Hikoki C8FSHE Slide Compound Miter Saw Návod na používanie

Značka: Hikoki

Model: C8FSHE Slide Compound Miter Saw

Kategória: Elektrické náradie

Typ: Návod na používanie



฀

Slide Compound Miter Saw

Paneelsäge

º·ÏÙÛÔÎﬁÙË˜-P¿vÙÈ¿Ï

Pilarka

Gérvágó

Pokosová pila

Raylı gönye kesme

Fierăstrău pentru tăieri înclinate

Potezna krožna žaga

TopáoÇoäÌaÓ ÔËÎa c ÔapaÎÎeÎëÌêÏË

ÌaÔpaÇÎÓïçÏÏË

Read through carefully and understand these instructions before use.

Diese Anleitung vor Benutzung des Werkzeugs sorgfältig durchlesen und verstehen.

¢È·‚¿ÛÙÂ ÚÔÛÂÎÙÈÎ¿ Î·È Î·Ù·ÓÔ‹ÛÂÙÂ ·˘Ù¤˜ ÙÈ˜ Ô‰ËÁ›Â˜ ÚÈÓ ÙË ¯Ú‹ÛË.

Przed użytkowaniem należy dokładnie przeczytać niniejszą instrukcję i zrozumieć jej treść.

Használat előtt olvassa el figyelmesen a használati utasítást.

Před použitím si pečlivě přečtěte tento návod a ujistěte se, že mu dobře rozumíte.

Aleti kullanmadan önce bu kılavuzu iyice okuyun ve talimatları anlayın.

Înainte de utilizare, citiţi cu atenţie și înţelegeţi prezentele instrucţiuni.

Pred uporabo natančno preberite in razumite ta navodila.

BÌËÏaÚeÎëÌo ÔpoäÚËÚe ÀaÌÌyï ËÌcÚpyÍáËï Ôo íÍcÔÎyaÚaáËË ÔpeÊÀe äeÏ ÔoÎëÁoÇaÚëcÓ ËÌcÚpyÏeÌÚoÏ.

Handling instructions

Bedienungsanleitung

√‰ËÁ›Â˜ ¯ÂÈÚÈÛÌÔ‡

Instrukcja obsługi

Kezelési utasítás

Návod k obsluze

Kullanım talimatları

Instrucţiuni de utilizare

Navodila za rokovanje

àÌcÚpyÍáËÓ Ôo íÍcÔÎyaÚaáËË

C 8FSHE • C 8FSE

C8FSHE

ÅÁ¿ÅÂº¿Ä½ÉÅƔƑÊºƔ

ﬃ

ěč

ř ě

č č

ş ğ

Ελληνικά ă

ΔΗΛΩΣΗ ΕΝΑΡΜΟΝΙΣΜΟΥ

Δηλώνουμε με αποκλειστική μας ευθύνη ότι οΦαλτσοκόπτης Ράντιαλ

οοποίος προσδιορίζεται από τον τύπο και ειδικό αναγνωριστικό κωδικό

είναι σύμφωνος με όλες τις σχετικές απαιτήσεις των Οδηγιών και

με τα σχετικά πρότυπα Τεχνικό Αρχείο στο Δείτε παρακάτω

Ο Διαχειριστής Ευρωπαϊκών Προτύπων στο γραφείο

εκπροσώπησης στην Ευρώπη είναι εξουσιοδοτημένος για τη

σύνταξη του τεχνικού φακέλου

Η δήλωση ισχύει μόνο για το προϊόν που είναι τοποθετημένη

σήμανση

ă ă ă ă ă ă

ă ș ţ ș

șţ

ă ă

ţ ă

ś ł ą łą ą ść ż

ł ś ż

ż ą

čč

č č

Русский

ДЕКЛАРАЦИЯ СООТВЕТСТВИЯ

Мы с полной ответственностью заявляем что торцовочная пила

с параллельными направляющими идентифицируемая по типу

и соответствующему идентификационному коду отвечает

всем соответствующим требованиям директив и стандартов

Техническая документация в см ниже

Менеджер по европейским стандартам в представительстве в

Европе уполномочен составлять техническую документацию

Данная декларация относится к изделиям на которых имеется

маркировка

ﬃ



฀

[

]

n n m

ÅÁ¿ÅÂº¿Ä½ÉÅƔƑÊºƔ

ﬃ

ěč

ř ě

č č

ş ğ

Ελληνικά ă

ΔΗΛΩΣΗ ΕΝΑΡΜΟΝΙΣΜΟΥ

Δηλώνουμε με αποκλειστική μας ευθύνη ότι οΦαλτσοκόπτης Ράντιαλ

οοποίος προσδιορίζεται από τον τύπο και ειδικό αναγνωριστικό κωδικό

είναι σύμφωνος με όλες τις σχετικές απαιτήσεις των Οδηγιών και

με τα σχετικά πρότυπα Τεχνικό Αρχείο στο Δείτε παρακάτω

Ο Διαχειριστής Ευρωπαϊκών Προτύπων στο γραφείο

εκπροσώπησης στην Ευρώπη είναι εξουσιοδοτημένος για τη

σύνταξη του τεχνικού φακέλου

Η δήλωση ισχύει μόνο για το προϊόν που είναι τοποθετημένη

σήμανση

ă ă ă ă ă ă

ă ș ţ ș

șţ

ă ă

ţ ă

ś ł ą łą ą ść ż

ł ś ż

ż ą

čč

č č

Русский

ДЕКЛАРАЦИЯ СООТВЕТСТВИЯ

Мы с полной ответственностью заявляем что торцовочная пила

с параллельными направляющими идентифицируемая по типу

и соответствующему идентификационному коду отвечает

всем соответствующим требованиям директив и стандартов

Техническая документация в см ниже

Менеджер по европейским стандартам в представительстве в

Европе уполномочен составлять техническую документацию

Данная декларация относится к изделиям на которых имеется

маркировка

ﬃ

910

11 12

14 15

µµ

IndustrieZentrum NÖ –Süd, Straße 7, Obj. 58/A6 2355

Wiener Neudorf, Austria

Tel: +43 2236 64673/5

Fax: +43 2236 63373

URL: http://www.hikoki-powertools.at

1106 Bogáncsvirág u.5-7, Budapest, Hungary

Tel: +36 1 2643433

Fax: +36 1 2643429

URL: http://www.hikoki-powertools.hu

ul. Gierdziejewskiego 1

02-495 Warszawa, Poland

Tel: +48 22 863 33 78

Fax: +48 22 863 33 82

URL: http://www.hikoki-narzedzia.pl

Modřická 205, 664 48 Moravany, Czech Republic

Tel: +420 547 422 660

Fax: +420 547 213 588

URL: http://www.hikoki-powertools.cz

Kashirskoe Shosse 41, bldg. 2, 115409, Moscow, Russia

Tel: +7 495 727 4460

Fax: +7 495 727 4461

URL: http://www.hikoki-powertools.ru

Ring Road, No. 66, Mustang Traco Warehouses, Warehouse

No.1, Pantelimon City, 077145, Ilfov County, Romania

Tel: +40 371 135 109

Fax: +40 372 899 765

URL: http://www.hikoki-powertools.ro

910

16 17

18 19

20 21

22 23

{

}

{

IndustrieZentrum NÖ –Süd, Straße 7, Obj. 58/A6 2355

Wiener Neudorf, Austria

Tel: +43 2236 64673/5

Fax: +43 2236 63373

URL: http://www.hikoki-powertools.at

1106 Bogáncsvirág u.5-7, Budapest, Hungary

Tel: +36 1 2643433

Fax: +36 1 2643429

URL: http://www.hikoki-powertools.hu

ul. Gierdziejewskiego 1

02-495 Warszawa, Poland

Tel: +48 22 863 33 78

Fax: +48 22 863 33 82

URL: http://www.hikoki-narzedzia.pl

Modřická 205, 664 48 Moravany, Czech Republic

Tel: +420 547 422 660

Fax: +420 547 213 588

URL: http://www.hikoki-powertools.cz

Kashirskoe Shosse 41, bldg. 2, 115409, Moscow, Russia

Tel: +7 495 727 4460

Fax: +7 495 727 4461

URL: http://www.hikoki-powertools.ru

Ring Road, No. 66, Mustang Traco Warehouses, Warehouse

No.1, Pantelimon City, 077145, Ilfov County, Romania

Tel: +40 371 135 109

Fax: +40 372 899 765

URL: http://www.hikoki-powertools.ro

5 mm

12 mm

†

LMM

†

B§

English Deutsch Ελληνικά

1Handle Griff

2Lock Lever Sperrhebel

3Motor Head Motorkopf

4Gear Case Getriebegehäuse

5Motor Motor

6Dust Bag Staubbeutel

7Hing Scharnier

8Holder (A) Halter (A)

9Light (Only C8FSHE) Licht (Nur C8FSHE)

0Indicator (For bevel scale) Zeiger (Für Schrägschnittskala)

ALaser Marker (Only C8FSHE) Lasermarkierer (Nur C8FSHE)

BSaw Blade Sägeblatt

CVise Assembly Schraubstocksatz

DFence (B) Gitter (B)

ESub Fence Hilfsführung

FLever Hebel Μλς

GSide Handle Seitengriff

HTurntable Drehbühne

ITable Insert Tischeinsatz

JIndicator (For miter scale) Zeiger (Für Gehrungsskala)

KFence (A) Gitter (A)

LLower Guard Unterer Schutz

MWasher (D) Unterlegscheibe (D)

NSpindle Cover Spindelabdeckung

OSwitch (For laser marker) Schalter (Für Lasermarkierer)

(Only C8FSHE) (Nur C8FSHE)

PTrigger Switch Auslöserschalter

QSwitch (For light) (Only C8FSHE) Lichtschalter (Nur C8FSHE)

RMaking (Pre-marked) Markierung (vormarkiert)

SSpindle Lock Spindelhebel

T6 mm Flat Head Screw 6 mm Flachkopfschraube

UGuard Schutz

VBase Grundplatte

WHolder Halter

XSet Pin Fixierstift

YClamp Lever Klemmhebel

Z6 mm Depth Adjustment Bolt 6 mm Tiefenstellschraube

[Slide Securing Knob Führungssicherungsknopf

\Adjuster (For laser marker) Einstellung (Für Lasermarkierer)

(Only C8FSHE) (Nur C8FSHE)

