.

We recommend running a cleaning programme

every 40 wash cycles.

To start the programme press buttons A and B

simultaneously for 5 seconds (see figure).

The programme will start automatically and will

last approximately 70 minutes.

Cleaning the detergent dispenser

drawer

Remove the dispenser

by raising it and pulling

it out (see figure).

Wash it under running

water; this operation

should be repeated

frequently.

Caring for the door and drum of

your appliance

•Alwaysleavetheportholedoorajarinorderto

prevent unpleasant odours from forming.

Cleaning the pump

The Washer-dryer is fitted with a self-cleaning

pump which does not require any maintenan-

ce. Sometimes, small items (such as coins or

buttons) may fall into the pre-chamber which

protects the pump, situated in its bottom part.

! Make sure the wash cycle has finished and

unplug the appliance.

To access the pre-chamber:

1. using a screwdriver,

remove the cover pa-

nel on the lower front

part of the Washer-

dryer (see figure);

2. unscrew the lid by

rotating it anti-clockwi-

se (see figure): a little

water may trickle out.

This is perfectly nor-

mal;

3. clean the inside thoroughly;

4. screw the lid back on;

5. reposition the panel, making sure the hooks

are securely in place before you push it onto the

appliance.

Checking the water inlet hose

Check the inlet hose at least once a year. If there

are any cracks, it should be replaced immedia-

tely: during the wash cycles, water pressure is

very strong and a cracked hose could easily

split open.

! Never use second-hand hoses.

A

B

5

GB

Precautions and tips

! This Washer-dryer was designed and constructed in ac-

cordance with international safety regulations. The following

information is provided for safety reasons and must therefore

be read carefully.

General safety

• This appliance can be used by children aged

from 8 years and above and persons with re-

duced physical, sensory or mental capabilities

or lack of experience and knowledge if they

have been given supervision or instruction

concerning use of the appliance in a safe way

and understand the hazards involved. Children

shall not play with the appliance. Cleaning

and user maintenance shall not be made by

children without supervision.

- Do not dry unwashed items in the tumble

dryer.

- Items that have been soiled with substances

such as cooking oil, acetone, alcohol, petrol,

kerosene, spot removers, turpentine, waxes

and wax removers should be washed in hot

water with an extra amount of detergent be-

fore being dried in the tumble dryer.

- Items such as foam rubber (latex foam),

shower caps, waterproof textiles, rubber ba-

cked articles and clothes or pillows fitted with

foam rubber pads should not be dried in the

tumble dryer.

- Fabric softeners, or similar products, should

be used as specified by the fabric softener

instructions.

- The final part of a tumble dryer cycle occurs

without heat (cool down cycle) to ensure that

the items are left at a temperature that ensures

that the items will not be damaged.

WARNING: Never stop a tumble dryer before

the end of the drying cycle unless all items are

quickly removed and spread out so that the

heat is dissipated.

•Thisappliancewasdesignedfordomesticuseonly.

•Donottouchthemachinewhenbarefootorwithwetor

damp hands or feet.

•Donotpullonthepowersupplycablewhenunplugging

the appliance from the electricity socket. Hold the plug

and pull.

•Do not open the detergent dispenserdrawer while the

machine is in operation.

•Donottouchthedrainedwaterasitmayreachextremely

high temperatures.

•Neverforcetheportholedoor.Thiscoulddamagethesafety

lock mechanism designed to prevent accidental opening.

•Iftheappliancebreaksdown,donotunderanycircum-

stances access the internal mechanisms in an attempt to

repair it yourself.

•Alwayskeepchildrenwellawayfromtheappliancewhile

it is operating.

•Thedoorcanbecomequitehotduringthewashcycle.

•Iftheappliancehastobemoved,workinagroupoftwo

or three people and handle it with the utmost care. Never

try to do this alone, because the appliance is very heavy.

•BeforeloadinglaundryintotheWasher-dryer,makesure

the drum is empty.

• Duringthedryingphase,thedoortendstogetquitehot.

• Donotusetheappliancetodryclothesthat

have been washed with flammable solvents

(e.g. trichlorethylene).

• Donotusetheappliancetodryfoamrubber

or similar elastomers.

• Makesurethatthewatertapisturnedonduringthedrying

cycles.

• Childrenoflessthan3yearsshouldbekept

away from the appliance unless continuou-

sly supervised.

• Removeallobjectsfrompocketssuchas

lighters and matches.

Disposal

•Disposingofthepackagingmaterials:observelocalregu-

lations so that the packaging may be re-used.

• The European Directive2012/19/EU (WEEE) on Waste

Electrical and Electronic Equipment, requires that old

household electrical appliances must not be disposed

of in the normal unsorted municipal waste stream. Old

appliances must be collected separately in order to op-

timise the recovery and recycling of the materials they

contain and reduce the impact on human health and the

environment. The crossed out “wheeled bin” symbol on

the product reminds you of your obligation, that when you

dispose of the appliance it must be separately collected.

Consumers should contact their local authority or retailer

for information concerning the correct disposal of their old

appliance.

6

GB

Detergent dispenser drawer: used to dispense deter-

gents and washing additives (see “Detergents and laundry”).

ON/OFF button : press this briefly to switch the machine

on or off. The START/PAUSE indicator light, which flashes

slowly in a green colour shows that the machine is switched

on. To switch off the Washer-dryer during the wash cycle,

press and hold the button for approximately 2 seconds; if

the button is pressed briefly or accidentally the machine will

not switch off. If the machine is switched off during a wash

cycle, this wash cycle will be cancelled.

WASH CYCLE knob: used to set the desired wash cycle

(see “Table of wash cycles”).

OPTION buttons with indicator light: used to select the

available options. The indicator light corresponding to the

selected option will remain lit.

SPIN button : press to reduce or completely exclude the

spin cycle - the value is indicated on the display.

