Makita PLM4627N Používateľská príručka

Kategória
Kosačky na trávu
Typ
Používateľská príručka
GB Petrol Lawn Mower Instruction manual
FTondeuse Thermique Manuel d’instructions
DBenzin-Rasenmäher Betriebsanleitung
IRasaerba con motore a benzina Istruzioni per l’uso
ECortadora de Césped a Gasolina Manual de instrucciones
PCortador de Grama a Gasolina Manual de instruções
SBensindriven gräsklippare Bruksanvisning
NBensindrevet gressklipper Bruksanvisning
FIN Bensiinikäyttöinen ruohonleikkuri Käyttöohje
LV Benzīna zāles pļaujmašīna Instrukciju rokasgrāmata
LT Benzininė žoliapjovėNaudojimo instrukcija
EE Bensiinimootoriga muruniiduk Kasutusjuhend
PL Spalinowa kosiarka do trawy Instrukcja obsługi
HU Benzinmotoros fűnyíró Használati utasítás
SK Benzínová kosačka Návod na obsluhu
CZ Benzínová sekačka na trávu Návod k obsluze
SI Kosilnica z bencinskim motorjem Navodila za uporabo
AL Kositëse bari me naftë Manuali i perdorimit
BG Бензинова косачка за трева Инструкция за работа
HR Benzinska kosilica za travu Priručnik s uputama za
uporabu
MK Бензинска косилка Упатство за употреба
RO Maşină de tuns iarba pe bază de Manual de instrucţiuni
benzină
RS Бензинска косилица за траву Приручник са упутствима
RUS Бензогазонокосилка Инструкция по
эксплуатации
UA Бензинова газонокосарка Інструкція з експлуатації
PLM4626N
PLM4627N
PLM4628N
2
A PLM4628N
B PLM4626N C PLM4627N
1
2
4
5
6
7
8
17
3
16
14
18
15
9
10
11
12
13
3
1A 1B
1C 1D
1E 1F
19
20
21
4
1G 1H
1I 1J
23A
22
15
23
5
3B 3C
45
6A 6B
6
7A 7B
8A 8B
8C 8D
24
7
910
11 12
13
25
26
8
ENGLISH (Original instructions)
CONTENTS
SECTION 1 SYMBOLS MARKED ON THE PRODUCT (on the rear cover) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
SECTION 2 GENERAL SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
SECTION 3 PARTS DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
SECTION 4 TECHNICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
SECTION 5 ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
SECTION 6 “3 IN 1” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
SECTION 7 OPERATING INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
SECTION 8 MAINTENANCE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
SECTION 9 LUBRICATION INSTRUCIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
SECTION 10 CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
SECTION 11 STORAGE INSTRUCTIONS (OFF SEASON) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
SECTION 12 TROUBLESHOOTING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
SECTION 13 WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
SECTION 14 ENVIRONMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
SECTION 15 EC DECLARATION OF CONFORMITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
9
Explanation of general view
WARNING:
For your own safety please read this manual before
attempting to operate your new unit. Failure to follow
instructions can result in serious personal injury. Spend a
few moments to familiarize yourself with your mower
before each use. Keep this manual in a safe place, so that
the information is available at all times. If you give the
equipment to any other person, hand over these operating
instructions and safety regulations as well.
Intended use
The equipment may only be used for the tasks it is
designed to handle. Any other use is deemed to be a case
of misuse. The user/operator and not the manufacturer
will be liable for any damage or injuries of any kind caused
as a result of this.
The petrol lawn mower is intended for private use i.e. for
use in home and gardening environments.
Private use of the lawn mower refers an annual operating
time generally not exceeding that of 50 hours, during
which time the machine is primarily used to maintain
small-scale, residential lawns and home/hobby gardens.
Public facilities, sporting halls, and agricultural/forestry
applications are excluded.
Please note that our equipment has not been designed for
use in commercial, trade or industrial applications. Our
warranty will be voided if the machine is used in
commercial, trade or industrial businesses or for
equivalent purposes.
The operating instructions as supplied by the
manufacturer must be kept and referred to in order to
ensure that the lawn mower is properly used and
maintained. The instructions contain valuable information
on operating, maintenance and servicing conditions.
Important! Due to the high risk of bodily injury to the user,
the lawn mower may not be used to trim bushes, hedges
or shrubs, to cut scaling vegetation, planted roofs, or
balcony-grown grass, to clean (suck up) dirt and debris off
walkways, or to chop up tree or hedge clippings.
Moreover, the lawn mower may not be used as a power
cultivator to level out high areas such as molehills.
For safety reasons, the lawn mower may not be used as a
drive unit for other work tools or tool kits of any kind.
1. SYMBOLS MARKED ON THE
PRODUCT (on the rear cover)
1. Upper handle
2. Brake control handle
3. Choke lever
4. Starter handle
5. Rope guide
6. Locking lever
7. Grass catch bag
8. Height adjusting lever
9. Discharge channel
10. Sideward flap
11. Deck
12. Spark plug
13. Fuel cap
14. Oil cap
15. Cable clamp
16. Lower handle
17. Self-drive control handle
18. Mulching wedge
19. Bolt
20. Washer
21. Locking knob
22. Lock nut
23. The angle adjusting gear
24. Primer bulb
25. Tab
26. Filter cover
Read operator’s manual.
