Indesit XWE 81283X W EU Užívateľská príručka

  • Prečítal som si návod na použitie práčky Indesit XWE 81283 a som pripravený odpovedať na vaše otázky. Návod obsahuje informácie o inštalácii, používaní rôznych programov prania vrátane funkcie Push & Wash, údržbe a riešení bežných problémov. Opýtajte sa ma čokoľvek!
  • Ako spustiť rýchly program prania?
    Čo robiť, ak práčka silno vibruje počas odstreďovania?
    Ako vyčistiť čerpadlo práčky?
1
GB
WASHING MACHINE
Instructions for use
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Care and maintenance, 4
Cutting off the water and electricity supplies
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Precautions and tips, 5
General safety
Disposal
Opening the porthole door manually
Description of the washing machine, 6-7
Control panel
Display
Running a wash cycle, 8
Wash cycles and options, 9-10
Table of wash cycles
Wash options
Push & Wash
Detergents and laundry, 11-12
Detergent dispenser drawer
Bleach cycle
Preparing the laundry
Special wash cycles
Load balancing system
Troubleshooting, 13
Service, 14
English,1
GB
XWE 81283
ES
Español,15
UK
Українська,71
PT
Português,29
CZ
Česky,43
BG
Български,57
2
GB
! This instruction manual should be kept in a safe
place for future reference. If the washing machine
is sold, transferred or moved, make sure that the
instruction manual remains with the machine so
that the new owner is able to familiarise himself/
herself with its operation and features.
! Read these instructions carefully: they contain
vital information relating to the safe installation
and operation of the appliance.
Unpacking and levelling
Unpacking
1. Remove the washing machine from its packaging.
2. Make sure that the washing machine has
not been damaged during the transportation
process. If it has been damaged, contact the
retailer and do not proceed any further with the
installation process.
3 . R e m o v e t h e 4
protective screws (used
during transportation)
and the rubber washer
with the corresponding
spacer, located on
the rear part of the
appliance (see figure).
4. Close off the holes using the plastic plugs
provided.
5. Keep all the parts in a safe place: you will need
them again if the washing machine needs to be
moved to another location.
! Packaging materials should not be used as
toys for children.
Levelling
1. Install the washing machine on a flat sturdy
floor, without resting it up against walls, furniture
cabinets or anything else.
2. If the floor is not
p e r f e c t l y l e v e l ,
c o m p e n s a t e f o r
any unevenness by
tightening or loosening
the adjustable front
feet (see figure); the
angle of inclination,
measured in relation
to the worktop, must
not exceed 2°.
Levelling the machine correctly will provide
it with stability, help to avoid vibrations and
excessive noise and prevent it from shifting
while it is operating. If it is placed on carpet or
a rug, adjust the feet in such a way as to allow
a sufficient ventilation space underneath the
washing machine.
Connecting the electricity and
water supplies
Connecting the water inlet hose
1. Connect the supply
pipe by screwing it
to a cold water tap
using a ¾ gas threaded
connection (see figure).
Before performing the
connection, allow the
water to run freely until
it is perfectly clear.
2 . C o n n e c t t h e
i n l e t h o s e t o t h e
washing machine by
screwing it onto the
corresponding water
inlet of the appliance,
which is situated on
the top right-hand side
of the rear part of the
appliance (see figure).
3. Make sure that the hose is not folded over
or bent.
! The water pressure at the tap must fall within
the values indicated in the Technical details table
(see next page).
! If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.
! Never use second-hand hoses.
! Use the ones supplied with the machine.
Installation
3
GB
Connecting the drain hose
Connect the drain
hose, without bending
it, to a drainage duct or
a wall drain located at a
height between 65 and
100 cm from the floor;
alternatively, rest it on
the side of a washbasin
or bathtub, fastening
the duct supplied to
the tap (see figure).
The free end of the
hose should not be
underwater.
! We advise against the use of hose extensions;
if it is absolutely necessary, the extension must
have the same diameter as the original hose and
must not exceed 150 cm in length.
Electrical connections
Before plugging the appliance into the electricity
socket, make sure that:
the socket is earthed and complies with all
applicable laws;
the socket is able to withstand the maximum
power load of the appliance as indicated in the
Technical data table (see opposite);
the power supply voltage falls within the values
indicated in the Technical data table (see
opposite);
the socket is compatible with the plug of
the washing machine. If this is not the case,
replace the socket or the plug.
! The washing machine must not be installed
outdoors, even in covered areas. It is extremely
dangerous to leave the appliance exposed to
rain, storms and other weather conditions.
! When the washing machine has been installed,
the electricity socket must be within easy reach.
! Do not use extension cords or multiple sockets.
! The cable should not be bent or compressed.
! The power supply cable must only be replaced
by authorised technicians.
Warning! The company shall not be held responsible
in the event that these regulations are not respected.
The first wash cycle
Once the appliance has been installed, and before
you use it for the first time, run a wash cycle
with detergent and no laundry, using the wash
cycle “Auto Clean” (see “Cleaning the washing
machine”).
65 - 100 cm
Technical data
Model
XWE 81283
Dimensions
width 59.5 cm
height 85 cm
depth 60.5 cm
Capacity
from 1 to 8 kg
Electrical
connections
please refer to the technical
data plate fixed to the ma-
chine
Water
connections
maximum pressure
1 MPa (10 bar)
minimum pressure
0.05 MPa (0.5 bar)
drum capacity 62 litres
Spin speed
up to 1200 rotations per minute
Test wash
cycles in
accordan-
ce with
directives
1061/2010
and
1015/2010
Programme 8:
Cotton Standard 60°.
Programme 9:
Cotton Standard 40°.
This appliance conforms to
the following EC Directives:
- 2004/108/EC (Electroma-
gnetic Compatibility)
- 2006/95/EC (Low Voltage)
- 2012/19/EU
4
GB
Care and maintenance
Cleaning the pump
The washing machine is fitted with a self-
cleaning pump which does not require any
maintenance. Sometimes, small items (such
as coins or buttons) may fall into the protective
pre-chamber at the base of the pump.
