Indesit IWC 7105 ECO (EE) Užívateľská príručka

Značka: Indesit

Model: IWC 7105 ECO (EE)

Kategória: Práčky

Typ: Užívateľská príručka

Contents

Installation, 2-3

Unpacking and levelling

Connecting the electricity and water supplies

The first wash cycle

Technical data

Description of the washing machine

and starting a wash cycle, 4-5

Control panel

Indicator lights

Starting a wash cycle

Wash cycles, 6

Table of wash cycles

Personalisation, 7

Setting the temperature

Setting the spin speed

Functions

Detergents and laundry, 8

Detergent dispenser drawer

Preparing the laundry

Garments requiring special care

Load balancing system

Precautions and tips, 9

General safety

Disposal

Care and maintenance, 10

Cutting off the water or electricity supply

Cleaning the washing machine

Cleaning the detergent dispenser drawer

Caring for the door and drum of your appliance

Cleaning the pump

Checking the water inlet hose

Troubleshooting, 11

Service, 12

IWC 7105

Instructions for use

WASHING MACHINE

English,1

Românã,25

Óêðà¿íñüêà,49

Polski,37

Slovensky,13

Installation

 This instruction manual should be kept in a safe

place for future reference. If the washing machine is

sold, transferred or moved, make sure that the

instruction manual remains with the machine so that

the new owner is able to familiarise himself/herself

with its operation and features.

 Read these instructions carefully: they contain vital

information relating to the safe installation and

operation of the appliance.

Unpacking and levelling

Unpacking

1. Remove the washing machine from its packaging.

2. Make sure that the washing machine has not been

damaged during the transportation process. If it has

been damaged, contact the retailer and do not

proceed any further with the installation process.

3. Remove the 4

protective screws (used

during transportation) and

the rubber washer with

the corresponding

spacer, located on the

rear part of the appliance

(see figure).

4. Close off the holes using the plastic plugs provided.

5. Keep all the parts in a safe place: you will need

them again if the washing machine needs to be

moved to another location.

 Packaging materials should not be used as toys for

children.

Levelling

1. Install the washing machine on a flat sturdy floor,

without resting it up against walls, furniture cabinets

or anything else.

2. If the floor is not

perfectly level, compen-

sate for any unevenness

by tightening or loosening

the adjustable front feet

(see figure); the angle of

inclination, measured in

relation to the worktop,

must not exceed 2°.

Levelling the machine correctly will provide it with

stability, help to avoid vibrations and excessive noise

and prevent it from shifting while it is operating. If it is

placed on carpet or a rug, adjust the feet in such a

way as to allow a sufficient ventilation space

underneath the washing machine.

Connecting the electricity and water

supplies

Connecting the water inlet hose

1. Connect the supply

pipe by screwing it to a

cold water tab using a ¾

gas threaded connection

(see figure).

Before performing the

connection, allow the

water to run freely until it

is perfectly clear.

2. Connect the inlet hose

to the washing machine

by screwing it onto the

corresponding water inlet

of the appliance, which is

situated on the top right-

hand side of the rear part

of the appliance (see

figure).

3. Make sure that the hose is not folded over or bent.

 The water pressure at the tap must fall within the

values indicated in the Technical details table (see

next page).

 If the inlet hose is not long enough, contact a

specialised shop or an authorised technician.

 Never use second-hand hoses.

 Use the ones supplied with the machine.

Technical data

Model

IWC 7105

Dimensions

width 59.5 cm

height 85 cm

depth 53,5 cm

Capacity

from 1 to 7 kg

Electrical

connections

please refer to the technical data

plate fixed to the machine

Water connections

maximum pressure 1 MPa (10 bar)

minimum pressure 0.05 MPa (0.5 bar)

drum capacity 52 litres

Spin speed

up to 1000 rotations per minute

Energy rated

programmes

according to

regulation

EN 60456

programme 2; temperature 60°C;

using a load of 7 kg.

This appliance conforms to the

following EC Directives:

- 2004/108/EC (Electromagnetic

Compatibility)

- 2002/96/EC

- 2006/95/EC (Low Voltage)

65 - 100 cm

Connecting the drain hose

Connect the drain hose,

without bending it, to a

drainage duct or a wall

drain located at a height

between 65 and 100 cm

from the floor;

alternatively, rest it on

the side of a washbasin

or bathtub, fastening the

duct supplied to the tap

(see figure). The free end

of the hose should not

be underwater.

 We advise against the use of hose extensions; if it is

absolutely necessary, the extension must have the

same diameter as the original hose and must not

exceed 150 cm in length.

Electrical connections

Before plugging the appliance into the electricity

socket, make sure that:

 the socket is earthed and complies with all

applicable laws;

 the socket is able to withstand the maximum power

load of the appliance as indicated in the Technical

data table (see opposite);

 the power supply voltage falls within the values

indicated in the Technical data table (see opposite);

 the socket is compatible with the plug of the

washing machine. If this is not the case, replace

the socket or the plug.

 The washing machine must not be installed

outdoors, even in covered areas. It is extremely

dangerous to leave the appliance exposed to rain,

storms and other weather conditions.

 When the washing machine has been installed, the

electricity socket must be within easy reach.

 Do not use extension cords or multiple sockets.

 The cable should not be bent or compressed.

 The power supply cable must only be replaced by

authorised technicians.

Warning! The company shall not be held responsible

in the event that these regulations are not respected.

The first wash cycle

Once the appliance has been installed, and before

you use it for the first time, run a wash cycle with

detergent and no laundry, using the wash cycle 2.

Detergent dispenser drawer: used to dispense

detergents and washing additives (see Detergents

and laundry).

ON/OFF button: switches the washing machine on

and off.

WASH CYCLE knob: programmes the wash cycles.

During the wash cycle, the knob does not move.

FUNCTION buttons with indicator light: used to

select the available functions. The indicator light

corresponding to the selected function will remain lit.

TEMPERATURE knob: sets the temperature or the

cold wash cycle (see Personalisation).

SPIN SPEED knob: sets the spin speed or exclude

the spin cycle completely (see Personalisation).

WASH CYCLE PROGRESS/DELAY TIMER

indicator light

s: used to monitor the progress of the

wash cycle.

