Indesit PWSE 6108 W (EU) Užívateľská príručka

Značka: Indesit

Model: PWSE 6108 W (EU)

Kategória: Práčky

Typ: Užívateľská príručka

English, 1

WASHING MACHINE

Contents

Installation, 2-3

Unpacking and levelling

Connecting the electricity and water supplies

The first wash cycle

Technical data

Description of the washing machine, 4-5

Control panel

Display

Running a wash cycle, 6

Wash cycles and options, 7

Table of programmes and wash cycles

Wash options

Detergents and laundry, 8

Detergent dispenser drawer

Preparing the laundry

Special wash cycles

Precautions and advice, 9

General safety

Disposal

Opening the porthole door manually

Care and maintenance, 10

Cutting off the water and electricity supplies

Cleaning the washing machine

Cleaning the detergent dispenser drawer

Cleaning the pump

Checking the water inlet hose

Troubleshooting, 11

Service, 12

PWSE 6108 W

Instructions for use

Èesky,25

Slovensky,13

Installation

 This instruction manual should be kept in a safe place

for future reference. If the washing machine is sold,

transferred or moved, make sure that the instruction

manual remains with the machine so that the new

owner is able to familiarise himself/herself with its

operation and features.

 Read these instructions carefully: they contain vital

information relating to the safe installation and operation

of the appliance.

Unpacking and levelling

Unpacking

1. Remove the washing machine from its packaging.

2. Make sure that the washing machine has not been

damaged during the transportation process. If it has

been damaged, contact the retailer and do not proceed

any further with the installation process.

3. Remove the 4

protective screws (used

during transportation) and

the rubber washer with

the corresponding spacer,

located on the rear part of

the appliance (see figure).

4. Close off the holes using the plastic plugs provided.

5. Keep all the parts in a safe place: you will need them

again if the washing machine needs to be moved to

another location.

 Packaging materials should not be used as toys for

children.

Levelling

1. Install the washing machine on a flat sturdy floor,

without resting it up against walls, furniture cabinets or

anything else.

2. If the floor is not

perfectly level,

compensate for any

unevenness by tightening

or loosening the adjustable

front feet (see figure); the

angle of inclination,

measured in relation to the

worktop, must not exceed

2°.

Levelling the machine correctly will provide it with

stability, help to avoid vibrations and excessive noise and

prevent it from shifting while it is operating. If it is placed

on carpet or a rug, adjust the feet in such a way as to

allow a sufficient ventilation space underneath the

washing machine.

Connecting the electricity and water

supplies

Connecting the water inlet hose

1. Connect the inlet hose

by screwing it to a cold

water tab using a 3/4 gas

threaded connection (see

figure).

Before performing the

connection, allow the

water to run freely until it is

perfectly clear.

2. Connect the inlet hose

to the washing machine

by screwing it onto the

corresponding water inlet

of the appliance, which is

situated on the top right-

hand side of the rear part

of the appliance (see

figure).

3. Make sure that the hose is not folded over or bent.

 The water pressure at the tap must fall within the

range of values indicated in the Technical data table (see

next page).

 If the inlet hose is not long enough, contact a

specialised shop or an authorised technician.

 Never use second-hand hoses.

 Use the ones supplied with the machine.

Connecting the drain hose

Connect the drain hose,

without bending it, to a

drain duct or a wall drain

situated between 65 and

100 cm from the floor;

alternatively, place it

over the edge of a

basin, sink or tub,

fastening the duct

supplied to the tap (see

figure). The free end of

the hose should not be

underwater.

 We advise against the use of hose extensions; if it is

absolutely necessary, the extension must have the

same diameter as the original hose and must not

exceed 150 cm in length.

Electrical connections

Before plugging the appliance into the electricity

socket, make sure that:

 the socket is earthed and complies with all

applicable laws;

 the socket is able to withstand the maximum

power load of the appliance as indicated in the

Technical data table (see opposite);

 the power supply voltage falls within the values

indicated in the Technical data table (see opposite);

 the socket is compatible with the plug of the

washing machine. If this is not the case, replace the

socket or the plug.

 The washing machine must not be installed

outdoors, even in covered areas. It is extremely

dangerous to leave the appliance exposed to rain,

storms and other weather conditions.

 When the washing machine has been installed, the

electricity socket must remain within easy reach.

 Do not use extension cords or multiple sockets.

65 - 100 cm

 The cable should not be bent or compressed.

 The power supply cable must only be replaced by

authorised technicians.

Warning! The company shall not be held responsible

in the event that these standards are not observed.

The first wash cycle

Once the appliance has been installed, and before you

use it for the first time, run a wash cycle with

detergent and no laundry, using wash cycle number 2.

Technical data

Model

PWSE 6108 W

Dimensions

width 59.5 cm

height 85 cm

depth 44,5 cm

Capacity

between 1 and 6 kg

Electrical

connections

please refer to the technical data

plate applied to the machine

Water connections

maximum pressure 1 MPa (10 bar

)

minimum pressure 0.05 MPa

(0.5 bar)

drum capacity 40 litres

Spin speed

up to 1000 rpm

Test wash cycles

in compliance with

regulation

EN 60456

wash cycle 2; temperature 60°C;

performed with a 6 kg load.

This appliance conforms to the

following European Community

directives:

- 89/336/EEC dated 03.05.89

(Electromagnetic Compatibility)

and subsequent amendments

- 2006/95/EC – 2006/95/EC (Low

Voltage)

Description of the washing

machine

Control panel

TEMPERATURE

button

WASH

CYCLE

SELECTOR

KNOB

Detergent dispenser drawer

ON/OFF

button

SPIN

button

START/PAUSE

button and indicator

light

DISPLAY

DELAYED

START

button

OPTION

buttons and

indicator lights

DOOR

LOCKED

indicator light

Detergent dispenser drawer: used to dispense

detergents and washing additives ( see Detergents

and laundry).

ON/OFF

button: press this briefly to switch the

machine on or off. The START/PAUSE indicator light

which flashes slowly in a blue colour shows that the

machine is switched on. To switch off the washing

machine during the wash cycle, press and hold the

button for approximately 3 seconds; if the button is

pressed briefly or accidentally the machine will not

switch off.

If the machine is switched off during a wash cycle,

this wash cycle will be cancelled.

WASH CYCLE SELECTOR KNOB: used to set the

desired wash cycle (see Table of programmes and

wash cycles).

OPTION buttons and indicator lights: press to

select the available options. The indicator light

corresponding to the selected option will remain lit.

SPIN

button: press to reduce or completely

exclude the spin cycle; the value appears on the

display.

TEMPERATURE

button: press to reduce or

completely exclude the temperature; the value

appears on the display.

DELAYED START

button: press to set a delayed

start for the selected wash cycle; the delay period

appears on the display.