TEMPERATURE button : press to decrease or comple-

tely exclude the temperature: the value will be shown on the

display.

DRYING button : press to decrease or exclude drying;

the selected drying level or time will appear on the display

(see “How to run a wash cycle or a drying cycle”).

START/PAUSE button with indicator light: when the

green indicator light flashes slowly, press the button to start

a wash cycle. Once the cycle has begun the indicator light

will remain lit in a fixed manner. To pause the wash cycle,

press the button again; the indicator light will flash in an

orange colour. If the symbol is not illuminated, the door

may be opened (wait approximately 3 minutes). To start the

wash cycle from the point at which it was interrupted, press

the button again.

Standby mode

This Washer-dryer, in compliance with new energy saving

regulations, is fitted with an automatic standby system which

is enabled after a few minutes if no activity is detected. Press

the ON-OFF button briefly and wait for the machine to start

up again.

Consumption in off-mode: 0,5 W

Consumption in Left-on: 8 W

Description of the Washer-dryer

Control panel

TEMPERATURE

Button

Detergent dispenser drawer

OPTION

buttons with

indicator lights

ON/OFF

button

SPIN SPEED

Button

START/PAUSE

button with indicator light

DISPLAY

DRYING

Button

WASH CYCLE

knob

7

GB

Display

The display is useful when programming the machine and provides a great deal of information.

The duration of the available programmes and the remaining time of a running cycle appear in section A; if the DELAY START

option has been set, the countdown to the start of the selected programme will appear. Furthermore, pressing the corre-

sponding button allows you to view the maximum temperature, spin speed and drying level or time values attained by the

machine during the selected cycle.

The phases scheduled for the selected cycle and, once the cycle has begun, the current phase of the wash cycle (and drying

cycle, if applicable) appear in section B.

Wash

Rinse

Spin / Drain

Drying

The icons corresponding to “temperature” , “Drying” and “spin” appear in section C from top to bottom:

If the symbol lights up, the display will visualise the set “temperature” value.

The symbol lights up while the drying settings are being adjusted.

If the symbol lights up, the display will visualise the set “spin” value.

Door locked symbol

The lit symbol indicates that the door is locked. To prevent any damage, wait until the symbol turns off before opening the

door (wait approximately 3 minutes).

To open the door while a cycle is in progress, press the START/PAUSE button; if the DOOR LOCKED symbol is switched

off the door may be opened (wait approximately 3 minutes).

B

CA

8

GB

How to run a wash cycle or a

drying cycle

1. SWITCH THE MACHINE ON. Press the button; the

START/PAUSE indicator light will flash slowly in a green

colour.

2. LOAD THE LAUNDRY. Open the porthole door. Load

the laundry, making sure you do not exceed the maximum

load value indicated in the table of programmes on the

following page.

3. MEASURE OUT THE DETERGENT. Pull out the

detergent dispenser drawer and pour the detergent into

the relevant compartments as described in “Detergents

and laundry”.

4. CLOSE THE DOOR.

5. SELECT THE WASH CYCLE. Set the WASH CYCLE

knob to the desired programme; a temperature and spin

speed is set for each wash cycle; these may be adjusted.

The duration of the cycle will appear on the display.

6. CUSTOMISE THE WASH CYCLE. Use the relevant

buttons:

Modifying the temperature and/or spin speed. The

machine automatically displays the maximum temperature

and spin speed values set for the selected cycle, or the

most recently-used settings if they are compatible with

the selected cycle. The temperature can be decreased by

pressing the button, until the cold wash “OFF” setting

is reached. The spin speed may be progressively reduced

by pressing the button, until it is completely excluded

(the “OFF” setting). If these buttons are pressed again, the

maximum values are restored.

! Exception: if the 2 programme is selected, the tempera-

ture can be increased up to a value of 60°C.

Setting the drying cycle

The first time the button is pressed, the machine will

automatically select the maximum drying cycle which is

compatible with the selected wash cycle. Subsequent

presses will decrease the drying level and then the drying

time, until the cycle is excluded completely (“OFF”).

Drying may be set as follows:

A- Based on the desired laundry dryness level:

Iron dry: suitable for clothes which will need ironing

afterwards. the remaining dampness softens creases,

making them easier to remove; “A1” appears on the display.

Hanger dry: ideal for clothes which do not need to be

dried fully; “A2” appears on the display.

Cupboard dry: suitable for laundry which can be put back in

a cupboard without being ironed; “A3” appears on the display.

Extra dry: suitable for garments which need to be dried

completely, such as sponges and bathrobes; “A4” appears

on the display.

B - Based on a set time period: between 30 and 180 minutes.

If your laundry load to be washed and dried is much

greater than the maximum stated load (see adjacent table),

perform the wash cycle, and when the cycle is complete,

divide the garments into groups and put some of them

back in the drum.

At this point, follow the instructions provided for a “Drying

only” cycle. Repeat this procedure for the remainder of

the load.

N.B: a cooling-down period is always added to the end

of each drying cycle.

Drying only

Use the cycle selector knob to select a drying cycle (15-16)

in accordance with the type of fabric. The desired drying

level or time may also be set using the DRYING button .

Modifying the cycle settings.

• Pressthebuttontoenabletheoption;theindicatorlight

corresponding to the button will switch on.

• Press the button again to disable the option; the

indicator light will switch off.

! If the selected option is not compatible with the

programmed wash cycle, the indicator light will flash and

the option will not be activated.

! If the selected option is not compatible with another

option which has been selected previously, the indicator

light corresponding to the first option selected will flash

and only the second option will be activated; the indicator

light corresponding to the enabled option will remain lit.

! The options may affect the recommended load value

and/or the duration of the cycle.

7. START THE PROGRAMME. Press the START/PAUSE

button. The corresponding indicator light will become

green, remaining lit in a fixed manner, and the door will

be locked (the DOOR LOCKED symbol will be on).