Keep bystanders away.
Pay more attention to the operator’s hands
and feet to avoid injury.
Fuel is flammable, keep fire away. Do not add
fuel with running machine.
Toxic fumes; don’t operate inside house.
When mowing, please wear the glasses and
ear plugs to defend the operator himself.
When repairing, please pick up the spark
plug, and then repair it according to the
operational manual.
Caution: Engine hot.
10
Safety Label Found On Lawn Mower: KEEP HANDS AND
FEET AWAY
WARNING: Keep the safety signs clear and
visible on the equipment. Replace the safety signs if they
are missing or illegible.
2. GENERAL SAFETY RULES
WARNING: When using petrol tools, basic safety
precautions, including the following, should always be
followed to reduce the risk of serious personal injury and/
or damage to the unit. Read all these instruction before
operating this product and retain these instructions for
future reference.
WARNING: This machine produces an
electromagnetic field during operation. This field may
under some circumstances interfere with active or passive
medical implants. To reduce the risk of serious or fatal
injury, we recommend persons with medical implants to
consult their physician and the medical implant
manufacturer before operating this machine.
Training
Read the instructions carefully. Be familiar with the
controls and the proper use of the equipment.
Learn how to stop the engine quickly.
Only use the lawn mower for the purpose for which it
was designed, i.e. for cutting and collecting grass. Any
other use can be hazardous, causing damage to the
machine. Examples of improper use may include, but
are not limited to:
- transport of people, children or animals on the
machine;
- being transported by the machine;
- using the machine to tow or push loads;
- using the machine for leaf or debris collection;
- using the machine to trim hedges, or for cutting
vegetation other than grass;
- use of the machine by more than one person;
- using the blade on surfaces other than grass.
Never allow children or people unfamiliar with these
instructions to use the lawn mower. Local regulations
can restrict the age of the operator.
Never use the lawn mower:
- when people, especially children, or pets are
nearby;
- if the operator has taken medicine or substances
that can affect his ability to react and concentrate.
Keep in mind that the operator or user is responsible
for accidents or hazards occurring to other people or
their property.
The operators must receive proper training in the use,
adjustment and operation of the machine, including
prohibited operations.
Preparation
While mowing, always wear substantial footwear and
long trousers. Do not operate the equipment when
barefoot or wearing open sandals;
Thoroughly inspect the area where the equipment is to
be used and remove all objects, such as stones, toys,
sticks and wires, which can be thrown by the machine.
WARNING - Petrol is highly flammable.
- Store fuel in containers specifically designed for this
purpose;
- Refuel outdoors only and do not smoke while
refueling;
- Add fuel before starting the engine. Never remove
the cap of the fuel tank or add petrol while the
engine is running or when the engine is hot;
- If petrol is spilled, do not attempt to start the engine
but move the machine away from the area of
spillage and avoid creating any source of ignition
until petrol vapours have dissipated;
- Replace all fuel tank and container caps securely;
Replace faulty silencers;
Before using, always visually inspect to see that the
blades, blade bolts and cutter assembly are not worn or
damaged. Replace worn or damaged blades and bolts
in sets to preserve balance.
Check regularly to ensure that all starting interlocks
and operator presence controls are properly
functioning.
Operation
Do not operate the engine in a confined space where
dangerous carbon monoxide fumes can collect;
Do not use the machine while being tired, ill or under
influence of alcohol or other drugs.
Warning! Do not use the lawn mower when there is a
risk for lighting.
It is recommended to limit the duration of operation, in
order to minimize the risks from noise and vibration.
Be careful when using the lawn mower in slopes and
near drop-offs, ditches or embankments.
Mow only in daylight or in good artificial light;
Avoid operating the equipment in wet grass, where
feasible;
Always be sure of your footing on slopes;
Walk, never run;
For wheeled rotary machines, mow across the face of
slopes, never up and down;
Exercise extreme caution when changing direction on
slopes;
Do not mow excessively steep slopes;
Use extreme caution when reversing or pulling the
lawn mower towards you;
Stop the blade(s) if the lawn mower has to be tilted for
transportation when crossing surfaces other than
grass, and when transporting the lawn mower to and
from the area to be mowed;
Never operate the lawn mower with defective guards,
or without safety devices, for example deflectors and/or
grass catchers, in place;
11
Caution: The lawn mower shall not be operated without
either the entire grass catcher or self-closing discharge
opening guard in place.
Do not change the engine governor settings or
overspeed the engine;
Do not alter or tamper with any sealed adjustment for
the engine speed control.
The lawn mower safety systems or features shall not
be tampered with or disabled.
Disengage all blades and drive clutches before starting
the engine;
Start the engine carefully according to instructions and
with feet well away from the blade(s);
Do not tilt the lawn mower when starting the engine;
Do not start the engine when standing in front of the
discharge chute;
Do not put hands or feet near or under rotating parts.