! Make sure the wash cycle has finished and
unplug the appliance.
To access the pre-chamber:
1. Take off the cover
panel on the front
of the machine by
first pressing it in
the centre and then
pushing downwards
on both sides until
you can remove it
(see figures).
2. Unscrew the lid
by rotating it anti-
clockwise (see figure):
a little water may
trickle out. This is
perfectly normal.
3. Clean the inside thoroughly.
4. Screw the lid back on.
5. Reposition the panel, making sure the hooks
are securely in place before you push it onto
the appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If
there are any cracks, it should be replaced
immediately: during the wash cycles, water
pressure is very strong and a cracked hose
could easily split open.
! Never use second-hand hoses.
Cutting off the water and electricity
supplies
Turn off the water tap after every wash cycle.
This will limit wear on the hydraulic system inside
the washing machine and help to prevent leaks.
Unplug the washing machine when cleaning it
and during all maintenance work.
Cleaning the washing machine
• The outer parts and rubber components
of the appliance can be cleaned using a soft
cloth soaked in lukewarm soapy water. Do not
use solvents or abrasives.
• The washing machine has a “Auto Clean”
programme for its internal parts that must be
run with no load in the drum.
For maximum performance you may want
to use either the detergent (i.e. a quantity
10% the quantity specified for lightly-soiled
garments) or special additives to clean the
washing machine. We recommend running a
cleaning programme every 40 wash cycles.
To start the programme press buttons A and
B simultaneously for 5 seconds (see figure).
The programme will start automatically and
will last approximately 70 minutes. To stop the
cycle press the START/PAUSE button.
Cleaning the detergent dispenser
drawer
To remove the drawer,
press lever (1) and pull
the drawer outwards
(2) (see figure).
Wash it under running
water; this procedure
should be repeated
frequently.
Caring for the door and drum of your
appliance
Always leave the porthole door ajar in order to
prevent unpleasant odours from forming.
2
1
1
2
3
A
B
5
GB
Precautions and tips
! This washing machine was designed and constructed
in accordance with international safety regulations. The
following information is provided for safety reasons and
must therefore be read carefully.
General safety
This appliance was designed for domestic use only.
This appliance can be used by children
aged from 8 years and above and
persons with reduced physical, sensory or
mental capabilities or lack of experience
and knowledge if they have been given
supervision or instruction concerning use of
the appliance in a safe way and understand
the hazards involved. Children shall not
play with the appliance. Cleaning and user
maintenance shall not be made by children
without supervision.
The washing machine must only be used by adults, in
accordance with the instructions provided in this manual.
Do not touch the machine when barefoot or with wet or
damp hands or feet.
Do not pull on the power supply cable when unplugging
the appliance from the electricity socket. Hold the plug
and pull.
Do not open the detergent dispenser drawer while the
machine is in operation.
Do not touch the drained water as it may reach
extremely high temperatures.
Never force the porthole door. This could damage the
safety lock mechanism designed to prevent accidental
opening.
If the appliance breaks down, do not under any
circumstances access the internal mechanisms in an
attempt to repair it yourself.
Always keep children well away from the appliance while
it is operating.
The door can become quite hot during the wash cycle.
If the appliance has to be moved, work in a group of two
or three people and handle it with the utmost care. Never
try to do this alone, because the appliance is very heavy.
Before loading laundry into the washing machine, make
sure the drum is empty.
Disposal
Disposing of the packaging materials: observe local
regulations so that the packaging may be re-used.
The European Directive 2012/19/EU on Waste
Electrical and Electronic Equipment, requires that
old household electrical appliances must not be
disposed of in the normal unsorted municipal waste
stream. Old appliances must be collected
separately in order to optimise the recovery and
recycling of the materials they contain and reduce
the impact on human health and the environment.
The crossed out “wheeled bin” symbol on the
product reminds you of your obligation, that when
you dispose of the appliance it must be separately
collected.
Consumers should contact their local authority or
retailer for information concerning the correct
disposal of their old appliance.
Opening the porthole door manually
In the event that it is not possible to open the porthole
door due to a powercut, and if you wish to remove the
laundry, proceed as follows:
1. remove the plug from the
electrical socket.
2. make sure the water level
inside the machine is lower
than the door opening; if
it is not, remove excess
water using the drain hose,
collecting it in a bucket as
indicated in the figure.
3. remove the cover panel
on the lower front part of
the washing machine (see
figure).
4. pull outwards using the tab as indicated in the figure,
until the plastic tie-rod is freed from its stop position; pull
downwards and open the door at the same time.
5. reposition the panel, making sure the hooks are securely
in place before you push it onto the appliance.
20
1
2
3
6
GB
Description of the washing
machine
Control panel
TEMPERATURE
button
WASH
CYCLE
SELECTOR
KNOB
Detergent dispenser drawer
ON/OFF
button
SPIN
button
START/PAUSE
button
and indicator light
DELAYED
START
button
OPTION
buttons
Detergent dispenser drawer: used to dispense
detergents and washing additives (see “Detergents and
laundry”).
ON/OFF button: press this briefly to switch the
machine on or off. The START/PAUSE indicator light which
flashes slowly in a green colour shows that the machine is
switched on. To switch off the washing machine during the
wash cycle, press and hold the button for approximately 3
seconds; if the button is pressed briefly or accidentally the
machine will not switch off.
If the machine is switched off during a wash cycle, this
wash cycle will be cancelled.
PUSH & WASH button: (see “Wash cycles and options”).
WASH CYCLE SELECTOR KNOB: used to set the
desired wash cycle (see “Table of wash cycles”).
OPTION buttons: press to select the available options.
The indicator light corresponding to the selected option will
remain lit.