The illuminated indicator light shows which phase is in

progress.

If the Delay Timer function has been set, the time

remaining until the wash cycle starts will be indicated

(see next page).

DOOR LOCKED indicator light: indicates whether

the door may be opened or not (see next page).

START/PAUSE button with indicator light: starts or

temporarily interrupts the wash cycles.

N.B. To pause the wash cycle in progress, press this

button; the corresponding indicator light will flash

orange, while the indicator light for the current wash

cycle phase will remain lit in a fixed manner. If the

DOOR LOCKED

indicator light is switched off, the

door may be opened.

To start the wash cycle from the point at which it was

interrupted, press this button again.

Standby mode

This washing machine, in compliance with new

energy saving regulations, is fitted with an automatic

standby system which is enabled after about 30

minutes if no activity is detected. Press the ON-OFF

button briefly and wait for the machine to start up

again.

Description of the washing machine

and starting a wash cycle

WASH CYCLE PROGRESS/

DELAY TIMER

indicator lights

DOOR LOCKED

indicator light

START/

PAUSE

button with

indicator light

Control panel

Detergent dispenser drawer

ON/OFF

button

WASH CYCLE

knob

TEMPERATURE

knob

FUNCTION

buttons with

indicator lights

SPIN SPEED

knob

Indicator lights

The indicator lights provide important information.

This is what they can tell you:

Delayed start

If the DELAY TIMER function has been activated (see

Personalisation), after the wash cycle has been

started the indicator light corresponding to the

selected delay period will begin to flash:

As time passes, the remaining delay will be displayed

and the corresponding indicator light will flash:

The set programme will start once the selected time

delay has expired.

Wash cycle phase indicator lights

Once the desired wash cycle has been selected and has

begun, the indicator lights switch on one by one to

indicate which phase of the cycle is currently in progress.

Function buttons and corresponding indicator lights

When a function is selected, the corresponding

indicator light will illuminate.

If the selected function is not compatible with the

programmed wash cycle, the corresponding indicator

light will flash and the function will not be activated.

If the selected function is not compatible with another

function which has been selected previously, the

indicator light corresponding to the first function

selected will flash and only the second function will be

activated; the indicator light corresponding to the

enabled option will remain lit.

Door locked indicator light

When the indicator light is on, the porthole door is

locked to prevent it from being opened; make sure

the indicator light is off before opening the door (wait

approximately 3 minutes). To open the door during a

running wash cycle, press the START/PAUSE button;

the door may be opened once the DOOR LOCKED

indicator light turns off.

Starting a wash cycle

1. Switch the washing machine on by pressing the ON/OFF button. All indicator lights will switch on for a few

seconds, then they will switch off and the START/PAUSE indicator light will pulse.

2. Load the laundry and close the door.

3. Set the WASH CYCLE knob to the desired programme.

4. Set the washing temperature (see Personalisation).

5. Set the spin speed (see Personalisation).

6. Measure out the detergent and washing additives (see Detergents and laundry).

7. Select the desired functions.

8. Start the wash cycle by pressing the START/PAUSE button and the corresponding indicator light will remain lit

in a fixed manner, in green.

To cancel the set wash cycle, pause the machine by pressing the START/PAUSE button and select a new cycle.

9. At the end of the wash cycle the

indicator light will switch on. The door can be opened once the DOOR

LOCKED

indicator light turns off. Take out your laundry and leave the appliance door ajar to make sure the

drum dries completely. Switch the washing machine off by pressing the ON/OFF button.

Wash

Rinse

Spin

Drain

End of wash cycle

Specials wash cycles

Express (wash cycle 10) this wash cycle was designed to wash lightly soiled garments quickly: it lasts just 15 minutes

and therefore saves both energy and time. By selecting this wash cycle (10 at 30°C), it is possible to wash different

fabrics together (except for wool and silk items), with a maximum load of 1.5 kg.

Sport Intensive (

wash cycle

11) is for washing heavily soiled sports clothing fabrics (tracksuits, shorts, etc.);

for best results, we recommend not exceeding the maximum load indicated in the "Table of wash cycles".

Sport Light (

wash cycle

12) is for washing lightly soiled sports clothing fabrics (tracksuits, shorts, etc.); for best

results, we recommend not exceeding the maximum load indicated in the "Table of wash cycles". We recommend

using a liquid detergent and dosage suitable for a half-load.

Sport Shoes (

wash cycle

13) is for washing sports shoes; for best results, do not wash more than 2 pairs

simultaneously.

Wash cycles

The information contained in the table is intended as a guide only.

For all Test Institutes:

1) Test wash cycle in compliance with regulation EN 60456: set wash cycle 2 with a temperature of 60°C.

2) Long wash cycle for cottons: set wash cycle 2 with a temperature of 40°C.

3) Short wash cycle for cottons: set wash cycle 4 with a temperature of 40°C.

Wash cycles

Table of wash cycles

Description of the wash cycle

Max

temp.

(°C)

Max.

speed

(rpm)

Detergents

Max. load

(kg)

Cycle

duration

Pre-

wash

Wash

Fabric

softener

Normal

Eco

Time

Normal

Eco

Time

Daily

Cotton with prewash:

extremely soiled whites.

90° 1000

ll l

171

Cotton:

extremely soiled whites.

90° 1000

155

Cotton (1):

heavily soiled whites and resistant colours.

60° 1000

153

Cotton (2):

lightly soiled whites and delicate colours.

40° 1000

147

Cotton:

heavily soiled whites and resistant colours.

60° 1000

73,5130104

Coloured Cottons (3):

lightly soiled whites and delicate colours.

40° 1000

7 3,5 92 71

Synthetics:

heavily soiled resistant colours.

60° 800

3 2 85 72

Synthetics:

lightly soiled delicate colours.

40° 800

3 2 72 60

Special

Wool:

for wool, cashmere, etc.

40° 600

1,5

Silk/Curtains:

for garments in silk and viscose, lingerie.

30° 0

Jeans

40° 800

Express:

to refresh lightly soiled garments quickly (not suitable for

wool, silk and clothes which require washing by hand).