START/PAUSE

button and indicator light: when

the blue indicator light flashes slowly, press the button

to start a wash cycle. Once the cycle has begun the

indicator light will remain lit in a fixed manner. To

pause the wash cycle, press the button again; the

indicator light will flash in an amber colour. If the

symbol is not illuminated, the door may be opened. To

start the wash cycle from the point at which it was

interrupted, press the button again.

DOOR LOCKED

indicator light:

The lit symbol indicates that the door is locked. To

prevent any damage, wait until the symbol turns off

before opening the door.

To open the door while a cycle is in progress, press

the START/PAUSE button; if the DOOR LOCKED

symbol is switched off the door may be opened.

Standby mode

This washing machine, in compliance with new

energy saving regulations, is fitted with an automatic

standby system which is enabled after a few minutes

if no activity is detected. Press the ON-OFF button

briefly and wait for the machine to start up again.

Display

The display is useful when programming the machine and provides a great deal of information.

The duration of the available wash cycles and the remaining time of a running cycle appear in section A; if the

DELAYED START option has been set, the countdown to the start of the selected wash cycle will appear.

Pressing the corresponding button allows you to view the maximum spin speed and temperature values attained

by the machine during the set wash cycle, or the values selected most recently, if these are compatible with the

set wash cycle.

The hour-glass flashes while the machine is processing data, depending on the wash cycle and Smart level

selected. After a maximum of 10 minutes, the hour-glass icon remains lit in a fixed manner and the final amount

of time remaining is displayed. The hour-glass icon will then switch off approximately 1 minute after the final

amount of time remaining has appeared.

The wash cycle phases corresponding to the selected wash cycle and the wash cycle phase of the running

wash cycle appear in section B:

Main wash

Rinse

Spin

Drain

The icons corresponding to temperature, spin and delayed start (working from the left) are displayed in

section C.

The temperature bars

indicate the maximum temperature level which may be selected for the set cycle.

The spin bars

indicate the maximum spin level which may be selected for the set cycle.

The delay symbol

, when lit, indicates that the set delayed start value has appeared on the display.

Running a wash cycle

1. SWITCH THE MACHINE ON. Press the

button; the START/PAUSE indicator light will flash

slowly in a blue colour.

2. LOAD THE LAUNDRY. Open the porthole door.

Load the laundry, making sure you do not exceed

the maximum load value indicated in the table of

programmes and wash cycles on the following

page.

3. MEASURE OUT THE DETERGENT. Pull out the

detergent dispenser drawer and pour the detergent

into the relevant compartments as described in

Detergents and laundry.

4. CLOSE THE DOOR.

5. SELECT THE WASH CYCLE. Use the WASH

CYCLE SELECTOR knob to select the desired

wash cycle. A temperature and spin speed is set

for each wash cycle; these values may be

adjusted. The duration of the cycle will appear on

the display.

6. CUSTOMISE THE WASH CYCLE. Use the

relevant buttons:

Modify the temperature and/or spin

speed. The machine automatically displays the

maximum temperature and spin speed values set

for the selected cycle, or the most recently-used

settings if they are compatible with the selected

cycle. The temperature can be decreased by

pressing the

button, until the cold wash OFF

setting is reached. The spin speed may be

progressively reduced by pressing the

button,

until it is completely excluded (the OFF setting). If

these buttons are pressed again, the maximum

values are restored.

Setting a delayed start.

To set a delayed start for the selected cycle, press

the corresponding button repeatedly until the

required delay period has been reached. When this

option has been activated, the

symbol lights up

on the display. To remove the delayed start setting,

press the button until the text OFF appears on

the display.

Modify the cycle settings.

 Press the button to enable the option; the

indicator light corresponding to the button will

switch on.

 Press the button again to disable the option; the

indicator light will switch off.

 If the selected option is not compatible with the

set wash cycle, the indicator light will flash and the

option will not be activated.

 If the selected option is not compatible with a

previously selected one, the indicator light

corresponding to the first function selected will flash

and only the second option will be activated; the

indicator light for the option which has been

activated will be illuminated.

Note: if the SMART option has been selected,

none of the incompatible options may be activated.

 The options may affect the recommended load

value and/or the duration of the cycle.

7. START THE WASH CYCLE. Press the START/

PAUSE button. The corresponding indicator light will

turn blue, remaining lit in a fixed manner, and the

door will be locked (the DOOR LOCKED

symbol

will be lit). To change a wash cycle while it is in

progress, pause the washing machine using the

START/PAUSE button (the START/PAUSE indicator

light will flash slowly in an amber colour); then

select the desired cycle and press the START/

PAUSE button again.

To open the door while a cycle is in progress, press

the START/PAUSE button; if the DOOR LOCKED

symbol is switched off the door may be opened.

Press the START/PAUSE button again to restart the

wash cycle from the point at which it was

interrupted.

8. THE END OF THE WASH CYCLE. This will be

indicated by the text END on the display; when

the DOOR LOCKED

symbol switches off the door

may be opened. Open the door, unload the laundry

and switch off the machine.

 If you wish to cancel a cycle which has already

begun, press and hold the

button. The cycle will be

stopped and the machine will switch off.

Load balancing system

Before every spin cycle, to avoid excessive vibrations

before every spin and to distribute the load in a

uniform manner, the drum rotates continuously at a

speed which is slightly greater than the washing

rotation speed. If, after several attempts, the load is

not balanced correctly, the machine spins at a

reduced spin speed. If the load is excessively

unbalanced, the washing machine performs the

distribution process instead of spinning. To encourage

improved load distribution and balance, we

recommend small and large garments are mixed in

the load.

Wash cycles and

options

Wash options

The option optimises washing to suit the quantity

of laundry loaded into the machine, thereby reducing the

overall wash cycle duration while minimising water and

energy consumption. Press the

button to select

the type of wash cycle desired:

Intensive: vigorous wash cycle for garments with a heavy

soil level.

4 You: standard wash cycle for garments with a normal soil level.

Fast: quick wash cycle for garments with a light soil level.

 This may only be used in conjunction with wash cycles 1, 2,

3, 4, 5, 6 (all three levels) and 7, 8, 9 (4 You and Fast levels).

Extra Rinse

By selecting this option, the efficiency of the rinse is

increased and optimal detergent removal is guaranteed. It

is particularly useful for sensitive skin.

 It cannot be used in conjunction with wash cycles 9, , .

Easy iron

By selecting this function, the wash and spin cycles will be

modified in order to reduce the formation of creases. At the

end of the cycle the washing machine will perform slow

rotations of the drum, while the EASY IRON and START/

PAUSE indicator lights will flash (blue and orange respectively).

To end the cycle, press the START/PAUSE button or the

EASY IRON button. For wash cycles number 11-13, the

machine will end the cycle while the laundry is soaking; the

EASY IRON and START/PAUSE indicator lights will flash. To

drain the water so that the laundry may be removed, press

the START/PAUSE button or the EASY IRON button.