]Locking Pin Verriegelungsstift

`6 mm Bolt 6-mm-Schraube

aWorkpiece Werkstück

bAuxiliary Board Hilfsbrett

c8 mm Depth Adjustment Bolt 8-mm-Tiefeneinstellschraube

ερύλι

Μλς ασάλισης

Κεαλή Μτέρ

Θήκη Ταυτήτων

Μτέρ

Σακύλα Σκνης

Μεντεσές

Στήριγµα (A)

Λυνία (Μν στ C8FSHE)

∆είκτης (Για την κλίµακα κλίσης)

∆είκτης λέιερ

(Mvo yα τ C8FSHE)

Πρινωτή Λάµα

Συγκρτηµα Μέγγενης

δηγς (Β)

∆ευτερεύν δηγς

Πλευρικ ερύλι

Περιστρική Πλάκα

Τεµάι τρδσίας

∆είκτης (Για την κλίµακα λτµής)

δηγς (Α)

Κάτω πρυλακτήρας

Ρδέλα (D)

Κάλυµµα Άνα

∆ιακπτης (Για τ δείκτη λέιερ)

(Μν για τ C8FSHE)

Σκανδάλη ∆ιακπτης

∆ιακπτης (για τη λυνία) (Mvo

yα τ C8FSHE)

Σηµάδι (πρσηµειωµέν)

Ασάλεια Άνα

6 ιλ. Βίδα µε επίπεδη κεαλή

Πρυλακτήρας

Βάση

Στήριγµα

Περνη ρύθµισης

Μλς Σύσιης

6 ιλ. Μπυλνι ρύθµισης άθυς

Κυµπί αναστλής λίσθησης

Ρυθµιστής (Για τ δείκτη λέιερ)

(Mvo yα τ C8FSHE)

Περνη Ασαλείας

6 mm Μπυλνι

Αντικείµεν εργασίας

Βηθητικς πάγκς

Μπυλνι ρύθµισης άθυς 8 mm

English Deutsch Ελληνικά

d6 mm Nut 6 mm Schraubenmutter

6 mm Knob Bolt (Optional accessory)

Knopfschraube, 6 mm

(Sonderzubehör)

fHolder (Optional accessory) Halter (Sonderzubehör)

gSteel Square Stahlwinkel

6 mm Wing Nut (Optional accessory)

Flügelschraube, 6 mm

(Sonderzubehör)

iHeight Adjustment Bolt 6 mm Höheneinstellschraube, 6 mm

(Optional accessory) (Sonderzubehör)

jBase Surface Grundfläche

kStopper (Optional accessory) Anschlag (Sonderzubehör)

6 mm Knob Bolt (Optional accessory)

Knopfschraube, 6 mm

(Sonderzubehör)

mLine Linie

nWarning sign Warnzeichen

oScrew Holder Schraubenhalter

p6 mm Wing Bolt (B) 6-mm-Flügelschraube (B)

qVise Shaft Schraubstockachse

rLight lens Lichtlinse

sFence Gitter

t6 mm Wing Bolt (A) 6 mm-Flügelschraube (A)

uVise Plate Schraubstockbacke

vKnob Knopf

wLaser line Laserlinie

xGroove Nut

yBevel Scale Schrägschnittskala

zMiter Scale Gehrungsskala

Crown molding Vise Ass’y Schraubstocksatz für

{(Optional accessory) Kronenform (Sonderzubehör)

6 mm Wing Nut (Optional accessory)

Flügelmutter, 6 mm

(Sonderzubehör)

}Crown molding Stopper (L) Kronenformanschlag (L)

(Optional accessory) (Sonderzubehör)

~Crown molding Stopper (R) Kronenformanschlag (R)

(Optional accessory) (Sonderzubehör)

åCrown molding Kronenform

ç10 mm Box Wrench 10 mm Steckschüssel

†Bolt Schraube

¢Light Licht

£Wear limit line Verschleißgrenze

§Color (A) Farbe (A)

6 ιλ. παιµαδι

6 mm Φτερωτ µπυλνι

(Πραιρετικ εάρτηµα)

Στήριγµα (Πραιρετικ εάρτηµα)

Ατσαλένις Γνώµνας

6 mm Φτερωτ Παιµάδι

(Πραιρετικ εάρτηµα)

Μπυλνι Ρύθµισης Ύψυς

6 mm (Πραιρετικ εάρτηµα)

Επιάνεια Βάσης

Αναστλέας (Πραιρετικ εάρτηµα)

Μπυλνι-Κυµπί 6 mm

(Πραιρετικ εάρτηµα)

Γραµµή

Πρειδπιητικ σήµα

Στήριγµα Βίδας

6 mm Φτερωτ µπυλνι (Β)

Άνας µέγγενης

Φακς λυνίας

δηγς

6 mm Φτερωτ Μπυλνι (A)

Πλάκα Μέγγενης

Κυµπί

Γραµµή λέιερ

Αυλάκωση

Κλίµακα κλίσης

Κλίµακα Λτµής

Συγκρτηµα Μέγγενης για τη

∆ιαµρωση Κρνίας

(Πραιρετικ εάρτηµα)

6 mm Φτερωτ Παιµάδι

(Πραιρετικ εάρτηµα)

Αναστλέας ∆ιαµρωσης Κρνίας

(L) (Πραιρετικ εάρτηµα)

Αναστλέας ∆ιαµρωσης Κρνίας

(R) (Πραιρετικ εάρτηµα)

∆ιαµρωση Κρνίας

10 mm Κίλ Κλειδί

Μπυλνι

Λυνία

ρι θράς

ρώµα (Α)

Polski Magyar Čeština

1Rączka Markolat RukojeŅ

2Dźwignia blokady Rögzítőkar Blokovací páčka

3Głowica silnika Motorfej Hlava motoru

4Obudowa przekładni Hajtásház Převodová skříň

5Silnik Motor Motor

6Worek pyłowy Porzsák Sáček na prach

7Przegub Csuklós felfüggesztés Závěs

8Uchwyt (A) Tartó (A) Držák (A)

9Lampa (Tylko model C8FSHE)

Világítás (Csak a C8FSHE modell esetén)

Světlo (Pouze C8FSHE)

?Wskaźnik (Dla cięcia skośnego) Jelző (Ferde skála esetén) Indikátor (Pro stupnici úkosu)

AZnacznik laserowy (Tylko C8FSHE) Lézeres jelölő (Csak C8FSHE)

Laserový značkovač (Pouze C8FSHE)

BOstrze piły Fűrészlap Pilový kotouč

CImadło Satuszerelvény Sestava svěráku

DOgranicznik (B) Vezetőléc (B) Stavítko (B)

EPodogranicznik Alsó vezetőléc Menší stavítko

FDźwignia Kar Páčka

GRączka boczna Oldalsó markolat Boční rukojeŅ

HPodstawa obrotowa Forgatóasztal Otočný stůl

IWkładka stołowa Asztalbetét Vložka stolu

JWskaźnik Jelző Indikátor

(Dla skali uciosu) (Sarokillesztési skálához) (Pro stupnici pokosu)

KOgranicznik (A) Vezetőléc (A) Stavítko (A)

LOsłona dolna Alsó védőburkolat Spodní ochranný kryt

MPodkładka (D) Alátét (D) Podložka (D)

NPokrywa wrzeciona Tengelyfedél Kryt vřetena

OPrzełącznik (Dla znacznika Kapcsoló (Lézeres jelölőhöz) Vypínač (Pro laserový značkovač)

laserowego) (Tylko C8FSHE) (Csak C8FSHE) (Pouze C8FSHE)

PWyłącznik spustowy Indítókapcsoló Spouštěcí spínač

QWyłącznik (Lampy) Kapcsoló (Világítás) Vypínač (Světla) (Pouze C8FSHE)

(Tylko model C8FSHE) (Csak a C8FSHE modell esetén)

ROznakowanie Jelölés (előre megjelölt) Značka (předem vyznačeno)

(oznakowanie fabryczne)

SBlokada wrzeciona Tengelyrögzítő Blokování vřetena

TŚruba z łbem płaskim 6 mm 6 mm lapos fejű csavar

6 mm šroub s plochou zápustnou hlavou

UOsłona Védőlap Ochranný kryt

VPodstawa Alap Základová deska

WUchwyt Tartó Držák

XTrzpień ustalający Beállító csap Nastavovací kolík

YDźwignia zaciskowa Leszorító kar Páčka svorky

Śruba regulacji głębokości 6 mm

6 mm-es mélységállító csavar

6 mm šroub k nastavení hloubky

[Pokrętło blokujące prowadnicy Csúszkarögzítő gomb ZajišŅovací knoflík posunu

Element regulacyjny (Znacznika laserowego)

Állító (Lézetkészítőhöz) Seřizovač (Pro laserový značkovač)

(Tylko C8FSHE) (Csak C8FSHE) (Pouze C8FSHE)

]Kołek blokujący Rögzítőcsapszeg Blokovací kolík

`Śruba 6 mm 6 mm csavar 6 mm šroub

aPrzedmiot obrabiany Munkadarab Obrobek

bPłyta pomocnicza Kiegészítő lap Pomocná deska

cŚruba regulacji głębokości 8 mm 8 mm-es mélységállító csavar 8 mm šroub nastavení hloubky

Polski Magyar Čeština

dNakrętka 6 mm 6 mm-es anya 6 mm matice

eŚruba skrzydełkowa 6 mm 6 mm-es szárnyascsavar 6 mm křídlový šroub

(Akcesorium opcjonalne) (Opcionális tartozék) (Doplňkové příslušenství)

fUchwyt (Akcesorium opcjonalne) Tartó (Opcionális tartozék) Držák (Doplňkové příslušenství)

gKątownik stalowy Acél négyzet Ocelový úhelník

hNakrętka motylkowa 6 mm 6 mm-es szárnyas anya 6 mm křídlový šroub

(Akcesorium opcjonalne) (Opcionális tartozék) (Doplňkové příslušenství)

iŚruba regulacji wysokości 6 mm Magasságállító csavar 6 mm Šroub pro nastavení výšky 6 mm