30° 800

1,5

Sport

Sport Intensive

30° 600

Sport Light

30° 600

Sport Shoes

30° 600

Max. 2

pairs

Partial wash cycles

Rinse

1000

- -

Spin

1000

- - -

Drain

- - -

Setting the temperature

Turn the TEMPERATURE knob to set the wash temperature (see Table of wash cycles).

The temperature may be lowered, or even set to a cold wash

The washing machine will automatically prevent you from selecting a temperature which is higher than the

maximum value set for each wash cycle.

Setting the spin speed

Turn the SPIN SPEED knob to set the spin speed for the selected wash cycle.

The maximum spin speeds available for each wash cycle are as follows:

Wash cycles Maximum spin speed

Cottons 1000 rpm

Synthetics 800 rpm

Wool 600 rpm

Silk drain only

The spin speed may be lowered, or the spin cycle can be excluded altogether by selecting the symbol

The washing machine will automatically prevent you from selecting a spin speed which is higher than the

maximum speed set for each wash cycle.

Functions

The various wash functions available with this washing machine will help to achieve the desired results, every time.

To activate the functions:

1. Press the button corresponding to the desired function;

2. the function is enabled when the corresponding indicator light is illuminated.

Note: If the indicator light flashes rapidly, this signals that this particular function may not be selected in

conjunction with the selected wash cycle.

Selecting this option enables you to suitably adjust drum rotation, temperature and water to a reduced load of

lightly soiled cotton and synthetic fabrics (refer to the

"Table of wash cycles"

).   enables you to wash in less

time thereby saving water and electricity. We suggest using a liquid detergent suitably measured out to the load

quantity.

 This function may not be used in conjunction with wash cycles 1, 2, 7, 8, 9, 10, 11, 12, 13, , , .

The function saves energy by not heating the water used to wash your laundry - an advantage both to

the environment and to your energy bill. Instead, intensified wash action and water optimisation ensure great wash

results in the same average time of a standard cycle.

For the best washing results we recommend the usage of a liquid detergent.

 This function may not be used in conjunction with wash cycles 1, 7, 8, 10, 11, 12, 13, , , .

Extra rinse

By selecting this option, the efficiency of the rinse is increased and optimal detergent removal is guaranteed. It is

particularly useful for sensitive skin.

 This function may not be used in conjunction with wash cycles 10, , .

Delay timer

This timer delays the start time of the wash cycle by up to 12 hours.

Press the button repeatedly until the indicator light corresponding to the desired delay time switches on. The fifth time

the button is pressed, the function will be disabled.

N.B. Once the START/PAUSE button has been pressed, the delay time can only be modified by decreasing it until launching

the set programme.

 This option is enabled with all programmes.

Personalisation

Detergents and laundry

Detergent dispenser drawer

Good washing results also depend on the correct

dose of detergent: adding too much detergent will not

necessarily result in a more efficient wash, and may in

fact cause build up on the inside of your appliance

and contribute to environmental pollution.

 Do not use hand washing detergents because these

create too much foam.

Open the detergent

dispenser drawer and

pour in the detergent or

washing additive, as

follows.

ompartment 1: Pre-wash detergent (powder)

compartment 2: Detergent for the wash cycle

(powder or liquid)

Liquid detergent should only be poured in immediately

prior to the start of the wash cycle.

compartment 3: Additives (fabric softeners, etc.)

The fabric softener should not overflow the grid.

Preparing the laundry

 Divide the laundry according to:

- the type of fabric/the symbol on the label

- the colours: separate coloured garments from

whites.

 Empty all garment pockets and check the buttons.

 Do not exceed the listed values, which refer to the

weight of the laundry when dry:

Durable fabrics: max. 7 kg

Synthetic fabrics: max. 3 kg

Delicate fabrics: max. 2 kg

Wool: max. 1,5 kg

Silk: max. 1 kg

How much does your laundry weigh?

1 sheet 400-500 g

1 pillow case 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1200 g

1 towel 150-250 g

Garments requiring special care

Wool: all wool garments can be washed using

programme 7, even those carrying the "hand-wash

only"

label. For best results, use special

detergents and do not exceed 1,5 kg of laundry.

Silk: use special wash cycle 8 to wash all silk

garments. We recommend the use of special

detergent which has been designed to wash delicate

clothes.

Curtains: fold curtains and place them in a pillow

case or mesh bag. Use wash cycle 8.

Jeans: Turn garments inside-out before washing and

use a liquid detergent. Use programme 9.

Load balancing system

Before every spin cycle, to avoid excessive vibrations

and to distribute the load in a uniform manner, the

drum rotates continuously at a speed which is slightly

greater than the washing rotation speed. If, after

several attempts, the load is not balanced correctly,

the machine spins at a reduced spin speed. If the

load is excessively unbalanced, the washing machine

performs the distribution process instead of spinning.

To encourage improved load distribution and balance,

we recommend small and large garments are mixed

in the load.

Precautions and tips

 This washing machine was designed and

constructed in accordance with international safety

regulations. The following information is provided for

safety reasons and must therefore be read carefully.

General safety

 This appliance was designed for domestic use only.

 This appliance is not intended for use by persons

(including children) with reduced physical, sensory

or mental capabilities, or lack of experience and

knowledge, unless they have been given

supervision or instruction concerning use of the

appliance by a person responsible for their safety.

Children should be supervised to ensure that they

do not play with the appliance.

 The washing machine must only be used by adults, in

accordance with the instructions provided in this manual.

 Do not touch the machine when barefoot or with

wet or damp hands or feet.

 Do not pull on the power supply cable when

unplugging the appliance from the electricity

socket. Hold the plug and pull.

 Do not open the detergent dispenser drawer while

the machine is in operation.

 Do not touch the drained water as it may reach

extremely high temperatures.

 Never force the porthole door. This could damage

the safety lock mechanism designed to prevent

accidental opening.

 If the appliance breaks down, do not under any

circumstances access the internal mechanisms in

an attempt to repair it yourself.

 Always keep children well away from the appliance

while it is operating.

 The door can become quite hot during the wash cycle.

 If the appliance has to be moved, work in a group

of two or three people and handle it with the utmost

care. Never try to do this alone, because the

appliance is very heavy.

 Before loading laundry into the washing machine,

make sure the drum is empty.