 It cannot be used in conjunction with wash cycles 9, 10,

12,

, .

Stain removal

This function is particularly

useful for the removal of

stubborn stains. Insert extra

compartment 4 (supplied

with the appliance) into

compartment 1. When

pouring in the bleach, be

careful not to exceed the

max level marked on the

central pivot (see figure). To

bleach laundry with no other

washing action, pour the bleach into extra compartment 4,

select the Rinse cycle

and activate the Stain

removal option

. To bleach during a wash cycle, pour in

the detergent and any fabric softener you wish to use,

select the desired wash cycle and enable the Stain

removal

option. The use of extra compartment 4

excludes the pre-wash function.

 It cannot be used in conjunction with wash cycles 1, 7,

9, 10, 11, 12, 13,

, .

For all Test Institutes:

1) Test wash cycle in compliance with regulation EN 60456: select wash cycle 2 with a temperature of 60°C.

2) Long wash cycle for cottons: select wash cycle 2 with a temperature of 40.

3) Short wash cycle for cottons: select wash cycle 4 with a temperature of 40.

Table of programmes and wash cycles

Detergents

Description of the wash cycle

Max.

temp.

(°C)

Max.

speed

(rpm)

Pre-wash

Main

wash

Bleach

Fabric softener

Max.

load

(kg)

Cycle

duration

Smart cycles

Cottons with Pre-wash

: extrem ely

soiled whites.

90°

1000

•

White Cottons

: extremely soiled

whites.

90°

1000 -

•

White Cottons (1)

: heavily soiled

whites and resistant colours.

60°

1000 -

•

White Cottons (2)

: heavily soiled

whites and delicate colours.

40°

1000 -

•

Cottons

: heavily soiled whites and

resistant colours.

60°

1000 -

•

Coloured Cottons(3)

: lightly soiled

whites and delicate colours.

40°

1000 -

•

Synthetics

: heavily soiled resistant

colours.

60°

800 -

•

2,5

Synthetics

: lightly soiled resistant

colours.

40°

800 -

•

2,5

7 Jeans

40°

800 -

•

8 Shirts

40°

600 -

•

Mix-Cool 30’

: to refresh lightly soiled

garments quickly (not suitable for

wool, silk and clothes which require

washing by hand).

Cold

water

800 -

•

Special cycles

10 Wool

: for wool, cashm ere, etc.

40°

600 -

•

1,5

Silk/Curtains

: for garm ents in silk

and viscose, lingerie.

30°

0 -

•

12 Sport Shoes

30° 600 -

•

Max..2

paires

13 Outwear

30°

400 -

•

- - 2

Partial cycles

Rinse

- 1000 - -

•

Spin

- 1000 - - - - 6

Drain

- 0 - - - - 6

Wash

cycles

The duration of the wash cycles can be checked on the display.

Detergents and laundry

Detergent dispenser drawer

Successful washing results also depend on the correct

dose of detergent: adding too much detergent will not

necessarily result in a more efficient wash, and may in

fact cause build up on the inside of your appliance and

contribute to environmental pollution.

 Do not use hand washing detergents; they create too

much foam.

Open the detergent

dispenser drawer and pour

in the detergent or washing

additive, as follows.

Compartment 1: Pre-wash detergent (powder)

Before pouring in the detergent, make sure that extra

compartment 4 has been removed.

Compartment 2: Washing detergent (powder or

liquid)

Liquid detergent should only be poured in immediately

prior to the start of the wash cycle.

Compartment 3: Additives (fabric softeners,

etc.)

The fabric softener should not overflow the grid.

extra compartment 4: Bleach

Preparing the laundry

 Divide the laundry according to:

- the type of fabric/the symbol on the label

- the colours: separate coloured garments from

whites.

 Empty all garment pockets and check the buttons.

 Do not exceed the listed values, which refer to the

weight of the laundry when dry:

Durable fabrics: max. 6 kg

Synthetic fabrics: max. 2.5 kg

Delicate fabrics: max. 2 kg

Wool: max. 1,5 kg

Silk: max. 1 kg

How much does your laundry weigh?

1 sheet 400-500 g

1 pillow case 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1,200 g

1 towel 150-250 g

Special wash cycles

Jeans: turn the garments inside out before washing

and use liquid detergent. Use wash cycle 7.

Shirts: use special wash cycle 8 to wash shirts in

various fabrics and colours.

It guarantees maximum care is taken of the garments

and minimises the formation of creases.

Mix-Cool 30:

this wash cycle was designed to wash

lightly soiled garments quickly: it lasts just 30 minutes

and therefore saves both energy and time. By selecting

wash cycle 9, it is possible to wash different fabrics

(except for wool and silk items) using a cold cycle, up to

a maximum load of 3 kg.

Wool: wash cycle 10 can be used to wash all woollen

garments in the machine, even those carrying the hand

wash only

label. To achieve the best results, use a

special detergent and do not exceed the maximum load

of 1,5 kg.

Silk: use special wash cycle 11 to wash all silk

garments. We recommend the use of special detergent

which has been designed to wash delicate clothes.

Curtains: we recommend you fold the curtains and

place them in a pillow case or mesh bag. Use wash

cycle 11.

Sport Shoes (

wash cycle

12): is for washing sports

shoes; for best results, do not wash more than 2 pairs

simultaneously.

Outwear(

wash cycle

13): is studied for washing water-

repellent fabrics and winter jackets (e.g. Gore-Tex,

polyester, nylon); for best results, use a liquid detergent

and dosage suitable for a half-load; pre-treat necks,

cuffs and stains if necessary; do not use softeners or

detergents containing softeners. Stuffed duvets cannot

be washed with this programme.

Precautions and tips

Opening the porthole door manually

In the event that it is not possible to open the porthole

door due to a powercut, and if you wish to remove

the laundry, proceed as follows:

1. Remove the plug from

the electrical socket..

2. Make sure the water

level inside the machine is

lower than the door

opening; if it is not, remove

excess water using the

drain hose, collecting it in a

bucket as indicated in the

figure.

3. Remove the cover panel on the lower front part of

the washing machine (see overleaf).

4. Pull outwards using the tab as indicated in the

figure, until the plastic tie-rod is freed from its stop

position; pull downwards and open the door at the

same time.

5. Reposition the panel, making sure the hooks are

securely in place before you push it onto the

appliance.

 This washing machine was designed and constructed

in accordance with international safety regulations. The

following information is provided for safety reasons and

must therefore be read carefully.

General safety

 This appliance was designed for domestic use only.

 The washing machine must only be used by adults, in

accordance with the instructions provided in this manual.

 Do not touch the machine when barefoot or with wet

or damp hands or feet.

 Do not pull on the power supply cable when

unplugging the appliance from the electricity socket.

Hold the plug and pull.

 Do not open the detergent dispenser drawer while the

machine is in operation.

 Do not touch the drained water as it may reach

extremely high temperatures.