(Akcesorium opcjonalne) (Opcionális tartozék) (Doplňkové příslušenství)

jPowierzchnia podstawy Alapfelület Povrch základové desky

kOgranicznik (Akcesorium opcjonalne) Megállító (Opcionális tartozék) Zarážka (Doplňkové příslušenství)

lŚruba gałkowa 6 mm 6 mm-es gombos csavar 6 mm šroub s knoflíkem

(akcesorium opcjonalne) (opcionális tartozék) (doplňkové příslušenství)

mLinia Vonal Linka

nZnak ostrzegawczy Figyelmeztető búgás Varovný štítek

oUchwyt śruby Csavartartó Držák šroubu

pŚruba skrzydełkowa 6 mm (B) 6 mm szárnyas csavar (B) 6 mm Křídlový šroub (B)

qWał imadła Satutengely Hřídel svěráku

rSzkiełko lampy Fényforrás lencséje Čočka světla

sOgranicznik Vezetőléc Stavítko

tŚruba skrzydełkowa 6 mm (A) 6 mm szárnyas csavar (A) 6 mm křídlový šroub (A)

uTabliczka imadła Satutábla Deska svěráku

vGałka Gomb Knoflík

wLinia lasera Lézervonal Linie laseru

xRowek Horony Drážka

ySkala cięcia skosśnego Ferde skála Stupnice úkosu

zSkala uciosu Sarokillesztési skála (előre jelölt) Stupnice pokosu

{Imadło do form wypukłych Koronás öntvény satuszerelvény Svěrák zvonovnicového článku

(Akcesorium opcjonalne) (Opcionális tartozék) (Doplňkové příslušenství)

|Nakrętka motylkowa 6 mm 6 mm-es szárnyas anya 6 mm křídlový šroub

(Akcesorium opcjonalne) (Opcionális tartozék) (Doplňkové příslušenství)

}Ogranicznik do form wypukłych (L) Koronás öntvény megállító (L) Zarážka zvonovnicového článku (L)

(Akcesorium opcjonalne) (Opcionális tartozék) (Doplňkové příslušenství)

~Ogranicznik do form wypukłych (R) Koronás öntvény megállító (R) Zarážka zvonovnicového článku (R)

(Akcesorium opcjonalne) (Opcionális tartozék) (Doplňkové příslušenství)

åForma wypukła Koronás öntvény Zvonovnicový článek

çKlucz nasadowy 10 mm 10 mm-es dugókulcs 10 mm nástrčný klíč

†Śruba Csavar Šroub

¢Lampa Világítás Světlo

£Linia dopuszczalnego zużycia Kopási határvonal Čára limitu opotřebení

§Kolor (A) Szín (A) Barva (A)

Türkçe

1Sap

2Kilit kolu

3Motor Baßlıåı

4Dißli kutusu

5Motor

6Toz Torbası

7Menteße

8Tutamaç (A)

9Lamba (Sadece C8FSHE)

?Gösterge (Eåim ölçeåi için)

ALazer Óßaretleyici (Sadece C8FSHE)

BTestere bıçaåı

CMengene Takımı

DSiper (B)

EAlt Siper

FKol

GYan Sap

HDöner Taban

IMasa Eklemesi

JGösterge (Íev ölçeåine göre)

KSiper (A)

LAlt Koruyucu

MRondela (D)

NMil kapaåı

OAnahtar (Lazer ißaretleyici için)

(Sadece C8FSHE)

PAçma/Kapama Anahtarı

QDüåme (Lamba için)

(Sadece C8FSHE)

RÓßaretleme (ön-ißaretli)

SKilit iånesi

T6 mm düz Baßlı Vida

UKoruyucu

VTaban/Alt kısım

WTutamaç

XAyar pimi

YMengene kolu

Z6 mm derinlik Ayar Cıvatası

[Sürgü sıkıßtırma tokmaåı (A)

\Ayarlayıcı (Lazer ißaretleyici için)

(Sadece C8FSHE)

]Kilit Óånesi

`6 mm Cıvata

aÓß parçası

bYardımcı Levha

c8 mm'lik Derinlik ayarlama cıvatası

d6 mm Somun

Română

Mâner

Manetă de blocare

Capul motorului

Carcasa motorului

Motor

Sac pentru praf

Balama

Suport (A)

Lampă (Numai C8FSHE)

Indicator (Pentru gradaţia înclinării)

Marcator cu laser (Numai C8FSHE)

Lama fierăstrăului

Ansamblu menghină

Element de limitare (B)

Element de limitare inferior

Manetă

Mâner lateral

Suprafaţă de lucru pivotantă

Inserţie pentru suprafaţa de lucru

Indicator (Pentru scala pentru tăiere înclinată)

Element de protecţie (A)

Apărătoare inferioară

Șaibă (D)

Carcasa axului

Comutator (Pentru marcatorul

cu laser)

(Numai C8FSHE)

Comutator pentru pornire

Comutator (Pentru lampă)

(Numai C8FSHE)

Marcaj (pre-marcat)

Dispozitiv de blocare a axului

Șurub cu cap plat de 6 mm

Apărătoare

Placă de așezare

Suport

Ștaif de montaj

Manetă de prindere

Șurub de reglare pe adâncime de

6 mm

Mâner glisieră de fixare (A)

Reglator (Pentru contactul laserului)

(Numai C8FSHE)

Știft de blocare

Șurub de 6 mm

Piesă de prelucrat

Placă auxiliară

Bolţ de ajustare cu adâncime de 8 mm

Piuliţă de 6 mm

Slovenščina

Ročica

Blokirni vzvod

Glava motorja

Pogonsko ohišje

Motor

Vreča za prah

Tečaj

Nosilec (A)

Svetilka (Le C8FSHE)

Indikator (Za poševno merilo)

Laserski označevalec (Samo C8FSHE)

Rezilo žage

Sestav primeža

Ograja (B)

Stranska ograja

Ročica

Stranska ročica

Obračalna miza

Ploščni vstavek

Indikator (A) (Za zajerno merilo)

Ograja (A)

Spodnje varovalo

Tesnilo (D)

Pokrov gredi

Stikalo (Za laserski N

označevalec) (Samo C8FSHE)

Sprožilno stikalo

Stikalo (Za svetilko)

(Samo C8FSHE)

Označevanje (predoznačeno)

Zaklep gred

Vijak z ugreznjeno glavo 6 mm

Varovalo

Podlaga

Nosilec

Nastavitveni zatič

Ročica objemke

Vijak za nastavitev globine

6 mm

Gumb za zavarovanje pomika (A)

Nastavljalec (Za laserski ozna

evalec)

(Samo C8FSHE)

Zaklepni zatič

6 mm sornik

Obdelovalni kos

Dodatna ploΙηa

8 mm vijak za nastavitev globine

Matica 6 mm

Română

Șurub de 6 mm cu cap fluture

(Accesoriu opţional)

Suport

(Accesoriu opţional)

Echer din oţel

Piuliţă fluture de 6 mm

(Accesoriu opţional)

Șurub de 6 mm pentru reglarea

înălţimii (accesoriu opţional)

Suprafaţa plăcii de așezare

Opritor

(Accesoriu opţional))

Bolţ de 6 mm mâner

(accesoriu opţional)

Linie

Semn de avertizare

Suport pentru șuruburi

Șurub de 6 mm cu cap fluture (B)

Arborele menghinei

Lentila lămpii

Ghidaj

Șurub de 6 mm cu cap fluture (A)

Placa menghinei

Buton

Linie laser

Canelură

Gradaţia înclinării

Scală înclinată

Ansamblul dispozitivului pivotant

de deplasare al menghinei

(Accesoriu opţional)

Piuliţă fluture de 6 mm

(Accesoriu opţional)

Opritorul dispozitivului pivotant de

deplasare (L) (Accesoriu opţional)

Opritorul dispozitivului pivotant de

deplasare (R) (Accesoriu opţional)

Dispozitiv pivotant de deplasare

Cheie inelară de 10 mm

Șurub

Lampă

Linie limită pentru uzură

Culoare (A)

Slovenščina

6 mm sornik s krilci

(opcijski dodatek)

Nosilec

(Opcijski dodatek)

Jeklen kvadrat

6 mm matica s krilci

(Opcijski dodatek)

6 mm sornik za nastavljanje višine

(Opcijski dodatek)

Površina podlage

Zaustavljalo

(Opcijski dodatek)

6 mm sornik s krilci

(opcijski dodatek)

Linija

Opozorilni simbol

Nosilec vijaka

6 mm sornik s krilci (B)

Gred primeža

Leča svetilke

Ograja

6 mm sornik s krilci (A)

Plošča primeža

Gumb

Laserska linija

Utor

Poševno merilo

Zajerno merilo

Primež kronaste oblike

(Opcijski dodatek)

6 mm matica s krilci

(Opcijski dodatek)

Omejevalnik kronaste oblike (L)

(Opcijski dodatek)

Omejevalnik kronaste oblike (R)

(Opcijski dodatek)

Kronasta oblika

10 mm ključ

Sornik

Svetilka

Omejevalna linija obrabe

Barva (A)

Türkçe

e6 mm Kelebek Cıvata

(Ósteåe baålı gelen aksesuar)

fTutamaç

(Ósteåe baålı gelen aksesuar)

gÇelik Kare

h6 mm Kelebek Cıvata

(Ósteåe baålı gelen aksesuar)

iYükseklik Ayar Cıvatası 6 mm

(Ósteåe baålı gelen aksesuar)

jTaban Yüzey

kDurdurucu

(Ósteåe baålı gelen aksesuar)

l6 mm'lik Tokmak cıvata

(Ósteåe baålı aksesuar)

mÇizgi

nUyarı ißareti

oVida Tutamacı

p6 mm Kelebek Cıvata (B)

qMengene Mili

rLamba merceåi

sSiper

t6 mm Kelebek Cıvata (A)

uMengene Tabanı

vKontrol Düåmesi

wLazer çizgisi

xOluk

yEåim ölçeåi

zÍev Ölçeåi

{Taç Kalıp Mengene Takımı

(Ósteåe baålı gelen aksesuar)

|6 mm Kelebek Cıvata

(Ósteåe baålı gelen aksesuar)

}Taç Kalıp Durdurucu (L)

(Ósteåe baålı gelen aksesuar)

~Taç Kalıp Durdurucu (R)

(Ósteåe baålı gelen aksesuar)

åTaç kalıp

ç10 mm Lokma Anahtarı

†Cıvata

¢Lamba

£Yıpranma limiti çizgisi

§Renk (A)

PyccÍËÈ

1PyÍoÓÚÍa

ÅÎoÍËpoÇoäÌêÈ pêäaÖ

3ÉoÎoÇÍa ÀÇËÖaÚeÎÓ

4KopÔyc ÔpËÇoÀa

5MoÚop

6èêÎecÄopÌËÍ

7èeÚÎÓ

8îËÍcaÚop (A)

9ãaÁep (ÚoÎëÍo C8FSHE)

0àÌÀËÍaÚop (ÑÎÓ åÍaÎê

ÌaÍÎoÌa)

AãaÁepÌêÈ yÍaÁaÚeÎë (ToÎëÍo

C8FSHE)