To change a wash cycle while it is in progress, pause

the Washer-dryer using the START/PAUSE button

(the START/PAUSE indicator light will flash slowly in an

orange colour); then select the desired cycle and press

the START/PAUSE button again. To open the door while

a cycle is in progress, press the START/PAUSE button;

if the DOOR LOCKED symbol is switched off the door

may be opened (wait approximately 3 minutes). Press the

START/PAUSE button again to restart the wash cycle from

the point at which it was interrupted.

8. THE END OF THE WASH CYCLE. This will be indicated

by the text “End” on the display; when the DOOR LOCKED

symbol switches off the door may be opened (wait

approximately 3 minutes). Open the door, unload the

laundry and switch off the machine.

! If you wish to cancel a cycle which has already begun, press

and hold the button. The cycle will be stopped and the

machine will switch off.

9

GB

Wash cycles and options

Wash options

- If the selected option is not compatible with the program-

med wash cycle, the indicator light will flash and the option

will not be activated.

- If the selected option is not compatible with another

option which has been selected previously, the indicator

light corresponding to the first option selected will flash

and only the second option will be activated; the indicator

light corresponding to the enabled option will remain lit.

Extra Wash

Enable the

Extra Wash

option for very dirty items, where

compatible. Press this option to let the cycle automatically re-

adjust all wash parameters through a longer lasting cycle. The

option always leaves the temperature unchanged, while the spin

cycle is automatically brought back to maximum levels. The user

can set the spin cycle back to the desired value at any time.

Easy Iron

By selecting this function, the wash and spin cycles will be

modified in order to reduce the formation of creases. At the

end of the cycle the washing machine will perform slow ro-

tations of the drum; the indicator lights for the EASY IRON

and START/PAUSE options will flash (the first one green, the

second orange).

Table of wash cycles

To end the cycle, press the START/PAUSE button or the

EASY IRON button.

Note: If you also want to run the drying cycle, this option is

enabled only if combined with level “A1”(Iron dry).

Extra rinse

By selecting this option, the efficiency of the rinse is increased

and optimal detergent removal is guaranteed. It is particularly

useful for sensitive skin.

Delay start

To set a delayed start for the selected cycle, press the

corresponding button repeatedly until the required delay

period has been reached. When this option is enabled, the

corresponding indicator light will remain lit. To remove the

delayed start setting, press the button until the text “OFF”

appears on the display.

For all Test Institutes:

1) Test wash cycle in compliance with regulations EN 50229: set wash cycle 10 with a temperature of 60°C.

2) Long wash cycle for cottons: set wash cycle 10 with a temperature of 40°C.

The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary according to factors such as water

temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.

Wash

cycles

Description of the wash cycle

Max.

temp.

(°C)

Max. speed

(rpm)

Drying

Detergents

Max.

load

(kg)

Cycle

duration

Main

wash

Fabric

softener

EVERYDAY FAST

The duration of the wash cycles can be checked on the display.

1 Colour Mix 59’

40° 1000

  

7

2 Synthetics 59’

40°

(Max. 60°)

1000

  

4,5

3 Cotton 45’

40° 1200

  

3,5

4 Wash&Dry 90’

30° 1200

  

2

5 Wash&Dry 45’

30° 1200

  

1

6 AirFresh 30’

- -



- - 1,5

Special

7

Wool: for wool, cashmere, etc. 40° 800

  

2

8 Delicate

30° 0

  

1

9 Gym Kit

40° 600

  

3,5

10

Eco Cotton 60° (1): heavily soiled whites and resistant colours. 60° 1200

  

7

10

Eco Cotton 40° (2): lightly soiled whites and delicate colours. 40° 1200

  

7

11

Cotton: extremely soiled whites. 90° 1200

  

7

Partial

12 Rinse

- 1200



-



7

13 Spin

- 1200



- - 7

14 Drain

- 0 - - - 7

15 Cotton dry

- -



- - 5

16 Synthetics dry

- -



- - 4

10

GB

Detergents and laundry

Detergent dispenser drawer

Good washing results also depend on the correct dose of

detergent: adding too much detergent will not necessarily

result in a more efficient wash, and may in fact cause build

up on the inside of your appliance and contribute to envi-

ronmental pollution.

!Use powder detergent for white cotton garments, for pre-

washing, and for washing at temperatures over 60°C.

!Follow the instructions given on the detergent packaging.

! Do not use hand washing detergents because these

create too much foam.

Open the detergent di-

spenser drawer and pour

in the detergent or washing

additive, as follows.

! Do not put the detergent into compartment 1.

! The detergent must be put only in the compartment 2.

compartment 2: Detergent for the wash cycle

(powder or liquid)

Liquid detergent should only be poured in immediately

prior to the start of the wash cycle.

compartment 3: Additives (fabric softeners, etc.)

The fabric softener should not overflow the grid.

Note: If a “tablet detergent” is used, always follow the ma-

nufacturer’s instructions.

Preparing the laundry

•Dividethelaundryaccordingto:

- the type of fabric/the symbol on the label

- the colours: separate coloured garments from whites.

•Emptyallgarmentpocketsandcheckthebuttons.

•Do not exceed the values listed in the “Table of wash

cycles”, which refer to the weight of the laundry when dry.

How much does your laundry weigh?

1 sheet 400-500 g

1 pillow case 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1200 g

1 towel 150-250 g

Fast daily cycles

A complete set of fast programmes to wash the most com-

monly used fabrics - even with a full load - and to remove

the most frequent daily dirt in less than 1 hour.

Colour Mix 59’: to wash mixed and coloured items together.

Synthetics 59’: specific for synthetic items. If the dirt is

difficult to remove, the temperature can be increased up to

60° and powder detergent can be used too.

1

2

3

Cotton 45’: short cycle designed to wash delicate cotton

items.