TEMPERATURE button: press to reduce or
completely exclude the temperature; the value appears on
the display.
SPIN button: press to reduce or completely exclude
the spin cycle; the value appears on the display.
DELAYED START button: press to set a delayed
start for the selected wash cycle; the delay period appears
on the display.
START/PAUSE button and indicator light: when the
green indicator light flashes slowly, press the button to
start a wash cycle. Once the cycle has begun the indicator
light will remain lit in a fixed manner. To pause the wash
cycle, press the button again; the indicator light will flash
in an amber colour. If the symbol is not illuminated, the
door may be opened. To start the wash cycle from the
point at which it was interrupted, press the button again.
Standby mode
This washing machine, in compliance with new energy
saving regulations, is fitted with an automatic standby
system which is enabled after about 30 minutes if no
activity is detected. Press the ON-OFF button briefly and
wait for the machine to start up again.
Consumption in off-mode: 0,5 W
Consumption in Left-on: 8 W
DISPLAY
PUSH & WASH
button
7
GB
The display is useful when programming the machine and provides a great deal of information.
The duration of the available wash cycles and the remaining time of a running cycle appear in section A; if the DELAYED
START option has been set, the countdown to the start of the selected wash cycle will appear.
Pressing the corresponding button allows you to view the maximum spin speed and temperature values attained by the
machine during the set wash cycle, or the values selected most recently, if these are compatible with the set wash cycle.
The hour-glass flashes while the machine processes the data on the basis of the selected programme. After a maximum of
10 minutes, the icon remains lit in a fixed manner and the final amount of time remaining is displayed. The hour-glass icon
will then switch off approximately 1 minute after the final amount of time remaining has appeared.
The “wash cycle phases” corresponding to the selected wash cycle and the “wash cycle phase” of the running wash cycle
appear in section B:
Main wash
Rinse
Spin
Drain
The “delay” symbol , when lit, indicates that the set “delayed start” value has appeared on the display.
There are three levels in section C concerning the washing options.
DOOR LOCKED indicator light:
The lit symbol indicates that the door is locked. To prevent any damage, wait until the symbol turns off before opening the
door.
To open the door while a cycle is in progress, press the START/PAUSE button; if the DOOR LOCKED symbol is switched
off the door may be opened.
Display
B
C
A
C
8
GB
Running a wash cycle
Rapid programming
1. LOAD THE LAUNDRY. Open the porthole door.
Load the laundry, making sure you do not exceed
the maximum load value indicated in the table of
programmes and wash cycles on the following page.
2. ADD THE DETERGENT. Pull out the detergent
dispenser drawer and pour the detergent into the
relevant compartments as described in “Detergents and
laundry”.
3. CLOSE THE DOOR.
4. Press the “PUSH & WASH” button to start the wash
programme.
Traditional programming
1. SWITCH THE MACHINE ON. Press the button;
the START/PAUSE indicator light will flash slowly in a
green colour.
2. LOAD THE LAUNDRY. Open the porthole door.
Load the laundry, making sure you do not exceed
the maximum load value indicated in the table of
programmes and wash cycles on the following page.
3. ADD THE DETERGENT. Pull out the detergent
dispenser drawer and pour the detergent into the relevant
compartments as described inDetergents and laundry”.
4. CLOSE THE DOOR.
5. SELECT THE WASH CYCLE. Use the WASH CYCLE
SELECTOR knob to select the desired wash cycle. A
temperature and spin speed is set for each wash cycle;
these values may be adjusted. The duration of the cycle
will appear on the display.
6. CUSTOMISE THE WASH CYCLE. Use the relevant
buttons:
Modify the temperature and/or spin
speed. The machine automatically displays the
maximum temperature and spin speed values set for
the selected cycle, or the most recently-used settings
if they are compatible with the selected cycle. The
temperature can be decreased by pressing the
button, until the cold wash “OFF” setting is reached.
The spin speed may be progressively reduced by
pressing the button, until it is completely excluded
(the “OFF” setting). If these buttons are pressed again,
the maximum values are restored.
! Exception: if the 8 programme is selected, the
temperature can be increased up to a value of 90°C.
Setting a delayed start.
To set a delayed start for the selected cycle, press the
corresponding button repeatedly until the required delay
period has been reached. When this option has been
activated, the symbol lights up on the display. To
remove the delayed start setting, press the button until
the text “OFF” appears on the display.
Modify the cycle settings.
Press the button to enable the option; the indicator
light corresponding to the button will switch on.
Press the button again to disable the option; the
indicator light will switch off.
! If the selected option is not compatible with the set
wash cycle, the indicator light will flash and the option
will not be activated.
! If the selected option is not compatible with another
previously selected option, the indicator light will
flash accompanied by a buzzer (3 beeps), and only
the latter option will be activated; the indicator light
corresponding to the activated option will turn on.
! The options may affect the recommended load value
and/or the duration of the cycle.
7. START THE WASH CYCLE. Press the START/
PAUSE button. The corresponding indicator light will
turn green, remaining lit in a fixed manner, and the door
will be locked (the DOOR LOCKED symbol will be lit).
To change a wash cycle while it is in progress, pause
the washing machine using the START/PAUSE button
(the START/PAUSE indicator light will flash slowly in an
amber colour); then select the desired cycle and press
the START/PAUSE button again.
To open the door while a cycle is in progress, press
the START/PAUSE button; if the DOOR LOCKED
symbol is switched off the door may be opened. Press
the START/PAUSE button again to restart the wash
cycle from the point at which it was interrupted.
8. THE END OF THE WASH CYCLE. This will be
indicated by the text “END” on the display; when the
DOOR LOCKED symbol switches off the door may
be opened. Open the door, unload the laundry and
switch off the machine.
! If you wish to cancel a cycle which has already begun,
press and hold the button. The cycle will be stopped
and the machine will switch off.