Keep clear of the discharge opening at all times;
Never pick up or carry a lawn mower while the engine
is running;
Stop the engine and disconnect the spark plug wire,
make sure that all moving parts have come to a
complete stop and, where a key is fitted remove the
key:
- Before clearing blockages or unclogging chute;
- Before checking, cleaning or working on the lawn
mower;
- After striking a foreign object. Inspect the lawn
mower for damage and make repairs before
restarting and operating the lawn mower;
- If lawn mower starts to vibrate abnormally (check
immediately);
Stop the engine and disconnect the spark plug wire,
make sure that all moving parts have come to a
complete stop and, where a key is fitted remove the
key:
- Whenever you leave the lawn mower;
- Before refueling;
Reduce the throttle setting during engine shut down
and, if the engine is provided with a shut-off valve, turn
the fuel off at the conclusion of mowing.
Maintenance and storage
Keep all nuts, bolts and screws tight to be sure the
equipment are in safe working condition;
Never store the equipment with petrol in the tank inside
a building where fumes can reach an open flame or
spark;
Allow the engine to cool before storing in any
enclosure; Clean and maintain the lawn mower before
storage.
To reduce the fire hazard, keep the engine, silencer,
battery compartment and petrol storage area free of
grass, leaves, or excessive grease;
Check the grass catcher frequently for wear or
deterioration;
Replace worn or damaged parts for safety;
If the fuel tank has to be drained, this should be done
outdoors.
Improper maintenance, use of non-conforming
replacement components, or the removal or
modification of safety components can damage the
lawn mower and injure the operators seriously.
Only use the recommended blades and spare parts by
the manufacturer. The use of non-genuine parts can
damage the machine and injure the operators. Keep
the lawn mower in good working condition.
If the blade stopping device doesn’t work, please
contact service center for help.
Transportation and handling
Whenever the machine is to be handled, raised,
transported or tilted you must:
- wear strong working gloves;
- grasp the machine at the points that offer a safe grip,
taking account of the weight and its distribution;
- use an appropriate number of people for the weight
of the machine and the characteristics of the vehicle
or the place where it has to be placed or collected.
During transport, fasten the machine securely with
ropes or chains.
WARNING: Do not touch rotating blade.
WARNING: Refuel in a well ventilated area with
the engine stopped.
3. PARTS DESCRIPTION (Fig. A
& B, C)
Including
A: Spark plug wrench
12
4. TECHNICAL DATA
Differences between three models
5. ASSEMBLY
5-1 FOLDING HANDLE
1. Use the locking knob to fix the lower handlebars into
the unit body. (Fig. 1A/Fig. 1B/Fig. 1C/Fig. 1D)
2. Lift the two locking levers to release the upper
handlebars for folding. (Fig. 1E)
3. Push the locking lever closed to lock the handlebars in
the operating position. (Fig. 1F)
4. Adjust the tension by turning the lock nut with a
suitable spanner. (Fig. 1G/Fig. 1H)
5. Attach the cable-clamp to the position shown and then
attach the cable. (Fig. 1I/Fig. 1J)
5-2 ADJUSTMENT FOR AN
APPROPRIATE ANGLE
A) Pull the locking lever opening;
B) Rotating the upper handle centered of the angle
adjusting gear for adjusted an appropriate angle into
the scope –20° to 20° (5 position: –20°/–10°/0°/10°/
20°) as the Fig. 2 shown;
C) Push the locking lever closed to connect the lower
handle and the upper handle.
5-3 MOUNTING THE GRASS CATCHER
1. To fit: Raise the rear cover and hitch the grass catcher
on rear of mower. (Fig.3A/Fig.3B/Fig.3C)
2. To remove: Grasp and lift rear cover, remove grass
catcher.
5-4 STARTER HANDLE
Move the starter handle from the engine to the rope guide.
(Fig. 4)
5-5 HEIGHT OF CUT
Apply outward pressure to disengage lever from rack.
Move lever forward or back to adjust height. (Fig. 5 and
see clause 7.9)
Model PLM4626N PLM4627N PLM4628N
Engine type B&S500E, 09P6 B&S500E, 09P6 B&S500E, 09P6
Self-propelled no no yes
Engine displacement 140 cm3140 cm3140 cm3
Nominal Power 1.9 kW 1.9 kW 1.9 kW
Blade width 460 mm 460 mm 460 mm
Rated speed 2,800/min 2,800/min 2,800/min
Fuel tank capacity 800 ml 800 ml 800 ml
Oil capacity 470 ml 470 ml 470 ml
Grass catcher capacity 60 L 60 L 60 L
Net weight 28.0 kg 28.4 kg 31.2 kg
Height adjustment 25 - 75 mm, 7 adjustment 25 - 75 mm, 7 adjustment 25 - 75 mm, 7 adjustment
Model Front handle of
deck Side discharge Self-propelled
PLM4626N ××
PLM4627N ×
PLM4628N
Model PLM4626N PLM4627N PLM4628N
Guaranteed sound power level at the
operator’s position
(According to EN ISO 5395-1 Annex F &
EN ISO 5395-2, EN ISO 4871)
86.9 dB (A) (K=3 dB (A)) 86.9 dB (A) (K=3 dB (A)) 86.9 dB (A) (K=3 dB (A))
Measured sound power level 93.7 dB (A)
K=2.38 dB (A)
93.7 dB (A)
K=2.38 dB (A)
93.7 dB (A)
K=2.38 dB (A)
Guaranteed sound power level
(According to 2000/14/EC) 96 dB (A) 96 dB (A) 96 dB (A)
Vibration
(According to EN ISO 5395-1 Annex G
& EN ISO 5395-2)
4.531 m/s2
K=1.5 m/s24.531 m/s2
K=1.5 m/s24.531 m/s2
K=1.5 m/s2
13
6. “3 IN 1” (only for PLM4627N,
PLM4628N)
These lawn mowers can be retrofitted from its normal
function, based on the application purpose:
From lawn mower with rear discharge to:
1. Mulching mower or as
2. Side-discharge mower.
What is mulching?