Special wash cycles

Wash&Dry 90’: The cycle guarantees the washing and

drying performances for a 2 kg load in 90 minutes (level

“A1” Iron dry); for larger loads, the cycle’s duration increa-

ses in order to guarantee the cycle performances.

Wash&Dry 45’ select programme

5

for washing and drying

lightly soiled garments (Cotton and Synthetic) in a short time.

This cycle may be used to wash and dry a laundry load of up

to 1 kg in just 45 minutes (level “A1” Iron dry). To achieve

optimum results, use liquid detergent and pre-treat cuffs,

collars and stains.

AirFresh 30’ (programme

6

) ideal cycle to refresh garments

and remove bad odours, in particular smoke, from cotton and

synthetic items in 30’ (max 1.5kg) without the washing phase.

Wool: all wool garments can be washed using programme

7, even those carrying the “hand-wash only” label. For

best results, use special detergents and do not exceed 2

kg of laundry.

Delicate: use programme 8 to wash very delicate garments.

It is advisable to turn the garments inside out before washing

them. For best results, use liquid detergent on delicate

garments.

To wash Silk garments and Curtains select cycle 8 and then

option “EASY IRON”; the machine will end the cycle while the

laundry is soaking and the “EASY IRON” indicator light will

flash. To drain the water so that the laundry may be removed,

press the START/PAUSE button or the “EASY IRON” button.

When selecting an exclusively time-based drying function, a

drying cycle is performed at the end of the wash cycle that is

particularly delicate, thanks to light handling and appropriate

temperature control of the water jet.

The recommended durations are:

1 kg of synthetic garments --> 150 min

1 kg of synthetic and cotton garments --> 180 min

1 kg of cotton garments --> 180 min

The degree of dryness depends on the load and fabric

composition.

Gym Kit: cycle suitable to wash all sports items together,

including gym towels, while respecting their fibres (follow the

instructions in the garment labels).

Load balancing system

Before every spin cycle, to avoid excessive vibrations and

to distribute the load in a uniform manner, the drum rotates

continuously at a speed which is slightly greater than the

washing rotation speed. If, after several attempts, the load is

not balanced correctly, the machine spins at a reduced spin

speed. If the load is excessively unbalanced, the Washer-

dryer performs the distribution process instead of spinning.

To encourage improved load distribution and balance, we

recommend small and large garments are mixed in the load.

11

GB

Troubleshooting

Your Washer-dryer could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure that

the problem cannot be not solved easily using the following list.

Problem:

The Washer-dryer does not switch on.

The wash cycle does not start.

The Washer-dryer does not take

in water (“H2O” will flash on the

display).

The Washer-dryer continuously

takes in and

drains water.

The Washer-dryer does not drain or

spin.

The Washer-dryer vibrates a lot

during the spin cycle.

The Washer-dryer leaks.

The “option” indicator lights and the

“start/pause” indicator light flash and

an error code appears on the display

(e.g.: F-01, F-..).

There is too much foam.

The washer-dryer does not dry.

Possible causes / Solutions:

•Theapplianceisnotpluggedintothesocketfully,orisnotmakingcontact.

•Thereisnopowerinthehouse.

•TheWasher-dryerdoorisnotclosedproperly.

•TheON/OFFbuttonhasnotbeenpressed.

•TheSTART/PAUSEbuttonhasnotbeenpressed.

•Thewatertaphasnotbeenopened.

• Adelayedstarthasbeenset.

•Thewaterinlethoseisnotconnectedtothetap.

•Thehoseisbent.

•Thewatertaphasnotbeenopened.

•Thereisnowatersupplyinthehouse.

•Thepressureistoolow.

•TheSTART/PAUSEbuttonhasnotbeenpressed.

•Thedrainhoseisnotfittedataheightbetween65and100cmfromthefloor

(see “Installation”).

•Thefreeendofthehoseisunderwater(see “Installation”).

•Thewalldrainagesystemisnotfittedwithabreatherpipe.

If the problem persists even after these checks, turn off the water tap, switch

the appliance off and contact the Assistance Service. If the dwelling is on one of

the upper floors of a building, there may be problems relating to water drainage,

causing the Washer-dryer to fill with water and drain continuously. Special anti-

draining valves are available in shops and help to avoid this inconvenience.

•Thewashcycledoesnotincludedraining:somewashcyclesrequirethedrain

phase to be started manually.

•The“Easyiron”optionhasbeenactivated:Tocompletethewashcycle,press

the START/PAUSE button (see “Wash cycles and options”).

•Thedrainhoseisbent(see “Installation”).

•Thedrainageductisclogged.

•Thedrumwasnotunlockedcorrectlyduringinstallation(see “Installation”).

•TheWasher-dryerisnotlevel(see “Installation”).

•TheWasher-dryeristrappedbetweencabinetsandwalls(see “Installation”).

•Thewaterinlethoseisnotscrewedonproperly(see “Installation”).

•Thedetergentdispenserdrawerisblocked(forcleaninginstructions,see “Care

and maintenance”).

•Thedrainhoseisnotfixedproperly(see “Installation”).

•Switchoffthemachineandunplugit,waitforapproximately1minuteandthen

switch it back on again.

If the problem persists, contact the Technical Assistance Service.

•Thedetergentisnotsuitableformachinewashing(itshoulddisplaythetext

“for Washer-dryers” or “hand and machine wash”, or the like).

•Toomuchdetergentwasused.

• Theapplianceisnotpluggedintothesocket,ornotenoughtomakecontact.

• Therehasbeenapowerfailure.

• The appliance door is not shut properly.

• Adelayedstarthasbeenset.

• DRYINGisintheOFF position.

12

GB

Service

Before calling for Assistance:

• Check whether you can solve the problem alone (see “Troubleshooting”);

•Restarttheprogrammetocheckwhethertheproblemhasbeensolved;

•Ifthisisnotthecase,contactanauthorisedTechnicalAssistanceCentreusingthetelephonenumberprovidedonthe

guarantee certificate.