9
GB
Wash cycles and options
Table of wash cycles
Wash options
Rapid
When this button is pressed the first time, the 9’ icon will
light up, when pressed the second time the 30’ icon lights
up and the third time the 1h icon lights up. When pressed
the fourth time the 9’ icon lights up again.
! It cannot be used in conjunction with wash cycles 1-2-3-
4-5-6-7-8-9-10-11-12-13- - .
Fast Forward
During a wash programme and under certain conditions,
pressing this button allows for ending the wash
programme after only 20’ if necessary, by performing a
brief rinse cycle followed by a spin cycle at maximum 800
rpm or lower, if reduced manually during the programme
customisation phase. In this case, washing and rinsing
performance will be reduced. After pressing the button, the
relative indicator light turns on together with the indicator
light of the rinse phase. If the selected temperature is
equal to 40° and/or the button is pressed during the initial
phase of the programme, the “Fast Forward” option lasts
longer so that the detergent can dissolve properly and
avoid damaging the fabrics. In this case, the rinse phase
indicator light flashes while the wash indicator light remains
fixed until the necessary activation conditions are fulfilled.
If less than 20’ remain of the wash programme, the option
will be disabled.
! It cannot be used in conjunction with wash cycles 2-4-5-
6-14- - .
Stain removal
This option allows for selecting the type of dirt so as to
optimally adjust the cycle for removing the stains. The
following types of dirt can be selected:
- Food, for stains caused by foodstuffs and beverages,
for example.
- Work, for grease and ink stains, for example.
- Outdoor, for mud and grass stains, for example.
! The wash cycle duration varies according to the type of
selected dirt.
! It cannot be used in conjunction with wash cycles 1-2-3-
4-5-6-7-11-12-13-14- - .
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary accor-
ding to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.
1) Test wash cycle in compliance with directive 1061/2010: set wash cycle 8 with a temperature of 60°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should
be used for garments which can be washed at 60°C. The actual washing temperature may differ from the indicated value.
2) Test wash cycle in compliance with directive 1061/2010: set wash cycle 9 with a temperature of 40°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should
be used for garments which can be washed at 40°C. The actual washing temperature may differ from the indicated value.
For all Test Institutes:
2) Long wash cycle for cottons: set wash cycle 9 with a temperature of 40°C.
3) Synthetic program along: set wash cycle 10 with a temperature of 40°C.
Wash cycles
Description of the wash cycle
Max.
temp.
C)
Max.
speed
(rpm)
Detergents
Max. load (kg)
Residual
dampness %
Energy
consumption
kWh
Total water lt
Cycle duration
Prewash
Wash
Fabric
softener
Bleach
Special
1
Sport
30° 600 -
- 4 - - - 60’
2
Dark
30° 800 -
- 5 - - - 80’
3
Anti-odour (Cotton) 60° 1000 -
- 3,5 - - - 120’
3
Anti-odour (Synthetic) 40° 1000 -
- 3,5 - - - 105’
4
Delicate
30° 0 -
- 1 - - - 80’
5
Wool: for wool, cashmere, etc. 40° 800 -
- 2 - - - 85’
6
Duvet: for down-stuffed garments. 30° 1000 -
- 3,5 - - - 100’
Standard
7
Cottons with Pre-wash: extremely soiled whites. 90° 1200
- 8 53 2,80 105 210’
8
Cotton Standard 60° (1): heavily soiled whites and resistant colours.
60°
(Max. 90°)
1200 -
- 8 53 1,04 55 215’
9
Cotton Standard 40° (2): lightly soiled whites and delicate colours.
40° 1200 -
- 8 53 0,87 81 185’
10
Synthetic: heavily soiled resistant colours. 60° 800 -
- 4,5 46 0,86 47 115’
10
Synthetic (3): lightly soiled resistant colours. 40° 800 -
- 4,5 46 0,60 51 105’
11
Coloured
40° 1200 -
- 8 53 0,89 80 105’
Eco & Rapid
12
Cotton Standard 20°: lightly soiled whites and delicate colours. 20° 1200 -
- 8 - - - 185’
13
Eco Synthetic
20° 800 -
- 8 - - - 120’
14
Rapid
- 800 - -
- 1,5 - - - 9’
14
Rapid
30° 800 -
- 3,5 80 0,18 43 30
14
Rapid
60° 1000 -
- 8 - - - 60’
Partials
Rinse/Bleach - 1200 - -
8 - - - 55
Spin + Drain - 1200 - - - - 8 - - - 25’
10
GB
Push & Wash
This function allows for starting a wash cycle even when the machine is switched off without having to press the ON/OFF
button in advance, or after switching on the machine, without having activated any button and/or selector (otherwise, the
Push & Wash function will be deactivated). To start the Push & Wash cycle press and hold the relative button for 2 seconds.
The lit indicator light indicates that the cycle has started. This wash cycle is ideal for cotton or synthetic fabrics, as it washes
at a temperature of 30° and a maximum spin speed of 1200 rpm. Maximum load 4 kg. (Cycle duration 50’).
How does it work?
1. Load the laundry (cotton and/or synthetic garments) and close the door.
2. Pour the detergent and additives.
3. Start the programme by pressing and holding the Push & Wash button for 2 seconds. The relative indicator light turns
green and the door will lock (the DOOR LOCKED symbol turns on).
N.B.: starting the wash cycle through the Push & Wash button activates an automatic non-customisable cycle
recommended for cotton and synthetic fabrics. This programme does not allow for setting any additional options.
To open the door while an automatic cycle is under way, press the START/PAUSE button; if the DOOR LOCKED symbol
is switched off the door may be opened. Press the START/PAUSE button again to restart the wash cycle from the point at
which it was interrupted.
4. Once the programme is finished, the END indicator light turns on.
11
GB
Detergents and laundry
Detergent dispenser drawer
Successful washing results also depend on the correct
dose of detergent: adding too much detergent will not
necessarily result in a more efficient wash, and may in
fact cause build up on the inside of your appliance and
contribute to environmental pollution.