When mulching, the grass is cut in one working step, then
finely chopped and returned to the grass strip as natural
fertilizer.
Hints for mulch-mowing:
- Regular cut-back by max. 2 cm from 6 cm to 4 cm
grass height.
- Use a sharp cutting knife - Do not mow wet grass
- Set max. motor speed
- Only move at working pace
- Regularly clean mulching wedge, housing inner side
and mowing blade
Starting Operation
ONE: Retrofitting for mulching mower
WARNING: Only with a stopped motor and
standstill cutter.
1. Raise the rear cover and remove the grass catch bag.
2. Push the mulching wedge into the deck. Lock the
mulching wedge with the button into the opening on
the deck. (Fig. 6A/Fig. 6B)
3. Lower the rear cover again.
TWO: Resetting for side-discharge mowing
Only when motor and cutting are at standstill!
1. Lift the rear cover and remove the grass catch bag.
2. Mount the mulching wedge.
3. Lift sideward flap for side discharge. (Fig. 7A)
4. Mount the discharge channel, for side discharge on
the support pin of the sideward flap. (Fig. 7A)
5. Lower the sideward flap- the flap lies on the discharge
channel. (Fig. 7B)
THREE: Mowing with the grass catch bag
WARNING: Only with a stopped motor and
standstill cutter.
For mowing with the grass catch bag, remove the
mulching wedge and discharge channel for side discharge
and mount the grass catch bag.
1. Removing the mulching wedge.
- Lift rear cover and remove the mulching wedge.
2. Lift sideward flap and remove discharge channel.
- Removing the discharge channel for side discharge.
- The sideward flap automatically closes the
discharge opening on the housing by mean of spring
force.
- Regularly clean the sideward flap and discharge
opening form grass rest and stuck dirt.
3. Mount the grass catch bag.
- To fit: Raise the rear cover and hitch the grass catch
bag on rear of mower.
- To remove: Grasp and lift the rear cover, remove
grass catch bag.
7. OPERATING INSTRUCTIONS
7-1 BEFORE STARTING
Service the engine with gasoline and oil as instructed in
the separate engine manual packed in your mower. Read
instructions carefully.
WARNING: Petrol is highly flammable.
Store fuel in containers specifically designed for this
purpose.
Refuel outdoors only, before starting the engine and do
not smoke while refueling or handling fuel.
Never remove the cap of the fuel tank or add petrol while
the engine is running or when the engine is hot.
If petrol is spilled, do not attempt to start the engine but
move the machine away from the area of spillage and
avoid creating any source of ignition until petrol vapors
have dissipated.
Replace all fuel tanks and container caps securely.
Before tipping the lawn mower to maintain the blade or
drain oil, remove fuel from tank.
WARNING: Never fill fuel tank indoors, with
engine running or until the engine has been allowed to
cool for at least 15 minutes after running.
7-2 TO START ENGINE AND ENGAGE
BLADE
1. The unit is equipped with a rubber boot over the end of
the spark plug, make certain the metal loop on the end
of the spark plug wire (inside the rubber boot) is
fastened securely over the metal tip on the spark plug.
2. Press the primer bulb 3-5 times before starting the
engine. (Fig. 8A)
3. When starting cool engine, turn throttle choke lever to
” position.
When starting warm engine and operating, turn
throttle choke lever to ” position. (Fig. 8B)
4. Standing behind the unit, grasp the brake control
handle and hold it against the upper handle as shown.
(Fig. 8C)
5. Grasp the starter handle as shown (Fig. 8C) and pull
up rapidly. Return it slowly to the rope guide bolt after
engine starts.
Release the brake control handle to stop the engine and
blade. (Fig. 8D)
Start the engine carefully according to
instructions and with feet well away from the blade.
Do not tilt the lawn mower when starting the
engine. Start the mower on a level surface, free of high
grass or obstacles.
14
Keep hands and feet away from the rotating
parts. Do not start the engine when standing in front of the
discharge opening.
7-3 OPERATION PROCEDURES
During operation, tightly hold the brake handle with both
hands.
NOTE: During operation, when the brake handle
is released, the engine will stop and thus stopping the
lawn mower from operating.
WARNING: In order to avoid any unintentional
start-ups of the lawn mower, it comes equipped with an
engine brake which must be pulled back before the
engine can be started. When the engine control lever is
released it must return to its initial position, at which point
the engine automatically switches off.
NOTE: Engine brake (brake handle): Use the
lever to stop the engine. When you release the lever the
engine and the blade stop automatically. To mow, hold the
lever in the working position. Before you start to mow,
check the start/stop lever several times to be sure that it is
working properly. Ensure that the tension cable can be
smoothly operated (i.e. is not catching or kinking in any
way).
