Indesit XWE 81283X W EU Užívateľská príručka

Značka: Indesit

Model: XWE 81283X W EU

Kategória: Práčky

Typ: Užívateľská príručka

WASHING MACHINE

Instructions for use

Contents

Installation, 2-3

Unpacking and levelling

Connecting the electricity and water supplies

The first wash cycle

Technical data

Care and maintenance, 4

Cutting off the water and electricity supplies

Cleaning the washing machine

Cleaning the detergent dispenser drawer

Caring for the door and drum of your appliance

Cleaning the pump

Checking the water inlet hose

Precautions and tips, 5

General safety

Disposal

Opening the porthole door manually

Description of the washing machine, 6-7

Control panel

Display

Running a wash cycle, 8

Wash cycles and options, 9-10

Table of wash cycles

Wash options

Push & Wash

Detergents and laundry, 11-12

Detergent dispenser drawer

Bleach cycle

Preparing the laundry

Special wash cycles

Load balancing system

Troubleshooting, 13

Service, 14

English,1

XWE 81283

Español,15

Українська,71

Português,29

Česky,43

Български,57

! This instruction manual should be kept in a safe

place for future reference. If the washing machine

is sold, transferred or moved, make sure that the

instruction manual remains with the machine so

that the new owner is able to familiarise himself/

herself with its operation and features.

! Read these instructions carefully: they contain

vital information relating to the safe installation

and operation of the appliance.

Unpacking and levelling

Unpacking

1. Remove the washing machine from its packaging.

2. Make sure that the washing machine has

not been damaged during the transportation

process. If it has been damaged, contact the

retailer and do not proceed any further with the

installation process.

3 . R e m o v e t h e 4

protective screws (used

during transportation)

and the rubber washer

with the corresponding

spacer, located on

the rear part of the

appliance (see figure).

4. Close off the holes using the plastic plugs

provided.

5. Keep all the parts in a safe place: you will need

them again if the washing machine needs to be

moved to another location.

! Packaging materials should not be used as

toys for children.

Levelling

1. Install the washing machine on a flat sturdy

floor, without resting it up against walls, furniture

cabinets or anything else.

2. If the floor is not

p e r f e c t l y l e v e l ,

c o m p e n s a t e f o r

any unevenness by

tightening or loosening

the adjustable front

feet (see figure); the

angle of inclination,

measured in relation

to the worktop, must

not exceed 2°.

Levelling the machine correctly will provide

it with stability, help to avoid vibrations and

excessive noise and prevent it from shifting

while it is operating. If it is placed on carpet or

a rug, adjust the feet in such a way as to allow

a sufficient ventilation space underneath the

washing machine.

Connecting the electricity and

water supplies

Connecting the water inlet hose

1. Connect the supply

pipe by screwing it

to a cold water tap

using a ¾ gas threaded

connection (see figure).

Before performing the

connection, allow the

water to run freely until

it is perfectly clear.

2 . C o n n e c t t h e

i n l e t h o s e t o t h e

washing machine by

screwing it onto the

corresponding water

inlet of the appliance,

which is situated on

the top right-hand side

of the rear part of the

appliance (see figure).

3. Make sure that the hose is not folded over

or bent.

! The water pressure at the tap must fall within

the values indicated in the Technical details table

(see next page).

! If the inlet hose is not long enough, contact a

specialised shop or an authorised technician.

! Never use second-hand hoses.

! Use the ones supplied with the machine.

Installation

Connecting the drain hose

Connect the drain

hose, without bending

it, to a drainage duct or

a wall drain located at a

height between 65 and

100 cm from the floor;

alternatively, rest it on

the side of a washbasin

or bathtub, fastening

the duct supplied to

the tap (see figure).

The free end of the

hose should not be

underwater.

! We advise against the use of hose extensions;

if it is absolutely necessary, the extension must

have the same diameter as the original hose and

must not exceed 150 cm in length.

Electrical connections

Before plugging the appliance into the electricity

socket, make sure that:

• the socket is earthed and complies with all

applicable laws;

• the socket is able to withstand the maximum

power load of the appliance as indicated in the

Technical data table (see opposite);

• the power supply voltage falls within the values

indicated in the Technical data table (see

opposite);

• the socket is compatible with the plug of

the washing machine. If this is not the case,

replace the socket or the plug.

! The washing machine must not be installed

outdoors, even in covered areas. It is extremely

dangerous to leave the appliance exposed to

rain, storms and other weather conditions.

! When the washing machine has been installed,

the electricity socket must be within easy reach.

! Do not use extension cords or multiple sockets.

! The cable should not be bent or compressed.

! The power supply cable must only be replaced

by authorised technicians.

Warning! The company shall not be held responsible

in the event that these regulations are not respected.