! Do not use hand washing detergents because these
create too much foam.
! Use powder detergent for white cotton garments, for pre-
washing, and for washing at temperatures over 60°C.
! Follow the instructions given on the detergent packaging.
Open the detergent
dispenser drawer and pour
in the detergent or washing
additive, as follows.
Compartment 1: Pre-wash detergent (powder)
Before pouring in the detergent, make sure that extra
compartment 4 has been removed.
Compartment 2: Washing detergent (powder or liquid)
If liquid detergent is used, it is recommended that the
removable plastic partition A (supplied) be used for proper
dosage. If powder detergent is used, place the partition
into slot B.
Compartment 3: Additives (fabric softeners, etc.)
The fabric softener must not exceed the “max” level indicated
on the central pin.
Extra compartment 4: Bleach
Bleach cycle
Insert the additional compartment 4 (provided) into
compartment 1. In pouring the bleach do not exceed the
max” level indicated on the central pin.
Perform bleaching by pouring the bleach into additional
compartment 4 and set the programme .
! Traditional bleach should be used on resistant white
fabrics, and delicate bleach for coloured and synthetics
fabrics and for wool.
Preparing the laundry
Divide the laundry according to:
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from whites.
Empty all garment pockets and check the buttons.
Do not exceed the values listed in the “Table of wash
cycles”, which refer to the weight of the laundry when dry.
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1.200 g
1 towel 150-250 g
Special wash cycles
Sport (programme 1) is designed for washing lightly soiled
sports clothing (tracksuits, shorts, etc.); for best results, we
recommend not exceeding the maximum load indicated
in the “Table of wash cycles”. We recommend using liquid
detergent, and adding the amount suitable for a half-load.
Dark: use programme 2 to wash dark-coloured garments.
This programme is designed to maintain dark colours over
time. We recommend using a liquid detergent for the best
results when washing dark-coloured garments.
Anti-odour: use programme 3 for washing garments
with bad odours (e.g. smoke, sweat, fried food). The
programme is designed to remove bad odours while
preserving the fabric fibres. Synthetics fabrics or mixed
loads should be washed at 40°, and resistant cotton
fabrics at 60°.
Delicate: use programme 4 to wash very delicate
garments. It is advisable to turn the garments inside out
before washing them. For best results, use liquid detergent
on delicate garments.
Wool: the wool wash programme of this machine has
been tested and approved by The Woolmark Company
for the washing of wool containing garments labelled as
“hand wash” provided that the garments are washed
according to the instructions on the garment label and
those issued by the manufacturer of this washing machine.
(M1127)
In UK, Eire, Hong Kong and India the Woolmark trade mark
is a Certification trade mark.
Duvet: to wash double or single duvets (the weight of
which should not exceed 3,5 kg), cushions or clothes
padded with goose down such as puffa jackets, use the
special wash programme number 6. We recommend that
duvets are placed in the drum with their edges folded
inwards (see figure) and that no more than ¾ of the total
volume of the drum is used. To achieve the best results,
we recommend that a liquid detergent is used and placed
inside the detergent dispenser drawer.
Coloured: use this programme 11 to wash bright
coloured clothes. The programme is designed to maintain
bright colours over time.
1
2
3
4
A
B
12
GB
Cotton Standard 20° (programme 12) ideal for lightly
soiled cotton loads. The effective performance levels
achieved at cold temperatures, which are comparable to
washing at 40°, are guaranteed by a mechanical action
which operates at varying speed, with repeated and
frequent peaks.
Eco Synthetic (programme 13) ideal for mixed loads
(cotton and synthetics) with a normal soil level. The
effective performance levels achieved at cold temperatures
are guaranteed by a mechanical action which operates at
varying speed, across set average intervals.
Rapid (programme 14) allows for varying the garment
treatment duration from 9’ to 1h. Pressing the
corresponding “Rapid” button allows for varying the cycle
duration between 9’ (refresh), 30’ (wash), 1h (wash).
The 9’ cycle refreshes garments using fabric softener
only; it is advisable not to add any detergent into
the machine. The 30’ programme is designed to wash
lightly soiled garments at 30° (excluding wool and silk)
with a 3 kg maximum load in a short time: it only lasts 30
minutes and allows for saving time and energy. The “1h”
cycle is designed to wash moderately soiled resistant
cotton garments at 60° in an hour, with good washing
performance. For synthetic or mixed garments, we
recommend lowering the temperature down to 40°.
Load balancing system
Before every spin cycle, to avoid excessive vibrations
before every spin and to distribute the load in a uniform
manner, the drum rotates continuously at a speed which
is slightly greater than the washing rotation speed. If,
after several attempts, the load is not balanced correctly,
the machine spins at a reduced spin speed. If the load is
excessively unbalanced, the washing machine performs
the distribution process instead of spinning. To encourage
improved load distribution and balance, we recommend
small and large garments are mixed in the load.
13
GB
Troubleshooting
Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Service (see “ Service”),
make sure that the problem cannot be solved easily using the following list.
Problem:
The washing machine does not
switch on.
The wash cycle does not start.
The washing machine does not fill
with water (the text “H2O” on the
display).
The washing machine
continuously takes in and drains
water.
The washing machine does not
drain or spin.
The washing machine vibrates a
lot during the spin cycle.
The washing machine leaks.
Theoption and START/PAUSE
indicator lights flash rapidly and an
error code appears on the display
(e.g.: F-01, F-..).
There is too much foam.
Push & Wash does not activate.
The programme lasts a lot less
that expected.
Possible causes / Solutions:
The appliance is not plugged into the socket fully, or not enough to make contact.
There is no power in the house.
The washing machine door is not closed properly.
The ON/OFF button has not been pressed.
The START/PAUSE button has not been pressed.
The water tap has not been opened.