7-4 TO STOP ENGINE
CAUTION: The blade continues to rotate for a
few seconds after the engine is shut off.
1. Release the brake control handle to stop the engine
and blade.
2. Disconnect and ground the spark plug wire as
instructed in the separate engine manual to prevent
accidental starting while equipment is unattended.
7-5 CONNECTION FOR AUTO MOVE
For PLM4628N
Grip the self-drive control handle, the lawn mower will
move forward automatically with about 3.6 km/h (Fig. 9),
release the self-drive handle, the lawn mower will stop
move.
CAUTION: Your mower is designed to cut normal
residential grass of a height no more than 250 mm.
Do not attempt to mow through unusually tall dry or wet
grass (e.g., pasture) or piles of dry leaves. Debris may
build up on the mower deck or contact the engine exhaust
presenting a potential fire hazard.
7-6 FOR THE BEST RESULTS WHEN
MOWING
Clear lawn of debris. Be sure that the lawn is clear of
stones, sticks, wire or other foreign objects which could be
accidentally thrown out by the mower in any direction and
cause serious personal injury to the operator and others
as well as damage to property and surrounding objects.
Do not cut wet grass. For effective mowing do not cut wet
grass because it tends to stick to the underside of the
deck preventing proper mowing of the grass clippings. Cut
no more than 1/3 the length of the grass. The
recommended cut for mowing is 1/3 the length of the
grass. Ground speed will need to be adjusted so the
clippings can be dispersed evenly into the lawn. For
especially heavy cutting in thick grass it may be
necessary to use one of the slowest speeds in order to get
a clean well mowed cut. When mowing long grass you
may have to cut the lawn in two passes, lowering the
blade another 1/3 of the length for the second cut and
perhaps cutting in a different pattern than was used the
first time. Overlapping the cut a little on each pass will
also help to clean up any stray clippings left on the lawn.
The mower should always be operated at full throttle to
get the best cut and allow it to do the most effective job of
mowing. Clean underside of deck. Be certain to clean the
underside of the cutting deck after each use to avoid a
build-up of grass, which would prevent proper mulching.
Mowing leaves. The mowing of leaves can also be
beneficial to your lawn. When mowing leaves make sure
they are dry and are not laying too thick on the lawn. Do
not wait for all the leaves to be off the trees before you
mow.
WARNING: If you strike a foreign object, stop the
engine. Remove wire from spark plug, thoroughly inspect
the mower for any damage and repair the damage before
restarting and operating the mower. Extensive vibration of
the mower during operation is an indication of damage.
The unit should be promptly inspected and repaired.
7-7 GRASS CATCHER
There is a window on the rear cover. You can see the
condition of grass catcher through the window. If the
catcher is full of grass; you will empty and clean the bag,
make sure it is clean and ensure its meshwork is
ventilated. (Fig. 10)
7-8 DECK
The underside of the mower deck should be cleaned after
each use to prevent a buildup of grass clippings, leaves,
dirt or other matter. If this debris is allowed to accumulate,
it will invite rust and corrosion, and may prevent proper
mulching. The deck may be cleaned by tilting the mower
and scraping clean with a suitable tool (make certain the
spark plug wire is disconnected).
7-9 HEIGHT ADJUSTMENT
INSTRUCTIONS
CAUTION: Do not at any time make any
adjustment to lawn mower without first stopping the
engine and disconnecting the spark plug wire.
CAUTION: Before changing mowing height, stop
mower and disconnect spark plug cable.
15
Your mower is equipped with a central height
adjustment lever offering 7 height positions.
1. Stop mower and disconnect spark plug cable before
changing mower cutting height.
2. The central height adjustment lever offers you 7
different height positions.
3. To change the height of cut, squeeze adjuster lever
toward the wheel, moving up or down to selected
height. (Fig. 11)
All wheels will be in the same height of cut.
8. MAINTENANCE
INSTRUCTIONS
SPARK PLUG
Use only original replacement spark plug. For best results,
replace the spark plug every 100 hours of use.
BRAKE PADS
Check and/or replace the engine brake pads in service
agent regularly, only original parts can be used as
replacement.
9. LUBRICATION INSTRUCTIONS
CAUTION: DISCONNECT SPARK PLUG
BEFORE SERVICING.
1. WHEELS - Lubricate the ball bearings in each wheel
at least once a season with a light oil.
2. ENGINE - Follow engine manual for lubrication
instructions.
10. CLEANING
CAUTION: Do not hose engine. Water can
damage engine or contaminate the fuel system.
1. Wipe deck with dry cloth.
2. Hose under deck by tilting the mower so that the spark
plug is up.
10-1 ENGINE AIR CLEANER
CAUTION: Do not allow dirt or dust to clog the air
filter foam element. The engine air cleaner element must
be serviced (cleaned) after 25 hours normal mowing. The
foam element must be serviced regularly if the mower is
used in dry dusty conditions.
To CLEAN AIR FILTER
1. Lift the tabs on top of the filter cover.
2. Remove the filter cover.
3. Wash filter element in soap water. DO NOT USE
GASOLINE!
4. Air dry filter element.
5. Place a few drops of SAE30 oil on the foam filter and
squeeze tightly to remove any excess oil.