BèoÎoÚÌo ÔËÎê

CìÁeÎ ÚËcÍoÇ

DOÖpaÊÀeÌËe (B)

BcÔoÏoÖaÚeÎëÌoe oÖpaÊÀeÌËe

FPêäaÖ

GÅoÍoÇaÓ pyÍoÓÚÍa

HèoÇopoÚÌêÈ cÚoÎ

IBcÚaÇÍa cÚoÎa

JàÌÀËÍaÚop (ÑÎÓ åÍaÎê

peÁaÌËÓ ÔpË ÔoÇopoÚe)

KOÖpaÊÀeÌËe (A)

LHËÊÌee ÔpeÀoxpaÌËÚeÎëÌoe

ÔpËcÔocoÄÎeÌËe

MèpoÏêÇaÚeÎë (D)

NóexoÎ åÔËÌÀeÎÓ

OèepeÍÎïäaÚeÎë (ÑÎÓ ÎaÁepÌoÖo

yÍaÁaÚeÎÓ) (ToÎëÍo C8FSHE)

PèycÍoÇoÈ ÔepeÍÎïäaÚeÎë

QèepeÍÎïäaÚeÎë (ÑÎÓ ÎaÁepa)

(ToÎëÍo C8FSHE)

RMapÍËpoÇÍa (ÔpeÀÇapËÚeÎëÌo

ÔpocÚaÇÎeÌÌaÓ)

SÂaçeÎÍa åÔËÌÀeÎÓ

T6 ÏÏ ÇËÌÚ c ÔÎocÍoÈ ÖoÎoÇÍoÈ

UèpeÀoxpaÌËÚeÎëÌoe ycÚpoÈcÚÇo

VOcÌoÇaÌËe

WîËÍcaÚop

PyccÍËÈ

XìcÚaÌoÇoäÌêÈ åÚËÙÚ

Y3aÊ

È pêya

Z6 ÏÏ ÇËÌÚ c ÔÎocÍoÈ ÖoÎoÇÍoÈ

[PyÍoÓÚÍa ÙËÍcËpoÇaÌËÓ

cÍoÎëÊeÌËÓ (A)

PeÖyÎÓÚop (ÀÎÓ ÎaÁepÌoÖo ÏapÍepa)

(ToÎëÍo C8FSHE)

]CÚoÔopÌaÓ åÔËÎëÍa

`6 ÏÏ ÄoÎÚ

aÂaÖoÚoÇÍa

bÑoÔoÎÌËÚeÎëÌêÈ ÔyÎëÚ

c8-ÏËÎÎËÏeÚpoÇêÈ ÄoÎÚ

peÖyÎËpoÇaÌËÓ ÖÎyÄËÌê

d6 ÏÏ ÉaÈÍa

6 ÏÏ ÄapaåÍoÇêÈ ÄoÎÚ

(ÀoÔoÎÌËÚeÎëÌaÓ ÔpËÌaÀÎeÊÌocÚë)

fîËÍcaÚop (ÀoÔoÎÌËÚeÎëÌaÓ

ÔpËÌaÀÎeÊÌocÚë)

gCÚaÎëÌoÈ yÖoÎëÌËÍ

h6 ÏÏ ÄapaåÍoÇaÓ ÖaÈÍa

(ÀoÔoÎÌËÚeÎëÌaÓ ÔpËÌaÀÎeÊÌocÚë)

i6 ÏÏ ÄoÎÚ peÖyÎËpoÇÍË ÇêcoÚê

(ÀoÔoÎÌËÚeÎëÌaÓ ÔpËÌaÀÎeÊÌocÚë)

jOÔopÌaÓ ÔoÇepxÌocÚë

kCÚoÔop (ÀoÔoÎÌËÚeÎëÌaÓ

ÔpËÌaÀÎeÊÌocÚë)

6-ÏËÎÎËÏeÚpoÇêÈ cÚoÔopÌêÈ

ÄoÎÚ (ÀoÔoÎÌËÚeÎëÌaÓ

ÔpËÌaÀÎeÊÌocÚë)

mãËÌËÓ

nèpeÀyÔpeÊÀaïçËÈ ÁÌaÍ

oBËÌÚoÇoÈ ÙËÍcaÚop

p6 ÏÏ ÅapaåÍoÇêÈ ÄoÎÚ (B)

qBaÎ ÚËcÍoÇ

rãËÌÁa ÎaÁepa

sãËÌeÈÍa

t6 ÏÏ ÄapaåÍoÇêÈ ÄoÎÚ (A)

uèÎacÚËÌa ÚËcÍoÇ

vPyÍoÓÚÍa

wãËÌËÓ ÎaÁepa

xèaÁ

yòÍaÎa ÌaÍÎoÌa

zòÍaÎa peÁaÌËÓ ÔpË ÔoÇopoÚe

PyccÍËÈ

{

ìÁeÎ ÚËcÍoÇ oÔpeccoÇÍË ÇeÌáa

(ÀoÔoÎÌËÚeÎëÌaÓ ÔpËÌaÀÎeÊÌocÚë)

|6 ÏÏ ÄapaåÍoÇaÓ ÖaÈÍa

(ÀoÔoÎÌËÚeÎëÌaÓ ÔpËÌaÀÎeÊÌocÚë)

}

CÚoÔop oÔpeccoÇÍË ÇeÌáa (L)

(ÀoÔoÎÌËÚeÎëÌaÓ ÔpËÌaÀÎeÊÌocÚë)

CÚoÔop oÔpeccoÇÍË ÇeÌáa (R)

(ÀoÔoÎÌËÚeÎëÌaÓ ÔpËÌaÀÎeÊÌocÚë)

åOÔpeccoÇÍa ÇeÌáa

ç10 ÏÏ ÌaÍËÀÌoÈ ÍÎïä

†ÅoÎÚ

¢ãaÁep

£ãËÌËÓ ÔpeÀeÎëÌoÖo ËÁÌoca

§ñÇeÚ (A)

Symbols

The following show

symbols used for the

machine. Be sure that

you understand their

meaning before use.

Symbole

Die folgenden Symbole

werden für diese

Maschine verwendet.

Achten Sie darauf, diese

vor der Verwendung zu

verstehen.

™‡Ì‚ÔÏ·

Τα παρακάτω δείνυν τα

σύµλα πυ

ρησιµπιύνται στ

µηάνηµα. Βεαιωθείτε τι

κατανείτε τη σηµασίας

τυς πριν τη ρήση.

Symbole

Następujące oznaczenia

to symbole używane w

instrukcji obsługi

maszyny. Upewnij się, że

rozumiesz ich znaczenie

zanim użyjesz narzędzia.

Read instruction

manual.

Bedienungsanleitung

lesen.

∆ιαάστε τ

εγειρίδι δηγιών. Przeczytaj instrukcje.

Always wear eye

protection.

Tragen Sie immer

einen Augenschutz.

Φράτε πάντα τν

κατάλληλ επλισµ

για την πρστασία

των µατιών.

Zawsze nosić okulary

ochronne.

Přečtěte si návod.

Vždy noste ochranu

očí.

Kullanım kılavuzunu

okuyun.

Daima koruyucu

gözlük takın.

èpoäÚËÚe

pyÍoÇoÀcÚÇo Ôo

íÍcÔÎyaÚaáËË.

BceÖÀa ÌaÀeÇaÈÚe

cpeÀcÚÇa ÁaçËÚê

ÖÎaÁ.

Symboly

Následující text obsahuje

symboly, které jsou použity

na zařízení. Ujistěte se, že

rozumíte jejich obsahu

před tím, než začnete

zařízení používat.

Simgeler

Aßaåıda, bu alet için kullanılan

simgeler gösterilmißtir. Aleti

kullanmadan önce bu

simgelerin ne anlama geldiåini

anladıåınızdan emin olun.

CËÏÇoÎê

HËÊe ÔpËÇeÀeÌê cËÏÇoÎê,

ËcÔoÎëÁyeÏêe ÀÎÓ

ÏaåËÌê. èepeÀ ÌaäaÎoÏ

paÄoÚê oÄÓÁaÚeÎëÌo

yÄeÀËÚecë Ç ÚoÏ, äÚo Bê

ÔoÌËÏaeÚe Ëx ÁÌaäeÌËe.

Only for EU countries

Do not dispose of electric

tools together with

household waste material!

In observance of European

Directive 2002/96/EC on

waste electrical and

electronic equipment and

its implementation in

accordance with national

law, electric tools that have

reached the end of their life

must be collected

separately and returned to

an environmentally

compatible recycling

facility.

Nur für EU-Länder

Werfen Sie

Elektrowerkzeuge nicht

in den Hausmüll!

Gemäss Europäischer

Richtlinie 2002/96/EG

über Elektro- und

Elektronik- Altgeräte

und Umsetzung in

nationales Recht

müssen verbrauchte

Elektrowerkzeuge

getrennt gesammelt

und einer

umweltgerechten

Wiederververtung

zugeführt werden.

Mvo για τις ώρες της

Mηv πετάτε τα ηλεκτρικά

εργαλεία στov κάδo

oικιακώv απoρριµµάτωv!

Σύµωvα µε τηv

εuρωπαϊκή oδηγία 2002/

96/EK περί ηλεκτρικώv και

ηλεκτρovικώv σuσκεuώv

και τηv εvσωµάτωσή της

στo εθvικ δίκαιo, τα

ηλεκτρικά εργαλεία

πρέπει vα σuλλέγovται

εωριστά και vα

επιστρέovται για

αvακύκλωση µε τρπo

ιλικ πρoς τo

περιάλλov.

Dotyczy tylko państw UE

Nie wyrzucaj

elektronarzędzi wraz z

odpadami z

gospodarstwa

domowego!

Zgodnie z Europejską

Dyrektywą 2002/96/WE w

sprawie zużytego sprzętu

elektrotechnicznego i

elektronicznego oraz

dostosowaniem jej do

prawa krajowego, zużyte

elektronarzędzia należy

posegregować i

zutylizować w sposób

przyjazny dla środowiska.

Jen pro státy EU

Elektrické nářadí

nevyhazujte do

komunálního odpadu!

Podle evropské

směrnice 2002/96/EG o

nakládání s použitými

elektrickými a

elektronickými

zařízeními a

odpovídajících

ustanovení právních

předpisů jednotlivých

zemí se použitá

elektrická nářadí musí

sbírat odděleně od

ostatního odpadu a

podrobit ekologicky

šetrnému recyklování.

Sadece AB ülkeleri için

Elektrikli el aletlerini

evdeki çöp kutusuna

atmayınız!