A delayed start has been set.
The water inlet hose is not connected to the tap.
The hose is bent.
The water tap has not been opened.
There is no water supply in the house.
The pressure is too low.
The START/PAUSE button has not been pressed.
The drain hose is not fitted at a height between 65 and 100 cm from the floor
(see “Installation”).
The free end of the hose is under water (see “Installation”).
The wall drainage system is not fitted with a breather pipe.
If the problem persists even after these checks, turn off the water tap, switch the
appliance off and contact the Technical Assistance Service. If the dwelling is on one
of the upper floors of a building, there may be problems relating to water drainage,
causing the washing machine to fill with water and drain continuously. Special anti-
draining valves are available in shops and help to prevent this inconvenience.
The wash cycle does not include draining: some cycles require the draining
process to be enabled manually.
The drain hose is bent (see “Installation”).
The drainage duct is clogged.
The drum was not unlocked correctly during installation (see “Installation”).
The washing machine is not level (see “Installation”).
The washing machine is trapped between cabinets and walls (see “Installation”).
The water inlet hose is not screwed on properly (see “Installation”).
The detergent dispenser drawer is blocked (for cleaning instructions, see “Care
and maintenance”).
The drain hose is not fixed properly (see “Installation”).
Switch off the machine and unplug it, wait for approximately 1 minute and then
switch it back on again.
If the problem persists, contact the Technical Assistance Service.
The detergent is not suitable for machine washing (it should display the text “for
washing machines” or “hand and machine wash”, or the like).
Too much detergent was used.
After switching on the machine a control other than Push & Wash was activated.
Switch the machine off and press the Push & Wash button.
The “Fast Forward” option was activated.
14
GB
Service
Before contacting the Technical Assistance Service:
Check whether you can solve the problem alone (seeTroubleshooting”).
Restart the wash cycle to check whether the problem has been solved.
If this is not the case, contact an authorised Technical Assistance Centre.
! Always request the assistance of authorised technicians.
Have the following information to hand:
the type of problem;
the appliance model (Mod.);
the serial number (S/N).
This information can be found on the data plate applied to the rear of the washing machine, and can also be found on the
front of the appliance by opening the door.
ES
15
LAVADORA
Sumario
Instalación, 16-17
Desembalaje y nivelación
Conexiones hidráulicas y eléctricas
Primer ciclo de lavado
Datos técnicos
Mantenimiento y cuidados, 18
Interrumpir el agua y la corriente eléctrica
Limpiar la lavadora
Limpiar el contenedor de detergentes
Cuidar la puerta y el cesto
Limpiar la bomba
Controlar el tubo de alimentación de agua
Precauciones y consejos, 19
Seguridad general
Eliminación
Apertura manual de la puerta
Descripción de la lavadora, 20-21
Panel de control
Pantalla
mo efectuar un ciclo de lavado, 22
Programas y opciones, 23-24
Tabla de programas
Opciones de lavado
Push & Wash
Detergentes y ropa, 25-26
Contenedor de detergentes
Ciclo de blanqueo
Preparar la ropa
Programas particulares
Sistema de equilibrado de la carga
Anomalías y soluciones, 27
Asistencia Técnica, 28
Manual de instrucciones
Español
ES
XWE 81283
16
ES
Instalación
! Es importante conservar este manual para
poder consultarlo en cualquier momento.
En caso de venta, de cesión o de traslado,
verifique que permanezca junto con la
lavadora para informar al nuevo propietario
sobre el funcionamiento y brindar las
correspondientes advertencias.
! Lea atentamente las instrucciones: ellas
contienen importante información sobre la
instalación, el uso y la seguridad.
Desembalaje y nivelación
Desembalaje
1. Desembale la lavadora.
2. Controle que la lavadora no haya sufrido
daños durante el transporte. Si estuviera
dañada no la conecte y llame al revendedor.
3. Quite los 4 tornillos
de protección
para el transporte
y la arandela
de goma con el
correspondiente
distanciador ubicados
en la parte posterior
(ver la figura).
4. Cubra los orificios con los tapones de
plástico suministrados con el aparato.
5. Conserve todas las piezas: cuando la
lavadora deba ser transportada nuevamente,
deberán volver a colocarse.
! Los embalajes no son juguetes para los
niños.
Nivelación
1. Instale la lavadora sobre un piso plano y
rígido, sin apoyarla en las paredes, muebles ni
en ningún otro aparato.
2. Si el piso no
está perfectamente
horizontal, compense
las irregularidades
desenroscando o
enroscando las patas
delanteras (ver la
figura); el ángulo de
inclinación medido
sobre la superficie
de trabajo, no debe
superar los 2º.
Una cuidadosa nivelación brinda estabilidad
a la máquina y evita vibraciones, ruidos y
desplazamientos durante el funcionamiento.
Cuando se instala sobre moquetas o
alfombras, regule los pies para conservar
debajo de la lavadora un espacio suficiente
para la ventilación.
Conexiones hidráulicas y
eléctricas
Conexión del tubo de alimentación de
agua
1. Conectar el tubo
de tubo enroscándolo
a un grifo de agua fría
con la boca roscada
de 3/4 gas (ver la
figura).
Antes de conectarlo,
haga correr el agua
hasta que esté
límpida.
2. Conecte el tubo
de alimentación
a la lavadora
enroscándolo en
la toma de agua
correspondiente
ubicada en la parte
posterior derecha
(arriba) (ver la figura).
3. Controle que en el tubo no hayan pliegues
ni estrangulaciones.
! La presión de agua del grifo debe estar
comprendida dentro de los valores contenidos
en la tabla de Datos técnicos (ver la página
correspondiente).
! Si la longitud del tubo de alimentación
no es la suficiente, diríjase a un negocio
especializado o a un técnico autorizado.
! No utilice nunca tubos ya usados.
! Utilice los suministrados con la máquina.