6. Reinstall filter.
7. Close the filter cover.
NOTE: Replace filter if frayed, torn, damaged or
unable to be cleaned. (Fig. 12)
10-2 CUTTING BLADE
CAUTION: Be sure to disconnect and ground the
spark plug wire before working on the cutting blade to
prevent accidental engine starting. Protect hands by using
heavy gloves or a rag to grasp the cutting blades. Tip
mower as specified in separate engine manual. Remove
the hex bolt and washer which hold the blade and blade
adapter to the engine crankshaft. Remove the blade and
adapter from the crankshaft.
WARNING: Periodically inspect the blade
adapter for cracks, especially if you strike a foreign object.
Replace when necessary.
For best results your blade should be sharp. The blade
may be resharpened by removing it and either grinding or
filing the cutting edge keeping as close to the original
bevel as possible. It is extremely important that each
cutting edge receives an equal amount of grinding to
prevent an unbalanced blade. Improper blade balance will
result in excessive vibration causing eventual damage to
the engine and mower. Be sure to carefully balance blade
after sharpening. The blade can be tested for balance by
balancing it on a round shaft screwdriver. Remove metal
from the heavy side until it balances evenly.
Before reassembling the blade and the blade adapter to
the unit, lubricate the engine crankshaft and the inner
surface of the blade adapter with light oil. Install the blade
adapter on the crankshaft. Refer to Fig. 13. Place the
blade with the part number facing away from the adapter.
Align the washer over the blade and insert the hex bolt.
Tighten the hex bolt to the torque listed below:
10-3 BLADE MOUNTING TORQUE
Center bolt 35 Nm - 45 Nm, to insure safe operation of
your unit. All nuts and bolts must be checked periodically
for correct tightness.
After prolonged use, especially in sandy soil conditions,
the blade will become worn and lose some of the original
shape. Cutting efficiently will be reduced and the blade
should be replaced. Replace with an approved factory
replacement blade only. Possible damage resulting from
blade unbalance condition is not the responsibility of the
manufacturer.
When you change the blade, you must use the original
type marked on the blade (Makita 263001451) (to order
the blade, please contact your local dealer or call our
company, see cover page).
10-4 ENGINE
Refer to the separate engine manual for engine
maintenance instructions.
Maintain engine oil as instructed in the separate engine
manual packed with your unit. Read and follow
instructions carefully.
Service air cleaner as per separate engine manual under
normal conditions.
16
Clean every few hours under extremely dusty conditions.
Poor engine performance and flooding usually indicates
that the air cleaner should be serviced.
To service the air cleaner, refer to the separate engine
manual packed with your unit.
The spark plug should be cleaned and the gap reset once
a season. Spark plug replacement is recommended at the
start of each mowing season; check engine manual for
correct plug type and gap specifications.
Clean the engine regularly with a cloth or brush. Keep the
cooling system (blower housing area) clean to permit
proper air circulation which is essential to engine
performance and life. Be certain to remove all grass, dirt
and combustible debris from muffler area.
11. STORAGE INSTRUCTIONS
(OFF SEASON)
The following steps should be taken to prepare lawn
mower for storage.
1. Empty the tank after the last mowing of the season.
a) Empty the petrol tank with a suction pump.
CAUTION: Do not drain the petrol in closed
rooms, in close proximity of open fire, etc. Do not smoke!
Petrol fumes can cause explosion or fire.
b) Start the engine and let it run until it has used up all
remaining petrol and stalls.
c) Remove the spark plug. Use an oilcan to fill approx.
20 ml oil into the combustion chamber. Operate the
starter to evenly distribute the oil in the combustion
chamber. Replace the spark plug.
2. Clean and grease the lawn mower carefully as
described above under “LUBRICATION
INSTRUCTIONS”.
3. Slightly grease the cutter to avoid corrosion.
4. Store the lawn mower in a dry, clean and frost-
protected place, out of reach of unauthorized persons.
CAUTION: The engine must have completely
cooled down before storing the lawn mower.
NOTE:
- When storing any type of power equipment in an
unventilated or material storage shed:
- Care should be taken to rust-proof the equipment.
Using a light oil or silicone, coat the equipment,
especially cables and all moving parts.
- Be careful not to bend or kink cables.
- If the starter rope becomes disconnected from rope
guide on handle, disconnect and ground the spark plug
wire, depress the blade control handle and pull the
starter rope out from engine slowly. Slip the starter rope
into the rope guide bolt on handle.
Transport
Turn the engine off and allow the engine to cool down.
Then disconnect the spark plug wire and empty the fuel
tank according to the instructions in the engine manual.
Ensure not to bend or damage the cutter when pushing
the lawn mower over obstacles.
17
12. TROUBLESHOOTING GUIDE
PROBLEM PROBABLE CAUSE CORRECTIVE ACTION
Engine does not start. Throttle choke not in the correct position
for the prevailing conditions.
Move throttle choke to correct position.
Fuel tank is empty. Fill tank with fuel: refer to ENGINE
OWNERS MANUAL.
Air cleaner element is dirty. Clean air cleaner element: refer to
ENGINE OWNERS MANUAL.
Spark plug loose. Tighten spark plug to 25-30 Nm.
Spark plug wire loose or disconnected
from plug.
Install spark plug wire on spark plug.