Kullanılmıß elektrikli

aletleri, elektrik ve

elektronikli eski

cihazlar hakkındaki

2002/96/EC Avrupa

yönergelerine göre ve

bu yönergeler ulusal

hukuk kurallarına göre

uyarlanarak, ayrı

olarak toplanmalı ve

çevre ßartlarına uygun

bir ßekilde tekrar

deåerlendirmeye

gönderilmelidir.

ToÎëÍo ÀÎÓ cÚpaÌ EC

He ÇêÍËÀêÇaÈÚe

íÎeÍÚpoÔpËÄopê ÇÏecÚe

c oÄoêäÌêÏ ÏycopoÏ!

B cooÚÇeÚcÚÇËË c

eÇpoÔeÈcÍoÈ

ÀËpeÍÚËÇoÈ 2002/96/EG

oÄ yÚËÎËÁaáËË cÚapêx

íÎeÍÚpËäecÍËx Ë

íÎeÍÚpoÌÌêx ÔpËÄopoÇ

Ë Ç cooÚÇeÚcÚÇËË c

ÏecÚÌêÏË ÁaÍoÌaÏË

íÎeÍÚpoÔpËÄopê,

ÄêÇçËe Ç

íÍcÔÎyaÚaáËË, ÀoÎÊÌê

yÚËÎËÁoÇêÇaÚëcÓ

oÚÀeÎëÌo ÄeÁoÔacÌêÏ

ÀÎÓ oÍpyÊaïçeÈ cpeÀê

cÔocoÄoÏ.

Jelölések

Az alábbiakban a géphez

alkalmazott jelölések

vannak felsorolva. A gép

használata előtt feltétlenül

ismerje meg ezeket a

jelöléseket.

Mindig viseljen

védőszemüveget.

Csak EU-országok

számára

Az elektromos

kéziszerszámokat ne

dobja a háztartási

szemétbe!

A használt villamos és

elektronikai

készülékekről szóló

2002/96/EK irányelv és

annak a nemzeti jogba

való átültetése szerint

az elhasznált

elektromos

kéziszerszámokat

külön kell gyűjteni, és

környezetbarát módon

újra kell hasznosítani.

Olvassa el a

Használati utasítást.

Preberite navodila za

uporabo.

Uporaba zaščite za

oči je obvezna.

Simboli

V nadaljevanju so

prikazani simboli,

uporabljeni pri stroju.

Pred uporabo se

prepričajte, da jih

razumete.

Samo za države EU

Električnih orodij ne

zavržite skupaj z

gospodinjskimi

odpadki!

V skladu z evropsko

direktivo 2002/96/EC

o odpadni električni in

elektronski opremi in

izvedbi v skladu z

državnimi zakoni, je

treba električna

orodja, ki so dosegla

življenjsko dobo

ločeno zbirati in vrniti

v z okoljem združljivo

ustanovo za

recikliranje.

Citiţi manualul de

instrucţiuni.

Purtaţi întotdeauna

protecţie pentru ochi.

Simboluri

În cele ce urmează sunt

prezentate simbolurile

folosite pentru mașină.

Înainte de utilizare,

asiguraţi-vă că înţelegeţi

semnificaţia acestora.

Numai pentru ţările membre

Nu aruncaţi această sculă

electrică împreună cu

deșeurile menajere!

În conformitate cu Directiva

Europeană 2002/96/CE

referitoare la deșeurile

reprezentând echipamente

electrice și electronice și la

implementarea acesteia în

conformitate cu legislaţiile

naţionale, sculele electrice

care au ajuns la finalul

duratei de folosire trebuie

colectate separat și duse la o

unitate de reciclare

compatibilă cu mediul

înconjurător.

Always wear

hearing protection.

Stets Gehörschutz

tragen.

Φράτε πάντα

πρστατευτικά

ακής.

Zawsze nosić

słuchawki ochronne.

Mindig viseljen a

hallást védő

védőfelszerelést.

Vždy používejte

chrániče sluchu. Daima koruyucu

kulaklık takın.

BceÖÀa ÌaÀeÇaÈÚe

cpeÀcÚÇa ÁaçËÚê

opÖaÌoÇ cÎyxa.

Purtaţi întotdeauna

protecţie auditivă. Obvezna je uporaba

zaščite za ušesa.

English

GENERAL OPERATIONAL PRECAUTIONS

WARNING! When using electric tools, basic safety precautions should always be

followed to reduce the risk of fire, electric shock and personal injury, including

the following.

Read all these instructions before operating this product and save these

instructions.

For safe operations:

1. Keep work area clean. Cluttered areas and benches invite injuries.

2. Consider work area environment. Do not expose power tools to rain. Do

not use power tools in damp or wet locations. Keep work area well lit.

Do not use power tools where there is risk to cause fire or explosion.

3. Guard against electric shock. Avoid body contact with earthed or grounded

surfaces (e.g. pipes, radiators, ranges, refrigerators).

4. Keep children and infirm persons away. Do not let visitors touch the tool

or extension cord. All visitors should be kept away from work area.

5. Store idle tools. When not in use, tools should be stored in a dry, high or

locked up place, out of reach of children and infirm persons.

6. Do not force the tool. It will do the job better and safer at the rate for

which it was intended.

7. Use the right tool. Do not force small tools or attachments to do the job of

a heavy duty tool. Do not use tools for purposes not intended; for example,

do not use circular saw to cut tree limbs or logs.

8. Dress properly. Do not wear loose clothing or jewelry, they can be caught

in moving parts. Rubber gloves and non-skid footwear are recommended

when working outdoors. Wear protecting hair covering to contain long

hair.

9. Use eye protection. Also use face or dust mask if the cutting operation is

dusty.

10. Connect dust extraction equipment.

Cutting operation by this compound saw may produce considerable

amount of dust from extraction duct on fixed guard.

(Dust material: Wood or Aluminium)

If devices are provided for the connection of dust extraction and collection

facilities ensure these are connected and properly used.

11. Do not abuse the cord. Never carry the tool by the cord or yank it to

disconnect it from the receptacle. Keep the cord away from heat, oil and

sharp edges.

12. Secure work. Use clamps or a vise to hold the work. It is safer than using

your hand and it frees both hands to operate tool.

13. Do not overreach. Keep proper footing and balance at all times.

14. Maintain tools with care. Keep cutting tools sharp and clean for better

and safer performance. Follow instructions for lubrication and changing

accessories. Inspect tool cords periodically and if damaged, have it repaired

by authorized service center. Inspect extension cords periodically and

replace, if damaged. Keep handles dry, clean, and free from oil and grease.

15. Disconnect tools. When not in use, before servicing, and when changing

accessories such as blades, bits and cutters.

16. Remove adjusting keys and wrenches. Form the habit of checking to see

that keys and adjusting wrenches are removed from the tool before turning

it on.

17. Avoid unintentional starting. Do not carry a plugged-in tool with a finger

on the switch. Ensure switch is off when plugging in.

18. Use outdoor extension leads. When tool is used outdoors, use only

extension cords intended for outdoor use.

19. Stay alert. Watch what you are doing. Use common sense. Do not operate

tool when you are tired.

20. Check damaged parts. Before further use of the tool, a guard or other part

that is damaged should be carefully checked to determine that it will

operate properly and perform its intended function. Check for alignment

of moving parts, free running of moving parts, breakage of parts, mounting

and any other conditions that may affect its operation. A guard or other

part that is damaged should be properly repaired or replaced by an

authorized service center unless otherwise indicated in this handling

instructions. Have defective switches replaced by an authorized service

center. Do not use the tool if the switch does not turn it on and off.

21. Warning

The use of any accessory or attachment, other than those recommended

in this handling instructions, may present a risk of personal injury.

22. Have your tool repaired by a qualified person.

This electric tool is in accordance with the relevant safety requirements.

Repairs should only be carried out by qualified persons using original

spare parts. Otherwise this may result in considerable danger to the user.

PRECAUTIONS ON USING SLIDE COMPOUND

MITER SAW

1. Keep the floor area around the machine level. Well maintained and free of฀

loose materials e.g. chips and cut-offs.

2. Provide adequate general or localized lighting.

3. Do not use power tools for applications other than those specified in the฀

handling instructions.

4. Repairing must be done only by authorized service facility. Manufacturer฀

is not responsible for any damages and injuries due to the repair by the฀

unauthorized persons as well as the mishandling of the tool.

5. To ensure the designed operational integrity of power tools, do not remove฀

installed covers or screws.

6. Do not touch movable parts or accessories unless the power source has฀

been disconnected.

7. Use your tool at lower input than specified on the nameplate; otherwise,฀

the finish may be spoiled and working efficiency reduced due to motor฀

overload.

8. Do not wipe plastic parts with solvent. Solvents such as gasoline, thinner,฀

benzine, carbon tetrachloride, alcohol, may damage and crack plastic parts.฀

Do not wipe them with such solvent. Clean plastic parts with a soft cloth฀

lightly dampened with soapy water.

9. Use only original HiKOKI replacement parts.

10. This tool should only be disassembled for replacement of carbon brushes.

11. The exploded assembly drawing on this handling instructions should be฀

used only for authorized service facility.

12. Never cut ferrous metals or masonry.

13. Adequate general or localized lighting is provided. Stock and finished฀

workpieces are located close to the operators normal working position.

14. Wear suitable personal protective equipment when necessary, this could฀

include:

Hearing protection to reduce the risk of induced hearing loss.

Eye protection to reduce the risk of injuring an eye.

Respiratory protection to reduce the risk of inhalation of harmful dust.฀

Gloves for handling saw blades (saw blades shall be carried in a holder฀

wherever practicable) and rough material.

15. The operator is adequately trained in the use, adjustment and operation฀

of the machine.

16. Refrain from removing any cut-offs or other parts of the workpiece from฀

the cutting area whilst the machine is running and the saw head is not in฀

the rest position.

17. Never use the slide compound miter saw with its lower guard locked in฀

the open position.

18. Ensure that the lower guard moves smoothly.

19. Do not use the saw without guards in position, in good working order and฀

properly maintained.

20. Use correctly sharpened saw blades. Observe the maximum speed marked฀

on the saw blade.

21. Do not use saw blades which are damaged or deformed.

22. Do not use saw blades manufactured from high speed steel.

23. Use only saw blades recommended by HiKOKI.

Use of saw blade comply with EN847-1.

24. The saw blades should be 216 mm external diameter.

25. Select the correct saw blade for the material to be cut.

26. Never operate the slide compound miter saw with the saw blade turned฀

upward or to the side.