Disposal

 Disposing of the packaging materials: observe local

regulations so that the packaging may be re-used.

 The European Directive 2002/96/EC on Waste

Electrical and Electronic Equipment, requires that

old household electrical appliances must not be

disposed of in the normal unsorted municipal waste

stream. Old appliances must be collected

separately in order to optimise the recovery and

recycling of the materials they contain and reduce

the impact on human health and the environment.

The crossed out "wheeled bin" symbol on the

product reminds you of your obligation, that when

you dispose of the appliance it must be separately

collected.

Consumers should contact their local authority or

retailer for information concerning the correct

disposal of their old appliance.

Care and maintenance

Cutting off the water and electricity

supplies

 Turn off the water tap after every wash cycle. This

will limit wear on the hydraulic system inside the

washing machine and help to prevent leaks.

 Unplug the washing machine when cleaning it and

during all maintenance work.

Cleaning the washing machine

The outer parts and rubber components of the

appliance can be cleaned using a soft cloth soaked

in lukewarm soapy water. Do not use solvents or

abrasives.

Cleaning the detergent dispenser

drawer

Remove the dispenser

by raising it and pulling it

out (see figure).

Wash it under running

water; this operation

should be repeated

frequently.

Caring for the door and drum of your

appliance

 Always leave the porthole door ajar in order to

prevent unpleasant odours from forming.

Cleaning the pump

The washing machine is fitted with a self-cleaning

pump which does not require any maintenance.

Sometimes, small items (such as coins or buttons)

may fall into the pre-chamber which protects the

pump, situated in its bottom part.

 Make sure the wash cycle has finished and unplug

the appliance.

To access the pre-chamber:

1. using a screwdriver,

remove the cover panel

on the lower front part of

the washing machine

(see figure);

2. unscrew the lid by

rotating it anti-clockwise

(see figure): a little water

may trickle out. This is

perfectly normal;

3. clean the inside thoroughly;

4. screw the lid back on;

5. reposition the panel, making sure the hooks are

securely in place before you push it onto the

appliance.

Checking the water inlet hose

Check the inlet hose at least once a year. If there are

any cracks, it should be replaced immediately: during

the wash cycles, water pressure is very strong and a

cracked hose could easily split open.

 Never use second-hand hoses.

Troubleshooting

Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see Assistance),

make sure that the problem cannot be not solved easily using the following list.

Problem:

The washing machine does not

switch on.

The wash cycle does not start.

The washing machine does not

take in water (the indicator light

for the first wash cycle stage

flashes rapidly).

The washing machine

continuously takes in and drains

water.

The washing machine does not

drain or spin.

The washing machine vibrates a

lot during the spin cycle.

The washing machine leaks.

The "Functions" indicator lights

and the "start/pause" indicator

light flash, while one of the "phase

in progress" indicator lights and

the "door locked" indicator light

will remain lit in a fixed manner.

There is too much foam.

Possible causes / Solutions:

 The appliance is not plugged into the socket fully, or is not making contact.

 There is no power in the house.

 The washing machine door is not closed properly.

 The ON/OFF button has not been pressed.

 The START/PAUSE button has not been pressed.

 The water tap has not been opened.

 A delayed start has been set (see Personalisation).

 The water inlet hose is not connected to the tap.

 The hose is bent.

 The water tap has not been opened.

 There is no water supply in the house.

 The pressure is too low.

 The START/PAUSE button has not been pressed.

 The drain hose is not fitted at a height between 65 and 100 cm from

the floor (see Installation).

 The free end of the hose is under water (see Installation).

 The wall drainage system is not fitted with a breather pipe.

If the problem persists even after these checks, turn off the water tap,

switch the appliance off and contact the Assistance Service. If the

dwelling is on one of the upper floors of a building, there may be problems

relating to water drainage, causing the washing machine to fill with water

and drain continuously. Special anti-draining valves are available in shops

and help to avoid this inconvenience.

 The wash cycle does not include draining: some wash cycles require

the drain phase to be started manually.

 The drain hose is bent (see Installation).

 The drainage duct is clogged.

 The drum was not unlocked correctly during installation (see Installation).

 The washing machine is not level (see Installation).

 The washing machine is trapped between cabinets and walls (see Installation).

 The water inlet hose is not screwed on properly (see Installation).

 The detergent dispenser drawer is blocked (for cleaning instructions, see

Care and maintenance).

 The drain hose is not fixed properly (see Installation).

 Switch off the machine and unplug it, wait for approximately 1 minute

and then switch it back on again.

If the problem persists, contact the Technical Assistance Service.

 The detergent is not suitable for machine washing (it should display the

text for washing machines or hand and machine wash, or the like).

 Too much detergent was used.

Service

Before calling for Assistance:

 Check whether you can solve the problem alone (see Troubleshooting);

 Restart the programme to check whether the problem has been solved;

 If this is not the case, contact an authorised Technical Assistance Centre using the telephone number

provided on the guarantee certificate.

 Always request the assistance of authorised technicians.

Have the following information to hand:

 the type of problem;

 the appliance model (Mod.);

 the serial number (S/N).

This information can be found on the data plate applied to the rear of the washing machine, and can also

be found on the front of the appliance by opening the door.

!

Slovensky

Obsah

Intalácia, 14-15

Rozbalenie a vyrovnanie do vodorovnej polohy

Pripojenie kelektrickej akvodovodnej sieti

Prvý prací cyklus

Technické údaje

Popis práèky azahájenie pracieho

programu, 16-17

Ovládací panel

Kontrolky

Zahájenie pracieho programu

Pracie programy, 18

Tabu¾ka pracích programov

Uívate¾ské nastavenia, 19

Nastavenie teploty

Nastavenie odstreïovania

Funkcie

Pracie prostriedky a prádlo, 20

Dávkovaè pracích prostriedkov

Príprava prádla

Prádlo vyadujúce osobitnú starostlivos

Systém automatického vyváenia náplne

Opatrenia a rady, 21

Základné bezpeènostné pokyny

Likvidácia

Údrba a starostlivos, 22

Uzavretie prívodu vody a vypnutie elektrického

napájania

Èistenie práèky

Èistenie dávkovaèa pracích prostriedkov

Starostlivos odvierka a bubon

Èistenie èerpadla

Skontrolujte prítokovú hadicu vodu

Poruchy a spôsob ich odstránenia, 23

Servisná sluba, 24

IWC 7105

Návod na pouitie

PRÁÈKA

"

Intalácia

! Je ve¾mi dôleité uschova tento návod kvôli

prípadnému ïaliemu pouitiu. Vprípade predaja,

darovania alebo presahovania práèky sa uistite, e

zostane uloený vjej blízkosti, aby mohol poslúi

novému majite¾ovi pri oboznámení sa sèinnosou a

spríslunými upozorneniami.