Spark plug gap is incorrect. Set gap between electrodes at 0.7 to
0.8 mm.
Spark plug is defective. Install new, correctly gapped plug: refer
to ENGINE OWNERS MANUAL.
Carburetor is flooded with fuel. Remove air cleaner element and pull
starter rope continuously until carburetor
clears itself and install air cleaner
element.
Faulty ignition module. Contact the service agent.
Engine difficult to start or loses
power.
Dirt, water, or stale fuel tank. Drain fuel and clean tank. Fill tank with
clean, fresh fuel.
Vent hole in fuel tank cap is plugged. Clean or replace fuel tank cap.
Air cleaner element is dirty. Clean air cleaner element.
Engine operates erratically. Spark plug is defective. Install new, correctly gapped plug: refer
to ENGINE OWNERS MANUAL.
Spark plug gap is incorrect. Set gap between electrodes at 0.7 to
0.8 mm.
Air cleaner element is dirty. Clean air cleaner element: refer to
ENGINE OWNERS MANUAL.
Engine idles poorly. Air cleaner element is dirty. Clean air cleaner element: refer to
ENGINE OWNERS MANUAL.
Air slots in engine shroud are blocked. Remove debris from slots.
Cooling fins and air passages under
engine blower housing are blocked.
Remove debris from cooling fins and air
passages.
Engine skips at high speed. Gap between electrodes of spark plug is
too close.
Set gap between electrodes at 0.7 to
0.8 mm.
Engine overheats. Cooling air flow is restricted. Remove any debris from slots in shroud,
blower housing, air passages.
Incorrect spark plug. Install RC12YC or QC12YC spark plug
and cooling fins on engine.
Mower vibrates abnormally. Cutting assembly is loose. Tighten blade.
Cutting assembly is unbalanced. Balance blade.
18
13. WARRANTY
This product is warranted in accordance with legal
regulations for a 12 months period effective from the date
of purchase by the first user.
This warranty covers all material or production failures, it
does not include defects from normal wear & tear parts,
such as bearings, brushes, cables, plugs or accessories
like drills, drill bits, saw blades etc.; damage or defects
resulting from abuse, accidents or alterations; nor the
costs for transport.
We reserve the right to reject any claim where the
purchase cannot be verified or when it is clear that the
product was not maintained properly. (Clean ventilation
slots, carbon brushes serviced regularly.)
Your purchase ticket must be kept as proof for date of
purchase.
Your un-dismantled tool must be returned to your dealer in
an acceptably clean state, in its original blow molded case
if applicable to unit, accompanied by your proof of
purchase.
14. ENVIRONMENT
Should your machine need replacement after extended
use, do not put it in the domestic waste but dispose of it in
an environmentally safe way.
15. EC DECLARATION OF
CONFORMITY
For European countries only
Makita declares that the following machine(s):
Designation of Machine:
Petrol Lawn Mower
Model No./Type: PLM4626N, PLM4627N, PLM4628N
Specifications: See “4. TECHNICAL DATA”
Conforms to the following European Directives:
2004/108/EC, 2006/42/EC, 2000/14/EC & 2005/88/EC
They are manufactured in accordance with the following
standard or standardized documents:
EN ISO 5395-1, EN ISO 5395-2, EN ISO 14982
The technical file in accordance with 2006/42/EC is
available from:
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium
The conformity assessment procedure required by
Directive 2000/14/EC was in accordance with annex VI.
Notified body:
TÜV SÜD Industrie Service GmbH
Westendstrasse 199, D-80686 München,
Deutschland
Identification number: 0036
PLM4626N
Measured sound power level: 93.7 dB (A)
Guaranteed sound power level: 96 dB (A)
PLM4627N
Measured sound power level: 93.7 dB (A)
Guaranteed sound power level: 96 dB (A)
PLM4628N
Measured sound power level: 93.7 dB (A)
Guaranteed sound power level: 96 dB (A)
22.8.2014
Yasushi Fukaya
Director
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium
19
FRANÇAIS (Instructions d’origine)
TABLE DES MATIÈRES
SECTION 1 SYMBOLES MARQUÉS SUR LE PRODUIT (sur le couvercle arrière) . . . . . . . . . . . . . . . . . . . . . . . . . .20
SECTION 2 CONSIGNES DE SÉCURITÉ GÉNÉRALES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
SECTION 3 DESCRIPTION DES PIÈCES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
SECTION 4 CARACTÉRISTIQUES TECHNIQUES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
SECTION 5 MONTAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
SECTION 6 « 3 EN 1 » . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
SECTION 7 INSTRUCTIONS D’UTILISATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
SECTION 8 INSTRUCTIONS DE MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
SECTION 9 INSTRUCTIONS DE LUBRIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
SECTION 10 NETTOYAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
SECTION 11 INSTRUCTIONS D’ENTREPOSAGE (HORS SAISON) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
SECTION 12 GUIDE DE DÉPANNAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
SECTION 13 GARANTIE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
SECTION 14 ENVIRONNEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
SECTION 15 DÉCLARATION DE CONFORMITÉ CE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
20
Descriptif
AVERTISSEMENT :
Pour votre sécurité, veuillez lire ce manuel avant de faire
fonctionner votre nouvelle machine. Le non-respect des
instructions peut provoquer de graves blessures
corporelles. Prenez le temps de vous familiariser avec la
tondeuse avant chaque utilisation. Conservez ce manuel
en lieu sûr pour que les informations soient constamment
à votre disposition. Si vous donnez l’appareil à quelqu’un,
transmettez également ce mode d’emploi ainsi que les
consignes de sécurité.