! Always request the assistance of authorised technicians.

Have the following information to hand:

• thetypeofproblem;

• theappliancemodel(Mod.);

• theserialnumber(S/N).

This information can be found on the data plate applied to the rear of the Washer-dryer, and can also be found on the front of

the appliance by opening the door.

ES

13

Español

Sumario

Instalación, 14-15

Desembalaje y nivelación

Conexiones hidráulicas y eléctricas

Primer ciclo de lavado

Datos técnicos

Mantenimiento y cuidados, 16

Interrumpir el agua y la corriente eléctrica

Limpiar la lavasecadora

Limpiar el contenedor de detergentes

Cuidar la puerta y el cesto

Limpiar la bomba

Controlar el tubo de alimentación de agua

Precauciones y consejos, 17

Seguridad general

Eliminaciones

Descripción de la lavasecadora, 18-19

Panel de control

Pantalla

Cómo efectuar un ciclo de lavado o de

secado, 20

Programas y funciones, 21

Tabla de programas

Funciones de lavado

Detergentes y ropa, 22

Contenedor de detergentes

Preparar la ropa

Ciclos diarios rápidos

Programas particulares

Sistema de equilibrado de la carga

Anomalías y soluciones, 23

Asistencia, 24

ES

EWDE 71280

Manual de instrucciones

LAVASECADORA

! Este símbolo te recuerda que debes leer

este manual de instrucciones.

14

ES

Instalación

! Es importante conservar este manual para

poder consultarlo en cualquier momento. En

caso de venta, de cesión o de traslado, veri-

fique que permanezca junto con la lavadora

para informar al nuevo propietario sobre el

funcionamiento y brindar las correspondientes

advertencias.

! Lea atentamente las instrucciones: ellas

contienen importante información sobre la

instalación, el uso y la seguridad.

Desembalaje y nivelación

Desembalaje

1. Desembale la lavadora.

2. Controle que la lavadora no haya sufri-

do daños durante el transporte. Si estuviera

dañada no la conecte y llame al revendedor.

3. Quite los 4 tornillos

de protección para el

transporte y la aran-

dela de goma con

el correspondiente

distanciador ubicados

en la parte posterior

(ver la figura).

4. Cubra los orificios con los tapones de plá-

stico suministrados con el aparato.

5. Conserve todas las piezas: cuando la la-

vadora deba ser transportada nuevamente,

deberán volver a colocarse.

! Los embalajes no son juguetes para los

niños.

Nivelación

1. Instale la lavadora sobre un piso plano y

rígido, sin apoyarla en las paredes, muebles ni

en ningún otro aparato.

2. Si el piso no está

perfectamente hori-

zontal, compense las

irregularidades desen-

roscando o enroscan-

do las patas delante-

ras (ver la figura); el

ángulo de inclinación

medido sobre la su-

perficie de trabajo, no

debe superar los 2º.

Una cuidadosa nivelación brinda estabilidad

a la máquina y evita vibraciones, ruidos y

desplazamientos durante el funcionamiento.

Cuando se instala sobre moquetas o alfom-

bras, regule los pies para conservar debajo de

la lavadora un espacio suficiente para la venti-

lación.

Conexiones hidráulicas y eléctricas

Conexión del tubo de alimentación de

agua

1. Conectar el tubo

de tubo enroscándolo

a un grifo de agua fría

con la boca roscada

de 3/4 gas (ver la

figura).

Antes de conectarlo,

haga correr el agua

hasta que esté límpi-

da.

2. Conecte el tubo de

alimentación a la lava-

dora enroscándolo en

la toma de agua cor-

respondiente ubicada

en la parte posterior

derecha (arriba) (ver la

figura).

3. Controle que en el tubo no hayan pliegues

ni estrangulaciones.

! La presión de agua del grifo debe estar com-

prendida dentro de los valores contenidos en

la tabla de Datos técnicos (ver la página corre-

spondiente).

! Si la longitud del tubo de alimentación no es

la suficiente, diríjase a un negocio especializa-

do o a un técnico autorizado.

! No utilice nunca tubos ya usados.

! Utilice los suministrados con la máquina.

ES

15

Datos técnicos

Modelo

EWDE 71280

Dimensio-

nes

ancho 59,5 cm.

altura 85 cm.

profundidad 53,5 cm.

Capacidad

de 1 a 7 kg para el lavado

de 1 a 5 kg para el secado.

Conexiones

eléctricas

ver la placa de característi-

cas técnicas aplicada en la

máquina

Conexiones

hídricas

presión máxima 1 MPa (10 bar)

presión mínima 0,05 MPa

(0,5 bar)

capacidad del cesto 58 litros

Velocidad

de centrifu-

gado

máxima 1200 r.p.m.

Programas

de control

según la

reglamentos

EN 50229

Lavado: programa 10;

temperatura 60ºC; efectua-

do con 7 kg. de carga.

Secado: seleccionar el

programa de lavado 10 y el

nivel de secado “A4” para

ambas cargas. El primer

secado se debe efectuar

con la carga manual..

Esta máquina cumple

con lo establecido por las

siguientes Directivas de la

Comunidad:

- EMC 2014/30/EU (Com-

patibilidad Electromagnéti-

ca)

- 2012/19/EU - (WEEE)

- LVD 2014/35/EU (Baja

Tensión)

Conexión del tubo de descarga

Conecte el tubo de de-

scarga, sin plegarlo, a

una tubería de descar-

ga o a una descarga

de pared colocadas

a una altura del piso

entre 65 y 100 cm;

o apóyelo en el borde

de un lavamanos o de

una bañera, uniendo

la guía suministrada

con el aparato, al gri-

fo (ver la figura). El

extremo libre del tubo

de descarga no debe

permanecer sumergi-

do en el agua.