! Pozorne si preèítajte uvedené pokyny: obsahujú

dôleité informácie, týkajúce sa intalácie, pouitia

a bezpeènosti pri práci.

Rozbalenie a vyrovnanie do vodorovnej

polohy

Rozbalenie

1. Rozba¾te práèku.

2. Skontrolujte, èi poèas prepravy nedolo kjej

pokodeniu. Vprípade, e je pokodená,

nezapájajte ju a obráte sa na predajcu.

3. Odstráòte 4 skrutky

slúiace na ochranu

poèas prepravy

agumovú podloku

sprísluným ditanèným

èlenom, ktoré sa

nachádzajú vzadnej

èasti (viï obrázok).

4. Uzatvorte otvory po skrutkách plastovými

krytkami z prísluenstva.

5. Uschovajte vetky diely: vprípade opätovnej

prepravy práèky ich bude potrebné opätovne

namontova.

! Obaly nie sú hraèky pre deti!

Vyrovnanie do vodorovnej polohy

1. Práèku je potrebné umiestni na rovnú a pevnú

podlahu tak, aby nebola opretá ostenu, nábytok

alebo onieèo iné.

2. Vprípade, e podlaha

nie je dokonale

vodorovná, môu by

prípadné rozdiely

vykompenzované

skrutkovaním predných

noièiek (viï obrázok);

Uhol sklonu, nameraný

na pracovnej ploche,

nesmie presiahnu 2°.

Dokonalé vyrovnanie do vodorovnej polohy zabezpeèí

stabilitu zariadenia a zamedzí vzniku vibrácií a hluku

poèas èinnosti. Vprípade intalácie na podlahovú

krytinu alebo na koberec, nastavte noièky tak, aby

pod práèkou zostal dostatoèný vo¾ný priestor na

ventiláciu.

Pripojenie kelektrickej akvodovodnej sieti

Pripojenie prítokovej hadice vody

1. Pripojte prívodnú

hadicu jej

zaskrutkovaním ku

kohútiku so studenou

vody shrdlom so závitom

3/4 (viï obrázok).

Pred pripojením hadice

nechajte vodu odtiec, a

kým nebude èíra.

2. Pripojte prítokovú

hadicu kpraèke, jej

zaskrutkovaním k

príslunej prípojke na

vodu, umiestnenej vpravo

hore (viï obrázok).

3. Zabezpeète, aby hadica nebola príli ohnutá alebo

stlaèená.

! Tlak vrozvode vody sa musí pohybova vrozmedzí

hodnôt uvedených vtabu¾ke s technickými údajmi

(viï ved¾ajia strana).

! Vprípade, e dåka prítokovej hadice nebude

dostatoèná, obráte sa na pecializovanú predajòu

alebo na autorizovaný technický personál.

! Nikdy nepouívajte u pouité hadice.

! Pouívajte hadice zprísluenstva zariadenia.

#

Technické údaje

Model

IWC 7105

Rozmery

írka 59,5 cm

výka 85 cm

håbka 53,5 cm

Kapacita

od 1 do 7 kg

Elektrické zapojenie

viï títok s technickými údajmi,

aplikovaný na zariadení

Pripojenie k rozvodu

vody

maximálny tlak 1 MPa (10 bar)

maximálny tlak 0,05 MPa (0.5 bar)

kapacita bubna 52 litrov

Rýchlos±z

odstreïovania

a±z do 1000 otáèok za minútu

Kontrolný program

pod¾a normy

EN 60456

program 2; teplota 6

0°

°°°°°°

;

náplò 7 kg prádla.

Toto zariadenie je v zhode s

nasledujúcimi smernicami Európskej únie:

- 2004/108/CE (Elektromagnetická

kompatibilita)

- 2002/96/CE

- 2006/95/CE (Nízke napätie)

Hluènost¡

(dB(A) re 1 pW)

Pranie: 58

Odstreïovanie: 76

65 - 100 cm

Pripojenie vypúacej hadice

Pripojte vypúaciu

hadicu, bez toho aby ste

ju ohli, kodpadovému

potrubiu alebo kodpadu

v stene, ktorý sa

nachádza od 65 do 100

cm nad zemou;

alebo ju uchyte k

okraju umývadla èi vane,

a pripevnite vodiaci

driak zprísluenstva

ku kohútu (viï

obrázok). Vo¾ný koniec

vypúacej hadice

nesmie zosta ponorený

do vody.

! Pouitie predlovacích hadíc sa neodporúèa; ak je

vak nevyhnutné, predlovacia hadica musí ma

rovnaký priemer ako originálna hadica a jej dåka

nesmie presiahnu 150 cm.

Pripojenie kelektrickej sieti

Pred zasunutím zástrèky do zásuvky sa uistite, e:

 zásuvka je uzemnená a e vyhovuje normám;

 zásuvka je schopná unies maximálnu záa

odpovedajúcu menovitému príkonu zariadenia,

uvedenému vtabu¾ke s technickými údajmi (viï

ved¾a);

 hodnota napájacieho napätia odpovedá údajom

uvedeným vtabu¾ke stechnickými údajmi (viï

ved¾a);

 zásuvka je kompatibilná so zástrèkou práèky.

Vopaènom prípade je potrebné vymeni zásuvku

alebo zástrèku.

! Práèka nesmie by umiestnená vonku  pod holým

nebom, a to ani vprípade, keby sa jednalo o miesto

chránené pred nepriazòou poèasia, pretoe je ve¾mi

nebezpeèné vystavi ju daïu a búrkam.

! Po ukonèení intalácie musí zásuvka zosta ¾ahko

prístupná.