 Never force the porthole door. This could damage the

safety lock mechanism designed to prevent accidental

opening.

 If the appliance breaks down, do not under any

circumstances access the internal mechanisms in an

attempt to repair it yourself.

 Always keep children well away from the appliance

while it is operating.

 The door can become quite hot during the wash cycle.

 If the appliance has to be moved, work in a group of

two or three people and handle it with the utmost

care. Never try to do this alone, because the

appliance is very heavy.

 Before loading laundry into the washing machine,

make sure the drum is empty.

Disposal

 Disposing of the packaging materials:

observe local regulations so that the packaging may

be re-used.

 The European Directive 2002/96/EC relating to Waste

Electrical and Electronic Equipment (WEEE) states

that household appliances should not be disposed of

using the normal solid urban waste cycle. Exhausted

appliances should be collected separately in order to

optimise the cost of re-using and recycling the

materials inside the machine, while preventing

potential damage to the atmosphere and to public

health. The crossed-out dustbin is marked on all

products to remind the owner of their obligations

regarding separated waste collection.

For more information relating to the correct disposal of

household appliances, owners should contact their

local authorities or appliance dealer.

Care and maintenance

Cutting off the water and electricity

supplies

 Turn off the water tap after every wash cycle. This

will limit wear on the hydraulic system inside the

washing machine and help to prevent leaks.

 Unplug the washing machine when cleaning it and

during all maintenance work.

Cleaning the washing machine

The outer parts and rubber components of the

appliance can be cleaned using a soft cloth soaked in

lukewarm soapy water. Do not use solvents or

abrasives.

Cleaning the detergent dispenser

drawer

To remove the drawer,

press lever (1) and pull the

drawer outwards (2) (see

figure).

Wash it under running

water; this procedure

should be repeated

frequently.

Cleaning the pump

The washing machine is fitted with a self-cleaning

pump which does not require any maintenance.

Sometimes, small items (such as coins or buttons)

may fall into the protective pre-chamber at the base

of the pump.

 Make sure the wash cycle has finished and unplug

the appliance.

To access the pre-chamber:

1. Take off the cover

panel on the front of the

machine by first pressing

it in the centre and then

pushing downwards on

both sides until you can

remove it (see figures).

2. Unscrew the lid by

rotating it anti-clockwise

(see figure): a little water

may trickle out. This is

perfectly normal.

3. Clean the inside thoroughly.

4. Screw the lid back on.

5. Reposition the panel, making sure the hooks are

securely in place before you push it onto the

appliance.

Checking the water inlet hose

Check the inlet hose at least once a year. If there are

any cracks, it should be replaced immediately: during

the wash cycles, water pressure is very strong and a

cracked hose could easily split open.

 Never use second-hand hoses.

Troubleshooting

Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Service (see 

Service), make sure that the problem cannot be not solved easily using the following list.

Problem:

The washing machine does not

switch on.

The wash cycle does not start.

The washing machine does not

fill with water (the text H2O

flashes on the display).

The washing machine

continuously takes in and

drains water.

The washing machine does not

drain or spin.

The washing machine vibrates

a lot during the spin cycle.

The washing machine leaks.

The option and START/PAUSE

indicator lights flash rapidly and

an error code appears on the

display (e.g.: F-01, F-..).

There is too much foam.

Possible causes / Solutions:

 The appliance is not plugged into the socket fully, or not enough to make

contact.

 There is no power in the house.

 The washing machine door is not closed properly.

 The ON/OFF button has not been pressed.

 The START/PAUSE button has not been pressed.

 The water tap has not been opened.

 A delayed start has been set.

 The water inlet hose is not connected to the tap.

 The hose is bent.

 The water tap has not been opened.

 There is no water supply in the house.

 The pressure is too low.

 The START/PAUSE button has not been pressed.

 The drain hose is not fitted at a height between 65 and 100 cm from the floor

(see Installation).

 The free end of the hose is under water (see Installation).

 The wall drainage system is not fitted with a breather pipe.

If the problem persists even after these checks, turn off the water tap, switch

the appliance off and contact the Technical Assistance Service. If the dwelling is

on one of the upper floors of a building, there may be problems relating to water

drainage, causing the washing machine to fill with water and drain continuously.

Special anti-draining valves are available in shops and help to prevent this

inconvenience.

 The wash cycle does not include draining: some cycles require the draining

process to be enabled manually.

 The EASY IRON option is enabled: To complete the wash cycle, press the

START/PAUSE button (see Wash cycles and options).

 The drain hose is bent (see Installation).

 The drainage duct is clogged.

 The drum was not unlocked correctly during installation (see Installation).

 The washing machine is not level (see Installation).

 The washing machine is trapped between cabinets and walls (see

Installation).

 The water inlet hose is not screwed on properly (see Installation).

 The detergent dispenser drawer is blocked (for cleaning instructions, see Care

and maintenance).

 The drain hose is not fixed properly (see Installation).

 Switch off the machine and unplug it, wait for approximately 1 minute and

then switch it back on again.

If the problem persists, contact the Technical Assistance Service.

 The detergent is not suitable for machine washing (it should display the text

for washing machines or hand and machine wash, or the like).

 Too much detergent was used.

Service

Before contacting the Technical Assistance Service:

 Check whether you can solve the problem alone (see Troubleshooting).

 Restart the wash cycle to check whether the problem has been solved.

 If this is not the case, contact an authorised Technical Assistance Centre.

 Always request the assistance of authorised technicians.

Have the following information to hand:

 the type of problem;

 the appliance model (Mod.);

 the serial number (S/N).

This information can be found on the data plate applied to the rear of the washing machine, and can also be found

on the front of the appliance by opening the door.

Slovensky

PRÁÈKA

Obsah

Intalácia, 14-15

Rozbalenie a vyrovnanie do vodorovnej polohy

Pripojenie kelektrickej akvodovodnej sieti

Prvý prací cyklus

Technické údaje

Popis práèky, 16-17

Ovládací panel

Displej

Ako vykona prací cyklus, 18

Programy a volite¾né funkcie, 19

Tabu¾ka pracích programov

Volite¾né funkcie prania

Pracie prostriedky a prádlo, 20

Dávkovaè pracích prostriedkov

Príprava prádla

peciálne programy

Opatrenia a rady, 21

Základné bezpeènostné pokyny

Likvidácia

Manuálne otvorenie dvierok

Údrba a starostlivos, 22

Uzavretie prívodu vody a vypnutie elektrického

napájania

Èistenie práèky

Èistenie dávkovaèa pracích prostriedkov

Èistenie èerpadla

Kontrola prítokovej hadice na vodu

Poruchy a spôsob ich odstránenia, 23

Servisná sluba, 24

PWSE 6108 W

Návod na pouitie

Intalácia

 Je ve¾mi dôleité uschova tento návod kvôli

prípadnému ïaliemu pouitiu. Vprípade predaja,

darovania alebo presahovania práèky sa uistite, e

zostane uloený vjej blízkosti, aby mohol poslúi

novému majite¾ovi pri oboznámení sa sèinnosou a

spríslunými upozorneniami.