27. Ensure that the workpiece is free of foreign matter such as nails.

28. Replace the table insert when worn.

29. Do not use the saw to cut other than aluminium, wood or similar materials.

30. Do not use the saw to cut other materials than those recommended by฀

the manufacturer.

31. Blade replacement procedure, including the method for repositioning and฀

a warning that this must be carried out correctly.

32. Connect the slide compound miter saw to a dust collecting device when฀

sawing wood.

33. Take care when slotting.

34. When transporting or carrying the tool, do not grasp the holder. Grasp฀

the handle instead of the holder.

35. Start cutting only after motor revolution reaches maximum speed.

36. Promptly cut OFF the switch when abnormality observed.

37. Shut off power and wait for saw blade to stop before servicing or adjusting฀

tool.

38. During a miter or bevel cut the blade should not be lifted until it has stopped฀

rotation completely.

English

39. During slide cutting operation, the saw must be pushed and slided away

from the operator.

40. Take all the possibility of residual risks in cutting operation into your

consideration, such as the laser radiation to your eyes, the inadvertent

access to moving parts on slide mechanical parts on machine and so on.

SPECIFICATIONS

0° 65 mm × 312 mm

**75 mm × 262 mm with aux. board (30 mm)

Miter 45° 65 mm × 220 mm

**75 mm × 185 mm with aux. board (20 mm)

Left 45° 45 mm × 312 mm

**50 mm × 252 mm with aux. board (30 mm)

Bevel

Right 5° 60 mm × 312 mm

**70 mm × 252 mm with aux. board (30 mm)

Bevel (Left) 45° + Miter 45°

45 mm × 220 mm

Compound **50 mm × 170 mm with aux. board (30 mm)

Bevel (Right) 5° + Miter 45° 60 mm × 220 mm

**70 mm × 170 mm with aux. board (30 mm)

Saw Blade Dimensions (oD × iD × Thickness) 216 mm × 30 mm × 2 mm

Miter Cutting Angle Right 0° – 57°, Left 0° – 45°

Bevel Cutting Angle Right 0° – 5°, Left 0° – 48°

Compound Cutting Angle Bevel (Left) 0° – 45° Miter (Right and Left) 0° – 45°

Bevel (Right) 0° – 5°

Voltage (by areas)* (110 V, 230 V)

Power Input* 1050 W

No-Load Speed 5500 min–1

Machine Dimensions (Width × Depth × Height) 555 mm × 790 mm × 485 mm

Weight (Net) 15 kg (C8FSHE) / 14 kg (C8FSE)

Maximum output Po<3 mW Class Laser Product

(Iambda) 654 nm

Laser medium Laser Diode

Max. Cutting

Capacity

Height × Width

Laser Marker

(Only Model C8FSHE)

* Be sure to check the nameplate on product as it is subject to change by areas.

When cutting the workpiece which has the dimension of “**” there might be some possibility of the lower end of the circular saw to touch with the workpiece, even if

the motor head is located at the lower limit position. Pay attention when cutting the workpiece. For further details, refer to “PRACTICAL APPLICATIONS”. Mount the

auxiliary board on the fence surface (Refer ( ) the thickness of auxiliary board). Refer to "12. Cutting large workpieces" (Fig. 16).

STANDARD ACCESSORIES

(1) 216 mm TCT Saw blade (mounted on tool) .................................................. 1

(2) Dust bag ........................................................................................................... 1

(3) 10 mm Box wrench ......................................................................................... 1

(4) Vise Assembly ................................................................................................. 1

(5) Holder ............................................................................................................... 1

(6) Side Handle ...................................................................................................... 1

Standard accessories are subject to change without notice.

OPTIONAL ACCESSORIES (SOLD SEPARATELY)

(1) Extension Holder and Stopper

(2) Saw blade 216 mm TCT Saw blade (Total teeth: 60)

(3) Crown molding Vise Ass'y (Include Crown molding Stopper (L))

(4) Crown molding Stopper (L)

(5) Crown molding Stopper (R)

(6) Sub Fence

Optional accessories are subject to change without notice.

APPLICATION

䡬

Cutting various types of aluminium sash and wood.

UNPACKING

䡬

Carefully unpack the power tool and all related items (standard accessories).

䡬

Check carefully to make certain all related items (standard accessories) are

present.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms to the power

requirements specified on the product nameplate.

2. Power switch

Ensure that the power switch is in the OFF position. If the plug is connected

to a receptacle while the trigger switch is in the ON position, the power tool

will start operating immediately, inviting serious accident.

English

3. Extention cord

When the work area is removed from the power source, use an extension

cord of sufficient thickness and rated capacity. The extension cord should be

kept as short as practicable.

4. When the power tool is prepared for shipping, its main parts are secured by

a locking pin

Move the handle slightly so that the locking pin can be disengaged.

During transport, lock the locking pin into the gear case (Fig. 4).

5. Attach the dust bag to the main unit (Fig. 1)

6. Installation

Ensure that the machine is always fixed to bench.

Attach the power tool to a level, horizontal work bench.

Select 8 mm diameter bolts suitable in length for the thickness of the work

bench.

Bolt length should be at least 25 mm plus the thickness of the work bench.

For example, use 8 mm × 65 mm bolts for a 25 mm thick work bench.

ADJUSTING THE POWER TOOL PRIOR TO USE

CAUTION

Make all necessary adjustments before inserting the plug in the power source.

1. Check to see that the lower guard operates smoothly

CAUTION

䡬

This slide compound miter saw is equipped with a saw head lock as safety

device.

䡬

To lower the saw head to cut, the lock must be released by pressing the lock

lever with your thumb.

(1) When you push down the handle while pushing the lock lever, check that

the lower guard revolves smoothly (Fig. 5).

(2) Next, check that the lower guard returns to the original position when the

handle is raised.

2. Checking the saw blade lower limit position (Fig. 6 and Fig. 7)

Check that the saw blade can be lowered 10 mm to 11 mm below the table

insert.

When you replace a saw blade with a new one, adjust the lower limit position

so that the saw blade will not cut the turntable or complete cutting cannot

be done.

To adjust the lower limit position of the saw blade, follow the procedure (1)

indicated below. (Fig. 7)

Furthermore, when changing the position of a 8 mm depth adjustment bolt

that serves as a lower limit position stopper of the saw blade.

(1) Turn the 8 mm depth adjustment bolt, change the height where the bolt

head and the hinge contacts, and adjust the lower limit position of the saw

blade.

NOTE

Confirm that the saw blade is adjusted so that it will not cut into the turntable.

3. Lower limit position of saw blade when cutting a large workpiece

NOTE

When cutting a workpiece exceeding 65 mm in height in right-angle cutting

or 60 mm in left bevel angle cutting or 45 mm in right bevel angle cutting,

adjust the lower limit position so that the base of the motor head (Fig. 6) will

not come in contact with the workpiece.

PRACTICAL APPLICATIONS

WARNING

䡬

To avoid personal injury, never remove or place a workpiece on the table

while the tool is being operated.

䡬

Never place your limbs inside of the line next to warning sign while the tool

is being operated. This may cause hazardous conditions (See Fig. 8).

CAUTION

䡬

It is dangerous to remove or install the workpiece while the saw blade is

turning.

䡬

When sawing, clean off the shavings from the turntable.

䡬

If the shavings accumulate too much, the saw blade from the cutting material

will be exposed. Never subject your hand or anything else to go near the

exposed blade.

1. Tightly secure the material by vise assembly to be cut so that it does not

move during cutting

2. Switch operation

Pulling the trigger turns the switch on. Releasing the trigger turns the switch

off.

3. Base holder adjustment (Fig. 3)

Loosen the 6 mm bolt with the supplied 10 mm box wrench. Adjust the base

holder until its bottom surface contacts the bench or the floor surface.

After adjustment, firmly tighten the 6 mm bolt.

4. Using the Vise Assembly (Standard accessory) (Fig. 9)

(1) The vise assembly can be mounted on either the left fence {Fence (B)} or the

right fence {Fence (A)} by loosening the 6 mm wing bolt (A).

(2) The screw holder can be raised or lowered according to the height of the

workpiece by loosening the 6 mm wing bolt (B). After the adjustment, firmly

tighten the 6 mm wing bolt (B) and fix the screw holder.

(3) Turn the upper knob and securely fix the workpiece in position.

WARNING

䡬

Always firmly clamp or vise to secure the workpiece to the fence; otherwise

the workpiece might be thrust from the table and cause bodily harm.

CAUTION

䡬

Always confirm that the motor head does not contact the vise assembly

when it is lowered for cutting. If there is any danger that it may do so, loosen

the 6 mm wing bolt and move the vise assembly to a position where it will

not contact the saw blade.

5. Positioning the table insert (Fig. 1)

Table inserts are installed on the turntable. When shipping the tool from the

factory, the table inserts are so fixed that the saw blade does not contact

them. The burr of the bottom surface of the workpiece is remarkably reduced,

if the table insert is fixed so that the gap between the side surface of the

table insert and the saw blade will be minimum. Before using the tool,

eliminate this gap in accordance with the following procedure.

(1) Right angle cutting

Loosen the three 6 mm machine screws, then secure the left side table insert

and temporarily tighten the 6 mm machine screws of both ends. Then fix a

workpiece (about 200 mm wide) with the vise assembly and cut it off. After

aligning the cutting surface with the edge of the table insert, securely tighten

the 6 mm machine screws of both ends. Remove the workpiece and securely

tighten the 6 mm center machine screw. Adjust the right hand table insert in

the same way.

(2) Left and right bevel angle cutting

Adjust the table insert in the manner same procedure for right angle cutting.

CAUTION

䡬

After adjusting the table insert for right angle cutting, the table insert will be

cut to some extent if it is used for bevel angle cutting.

When bevel cutting operation is required, adjust the table insert for bevel

angle cutting.

6. Confirmation for use of sub fence (Optional accessory)

This power tool is equipped with a sub fence. In the case of direct angle

cutting and right bevel angle cutting, use the sub fence. Then, you can do

Left bevel angle cutting, Right bevel angle cutting and Direct angle cutting

and realize stable cutting of the material with a wide back face.

WARNING

䡬

In the case of left bevel cutting, turn the sub fence counterclockwise (Fig.

10). Unless it is turned counterclockwise, the main body or saw blade may

contact the sub fence, resulting in an injury.

7. Using an ink line

Upon lowering the motor section, the lower guard is raised and the saw

blade appears.

Align the ink line with the saw blade.