! Nepouívajte predlovacie káble a rozvodky.

! Kábel nesmie by ohnutý alebo pritlaèený.

! Výmena kábla musí by zverená výhradne

autorizovanému technickému personálu.

Upozornenie! Výrobca neponesie iadnu

zodpovednos za následky spôsobené

nerepektovaním týchto pokynov.

Prvý prací cyklus

Po intalácii zariadenia je potrebné ete pred jeho

pouitím vykona jeden skúobný cyklus spracím

prostriedkom a bez náplne prádla, nastavením

pracieho programu 2.

$

Dávkovaè pracích prostriedkov: slúi na

dávkovanie pracích prostriedkov a prídavných

prostriedkov (viï Pracie prostriedky a prádlo).

Tlaèidlo ZAPNÚ/VYPNÚ: slúi na zapnutie

avypnutie práèky.

Otoèný ovládaè PROGRAMOV: pre nastavenie

pracích programov. Poèas pracieho programu zostane

vrovnakej polohe.

FUNKÈNÉ tlaèidlá s kontrolkami: Slúia navo¾bu

jednotlivých dostupných funkcií. Kontrolka zvolenej

funkcie zostane rozsvietená.

Otoèný ovládaè ODSTREÏOVANIA: slúi

nanastavenie odstreïovania alebo na jeho vylúèenie

(viï Uívate¾ské nastavenia).

Otoèný ovládaè TEPLOTY: slúi nanastavenie teploty

alebo prania alebo prania vstudenej vode (viï

Uívate¾ské nastavenia).

Kontrolky POSTUPU PRACIEHO CYKLU/

ONESKORENÉHO TARTU: slúia na kontrolu

postupu pracieho programu.

Rozsvietená kontrolka poukazuje na prebiehajúcu

fázu.

Ak je nastavená funkcia Oneskoreného tartu,

budú zobrazova èas zostávajúci do zahájenia

programu (viï ved¾ajia strana).

Kontrolka ZABLOKOVANIA DVIEROK: informuje

otom, èi je moné otvori dvierka (viï ved¾ajia

strana).

Tlaèidlo s kontrolkou TART/PAUZA: slúi na

zahájenie alebo na doèasné preruenie programov.

POZN.: Stlaèenie tohoto tlaèidla slúi na preruenie

prebiehajúceho prania; prísluná kontrolka bude

blika oranovým svetlom, zatia¾ èo kontrolka

prebiehajúcej fázy zostane rozsvietená stálym

svetlom. Keï bude kontrolka ZABLOKOVANIA

DVIEROK

zhasnutá, bude moné otvori dvierka.

Pre opätovné zahájenie prania zbodu, v ktorom bolo

preruené, opätovne stlaète toto tlaèidlo.

Pohotovostný reim

Po skoncení cyklu alebo vcase, ked nie je spustený

iaden cyklus, po 30 minútach dôjde kvypnutiu

zariadenia kvôli energetickej úspore. Na obnovenie

cinnosti zariadenia, nachádzajúceho sa

vpohotovostnom reime, stací stlacit tlacidlo

ZAPNÚ/VYPNÚ.

Popis práèky azahájenie

pracieho programu

Kontrolky

POSTUPU

PRACIEHO CYKLU/

ONESKORENÉHO TARTU

Kontrolka

ZABLOKOVANIA

DVIEROK

Tlaèidlo s

kontrolkou

TART/

PAUZA

Ovládací panel

Tlaèidlo

ZAPNÚ/VYPNÚ

FUNKÈNÉ

tlaèidlá s kontrolkami

Dávkovaè pracích

prostriedkov

Otoèný ovládaè

PROGRAMOV

Otoèný ovládaè

TEPLOTY

Otoèný ovládaè

ODSTREÏOVANIA

%

Kontrolky

Kontrolký sú zdrojom dôleitých informácií.

Informujú onasledujúcich skutoènostiach:

Oneskorený tart

Keï bola aktivovaná funkcia Oneskoreného tartu

(viï Uívate¾ské nastavenia), po zahájení pracieho

programu zaène blika prísluná kontrolka zvoleného

oneskorenia:

Priebene bude zobrazovaný èas zostávajúci do

tartu, a zobrazovanie bude sprevádzané blikaním

príslunej kontrolky:

Po uplynutí zvolenej doby oneskorenia dôjde

kzahájeniu nastaveného programu.

Kontrolky prebiehajúcej fázy

Po zvolení a zahájení poadovaného pracieho cyklu

dôjde kpostupnému rozsvecovaniu kontroliek

informujúcich o jeho postupe.

Funkèné tlaèidlá aprísluné kontrolky

Po zvolení konkrétnej funkcie dôjde k rozsvieteniu

príslunej kontrolky.

Keï zvolenú funkciu nie je moné zaradi do

nastaveného programu, prísluná kontrolka bude

blika, budete poèu akustický signál a funkcia nebude

aktivovaná.

Vprípade, e zvolená funkcia nie je kompatibilná

sinou predtým zvolenou funkciou, kontrolka prvej

volite¾nej funkcie bude blika a bude aktivovaná len

druhá, prièom kontrolka zvolenej funkcie sa rozsvieti

stálym svetlom.

Kontrolka zablokovania dvierok

Rozsvietenie tejto kontrolky signalizuje, e dvierka sú

zaistené kvôli zamedzeniu ich náhodnému otvoreniu;

aby sa dvierka nepokodili, pred ich otvorením je

potrebné vyèka, kým uvedená kontrolka nezhasne;

(vyèkajte pribline 3 minúty). Na otvorenie dvierok

vpriebehu pracieho cyklu stlaète tlaèidlo TART/

PAUZA; keï bude kontrolka ZAISTENÉ DVIERKA

zhasnutá, bude moné dvierka otvori.

Zahájenie pracieho programu

1. Zapnite práèku stlaèením tlaèidla ZAPNUTIE/VYPNUTIE. Vetky kontrolky sa rozsvietia na nieko¾ko sekúnd,

potom zhasnú a bude blika kontrolka TART/PAUZA.