! No se aconseja utilizar tubos de prolongación,

si fuera indispensable hacerlo, la prolongación

debe tener el mismo diámetro del tubo original y

no superar los 150 cm.

Conexión eléctrica

Antes de enchufar el aparato, verifique que:

•latomatengalaconexiónatierrayhayasido

hecha según las normas legales;

•latomaseacapazdesoportarlacargamáxima

de potencia de la máquina indicada en la tabla

de Datos técnicos (ver al costado);

•latensióndealimentaciónestécomprendida

dentro de los valores indicados en la tabla de

Datos técnicos (ver al costado);

•latomaseacompatibleconelenchufedelalava-

dora. Si no es así, sustituya la toma o el enchufe.

! La lavadora no debe ser instalada al aire libre, ni

siquiera si el lugar está reparado, ya que es muy pe-

ligroso dejarla expuesta a la lluvia o a las tormentas.

! Una vez instalada la lavadora, la toma de cor-

riente debe ser fácilmente accesible.

! No utilice prolongaciones ni conexiones múltiples.

! El cable no debe estar plegado ni sufrir com-

presiones.

! El cable de alimentación debe ser sustituido

sólo por técnicos autorizados.

65 - 100 cm

¡Atención! La empresa fabricante declina toda

responsabilidad en caso de que estas normas

no sean respetadas.

Primer ciclo de lavado

Después de la instalación y antes del uso, realice

un ciclo de lavado con detergente y sin ropa,

seleccionando el programa “Auto Limpieza” (ver

“Limpiar la lavasecadora”).

16

ES

Interrumpir el agua y la corriente

eléctrica

•Cierreelgrifodeaguadespuésdecada

lavado. De este modo se limita el desgaste

de la instalación hidráulica de la lavadora y

se elimina el peligro de pérdidas.

•Desenchufelamáquinacuandoladebelim-

piar y durante los trabajos de mantenimiento.

Limpiar la lavasecadora

• La parte externa y las partes de goma se

pueden limpiar con un paño embebido en agua

tibia y jabón. No use solventes ni productos

abrasivos.

•Lalavasecadoraposeeunprogramade“Auto

Limpieza” de su interior que se debe realizar sin

ningún tipo de carga en el cesto.

El detergente (en un 10% de la cantidad acon-

sejada para prendas poco sucias) o algunos

aditivos específicos para la limpieza de la ropa

se podrán utilizar como coadyuvantes en el

programa de lavado. Se aconseja efectuar el

programa de limpieza cada 40 ciclos de lavado.

Para activar el programa pulse simultáneamente

los botones A y B durante 5 segundos (ver la

figura). El programa comenzará automática-

mente y tendrá una duración de 70 minutos

aproximadamente.

Limpiar el contenedor de deter-

gentes

Extraiga el contenedor

levantándolo y tirán-

dolo hacia fuera (ver la

figura).

Lávelo debajo del agua

corriente, esta limpieza

se debe realizar fre-

cuentemente.

Cuidar la puerta y el cesto

•Dejesiempresemicerradalapuertapara

evitar que se formen malos olores.

Limpiar la bomba

La lavadora posee una bomba autolimpiante

que no necesita mantenimiento. Pero puede

suceder que objetos pequeños (monedas, bo-

tones) caigan en la precámara que protege la

bomba, situada en la parte inferior de la misma.

! Verifique que el ciclo de lavado haya termina-

do y desenchufe la máquina.

Para acceder a la precámara:

1. quite el panel que

cubre la parte delan-

tera de la lavadora

con la ayuda de un

destornillador (ver la

figura);

2. desenrosque la

tapa girándola en

sentido antihorario

(ver la figura): es nor-

mal que se vuelque

un poco de agua;

3. limpie con cuidado el interior;

4. vuelva a enroscar la tapa;

5. vuelva a montar el panel verificando, antes de

empujarlo hacia la máquina, que los ganchos

se hayan introducido en las correspondientes

ranuras.

Controlar el tubo de alimentación

de agua

Controle el tubo de alimentación al menos una

vez al año. Si presenta grietas o rajaduras debe

ser sustituido: durante los lavados, las fuertes

presiones podrían provocar roturas imprevistas.

! No utilice nunca tubos ya usados.

Mantenimiento y cuidados

A

B

ES

17

Precauciones y consejos

! La lavasecadora fue proyectada y fabricada en confor-

midad con las normas internacionales de seguridad. Estas

advertencias se suministran por razones de seguridad y

deben ser leídas atentamente.

Seguridad general

•Esteaparatohasidofabricadoparaunusodetipodomé-

stico exclusivamente.

• Esteaparatopuedeserutilizadoporniñosde

8 años o más y por personas con capacida-

des físicas, sensoriales o mentales disminui-

das o con experiencia y conocimientos insufi-

cientes siempre que sean supervisados o

que hayan recibido una adecuada formación

sobre el uso del aparato en forma segura y

conozcan los peligros derivados del mismo.

Los niños no deben jugar con el aparato. El

mantenimiento y la limpieza no deben ser

realizados por niños sin supervisión.

- No secar prendas no lavadas.

- Las prendas sucias con sustancias como

aceite de cocina acetona, alcohol, gasolina,

kerosén, quitamanchas, trementina, cera o

sustancias para quitarlas, deben lavarse con

agua caliente con una cantidad mayor de

detergente antes de secarlas en la secadora.

- Objetos como la goma expandida (látex), las

gorras de ducha, los materiales textiles imper-

meables, los artículos con un lado de goma y

las prendas o cojines que tienen partes de látex

no deben secarse en la secadora.

- Suavizantes o productos similares deben

emplearse de acuerdo con las instrucciones

del fabricante.

- La parte final de un ciclo de la secadora se

realiza sin calor (ciclo de enfriamiento) para

garantizar que los artículos no se dañen.