 Pozorne si preèítajte uvedené pokyny: obsahujú

dôleité informácie, týkajúce sa intalácie, pouitia a

bezpeènosti pri práci.

Rozbalenie a vyrovnanie do vodorovnej

polohy

Rozbalenie

1. Rozba¾te práèku.

2. Skontrolujte, èi poèas prepravy nedolo kjej

pokodeniu. Vprípade, e je pokodená, nezapájajte

ju a obráte sa na predajcu.

3. Odstráòte 4 skrutky

slúiace na ochranu

poèas prepravy agumovú

podloku sprísluným

ditanèným èlenom, ktoré

sa nachádzajú vzadnej

èasti (viï obrázok).

4. Uzatvorte otvory po skrutkách plastovými krytkami z

prísluenstva.

5. Uschovajte vetky diely: vprípade opätovnej

prepravy práèky ich bude potrebné opätovne

namontova.

 Obaly nie sú hraèky pre deti!

Vyrovnanie do vodorovnej polohy

1. Práèku je potrebné umiestni na rovnú a pevnú

podlahu tak, aby nebola opretá ostenu, nábytok alebo

onieèo iné.

2. Vprípade, e podlaha

nie je dokonale

vodorovná, môu by

prípadné rozdiely

vykompenzované

odskrutkovaním alebo

zaskrutkovaním predných

noièiek (viï obrázok);

Uhol sklonu, nameraný

na pracovnej ploche,

nesmie presiahnu 2°.

Dokonalé vyrovnanie do vodorovnej polohy zabezpeèí

stabilitu zariadenia a zamedzí vzniku vibrácií a hluku

poèas èinnosti. Vprípade intalácie na podlahovú

krytinu alebo na koberec, nastavte noièky tak, aby

pod práèkou zostal dostatoèný vo¾ný priestor na

ventiláciu.

Pripojenie kelektrickej akvodovodnej sieti

Pripojenie prítokovej hadice vody

1. Pripojte prívodnú hadicu

jej zaskrutkovaním ku

kohútiku so studenou

vodou, shrdlom so

závitom 3/4 (viï

obrázok).

Pred pripojením hadice

nechajte vodu odtiec, a

kým nebude èíra.

2. Pripojte prítokovú

hadicu kpraèke, jej

zaskrutkovaním k

príslunej prípojke na

vodu, umiestnenej vpravo

hore (viï obrázok).

3. Zabezpeète, aby hadica nebola príli ohnutá alebo

stlaèená.

 Tlak vrozvode vody sa musí pohybova vrozmedzí

hodnôt uvedených vtabu¾ke s technickými údajmi (viï

ved¾ajia strana).

 Vprípade, e dåka prítokovej hadice nebude

dostatoèná, obráte sa na pecializovanú predajòu

alebo na autorizovaný technický personál.

 Nikdy nepouívajte u pouité hadice.

 Pouívajte hadice zprísluenstva zariadenia.

Pripojenie vypúacej hadice

Pripojte vypúaciu

hadicu kodpadovému

potrubiu alebo kodpadu v

stene, nachádzajúcom

sa od 65 do 100 cm nad

zemou; jednoznaène

zamedzte jej ohybu.

alebo ju uchyte k okraju

umývadla èi vane, a

pripevnite vodiaci driak

zprísluenstva ku

kohútu (viï obrázok).

Vo¾ný koniec vypúacej

hadice nesmie zosta

ponorený do vody.

 Pouitie predlovacích hadíc sa neodporúèa; ak je

vak nevyhnutné, predlovacia hadica musí ma

rovnaký priemer ako originálna hadica a jej dåka

nesmie presiahnu 150 cm.

Pripojenie kelektrickej sieti

Pred zasunutím zástrèky do zásuvky sa uistite, e:

 zásuvka je uzemnená a e vyhovuje normám;

 zásuvka je schopná unies maximálnu záa

odpovedajúcu menovitému príkonu zariadenia,

uvedenému vtabu¾ke s technickými údajmi (viï

ved¾a);

 hodnota napájacieho napätia odpovedá údajom

uvedeným vtabu¾ke stechnickými údajmi (viï

ved¾a);

 zásuvka je kompatibilná so zástrèkou práèky.

Vopaènom prípade je potrebné vymeni zásuvku

alebo zástrèku.

 Práèka nesmie by umiestnená vonku  pod holým

nebom, a to ani vprípade, keby sa jednalo o miesto

chránené pred nepriazòou poèasia, pretoe je ve¾mi

nebezpeèné vystavi ju daïu a búrkam.

 Po ukonèení intalácie musí zásuvka zosta ¾ahko

prístupná.

65 - 100 cm

 Nepouívajte predlovacie káble a rozvodky.

 Kábel nesmie by ohnutý alebo pritlaèený.

 Výmena kábla musí by zverená výhradne

autorizovanému technickému personálu.

Upozornenie! Výrobca neponesie iadnu zodpovednos

za následky spôsobené nerepektovaním týchto

pokynov.

Prvý prací cyklus

Po intalácii zariadenia je potrebné ete pred jeho

pouitím vykona jeden skúobný cyklus spracím

prostriedkom a bez náplne prádla, nastavením

pracieho programu .

Technické údaje

Model

PWSE 6108 W

Rozmery

šírka 59,5 cm

výška 85 cm

håbka 44,5 cm

Kapacita

od 1 do 6 kg

Pripojenie

k elektrickej sieti

viï títok s technickými

údajmi, aplikovaný na

zariadení

Pripojenie

k vodovodnému

rozvodu

maximálny tlak 1 MPa

(10 bar)

minimálny tlak 0,05 MPa

(0,5 bar)

kapacita bubna 40 litrov

Rýchlos

odstreïovania

a do 1000 otáèok za minútu

Kontrolný program

pod¾a normy

EN 60456

program 2, teplota 60°C,

vykonané so 6 kg náplòou.

Toto zariadenie je v zhode

s nasledujúcimi smernicami

Európskej únie:

-89/336/EHS z 03/05/89

(Elektromagnetická

kompatibilita) v platnom

znení

- 2006/95/ES

-2006/95/ES (Nízke napätie)

Popis práèky

Ovládací panel

Tlaèidlo TEPLOTA

OTOÈNÝ OVLÁDAÈ

PROGRAMOV

Dávkovaè pracích prostriedkov

Tlaèidlo ON/OFF

Tlaèidlo

ODSTREÏOVANIE

Tlaèidlo a kontrolka

START/PAUSE

DISPLEJ

Tlaèidlo

ONESKORENÝ TART

Tlaèidlá a kontrolky

VOLITE¼NÝCH

FUNKCIÍ

Kontrolka

ZABLOKOVANÉ

DVIERKA

Dávkovaè pracích prostriedkov: slúi na dávkovanie

pracích prostriedkov a prídavných prostriedkov (viï

Pracie prostriedky a prádlo).