2. Naplòte praèku a zatvorte dvierka.

3. Otoèným ovládaèom PROGRAMOV zvo¾te poadovaný prací program.

4. Nastavte teplotu prania (viï Uívate¾ské nastavenia).

5. Nastavte rýchlos odstreïovania (viï Uívate¾ské nastavenia).

6. slúi na dávkovanie pracieho prostriedku a prídavných prostriedkov (viï Pracie prostriedky a prádlo).

7. Zvo¾te poadované funkcie.

8. Zahájte prací program stlaèením tlaèidla TART/PAUZA a prísluná kontrolka zostane rozsvietená stálym svetlom

zelenej farby. Zruenie nastaveného pracieho cyklu sa vykonáva preruením èinnosti zariadenia stlaèením tlaèidla

TART/PAUZA a vo¾bou nového cyklu.

9. Po ukonèení pracieho programu sa rozsvieti kontrolka

. Po zhasnutí kontrolky ZABLOKOVANIA DVIEROK

bude moné dvierka otvori. Vytiahnite prádlo a nechajte dvierka pootvorené, aby bolo umonené vysuenie bubna.

Zapnite práèku stlaèením tlaèidla ZAPNUTIE/VYPNUTIE.

Pranie

Plákanie

Odstreïovanie

Odèerpanie vody

Ukonèenie prania

&

peciálne programy

Express (program 10) bol navrhnutý na pranie ¾ahko zneèisteného prádla vpriebehu krátkej doby: trvá len 15

minút a etrí tak energiu aj èas. Nastavením programu (10 pri 30°C) je moné pra spolu prádlo z tkanín

rôzneho druhu (s výnimkou vlny a hodvábu) smaximálnou náplòou 1,5 kg.

Sport Intensive (program 11) bol navrhnutý pre pranie ve¾mi zneèistených látok portového obleèenia

(teplákové súpravy, ortky apod.); pre dosiahnutie optimálnych výsledkov sa odporúèa neprekraèova maximálnu

náplò uvedenú v Tabu¾ka pracích programov.

Sport Light (program 12) bol navrhnutý pre pranie málo zneèistených látok portového obleèenia (teplákové

súpravy, ortky apod.); pre dosiahnutie optimálnych výsledkov sa odporúèa neprekraèova maximálnu náplò

uvedenú v Tabu¾ka pracích programov. Odporúèa sa poui tekutý prací prostriedok a poui dávku vhodnú pre

poloviènú náplò.

Sport Shoes (program 13) bol navrhnutý pre pranie portovej obuvi; pre dosiahnutie optimálnych výsledkov

neperte viac ako 2 páry naraz.

Pracie programy

Údaje uvedené vtabu¾ke majú len informatívny charakter.

Pre vetky Test Institutes:

1) Kontrolný program pod¾a normy EN 60456: nastavte program 2 steplotou 60°C.

2) Dlhý program na pranie bavlny: nastavte program 2 steplotou 40°C.

3) Krátky program na pranie bavlny: nastavte program 4 steplotou 40°C.

Pracie programy

Tabu¾ka pracích programov

Popis programu

Max.

Teplo-

(°C)

Max.

rýchlost

(otácky za

minútu)

Pracie prostriedky

Max. nápln

(kg)

Doba

trvania

cyklu

Pred-

pranie

Pranie Avivaz Bezna

Eco

Time

Bezna

Eco

Time

Programy pre kazdodenné pranie



BAVLNA + PREDPRANIE:

Mimoriadne pinavé biele prádlo.

90° 1000

ll l

171

BAVLNA:

Mimoriadne pinavé biele prádlo.

90° 1000

155

BAVLNA (1):

Znacne pinavé biele a farebné prádlo z odolných tkanín.

60° 1000

153

BAVLNA (2):

Málo pinavé biele chúlostivé prádlo.

40° 1000

147

BAVLNA:

Znacne pinavé biele a farebné prádlo z odolných tkanín.

60° 1000

73,5130104

FAREBNÁ BAVLNA (3):

Málo pinavé biele chúlostivé prádlo.

40° 800

7 3,5 92 71

SYNTETIKA:

Vel'mi pinavé farebné prádlo z odolných tkanín.

60° 800

3 2 85 72

SYNTETIKA:

Ciastocne pinavé farebné prádlo z odolných tkanín.

40° 800

3 2 72 60

peciálne programy

VLNA:

Pre vlnu, kamír, atd.

40° 600

1,5

HODVÁB/ZÁCLONY:

Pre prádlo z hodvábu, viskózy, spodné prádlo.

30° 0

JEANS

40° 800



EXPRESS:

Krýchlemu oziveniu ¾ahko zneèisteného prádla (nedoporuèuje sa pre

vlnu, hodváb a prádlo urèené na pranie v rukách).

30° 800

1,5

Sport



Sport Intensive

30° 600



Sport Light

30° 600

!

Sport Shoes

30° 600

(

Max.

2 páry.)

Dielcie programy

Plákanie

1000

- -

Odstred'ovanie

1000

- - -

Odcerpanie vody

- - -









'

Nastavenie teploty

Otáèaním otoèného ovládaèa TEPLOTY sa nastavuje teplota prania (viï Tabu¾ka programov).

Teplota môe by postupne zniovaná a po pranie v studenej vode (

Zariadenie automaticky zabráni nastaveniu vyej teploty ako je maximálna teplota pre kadý prací program.

Nastavenie odstreïovania

Otáèaním otoèného ovládaèa ODSTREÏOVANIA sa nastavuje rýchlos odstreïovania zvoleného pracieho

programu.

Maximálne rýchlosti pre jednotlivé pracie programy sú:

Pracie programy Maximálna rýchlos

Bavlna 1000 otáèok za minútu

Syntetické tkaniny 800 otáèok za minútu

Vlna 600 otáèok za minútu

Hodváb len odèerpanie vody

Rýchlos odstreïovania môe by zníená, alebo odstreïovanie môe by vylúèené vo¾bou symbolu

Zariadenie automaticky zabráni nastaveniu vyej rýchlosti odstreïovania ako je maximálna rýchlos pre kadý

prací program.

Funkcie

Jednotlivé funkcie, ktorými práèka disponuje, umoòujú dosiahnu poadovaný stupeò èistoty a belosti praného

prádla. Spôsob aktivácie jednotlivých funkcií:

1. stlaète prísluné tlaèidlo poadovanej funkcie;

2. rozsvietenie príslunej kontrolky signalizuje, e dolo kaktivácii zvolenej funkcie.