ATENCIÓN: Nunca detener una secadora

antes que finalice el programa de secado. En

este caso, sacar con rapidez todas las prendas

y colgarlas para enfriarlas con celeridad.

• Notoquelamáquinaconlospiesdesnudosniconlas

manos o los pies mojados o húmedos.

• Nodesenchufelamáquinatirandoelcable,sinotoman-

do el enchufe.

• Notoqueelaguadedescargaporquepuedealcanzar

temperaturas elevadas.

• Nuncafuercelapuerta:podríadañarseelmecanismo

de seguridad que la protege de aperturas accidentales.

• Encasodeavería,noaccedanuncaalosmecanismos

internos para intentar una reparación.

• Controlesiemprequelosniñosnoseacerquenala

máquina cuando está en funcionamiento.

• Sidebesertrasladada,deberánintervenirdosomás

personas, procediendo con el máximo cuidado. La

máquina no debe ser desplazada nunca por una sola

persona ya que es muy pesada.

• Antesdeintroducirlaropacontrolequeelcestoesté

vacío.

•Duranteelsecadolapuertatiendeacalentarse.

•Nosequeropalavadaconsolventes 

inflamables (por ej. tricloroetileno).

•Nosequegomaespumaoelastómeros 

análogos.

•Verifiqueque,durantelasfasesdesecado,elgrifode

agua esté abierto.

•Losniñosdeedadinferiora3añosdeben

mantenerse alejados de la secadora en au

sencia de vigilancia constante.

•Vaciarlosbolsillosdetodoslosobjetos,

como encende dores o fósforos.

Eliminaciones

•Eliminacióndelmaterialdeembalaje:respetelasnormas

locales, de ese modo, los embalajes podrán volver a ser

utilizados.

•EnbasealaNormaeuropea2012/19/EU-WEEEde

Residuos de aparatos Eléctricos y Electrónicos, los

electrodomésticos viejos no pueden ser arrojados en

los contenedores municipales habituales; tienen que ser

recogidos selectivamente para optimizar la recuperación

y reciclado de los componentes y materiales que los

constituyen, y reducir el impacto en la salud humana y el

medioambiente. El símbolo del cubo de basura tachado

se marca sobre todos los productos para recordar al

consumidor la obligación de separarlos para la recogida

selectiva.

El consumidor debe contactar con la autoridad local o

con el vendedor para informarse en relación a la correc-

ta eleminación de su electrodoméstico viejo.

18

ES

Contenedor de detergentes: para cargar detergentes

y aditivos (ver “Detergentes y ropa”).

Botón ON/OFF : presione brevemente el botón para

encender o apagar la máquina. El piloto START/PAUSE

que centellea lentamente de color verde indica que la

máquina está encendida. Para apagar la lavasecadora

durante el lavado, es necesario mantener presionado el

botón durante más tiempo, aproximadamente 2 seg.; si se

presiona en forma más breve o accidental, la máquina no

se apagará. Si la máquina se apaga durante un lavado en

curso, dicho lavado se anulará.

Mando de PROGRAMAS: para elegir los programas.

Durante el funcionamiento del programa el mando no se

mueve.

Botones con pilotos de FUNCIÓN: para seleccionar las

funciones disponibles. El piloto correspondiente a la fun-

ción seleccionada permanecerá encendido.

Botón CENTRIFUGADO : presiónelo para disminuir o

excluir totalmente el centrifugado - el valor se indica en la

pantalla.

Botón TEMPERATURA : presiónelo para disminuir o

excluir la temperatura; el valor se indica en la pantalla.

Botón SECADO : presionar para reducir o excluir el

secado; el nivel o el tiempo de secado seleccionado se

indica en el visor (ver “Cómo efectuar un ciclo de lavado o

de secado”).

Botón con piloto START/PAUSE : cuando el piloto

verde centellea lentamente, presione el botón para que

comience el lavado. Una vez que el ciclo ha comenzado,

el piloto se mantiene fijo. Para poner en pausa el lavado,

presione nuevamente el botón; el piloto centelleará con

un color anaranjado. Si el símbolo no está iluminado, se

podrá abrir la puerta (espere 3 minutos aproximadamente).

Para que el lavado se reanude a partir del momento en el

cual fue interrumpido, presione nuevamente el botón.

Modalidad de stand by

Esta lavasecadora está en conformidad con las nuevas

normativas vinculadas al ahorro energético. Está dotada

de un sistema de auto-apagado (stand by) que, en caso

de no funcionamiento, se activa pasados aproximadamen-

te 30 minutos. Presionar brevemente el botón ON-OFF y

esperar que la máquina se active.

Consumo en off-mode: 0,5 W

Consumo en Left-on: 8 W

Descripción de la lavasecadora

Panel de control

Botón con

piloto START/

PAUSE

Botón

TEMPERATURA

Botón

CENTRIFUGADO

Mando de

PROGRAMAS

Botones con pilotos

FUNCIÓN

Contenedor de

detergentes

Botón de ON/OFF

PANTALLA

Botón

SECADO

ES

19

Pantalla

La pantalla es útil para programar la máquina y brinda múltiple información.

En la sección A se visualiza la duración de los distintos programas a disposición y, para los que han comenzado, el tiempo

que falta para su finalización; si se hubiera seleccionado un COMIENZO RETRASADO, se visualiza el tiempo que falta para

que comience el programa seleccionado. Además, presionando el botón correspondiente, se visualizan los valores máximos

de temperatura, de velocidad de centrifugado y del nivel o del tiempo de secado que la máquina puede alcanzar en base al

programa seleccionado.

En la sección B se visualizan las fases previstas para el ciclo seleccionado y, una vez comenzado el programa, la fase de

lavado y eventualmente de secado en curso:

Lavado

Aclarado

Centrifugado/Descarga

Secado

En la sección C se encuentran, de arriba hacia abajo, los íconos correspondientes a la “temperatura” , al “Secado” y al

“centrifugado” :

El símbolo iluminado indica que en la pantalla se visualiza el valor seleccionado de “temperatura”.