Tlaèidlo ON/OFF

: krátke stlaèenie tohtotlaèidla

slúi na zapnutie alebo vypnutie práèky. Kontrolka

START/PAUSE, ktorá pomaly bliká modrou farbou

signalizuje, e stroj je zapnutý. Ak chcete vypnú

práèku poèas prania, je potrebné dra tlaèidlo

stlaèené dlhie, pribline 3 sek.; krátkym alebo

náhodným stlaèením práèku nevypnete.

Vypnutie zariadenia poèas prania spôsobí zruenie

prebiehajúceho pracieho programu.

OTOÈNÝ OVLÁDAÈ PROGRAMOV: Slúi na

nastavenie poadovaného programu (viï Tabu¾ka

programov).

Tlaèidlá akontrolky VOLITE¼NÝCH FUNKCIÍ: Slúia

navo¾bu jednotlivých ponúknutých volite¾ných funkcií.

Kontrolka zvolenej funkcie zostane rozsvietená.

Tlaèidlo ODSTREÏOVANIE

: Stlaète pre zníenie

alebo úplné vyradenie odstreïovania; hodnota bude

uvedená na displeji.

Tlaèidlo TEPLOTA

: Stlaète pre zníenie alebo

úplné vyradenie ohrevu; hodnota bude uvedená na

displeji.

Tlaèidlo ONESKORENÝ TART

: Stlaète kvôli

nastaveniu oneskoreného tartu zvoleného programu;

nastavené oneskorenie bude zobrazené na displeji.

Tlaèidlo a kontrolka START/PAUSE

: Keï modrá

kontrolka zaène pomaly blika, stlaète toto tlaèidlo,

aby ste spustili pranie. Po zahájení cyklu sa kontrolka

rozsvieti stálym svetlom. Ak chcete pranie prerui,

opätovne stlaète toto tlaèidlo; kontrolka bude blika

jantárovým svetlom. Ak symbol

nie je rozsvietený,

bude moné otvori dvierka. Pre opätovné zahájenie

prania zbodu, v ktorom bolo preruené, opätovne

stlaète toto tlaèidlo.

Kontrolka ZABLOKOVANÉ DVIERKA

Rozsvietený symbol signalizuje, e dvierka sú

zaistené. Aby sa dvierka nepokodili, pred ich

otvorením je potrebné vyèka, kým uvedený symbolu

nezhasne.

Ak chcete otvori dvierka poèas pracieho cyklu, stlaète

tlaèidlo START/PAUSE; keï bude kontrolka

ZABLOKOVANÉ DVIERKA

zhasnutá, bude moné

dvierka otvori.

Pohotovostný reim

Kvôli zhode snovými predpismi súvisiacimi s

energetickou úsporou, je táto práèka vybavená

systémom automatického vypnutia (prechodu do

pohotovostného reimu  standby), ktorý je

aktivovaný po uplynutí nieko¾kých minút, ak práèka

nie je pouívaná. Krátko stlaète tlaèidlo ON/OFF

avyèkajte na obnovenie èinnosti zariadenia.

Displej

Displej slúi na programovanie zariadenia ana poskytovanie mnohých informácií.

Vèasti A je zobrazovaná doba trvania rôznych programov a po zahájení èinnosti aj doby zostávajúcej do jeho

ukonèenia; vprípade nastavenia ONESKORENÝ TART bude zobrazená doba zostávajúca do zahájenia zvoleného

programu.

Okrem toho, pri stlaèení prísluného tlaèidla budú zobrazené maximálne hodnoty rýchlosti odstreïovania a teploty,

ktoré zariadenie môe dosiahnu, vzávislosti od nastaveného programu.

Presýpacie hodiny budú blika vo fáze, keï zariadenie spracúva údaje na základe zvoleného programu aúrovne

Smart. Maximálne po 10 minútach od zahájenia programu prestanú presýpacie hodiny blika adôjde kzobrazeniu

definitívneho zvyného èasu. Ikona presýpacích hodín prestane by zobrazovaná pribline po uplynutí 1 minúty od

zobrazenia definitívneho zvyného èasu.

Vèasti B sú zobrazované fázy prania, ktoré sú súèasou zvoleného cyklu a po zahájení programu aj prebiehajúce

fázy prania:

Pranie

Plákanie

Odstreïovanie

Odèerpanie vody

V èasti C sa nachádzajú ikony  z¾ava doprava  teplota, odstreïovanie a Oneskorený tart.

Pruhy teplota

znázoròujú úroveò teploty vzh¾adom kmaximálnej nastavite¾nej hodnote pre daný cyklus.

Pruhy odstreïovanie

znázoròujú úroveò odstreïovania vzh¾adom kmaximálnej nastavite¾nej hodnote pre daný

cyklus.

Rozsvietený symbol Oneskorený tart

signalizuje , e na zariadení bola zvolená funkcia Oneskoreného tartu.

Ako vykona prací cyklus

1. ZAPNUTIE ZARIADENIA. Stlaète tlaèidlo ;

kontrolka START/PAUSE bude pomaly blika

modrým svetlom.

2. NAPLÒTE PRÁÈKU PRÁDLOM. Otvorte dvierka.

Naplòte práèku prádlom prièom dbajte, aby nedolo

kprekroèeniu mnostva náplne, uvedeného

vtabu¾ke programov na nasledujúcej strane.

3. NAPLÒTE DÁVKOVAÈ PRACÍCH

PROSTRIEDKOV. Vytiahnite dávkovaè pracích

prostriedkov a naplòte prací prostriedok do

prísluných priehradiek, spôsobom vysvetleným

vèasti Pracie prostriedky a prádlo.

4. ZATVORTE DVIERKA.

5. ZVO¼TE PRACÍ PROGRAM. Otoèným ovládaèom

PROGRAMOV zvo¾te poadovaný program; teplotu

arýchlos odstreïovania pre zvolený je moné

meni. Na displeji sa zobrazí doba trvania cyklu.

6. NASTAVTE PRACÍ PROGRAM POD¼A VAICH

POTRIEB. Pouite prísluné tlaèidlá:

Zmeòte teplotu a/alebo rýchlos

odstreïovania. Zariadenie automaticky zobrazuje

maximálnu teplotu a rýchlos odstreïovania pre

nastavený program alebo posledné zvolené hodnoty,

ak sú vhodné pre zvolený program. Stlaèením

tlaèidla

je moné postupne zníi teplotu prania

a po pranie v studenej vode OFF. Stlaèením

tlaèidla

je moné postupne zníi rýchlos

odstreïovania a po jeho úplné vylúèenie OFF.

Ïalie stlaèenie tlaèidiel obnoví nastavenie

maximálnych prednastavených hodnôt.