Poznámka: Rýchle blikanie kontrolky signalizuje, e prísluná funkcia je nepouite¾ná poèas nastaveného

pracieho programu.

Vo¾bou tejto funkcie budú mechanický pohon, teplota a voda nastavené pre zníenú náplò málo zneèistenej

bavlny a syntetických materiálov (viï Tabu¾ka programov). Pri pouití programu 

 môete pracova

skratími dobami a uetri vodu a energiu. Odporúèa sa pouíva dávku tekutého pracieho prostriedku, vhodnú

pre naplnené mnostvo.

! Táto funkcia nie je pouite¾ná pri programoch 1, 2, 7, 8, 9, 10, 11, 12, 13, , , .

Funkcia prispieva kenergetickej úspore, tým e neohrieva vodu pouitú na pranie prádla  etrí sa tým

nie len ivotné prostredie, ale aj náklady za elektrickú energiu. Posilnený úèinok a optimalizovaná spotreba

vody skutoène zabezpeèia optimálny výsledok za rovnakú priemernú dobu odpovedajúcu tandardnému cyklu.

Na dosiahnutie lepích výsledkov prania sa odporúèa poui tekutý prací prostriedok.

 Táto funkcia nie je pouite¾ná pri programoch 1, 7, 8, 10, 11, 12, 13, , , .

Extra Plákanie

Vo¾bou tejto funkcie sa zvýi úèinnos plákania a zaistí sa maximálny stupeò odstránenia pracieho prostriedku.

Je uitoèná hlavne pre mimoriadne citlivé pokoky.

! Táto funkcia nie je pouite¾ná pri programoch 10, , .

Oneskorený tart

Slúi naodloenie zahájenia pracieho cyklu a o 12 hodín.

Opakovane stláèajte tlaèidlo, a kým sa nerozsvieti kontrolka oznaèujúca poadovanú dobu oneskorenia.

Po piatom stlaèení tlaèidla dôjde kzrueniu uvedenej funkcie.

POZN.: Po stlaèení tlaèidla TART/PAUZA je moné zmeni èas oneskorenia len jeho zníením a to a do zahájenia

nastaveného programu.

! Je aktívny pri vetkých pracích programoch.

Uívate¾ské nastavenia



Pracie prostriedky a prádlo

Dávkovaè pracích prostriedkov

Dobrý výsledok prania závisí aj od správneho

dávkovania pracieho prostriedku: pouitie nadmerného

mnostva zniuje efektivitu prania a napomáha tvorbe

vodného kameòa na vnútorných èastiach práèky a

zvyuje zneèistenie ivotného prostredia.

 Nepouívajte pracie prostriedky urèené na pranie v

rukách, pretoe spôsobujú tvorbu nadmerného

mnostva peny.

Pri vyahovaní dávkovaèa

pracích prostriedkov a pri

jeho plnení pracími alebo

prídavnými prostriedkami

postupujte nasledovne.

priehradka 1: Prací prostriedok na predpieranie

(prákový)

priehradka 2: Prací prostriedok na pranie

(prákový alebo tekutý)

Tekutý prací prostriedok sa nalieva len tesne pred

zahájením pracieho cyklu.

priehradka 3: Prídavné prostriedky (avivá, atï.)

Avivá nesmie vyteka zmrieky.

Príprava prádla

 Roztrieïte prádlo pod¾a:

- druhu tkaniny / symbolu na visaèke.

- farby: odde¾te farebné prádlo od bieleho.

 Vyprázdnite vrecká a skontrolujte gombíky.

 Neprekraèujte povolenú náplò, vzahujúcu sa na

hmotnos suchého prádla:

Odolné tkaniny: max. 7 kg

Syntetické tkaniny: max. 3 kg

Chúlostivé tkaniny: max. 2 kg

Vlna: max. 1,5 kg

Hodváb: max. 1 kg

Ko¾ko vái prádlo?

1 plachta 400-500 g

1 oblieèka 150-200 g

1 obrus 400-500 g

1 upan 900-1.200 g

1 uterák 150-250 g

Prádlo vyadujúce osobitnú starostlivos

Vlna: Sprogramom 7 je moné pra vpráèke vetky

druhy vlneného prádla, aj tie, ktoré sú oznaèené

visaèkou pra len v rukách

. Pre dosiahnutie

optimálnych výsledkov pouívajte pecifický prací

prostriedok aneprekraèujte náplò 1,5 kg.

Hodváb: pouite prísluný program 8 na pranie

vetkého prádla z hodvábu. Odporúèa sa pouitie

pracieho prostriedku pre chúlostivé prádlo.

Záclony: odporúèa sa ich posklada avloi do

sáèku dodaného vrámci prísluenstva. Pouite

program 8.

Jeans: Prevráte prádlo naruby a pouite tekutý

prací prostriedok. Pouite program 9.

Systém automatického vyváenia náplne

Pred kadým odstreïovaním bubon vykoná otáèanie

rýchlosou o málo prevyujúcou rýchlos prania, aby

sa tak odstránili vibrácie aaby sa náplò rovnomerne

rozloila. Vprípade, e po nieko¾ko násobných

pokusoch o vyváenie prádlo ete nebude správne

vyváené, zariadenie vykoná odstreïovanie niou

rýchlosou, ako je prednastavená rýchlos. Ak je

práèka nadmerne nevyváená, vykoná namiesto

odstreïovania vyváenie. Za úèelom dosiahnutia

rovnomernejieho rozloenia náplne a jej správneho

vyváenia, odporúèa sa pomiea ve¾ké a malé kusy

prádla.

Stránka sa načítava ...

Indesit IWC 7105 ECO (EE) Užívateľská príručka

Značka: Indesit

Model: IWC 7105 ECO (EE)

Kategória: Práčky

Typ: Užívateľská príručka

Stiahnite si PDF

správa

V iných jazykoch

italiano: Indesit IWC 7105 ECO (EE) Guida utente
polski: Indesit IWC 7105 ECO (EE) instrukcja
română: Indesit IWC 7105 ECO (EE) Manualul utilizatorului