El símbolo se ilumina durante la regulación del secado.

El símbolo iluminado indica que en la pantalla se visualiza el valor seleccionado de “centrifugado”.

Símbolo Puerta bloqueada

El símbolo encendido indica que la puerta está bloqueada. Para evitar daños, se debe esperar que el símbolo se apague,

antes de abrir la puerta (espere 3 minutos aproximadamente).

Para abrir la puerta mientras un ciclo está en curso, presione el botón START/PAUSE; si el símbolo PUERTA BLOQUEADA

está apagado, será posible abrir la puerta (espere 3 minutos aproximadamente).

B

CA

20

ES

Cómo efectuar un ciclo de lavado

o de secado

1. ENCENDER LA MÁQUINA. Presione el botón ; el

piloto START/PAUSE centelleará lentamente de color

verde.

2. CARGAR LA ROPA. Abra la puerta. Cargue la ropa,

cuidando no superar la cantidad de carga indicada en la

tabla de programas de la página siguiente.

3. DOSIFICAR EL DETERGENTE. Extraiga el contenedor

y vierta el detergente en las cubetas correspondientes

como se explica en “Detergentes y ropa”.

4. CERRAR LA PUERTA.

5. ELEGIR EL PROGRAMA. Seleccione el programa

deseado con el mando de PROGRAMAS; a dicho

programa se le asociará una temperatura y una velocidad

de centrifugado que se pueden modificar. En la pantalla

aparecerá la duración del ciclo.

6. PERSONALIZAR EL CICLO DE LAVADO. Utilice los

botones correspondientes:

Modificar la temperatura y/o el centrifugado.

La máquina muestra automáticamente la temperatura y

la centrífuga máximas previstas para el programa fijado

o las últimas seleccionadas si son compatibles con el

programa elegido. Presionando el botón se disminuye

progresivamente la temperatura hasta llegar al lavado

en frío “OFF”. Presionando el botón se disminuye

progresivamente el centrifugado hasta su exclusión “OFF”.

Si se presionan una vez más los botones, se volverá a los

valores máximos previstos.

! Excepción: cuando se selecciona el programa 2, la

temperatura se puede aumentar hasta 60°.

Programar el secado. Con la primera presión

del botón la máquina selecciona automáticamente

el nivel de secado máximo compatible con el programa

seleccionado. Las siguientes presiones disminuyen el nivel

y el tiempo de secado hasta llegar a la exclusión “OFF”.

Si se presionan una vez más los botones, se volverá a los

valores máximos previstos.

Es posible programar el secado:

A - En función del nivel de secado deseado:

Planchar (A1): especial para prendas que después de-

ben plancharse. El nivel de humedad residual atenúa las

arrugas y facilita su eliminación.

Colgar (A2): ideal para aquellas prendas que no requieren

el secado completo.

Doblar (A3): se adapta para la ropa que se coloca en el

armario sin necesidad de planchar.

Extra (A4): especial para las prendas que necesi-

tan un secado completo como toallas o albornoces.

B - En base al tiempo: de 30 a 180 minutos.

Si excepcionalmente la carga de ropa para lavar y secar

es superior al máximo previsto (ver la Tabla de programas),

realice el lavado, y una vez finalizado el programa, divida

la carga y coloque una parte en el cesto. A partir de ese

momento, siga las instrucciones para efectuar “Sólo el

secado”.

Repita las mismas operaciones para la carga restante.

Al finalizar el secado continúa siempre un período de

enfriamiento.

Sólo el secado

Seleccionar con el mando de programas el secado

adecuado (15-16) al tipo de tejido. Se puede programar

también el nivel o el tiempo de secado deseado utilizando

el botón SECADO .

Modificar las características del ciclo.

• Presione el botón para activar la función; el piloto

correspondiente al botón se encenderá.

• Presione nuevamente el botón para desactivar la

función; el piloto se apagará.

! Si la función seleccionada no es compatible con el

programa elegido, el piloto centelleará y la función no se

activará.

! Si la función elegida no es compatible con otra

seleccionada precedentemente, el piloto correspondiente

a la primera función seleccionada centelleará y se activará

sólo la segunda, el piloto de la función activada se

iluminará.

! Las funciones pueden variar la carga recomendada y/o

la duración del ciclo.

7. PONER EN MARCHA EL PROGRAMA. Presione

el botón START/PAUSE. El piloto correspondiente se

iluminará de color verde fijo y la puerta se bloqueará

(símbolo PUERTA BLOQUEADA encendido). Para

cambiar un programa mientras un ciclo está en curso,

ponga la lavasecadora en pausa presionando el botón

START/PAUSE (el piloto START/PAUSE centelleará

lentamente de color anaranjado); luego seleccione el ciclo

deseado y presione nuevamente el botón START/PAUSE.

Para abrir la puerta mientras un ciclo está en curso,

presione el botón START/PAUSE; si el símbolo PUERTA

BLOQUEADA está apagado, será posible abrir la

puerta (espere 3 minutos aproximadamente). Presione

nuevamente el botón START/PAUSE para reanudar

el programa a partir del momento en el que se había

interrumpido.

8. FIN DEL PROGRAMA. En la pantalla aparecerá el

mensaje “END”, cuando el símbolo PUERTA BLOQUEADA

se apague, será posible abrir la puerta (espere 3 minutos

aproximadamente). Abra la puerta, descargue la ropa y

apague la máquina.

! Si desea anular un ciclo que ya ha comenzado, presione

más tiempo el botón . El ciclo se interrumpirá y la máquina

se apagará.

Stránka sa načítava ...

Indesit EWDE 71280 W EU Užívateľská príručka

Indesit EWDE 71280 W EU Užívateľská príručka

V iných jazykoch

Súvisiace články

Ďalšie dokumenty