Nastavenie oneskoreného tartu.

Pre nastavenie oneskoreného tartu zvoleného

programu stláèajte prísluné tlaèidlo, a kým

nenastavíte poadovanú dobu oneskorenia. Keï je

táto funkcia zvolená, na displeji sa rozsvieti symbol

. Na zruenie oneskoreného tartu je potrebné

stláèa tlaèidlo, a kým sa na displeji nezobrazí

symbol OFF.

Zmena vlastností cyklu.

 Stlaète tlaèidlo za úèelom aktivácie volite¾nej

funkcie; rozsvieti sa prísluná kontrolka.

 Opätovným stlaèením môete zvolenú volite¾nú

funkciu zrui; prísluná kontrolka zhasne.

 Vprípade, e zvolená volite¾ná funkcia nie je

kompatibilná snastaveným pracím programom,

kontrolka zaène blika a volite¾ná funkcia nebude

aktivovaná.

 Ak zvolená funkcia nie je kompatibilná s niektorou

u nastavenou volite¾nou funkciou, kontrolka prvej

zvolenej funkcie bude blika abude aktivovaná len

druhá; kontrolka zvolenejfunkcie sa rozsvieti.

Poznámka: Ak je zvolená funkcia SMART,

akáko¾vek ïalia nekompatibilná funkcia nebude

môc by aktivovaná.

 Volite¾né funkcie môu zmeni uvedenú náplò a/

alebo dobu trvania daného cyklu.

7. SPUSTE PROGRAM. Stlaète tlaèidlo START/

PAUSE. Prísluná kontrolka sa rozsvieti stálym

modrým svetlom a dôjde k zablokovaniu dvierok

(rozsvieti sa symbol ZABLOKOVANÉ DVIERKA

Ak chcete zmeni program poèas prebiehajúceho

cyklu, aktivujte preruenie cyklu práèky stlaèením

tlaèidla START/PAUSE (kontrolka START/PAUSE

bude blika jantárovým svetlom); potom zvo¾te

poadovaný program aznovu stlaète tlaèidlo

START/PAUSE.

Ak chcete otvori dvierka poèas pracieho cyklu,

stlaète tlaèidlo START/PAUSE; keï bude kontrolka

ZABLOKOVANÉ DVIERKA

zhasnutá, bude

moné otvori dvierka. Opätovným stlaèením tlaèidla

START/PAUSE opätovne uveïte do èinnosti prací

program zbodu, v ktorom bol preruený.

8. UKONÈENIE PROGRAMU. Bude signalizované

zobrazením nápisu END na displeji apo zhasnutí

symbolu ZABLOKOVANÉ DVIERKA

bude moné

otvori dvierka. Otvorte dvierka, vylote prádlo a

vypnite zariadenie.

 Ak si eláte zrui u zahájený cyklus, stlaète dlhie

tlaèidlo

. Cyklus bude preruený a dôjde kvypnutiu

zariadenia.

Systém automatického vyváenia náplne

Pred kadým odstreïovaním bubon vykoná otáèanie

rýchlosou o málo prevyujúcou rýchlos prania, aby

sa tak odstránili vibrácie aaby sa náplò rovnomerne

rozloila. Vprípade, e po nieko¾ko násobných

pokusoch o vyváenie prádlo ete nebude správne

vyváené, zariadenie vykoná odstreïovanie niou

rýchlosou, ako je prednastavená rýchlos. Ak je

práèka nadmerne nevyváená, vykoná namiesto

odstreïovania vyváenie. Za úèelom dosiahnutia

rovnomernejieho rozloenia náplne a jej správneho

vyváenia, odporúèa sa pomiea ve¾ké a malé kusy

prádla.

Programy a volite¾né

funkcie

Volite¾né funkcie prania

Volite¾ná funkcia umoòuje optimalizova

pranie vzávislosti od mnostva prádla skutoène

naloeného do práèky, pri skrátení èasu,spotreby

vody a energie. Stlaèením tlaèidla

je ïalej

moné zvoli poadovaný druh prania.

Intensive: Energické pranie znaène zneèisteného

prádla.

4 You: tandardné pranie bene zneèisteného prádla.

Fast: Rýchle pranie mierne zneèisteného prádla.

 Je moné ho aktivova len pri programoch 1, 2, 3, 4, 5, 6

(vetky tri úrovne) a 7, 8, 9 (úrovne 4 You aFast).

Extra Plákanie

Vo¾bou tejto volite¾nej funkcie sa zvýi úèinnos

plákania a zaistí sa maximálny stupeò odstránenia

pracieho prostriedku. Je uitoèná hlavne pre

mimoriadne citlivé pokoky.

 Nie je aktivovate¾ná vprogramoch 9, , .

¼ahké ehlenie

Vo¾bou tejto volite¾nej funkcie bude pranie a

odstreïovanie náleite zmenené, aby sa predilo tvorbe

záhybov. Na konci cyklu práèka vykoná pomalé

otáèanie bubna; kontrolka funkcie ¼AHKÉ EHLENIE a

kontrolka START/PAUSE budú blika (prvá modrým

adruhá jantárovým svetlom). Na ukonèenie cyklu je

potrebné stlaèi tlaèidlo START/PAUSE alebo tlaèidlo

¼AHKÉ EHLENIE. Vprograme 11-13 zariadenie ukonèí

cyklus snamoèeným prádlom a budú blika kontrolky

¼AHKÉ EHLENIE aSTART/PAUSE. Pre odèerpanie

vody a vyloenie prádla je potrebné stlaèi tlaèidlo

START/PAUSE alebo tlaèidlo ¼AHKÉ EHLENIE.

 Túto funkciu nie je moné aktivova vprogramoch 9,

10, 12,

, .

Odstraòovanie kvàn

Táto funkcia je uitoèná na

odstránenie najodolnejích

kvàn. Vlote prídavnú

nádobku 4 zprísluenstva

do priehradky 1. Pri

dávkovaní bieliaceho

prostriedku neprekraèujte

úroveò max vyznaèenú

na stredovom èape(viï

obrázok). Na vykonanie

samotného bielenia nalejte

bieliaci prostriedok do prídavnej priehradky 4, nastavte

program Plákanie

aaktivujte volite¾nú funkciu

Odstraòovanie kvàn

. Na bielenie poèas prania

naplòte dávkovaè pracími prostriedkami aprísadami,

nastavte poadovaný program aaktivujte volite¾nú

funkciu Odstraòovanie kvàn

. Pouitie prídavnej

nádobky 4 vyluèuje monos predpierania.

Túto funkciu nie je moné aktivova vprogramoch

1, 7, 9, 10, 11, 12, 13,

, .