CAUTION

Never lift the lower guard while the saw blade is rotating.

The sub fence will not only make contact and adversely affect cutting

accuracy, this could also result in damage to the guard.

English

8. Install the side handle (Fig. 1)

Install the side handle that came enclosed with this unit.

9. Position adjustment of laser line (Only Model C8FSHE)

Ink lining can be easily made on this tool to the laser marker. A switch lights

up the laser marker (Fig. 11).

Depending upon your cutting choice, the laser line can be aligned with the

left side of the cutting width (saw blade) or the ink line on the right side.

The laser line is adjusted to the width of the saw blade at the time of factory

shipment. Adjust the positions of the saw blade and the laser line taking the

following steps to suit the use of your choice.

(1) Light up the laser marker and make a groove of about 5 mm deep on the workpiece

that is about 20 mm in height and 150 mm in width. Hold the grooved workpiece

by vise as it is and do not move it. For grooving work, refer to “21. Groove cutting

procedures”.

(2) Then, turn the adjuster and shift the laser line. (If you turn the adjuster

clockwise, the laser line will shift to the right and if you turn it

counterclockwise, the laser line will shift to the left.) When you work with

the ink line aligned with the left side of the saw blade, align the laser line

with the left end of the groove (Fig. 12). When you align it with the right side

of the saw blade, align the laser line with the right side of the groove.

(3) After adjusting the position of the laser line, draw a right-angle ink line on

the workpiece and align the ink line with the laser line. When aligning the

ink line, slide the workpiece little by little and secure it by vise at a position

where the laser line overlaps with the ink line. Work on the grooving again

and check the position of the laser line. If you wish to change the laser line’s

position, make adjustments again following the steps from (1) to (3).

WARNING

䡬

Make sure before plugging the power plug into the receptacle that the main

body and the laser marker are turned off.

䡬

Exercise utmost caution in handling a switch trigger for the position

adjustment of the laser line, as the power plug is plugged into the receptacle

during operation.

If the switch trigger is pulled inadvertently, the saw blade can rotate and

result in unexpected accidents.

䡬Do not remove the laser marker to be used for other purposes.

CAUTION (Fig. 13)

䡬

Laser radiation - Do not stare into beam.

䡬

Laser radiation on work table. Do not stare into beam.

If your eye is exposed directly to the laser beam, it can be hurt.

䡬

Do not dismantle it.

䡬

Do not give strong impact to the laser marker (main body of tool); otherwise,

the position of a laser line can go out of order, resulting in the damage of the

laser marker as well as a shortened service life.

䡬

Keep the laser marker lit only during a cutting operation. Prolonged lighting

of the laser marker can result in a shortened service life.

䡬

Use of controls or adjustments or performance of procedures other than

those specified herein may result in hazardous radiation exposure.

NOTE

䡬

Perform cutting by overlapping the ink line with the laser line.

䡬

When the ink line and the laser line are overlapped, the strength and weakness

of light will change, resulting in a stable cutting operation because you can

easily discern the conformity of lines. This ensures the minimum cutting

errors.

䡬

In outdoor or near-the-window operations, it may become dificult to observe

the laser line due to the sunlight. Under such circumstances, move to a place

that is not directly under the sunlight and engage in the operation.

䡬

Do not tug on the cord behind the motor head or hook your finger, wood

and the like around it; otherwise, the cord may come off and the laser marker

may not be lit up.

䡬

Check and make sure on a periodic basis if the position of the laser line is in

order. As regards the checking method, draw a right-angle ink line on the

workpiece with the height of about 20 mm and the width of 150 mm, and

check that the laser line is in line with the ink line [The deviation between the

ink line and the laser line should be less than the ink line width (0.5 mm)].

(Fig. 14)

10. Cutting operation

(1) As shown in Fig. 15 the width of the saw blade is the width of the cut.

Therefore, slide the workpiece to the right (viewed from the operator’s

position) when length is desired, or to the left when length is desired.

If a laser marker is used, align the laser line with the left side of the saw

blade, and then align the ink line with the laser line.

(2) After turning on the switch and checking that the saw blade is rotating at

maximum speed, slowly push down the handle while holding down the lock

lever and bring the saw blade in the vicinity of the material to be cut.

(3) Once the saw blade contacts the workpiece, push the handle down gradually

to cut into the workpiece.

(4) After cutting the workpiece to the desired depth, turn the power tool OFF

and let the saw blade stop completely before raising the handle from the

workpiece to return it to the full retract position.

CAUTION

䡬

For maximum dimensions for cutting, refer to “SPECIFICATIONS” table.

䡬

Increased pressure on the handle will not increase the cutting speed. On the

contrary, too much pressure may result in overload of the motor and/or

decreased cutting efficiency.

䡬

Confirm that the trigger switch is turned OFF and the power plug has been

removed from the receptacle whenever the tool is not in use.

䡬

Always turn the power off and let the saw blade stop completely before

raising the handle from the workpiece. If the handle is raised while the saw

blade is still rotating, the cut-off piece may become jammed against the saw

blade causing fragments to scatter about dangerously.

䡬

Every time one cutting of deep-cutting operation is finished, turn the switch

off, and check that the saw blade has stopped. Then raise the handle, and

return it to the full retract position.

䡬

Be absolutely sure to remove the cut material from the top of the turntable,

and then proceed to the next step.

11. Cutting narrow workpieces (Press cutting)

Slide the hinge down to holder (A), then tighten the slide securing knob (Fig.

2). Lower the handle to cut the workpiece. Using the power tool this way will

permit cutting of workpieces of up to 65 mm square.

12. Cutting large workpieces

There may be case when a complete cutting cannot be done depending on

the height of workpiece. In this case, mount an auxiliary board with the 6mm

flat head screws and the 6mm nuts using the 7mm holes on the fence surface

(two holes on each side). (Fig. 16)

Refer to "SPECIFICATIONS" for the thickness of the auxiliary board.

13. Cutting wide workpieces (Slide cutting)

Loosen the slide securing knob (Fig. 2), grip the handle and slide the saw

blade forward. Then press down on the handle and slide the saw blade back

to cut the workpiece. This facilitates cutting of workpieces of up to 312 mm

in width.

WARNING

䡬

Never put your hand on the side handle during the cutting operation because

the saw blade comes close to the side handle when the motor head is lowered.

14. Miter cutting procedures

(1) Loosen the side handle and pull up the lever for angle stoppers. Then, adjust

the turntable until the indicator aligns with desired setting on the miter scale

(Fig. 17).

(2) Re-tighten the side handle to secure the turntable in the desired position.

(3) The miter scale indicates both the cutting angle on the angle scale and the

gradient on the grade scale.

(4) The gradient, which is the ratio of the height to the base of the triangular

section to be removed, may be used for setting the miter scale instead of

the cutting angle, if desired.

(5) Therefore, to cut a workpiece at a grade of 2/10, set the indicator to position.

NOTE

䡬

Positive stops are provided at the right and left of the 0° center setting, at

15°, 22.5°, 31.6° and 45° settings.

Check that the miter scale and the tip of the indicator are properly aligned.

䡬

Operation of the saw with the miter scale and indicator out of alignment, or

with the side handle not properly tightened, will result in poor cutting

precision.

English

15. Bevel cutting procedures (Fig. 18)

CAUTION

䡬

Ensure that the clamp lever is securely fixed when beveling.

䡬

Please do this if the length of the material being cut off is more than 25 mm

long. Sometimes cutting cannot be accomplished because the saw blade

will catch on the inside of the lower guard.

(1) Loosen the clamp lever and bevel the saw blade to the left or to the right.

When tilting the motor head to the right pull the set pin towards the rear.

NOTE

Loosen the clamp lever, tilt the main unit to the left and then pull the set pin

to enable 48-degree cuts.

Loosen the clamp lever and slant to the left a little at a time while pushing

the set pin into the main unit. At this time, the set pin will enter one step and

fit into the 30° left slant and 33.9° left slant setting slots.

With the set pin in the slot as described above, setting to the 30° left slant

position is possible by pushing to the right side.

Also, with the set pin in the slot as described above, setting to the 33.9° left

slant position is possible by pushing to the left side.

(2) Adjust the bevel angle to the desired setting while watching the

bevel angle scale and indicator, then secure the clamp lever.

WARNING

䡬

When the workpiece is secured on the left or right side of the blade, the short

cut-off portion will come to rest on the right or left side of the saw blade.

Always turn the power off and let the saw blade stop completely before raising

the handle from the workpiece.

If the handle is raised while the saw blade is still rotating, the cut-off piece may

become jammed against the saw blade causing fragments to scatter about

dangerously.

When stopping the bevel cutting operation halfway, start cutting after pulling

back the motor head to the initial position.

Starting from halfway, without pulling back, causes the lower guard to be

caught in the cutting groove of the workpiece and to contact the saw blade.

16. Compound cutting procedures

Compound cutting can be performed by following the instructions in 13 and

14 above. For maximum dimensions for compound cutting, refer to

“SPECIFICATIONS” table.

CAUTION

䡬

Always secure the workpiece with the right or left hand and cut it by sliding

the round portion of the saw backwards with the left hand.

It is very dangerous to rotate the turntable to the left during compound cutting

because the saw blade may come into contact with the hand that is securing

the workpiece.

In case of compound cutting (angle + bevel) by left bevel, turn the sub-fence

(optional accessory) counterclockwise, and engage in the cutting operation.

17. Cutting long materials

When cutting long materials, use an auxiliary platform which is the same

height as the holder (optional accessory) and base of the special auxiliary

equipment.

Capacity: wooden material (W × H × L)

300 mm × 45 mm × 1050 mm, or

180 mm × 25 mm × 1600 mm

18. Installing the holders … (Optional accessory)

The holders help keep longer workpieces stable and in place during the

cutting operation.

(1) As indicated in Fig. 19, use a steel square for aligning the upper edge of the

holders with the base surface.

Loosen the 6 mm wing nut. Turn a height adjustment bolt 6 mm, and adjust

the height of the holder.

(2) After adjustment, firmly tighten the wing nut and fasten the holder with the

6 mm knob bolt (optional accessory). If the length of Height Adjustment Bolt

6 mm is insufficient, spread a thin plate beneath. Make sure the end of Height

Adjustment Bolt 6 mm does not protrude from the holder.

CAUTION

䡬

When transporting or carrying the tool, do not grasp the holder.

䡬

There is the danger of the holder slipping out of the base. Grasp the handle

instead of the holder.

19. Stopper for precision cutting … (Stopper and holder are optional accessory)

The stopper facilitates continuous precision cutting in lengths of 280 mm to

450 mm.