ES
17
Conexión del tubo de desagüe
Conecte el tubo de
desagüe, sin plegarlo,
a un conducto de
desagüe o a una
desagüe de pared
ubicados a una
distancia del piso
comprendida entre
65 y 100 cm.;
o apóyelo en
el borde de un
lavamanos o de una
bañera, uniendo la
guía suministrada
con el aparato, al
grifo (ver la figura).
El extremo libre del
tubo de desagüe no
debe permanecer
sumergido en el
agua.
! No se aconseja utilizar tubos de
prolongación, si fuera indispensable hacerlo,
la prolongación debe tener el mismo diámetro
del tubo original y no superar los 150 cm.
Conexión eléctrica
Antes de enchufar el aparato, verifique que:
la toma tenga la conexión a tierra y haya
sido hecha según las normas legales;
la toma sea capaz de soportar la carga
xima de potencia de la máquina indicada
en la tabla de Datos técnicos (ver al costado);
la tensión de alimentación esté comprendida
dentro de los valores indicados en la tabla
de Datos técnicos (ver al costado);
la toma sea compatible con el enchufe de la
lavadora. Si no es así, sustituya la toma o el
enchufe.
! La lavadora no debe ser instalada al aire
libre, ni siquiera si el lugar está reparado, ya
que es muy peligroso dejarla expuesta a la
lluvia o a las tormentas.
! Una vez instalada la lavadora, la toma de
corriente debe ser fácilmente accesible.
! No utilice prolongaciones ni conexiones
múltiples.
65 - 100 cm
! El cable no debe estar plegado ni sufrir
compresiones.
! El cable de alimentación debe ser sustituido
sólo por técnicos autorizados.
¡Atención! La empresa fabricante declina toda
responsabilidad en caso de que estas normas
no sean respetadas.
Primer ciclo de lavado
Después de la instalación y antes del uso,
realice un ciclo de lavado con detergente y
sin ropa, seleccionando el programa “Auto
Limpieza” (ver “Limpiar la lavadora”).
Datos técnicos
Modelo
XWE 81283
Dimensio-
nes
ancho 59.5 cm
altura 85 cm
profundidad 60,5 cm
Capacidad
de 1 a 8 kg
Conexiones
eléctricas
ver la placa de característi-
cas técnicas aplicada en la
máquina
Conexiones
hídricas
presión máxima
1 MPa (10 bar)
presión mínima
0,05 MPa (0,5 bar)
capacidad del cesto 62 litros
Velocidad
de centrifu-
gado
máxima 1200 r.p.m.
Programas
de control
según las
directivas
1061/2010 y
1015/2010
programa 8;
Algodón Standard 60ºC.
programa 9;
Algodón Standard 40ºC.
Esta máquina cumple con lo
establecido por las siguientes
Directivas de la Comunidad:
- 2004/108/CE (Compatibili-
dad Electromagnética)
- 2012/19/EU
- 2006/95/CE (Baja Tensión)
18
ES
Limpiar la bomba
La lavadora posee una bomba autolimpiante
que no necesita mantenimiento. Pero puede
suceder que objetos pequeños (monedas,
botones) caigan en la precámara que protege
la bomba, situada en la parte inferior de la
misma.
! Verifique que el ciclo de lavado haya
terminado y desenchufe la máquina.
Para acceder a la precámara:
1. quite el panel de
cobertura delantero
de la máquina
presionando hacia el
centro, luego empuje
hacia abajo desde
ambos costados y
extráigalo (ver las
figuras).
2. desenrosque la
tapa girándola en
sentido antihorario
(ver la figura): es
normal que se
vuelque un poco de
agua;
3. limpie con cuidado el interior;
4. vuelva a enroscar la tapa;
5. vuelva a montar el panel verificando,
antes de empujarlo hacia la máquina, que
los ganchos se hayan introducido en las
correspondientes ranuras.
Controlar el tubo de alimentación
de agua
Controle el tubo de alimentación al menos
una vez al año. Si presenta grietas o rajaduras
debe ser sustituido: durante los lavados, las
fuertes presiones podrían provocar roturas
imprevistas.
! No utilice nunca tubos ya usados.
Mantenimiento y cuidados
Interrumpir el agua y la corriente
eléctrica
Cierre el grifo de agua después de cada lavado.
De este modo se limita el desgaste de la
instalación hidráulica de la lavadora y se
elimina el peligro de pérdidas.
Desenchufe la máquina cuando la
debe limpiar y durante los trabajos de
mantenimiento.
Limpiar la lavadora
• La parte externa y las partes de goma
se pueden limpiar con un paño embebido
en agua tibia y jabón. No use solventes ni
productos abrasivos.
• La lavadora posee un programa de “Auto
Limpieza” de su interior que se debe realizar
sin ningún tipo de carga en el cesto.
El detergente (en un 10% de la cantidad
aconsejada para prendas poco sucias)
o algunos aditivos específicos para la
limpieza de la ropa se podrán utilizar como
coadyuvantes en el programa de lavado. Se
aconseja efectuar el programa de limpieza
cada 40 ciclos de lavado.
Para activar el programa pulse simultáneamente
los botones A y B durante 5 segundos
(ver la figura). El programa comenzará
autoticamente y tend una duracn de 70
minutos aproximadamente. Para detener el ciclo
presione el bon START/PAUSE.
Limpiar el cajón de detergentes
Para extraer el cajón,
presione la palanca (1)
y tire hacia afuera (2)
(ver la figura).
Lávelo debajo del agua
corriente, esta limpieza
se debe realizar
frecuentemente.
Cuidar la puerta y el cesto
Deje siempre semicerrada la puerta para
evitar que se formen malos olores.
1
2
3
2
1
A
B
ES
19
Precauciones y consejos
! La lavadora fue proyectada y fabricada en conformidad
con las normas internacionales de seguridad. Estas
advertencias se suministran por razones de seguridad y
deben ser leídas atentamente.