Pracie prostriedky a prídavné

prostriedky

Popis programu

Max.

teplota

(°C)

Max.

rýchlos

(otáèky za

minútu)

Pred

piera

nie

Pran

Bieliaci

prostri

edok

Avivá

Max.

náplò

(kg)

Doba

trvania

cyklu

Kadodenné

1 Bavlna s predpieraním:

Mimoriadne zneèistené biele prádlo.

90° 1000

• • - •

2 Biela bavlna:

Mimoriadne zneèistené biele prádlo.

90° 1000

- • • •

2 Biela bavlna (1):

Znaène zneèistené biele a farebné prádlo z odolných tkanín.

60° 1000

- • • •

2 Bavlna (2):

Znaène zneèistené biele a farebné prádlo z chúlostivých tkanín.

40° 1000

- • • •

3 Bavlna:

Znaène zneèistené biele a farebné prádlo z odolných tkanín.

60° 1000

- • • •

4 Farebná bavlna (3):

Málo zneèistené biele a chúlostivé farebné prádlo.

40° 1000

- • • •

5 Syntetické:

Velmi zneèistené farebné prádlo z odolných tkanín. 60° 800

- • • •

2,5

6 Syntetické:

Èiastoène zneèistené farebné prádlo z odolných tkanín.

40° 800

- • • •

2,5

7 Dínsy

40° 800

- • - •

8 Košele

40° 600

- • • •

Mix-Cool 30':

K rýchlemu oiveniu ¾ahko zneèisteného prádla (nedoporuèuje

sa pre vlnu, hodváb a prádlo urèené na pranie v rukách).

studene

j vode

800

- • - •

Špeciálne

10 Vlna:

Pre vlnu, kamír, atï.

40° 600

- • - •

1,5

11 Hodváb/Záclony:

Pre prádlo z hodvábu, viskózy, spodné prádlo. 30° 0

- • - •

12 Sport Shoes

30° 600

- • - •

2 páry

13 Outwear

30° 400

- • - -

Dielèie

Plákanie - 1000

- - • •

Odstreïovanie - 1000

- - - -

Odèerpanie vody - 0

- - - -

Tabu¾ka pracích programov

Pracie

programy

Je moné kontrolova dobu trvania pracích programov na displeji.

Pre vetky Test Institutes:

1) Kontrolný program pod¾a normy EN 60456: nastavte program 2 steplotou 60°C.

2) Dlhý program na pranie bavlny: nastavte program 2 steplotou 40°C.

3) Krátky program na pranie bavlny: nastavte program 4 steplotou 40°C.

Pracie prostriedky a prádlo

Dávkovaè pracích prostriedkov

Dobrý výsledok prania závisí aj od správneho

dávkovania pracieho prostriedku: pouitie nadmerného

mnostva zniuje efektivitu prania a napomáha tvorbe

vodného kameòa na vnútorných èastiach práèky a

zvyuje zneèistenie ivotného prostredia.

 Nepouívajte pracie prostriedky urèené na pranie v

rukách, pretoe spôsobujú tvorbu nadmerného

mnostva peny.

Pri vyahovaní dávkovaèa pracích prostriedkov a pri

jeho plnení pracími alebo prídavnými prostriedkami

postupujte nasledovne.

Priehradka 1: Prací

prostriedok na

predpieranie (prákový)

Pred naplnením priehradky

pracím prostriedkom sa

uistite, e vdávkovaèi nie je

vloená prídavná priehradka 4.

Priehradka 2: Prací

prostriedok na pranie

(prákový alebo tekutý)

Tekutý prací prostriedok sa nalieva len tesne pred

zahájením pracieho cyklu.

Priehradka 3: Prídavné prostriedky (avivá, atï.)

Avivá nesmie vyteka zmrieky.

prídavná priehradka 4: Bieliaci prostriedok

Príprava prádla

 Roztrieïte prádlo pod¾a:

- druhu tkaniny / symbolu na visaèke.

- farby: odde¾te farebné prádlo od bieleho.

 Vyprázdnite vrecká a skontrolujte gombíky.

 Neprekraèujte povolenú náplò, vzahujúcu sa na

hmotnos suchého prádla:

Odolné tkaniny: max. 6 kg

Syntetické tkaniny: max. 2,5 kg

Chúlostivé tkaniny: max. 2 kg

Vlna: max. 1,5 kg

Hodváb: max. 1 kg

Ko¾ko vái prádlo?

1 plachta 400-500 g

1 oblieèka 150-200 g

1 obrus 400-500 g

1 upan 900-1.200 g

1 uterák 150-250 g

peciálne programy

Jeans: Prevráte prádlo naruby a pouite tekutý prací

prostriedok. Pouite program 7.

Koele: pouite prísluný program 8 na pranie koie¾

z odliných druhov tkanín a odliných farieb.

Zaruèuje maximálnu starostlivos pri minimalizácii

tvorby záhybov.

Mix-Cool 30': bol navrhnutý pre pranie mierne

zneèisteného prádla vpriebehu krátkej doby: trvá len 30

minút a etrí tak energiu aj èas. Nastavením programu 9

je moné pra spolu prádlo z tkanín rôzneho druhu (s

výnimkou vlny a hodvábu) smaximálnou náplòou 3 kg.

Vlna: s programom 10 je moné pra vpráèke vetky

druhy prádla z vlny, vrátane tých, ktoré sú oznaèené

visaèkou len ruèné pranie

. Na dosiahnutie

optimálnych výsledkov pouívajte vhodný prací

prostriedok aneprekraèujte hmotnos prádla 1,5 kg.

Hodváb: pouite prísluný program 11 na pranie

vetkého prádla z hodvábu. Odporúèa sa pouitie

pracieho prostriedku pre chúlostivé prádlo.

Záclony: poskladajte ich a ulote dovnútra oblieèky

alebo do sáèku zo sieoviny. Pouite program 11.

Sport Shoes (program 12) bol navrhnutý pre pranie

portovej obuvi; pre dosiahnutie optimálnych výsledkov

neperte viac ako 2 páry naraz.

Outwear (program 13) bol navrhnutý pre pranie

hydrofóbnych látok a vetroviek (napr. z goratexu,

polyesteru, nylónu); pre dosiahnutie optimálnych

výsledkov pouite tekutý prací prostriedok a dávku

vhodnú pre poloviènú náplò; predbene oetrite

manety, goliere a kvrny; nepouívajte avivá alebo

pracie prostriedky s aviváou. Spouitím tohto

programu je moné pra ipáperové vetrovky.

Stránka sa načítava ...

Indesit PWSE 6108 W (EU) Užívateľská príručka

Značka: Indesit

Model: PWSE 6108 W (EU)

Kategória: Práčky

Typ: Užívateľská príručka

Stiahnite si PDF

správa

V iných jazykoch

English: Indesit PWSE 6108 W (EU) User guide

Indesit PWSE 6108 W (EU) Užívateľská príručka

Indesit PWSE 6108 W (EU) Užívateľská príručka

V iných jazykoch

Súvisiace články

Ďalšie dokumenty