To install the stopper, attach it to the holder with the 6 mm knob bolt as

shown in Fig. 20.

20. Confirmation for use Crown molding vise, Crown molding Stopper (L) and

(R) (Optional accessory)

(1) Crown molding Stopper (L) and (R) (optional accessories) allow easier cuts

of crown molding without tilting the saw blade. lnstall them in the base

both-sides side to be shown in Fig. 21. After inserting

tighten the 6 mm knob bolts to secure the Crown molding Stoppers.

(2) The crown molding vise (B) (Optional accessory) can be mounted on either

the left fence (Fence (B)) or the right fence (Fence (A)). lt can unite with the

slope of the crown molding and vice can be pressed down.

Then turn the upper knob, as necessary, to securely attach the crown molding

in position. To raise or lower the vise assembly, first loosen the 6 mm knob

bolt. After adjusting the height, firmly tighten the 6 mm wing bolt; then

turn the upper knob, as necessary, to securely attach the the crown molding

in position (Fig 22).

Position crown molding with its WALL CONTACT EDGE against the guide

fence and its CEILING CONTACT EDGE against the Crown molding Stoppers

as shown in Fig. 22. Adjust the Crown molding Stoppers according to the

size of the crown molding.

Tighten the 6 mm wing bolt to secure the Crown molding Stoppers.

WARNING

䡬

Always firmly clamp or vise to secure the crown molding to the fence;

otherwise the crown molding might be thrust from the table and cause bodily

harm.

Do not bevel cutting. The main body or saw blade may contact the sub fence,

resulting in an injury.

CAUTION

Always confirm that the motor head (Fig. 1) does not contact the crown

molding vise ass’y when it is lowered for cutting. If there is any danger that

it may do so, loosen the 6mm knob bolt and move the crown molding vise

ass’y to a position where it will not contact the saw blade.

21. Groove cutting procedures

Grooves in the workpiece can be cut by adjusting the 6 mm depth adjustment

bolt (Fig. 23).

(1) Lower the motor head, and turn the 6 mm depth adjustment bolt by hand.

(Where the head of the 6 mm depth adjustment bolt contacts the hinge.)

(2) Adjust to the desired cutting depth by setting the distance between the saw

blade and the surface of the base. (Fig. 24)

NOTE

䡬

When cutting a single groove at either end of the workpiece, remove the

unneeded portion with a chisel.

22. Using the Light (Model C8FSHE Only)

WARNING

䡬

Check to ascertain that the main unit and light are off before plugging the

cord into the power socket.

䡬

The light lens reaches high temperatures during and immediately after use

and should not be touched under any circumstances.

Failure to observe this may result in burns.

CAUTION

䡬

Do not subject the light to strong impact.

Failure to observe this may result in damage to the light or a reduced life

span.

䡬

Only switch the light on when cutting.

䡬

Do not shine the light continuously into the eyes.

Failure to observe this may result in damage to the eyes.

䡬

Wipe all dirt that adheres to the light lens with a soft cloth gently so that the

light is not scratched or damaged.

Scratches on the light lens may result in less luminance.

䡬

The light switch is fitted with an anti-dust cover. Make sure that the switch

cover is not scratched or otherwise damaged.

䡬

There are cases in which shavings may enter the switch and prevent the

light from functioning.

English

(1) Insert the plug on the main unit into a power socket.

(2) Set the light switch into the upper position (ON) to light it, and into the lower

position (OFF) to switch it off. (See Fig. 28)

(3) Move the light fitting to the right and left to adjust the lighting position.

MOUNTING AND DISMOUNTING SAW BLADE

WARNING

To prevent an accident or personal injury, always turn off the trigger switch

and disconnect the power plug from the receptacle before removing or

installing a blade.

1. Mounting the saw blade (Fig. 25, Fig. 26 and Fig. 27)

(1) Use the accessory 10 mm box wrench to loosen the 6 mm bolt fastening the

spindle cover and then rotate the spindle cover.

(2) Press in spindle lock and loosen bolt with 10 mm box wrench.

Since the bolt is left-hand threaded, loosen by turning it to the right.

NOTE

䡬

If the spindle lock cannot be easily pressed in to lock the spindle, turn the

bolt with 10 mm box wrench while applying pressure on the spindle lock.

The saw blade spindle is locked when the spindle lock is pressed inward.

(3) Remove the bolt and washer (D).

(4) Lift the lower guard and mount the saw blade.

WARNING

When mounting the saw blade, confirm that the rotation indicator mark on

the saw blade and the rotation direction of the gear case are properly

matched.

(5) Thoroughly clean washer (D) and the bolt, and install them onto the saw

blade spindle.

(6) Press in the spindle lock and tighten the bolt by turning it to the left by 10

mm box wrench.

(7) Rotate the spindle cover unitl hook in spindle cover is in the original position.

Then tighten the 6mm bolt.

CAUTION

䡬

Confirm that the spindle lock has returned to the retract position after

installing or removing the saw blade.

䡬

Tighten the bolt so it does not come loose during operation.

䡬

Confirm that the bolt has been properly tightened before the power tool is

started.

䡬

Confirm that the lower guard has closed position.

2. Dismounting the saw blade

Dismount the saw blade by reversing the mounting procedures described in

paragraph 1 above.

The saw blade can easily be removed after lifting the lower guard.

CAUTION

䡬

Never attempt to install saw blades except

216 mm in diameter.

MAINTENANCE AND INSPECTION

WARNING

To avoid an accident or personal injury, always confirm the trigger switch is

turned OFF and that the power plug has been disconnected from the

receptacle before performing any maintenance or inspection of this tool.

Report to qualified person as soon as possible, if you discover the fault of

machine including guards or blade saw.

1. Inspecting the saw blade

Always replace the saw blade immediately upon the first sign of deterioration

or damage.

A damaged saw blade can cause personal injury and a worn saw blade can

cause ineffective operation and possible overload to the motor.

CAUTION

Never use a dull saw blade. When a saw blade is dull, its resistance to the

hand pressure applied by the tool handle tends to increase, making it unsafe

to operate the power tool.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that they are properly

tightened. Should any of the screws be loose, re-tighten them immediately.

Failure to do so could result in serious hazard.

3. Inspecting the carbon brushes (Fig. 29)

The motor employs carbon brushes which are consumable parts. Since an

excessively worn carbon brush can result in motor trouble, replace the carbon

brushes with new ones having the same carbon brush No. shown in the

figure when it becomes worn to or near the “wear limit”. In addition, always

keep carbon brushes clean and ensure that they slide freely within the brush

holders.

4. Replacing a carbon brushes

Disassemble the brush cap with a slotted-head screwdriver. The carbon

brushes can then be easily removed.

5. Maintenance of the motor

The motor unit winding is the very “heart” of the power tool. Exercise due

care to ensure the winding does not become damaged and/or wet with oil or

water.

6. Inspecting the lower guard for proper operation

Before each use of the tool, test the lower guard (Fig. 5) to assure that it is in

good condition and that it moves smoothly.

Never use the tool unless the lower guard operates properly and it is in

good mechanical condition.

7. Storage

After operation of the tool has been completed, check that the following has

been performed:

(1) Trigger switch is in OFF position,

(2) Power plug has been removed from the receptacle,

When the tool is not in use, keep it stored in a dry place out of the reach of

children.

8. Lubrication

Lubricate the following sliding surfaces once a month to keep the power

tool in good operating condition for a long time.

Use of machine oil is recommended.

Oil supply points:

* Rotary portion of hinge

* Rotary portion of holder (A)

* Rotary portion of vise assembly

9. Cleaning

Periodically remove chips and other waste material from the surface of the

power tool with a damp, soapy cloth. To avoid a malfunction of the motor,

protect it from contact with oil or water.

(Only Model C8FSHE)

If the laser line becomes invisible due to chips and the like adhered onto the

window of the laser marker's light-emitting section, wipe and clean the window

with a dry cloth or a soft cloth moistened with soapy water, etc.

10. Service parts list

CAUTION

Repair, modification and inspection of HiKOKI Power Tools must be carried฀

out by a HiKOKI Authorized Service Center.

Especially laser device should be maintained by the authorised agent by฀

laser manufacturer.

Always assign the repair of laser device to HiKOKI Authorised Service Center.฀

This Parts List will be helpful if presented with the tool to the HiKOKI฀

Authorized Service Center when requesting repair or other maintenance.฀

In the operation and maintenance of power tools, the safety regulations and฀

standards prescribed in each country must be observed.

MODIFICATIONS

HiKOKI Power Tools are constantly being improved and modified to฀

incorporate the latest technological advancements.

Accordingly, some parts may be changed without prior notice.

English

GUARANTEE

We guarantee HiKOKI Power Tools in accordance with statutory/country specific

regulation. This guarantee does not cover defects or damage due to misuse, abuse,

or normal wear and tear. In case of complaint, please send the Power Tool,

undismantled, with the GUARANTEE CERTIFICATE found at the end of this฀

Handling instruction, to a HiKOKI Authorized Service Center.

NOTE

Due to HiKOKI’s continuing program of research and development the฀

specifications herein are subject to change without prior notice.

Information concerning airborne noise and vibration

The measured values were determined according to EN61029.

The typical A-weighted sound pressure level: 90 dB(A)

The typical A-weighted sound power level: 103 dB (A)

Wear ear protection.

The typical weighted root mean square acceleration value does not exceed 2.5

m/s

Information for power supply system to be used with electric tools provided

with rated voltage 230 V~

Switching operations of electric apparatus cause voltage fluctuations.

The operation of this electric tool under unfavorable mains conditions can have

adverse effects to the operation of other electric apparatus.

With a mains impedance equal or less than 0.29 Ohms there will probably be

no negative effects.

Usually, the maximum permissible mains impedance will not be exceeded

when the branch to the power outlet is fed from a junction box with a service

capacity of 25 ampere or higher.

In case of power failure, or when the power plug is pulled out, immediately return

the switch to OFF position. This prevents an uncontrolled restart.

Stránka sa načítava ...

Hikoki C8FSHE Slide Compound Miter Saw Návod na používanie

Značka: Hikoki

Model: C8FSHE Slide Compound Miter Saw

Kategória: Elektrické náradie

Typ: Návod na používanie

Stiahnite si PDF

správa

Hikoki C8FSHE Slide Compound Miter Saw Návod na používanie

Hikoki C8FSHE Slide Compound Miter Saw Návod na používanie

V iných jazykoch

Súvisiace články

Ďalšie dokumenty