Seguridad general
Este aparato ha sido fabricado para un uso de tipo
doméstico exclusivamente.
Este aparato puede ser utilizado por
niños de 8 años o más y por personas
con capacidades físicas, sensoriales o
mentales disminuidas o con experiencia y
conocimientos insuficientes siempre que
sean supervisados o que hayan recibido
una adecuada formación sobre el uso
del aparato en forma segura y conozcan
los peligros derivados del mismo. Los
niños no deben jugar con el aparato. El
mantenimiento y la limpieza no deben ser
realizados por niños sin supervisión.
La lavadora debe ser utilizada sólo por personas
adultas y siguiendo las instrucciones contenidas en este
manual.
No toque la máquina con los pies desnudos ni con las
manos o los pies mojados o húmedos.
No desenchufe la máquina tirando el cable, sino
tomando el enchufe.
No abra el cajón de detergentes mientras la máquina
está en funcionamiento.
No toque el agua de descarga ya que puede alcanzar
temperaturas elevadas.
En ningún caso fuerce la puerta: podría dañarse el
mecanismo de seguridad que la protege de aperturas
accidentales.
En caso de avería, no acceda nunca a los mecanismos
internos para intentar una reparación.
Controle siempre que los niños no se acerquen a la
máquina cuando está en funcionamiento.
Durante el lavado, la puerta tiende a calentarse.
Si debe ser trasladada, deberán intervenir dos o más
personas, procediendo con el máximo cuidado. La
máquina no debe ser desplazada nunca por una sola
persona ya que es muy pesada.
Antes de introducir la ropa controle que el cesto esté
vacío.
Eliminaciones
Eliminación del material de embalaje:
respete las normas locales, de ese modo, los embalajes
podrán volver a ser utilizados.
La norma Europea 2012/19/EU sobre la eliminación
de aparatos eléctricos y electrónicos, indica que los
electrodomésticos no deben ser eliminados de la
misma manera que los desechos sólidos urbanos. Los
aparatos en desuso se deben recoger separadamente
para optimizar el porcentaje de recuperación y
reciclaje de los materiales que los componen e impedir
potenciales daños para la salud y el medio ambiente. El
símbolo de la papelera tachada se encuentra en todos
los productos para recordar la obligación de recolección
separada.
Para mayor información sobre la correcta eliminación de
los electrodomésticos, los poseedores de los mismos
podrán dirigirse al servicio público responsable o a los
revendedores.
Apertura manual de la puerta
Si falta la energía eléctrica es posible abrir la puerta para
descargar la ropa del siguiente modo:
1. desenchufe la máquina.
2. verifique que el nivel
de agua en el interior de
la máquina sea inferior al
hueco de la puerta; si no
es así, extraiga el agua en
exceso utilizando el tubo de
descarga y recogiéndola en
un balde como se indica en
la figura.
3. quite el panel de cobertura
delantero de la lavadora (ver
la página siguiente).
4. utilizando la lengüeta indicada en la figura, tire hacia
fuera hasta liberar la varilla de plástico del retén; tire
posteriormente hacia abajo hasta sentir un breve sonido
que indica que la puerta está desbloqueada.
5. vuelva a montar el panel verificando, antes de empujarlo
hacia la máquina, que los ganchos se hayan introducido
en las correspondientes ranuras.
20
1
2
3
20
ES
Descripción de la lavadora
Panel de control
Botón
TEMPERATURA
MANDO DE
PROGRAMAS
Cajón de detergentes
Botón ON/OFF
Botón de
CENTRIFUGADO
Botón y piloto
START/PAUSE
PANTALLA
Botón
COMIENZO
RETRASADO
Botones
OPCIÓN
Cajón de detergentes: para cargar detergentes y
aditivos (ver “Detergentes y ropa”).
Botón ON/OFF : presione brevemente el botón
para encender o apagar la máquina. El piloto START/
PAUSE que centellea lentamente en color verde indica
que la máquina está encendida. Para apagar la lavadora
durante el lavado, es necesario mantener presionado el
botón durante más tiempo, aproximadamente 3 seg.; si
se presiona en forma más breve o accidental, la máquina
no se apagará. Si la máquina se apaga durante un lavado
en curso, dicho lavado se anulará.
Botón PUSH & WASH: (ver “Programas y opciones”).
MANDO DE PROGRAMAS: para seleccionar el
programa deseado (ver “Tabla de programas”).
Botones OPCIÓN: para seleccionar las opciones
disponibles. El piloto correspondiente a la opción
seleccionada permanecerá encendido.
Botón CENTRIFUGADO : presiónelo para disminuir
o excluir totalmente el centrifugado; el valor se indica en
la pantalla.
Botón TEMPERATURA : presiónelo para disminuir o
excluir la temperatura; el valor se indica en la pantalla.
Botón COMIENZO RETRASADO : presiónelo
para seleccionar un comienzo retrasado del programa
previamente elegido; el retraso se indica en la pantalla.
Botón y piloto START/PAUSE : cuando el piloto verde
centellea lentamente, presione el botón para que comience
el lavado. Una vez que el ciclo ha comenzado, el piloto
se mantiene fijo. Para poner en pausa el lavado, presione
nuevamente el botón; el piloto centelleará de color ámbar.
Si el símbolo no está iluminado, se podrá abrir la puerta.
Para que el lavado se reanude a partir del momento en el
cual fue interrumpido, presione nuevamente el botón.
Modalidad de stand by
Esta lavadora está en conformidad con las nuevas
normativas vinculadas al ahorro energético. Está
dotada de un sistema de auto-apagado (stand by)
que, en caso de no funcionamiento, se activa pasados
aproximadamente 30 minutos. Presionar brevemente el
botón ON/OFF y esperar que la máquina se active.
Consumo en off-mode: 0,5 W
Consumo en Left-on: 8 W
Botón
PUSH & WASH
/