Utilisation prévue
Cet appareil ne saurait être utilisé que pour les tâches
pour lesquelles il a été conçu. Toute autre utilisation sera
considérée comme une mauvaise utilisation. L’utilisateur/
opérateur (non pas le fabricant) sera tenu responsable de
tout dommage matériel ou corporel de toute sorte en
résultant.
La tondeuse thermique est conçue pour un usage privé, à
savoir dans un environnement domestique et pour le
jardinage.
Par usage privé de la tondeuse, on entend une durée de
fonctionnement annuelle ne dépassant pas généralement
50 heures pendant lesquelles la machine est
principalement utilisée pour entretenir de petits jardins,
des pelouses résidentielles et des jardins particuliers ou
familiaux. Les installations publiques, les terrains de sport
et les applications agricoles ou forestières sont exclus.
Veuillez noter que notre appareil n’a pas été conçu pour
des applications commerciales, professionnelles ou
industrielles. Notre garantie sera nulle et non avenue si la
machine est utilisée dans des activités commerciales,
professionnelles ou industrielles, ou à des fins
équivalentes.
Le mode d’emploi fourni par le fabricant doit être conservé
et consulté afin de garantir que la tondeuse sera
correctement utilisée et entretenue. Les instructions
renferment des informations précieuses sur les conditions
de fonctionnement, d’entretien et de dépannage.
Important ! En raison du risque élevé de blessures
corporelles pour l’utilisateur, la tondeuse ne saurait être
utilisée pour couper des buissons, des haies ou des
arbustes, pour couper des plantes grimpantes, des toits
végétalisés ou de l’herbe poussant sur balcon, pour
nettoyer (aspirer) la poussière et les débris des trottoirs
ou pour couper des arbres ou les résidus de haie. En
outre, la tondeuse ne saurait être utilisée comme
motoculteur pour aplanir des zones élevées comme les
taupinières.
Par mesure de sécurité, la tondeuse ne saurait être
utilisée comme unité d’entraînement pour d’autres outils
de travail ou kits d’outil de toute sorte.
1. SYMBOLES MARQUÉS SUR
LE PRODUIT (sur le couvercle
arrière)
1. Guidon supérieur
2. Guidon de commande du frein
3. Levier de l’étrangleur
4. Guidon de démarrage
5. Guide câble
6. Levier de sécurité
7. Sac de ramassage
8. Levier de réglage de la hauteur
9. Canal d’éjection
10. Volet latéral
11. Plateau
12. Bougie d’allumage
13. Capuchon du carburant
14. Bouchon d’huile
15. Serre-câble
16. Guidon inférieur
17. Guidon d’autopropulsion
18. Coin de hachage
19. Boulon
20. Rondelle
21. Bouton de verrouillage
22. Contre-écrou
23. Pignon de réglage angulaire
24. Poire d’amorçage
25. Languette
26. Couvercle du filtre
Lisez le manuel d’instructions.
Éloignez les spectateurs.
Pour éviter de vous blesser, protégez vos
mains et vos pieds.
Le carburant est inflammable, tenez-le
éloigné des flammes. N’ajoutez pas de
carburant lors du fonctionnement de la
machine.
Fumées toxiques, n’utilisez pas en intérieur.
Lorsque vous tondez, portez des lunettes et
des bouchons d’oreilles pour votre sécurité.
Lors de la réparation, retirez la bougie
d’allumage, puis réparez-la conformément au
manuel d’instructions.
Attention : moteur chaud.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229
  • Page 230 230
  • Page 231 231
  • Page 232 232
  • Page 233 233
  • Page 234 234
  • Page 235 235
  • Page 236 236
  • Page 237 237
  • Page 238 238
  • Page 239 239
  • Page 240 240
  • Page 241 241
  • Page 242 242
  • Page 243 243
  • Page 244 244
  • Page 245 245
  • Page 246 246
  • Page 247 247
  • Page 248 248
  • Page 249 249
  • Page 250 250
  • Page 251 251
  • Page 252 252
  • Page 253 253
  • Page 254 254
  • Page 255 255
  • Page 256 256
  • Page 257 257
  • Page 258 258
  • Page 259 259
  • Page 260 260
  • Page 261 261
  • Page 262 262
  • Page 263 263
  • Page 264 264
  • Page 265 265
  • Page 266 266
  • Page 267 267
  • Page 268 268
  • Page 269 269
  • Page 270 270
  • Page 271 271
  • Page 272 272
  • Page 273 273
  • Page 274 274
  • Page 275 275
  • Page 276 276
  • Page 277 277
  • Page 278 278
  • Page 279 279
  • Page 280 280
  • Page 281 281
  • Page 282 282
  • Page 283 283
  • Page 284 284
  • Page 285 285
  • Page 286 286
  • Page 287 287
  • Page 288 288

Makita PLM4627N Používateľská príručka

Kategória
Kosačky na trávu
Typ
Používateľská príručka