The first wash cycle

Once the appliance has been installed, and before

you use it for the first time, run a wash cycle

with detergent and no laundry, using the wash

cycle “Auto Clean” (see “Cleaning the washing

machine”).

65 - 100 cm

Technical data

Model

XWE 81283

Dimensions

width 59.5 cm

height 85 cm

depth 60.5 cm

Capacity

from 1 to 8 kg

Electrical

connections

please refer to the technical

data plate fixed to the ma-

chine

Water

connections

maximum pressure

1 MPa (10 bar)

minimum pressure

0.05 MPa (0.5 bar)

drum capacity 62 litres

Spin speed

up to 1200 rotations per minute

Test wash

cycles in

accordan-

ce with

directives

1061/2010

and

1015/2010

Programme 8:

Cotton Standard 60°.

Programme 9:

Cotton Standard 40°.

This appliance conforms to

the following EC Directives:

- 2004/108/EC (Electroma-

gnetic Compatibility)

- 2006/95/EC (Low Voltage)

- 2012/19/EU

Care and maintenance

Cleaning the pump

The washing machine is fitted with a self-

cleaning pump which does not require any

maintenance. Sometimes, small items (such

as coins or buttons) may fall into the protective

pre-chamber at the base of the pump.

! Make sure the wash cycle has finished and

unplug the appliance.

To access the pre-chamber:

1. Take off the cover

panel on the front

of the machine by

first pressing it in

the centre and then

pushing downwards

on both sides until

you can remove it

(see figures).

2. Unscrew the lid

by rotating it anti-

clockwise (see figure):

a little water may

trickle out. This is

perfectly normal.

3. Clean the inside thoroughly.

4. Screw the lid back on.

5. Reposition the panel, making sure the hooks

are securely in place before you push it onto

the appliance.

Checking the water inlet hose

Check the inlet hose at least once a year. If

there are any cracks, it should be replaced

immediately: during the wash cycles, water

pressure is very strong and a cracked hose

could easily split open.

! Never use second-hand hoses.

Cutting off the water and electricity

supplies

• Turn off the water tap after every wash cycle.

This will limit wear on the hydraulic system inside

the washing machine and help to prevent leaks.

• Unplug the washing machine when cleaning it

and during all maintenance work.

Cleaning the washing machine

• The outer parts and rubber components

of the appliance can be cleaned using a soft

cloth soaked in lukewarm soapy water. Do not

use solvents or abrasives.

• The washing machine has a “Auto Clean”

programme for its internal parts that must be

run with no load in the drum.

For maximum performance you may want

to use either the detergent (i.e. a quantity

10% the quantity specified for lightly-soiled

garments) or special additives to clean the

washing machine. We recommend running a

cleaning programme every 40 wash cycles.

To start the programme press buttons A and

B simultaneously for 5 seconds (see figure).

The programme will start automatically and

will last approximately 70 minutes. To stop the

cycle press the START/PAUSE button.

Cleaning the detergent dispenser

drawer

To remove the drawer,

press lever (1) and pull

the drawer outwards

(2) (see figure).

Wash it under running

water; this procedure

should be repeated

frequently.

Caring for the door and drum of your

appliance

• Always leave the porthole door ajar in order to

prevent unpleasant odours from forming.

Precautions and tips

! This washing machine was designed and constructed

in accordance with international safety regulations. The

following information is provided for safety reasons and

must therefore be read carefully.

General safety

• This appliance was designed for domestic use only.

• This appliance can be used by children

aged from 8 years and above and

persons with reduced physical, sensory or

mental capabilities or lack of experience

and knowledge if they have been given

supervision or instruction concerning use of

the appliance in a safe way and understand

the hazards involved. Children shall not

play with the appliance. Cleaning and user

maintenance shall not be made by children

without supervision.

• The washing machine must only be used by adults, in

accordance with the instructions provided in this manual.

• Do not touch the machine when barefoot or with wet or

damp hands or feet.

• Do not pull on the power supply cable when unplugging

the appliance from the electricity socket. Hold the plug

and pull.

• Do not open the detergent dispenser drawer while the

machine is in operation.

• Do not touch the drained water as it may reach

extremely high temperatures.

• Never force the porthole door. This could damage the

safety lock mechanism designed to prevent accidental

opening.

• If the appliance breaks down, do not under any

circumstances access the internal mechanisms in an

attempt to repair it yourself.

• Always keep children well away from the appliance while

it is operating.

• The door can become quite hot during the wash cycle.

• If the appliance has to be moved, work in a group of two

or three people and handle it with the utmost care. Never

try to do this alone, because the appliance is very heavy.

• Before loading laundry into the washing machine, make

sure the drum is empty.

Disposal

• Disposing of the packaging materials: observe local

regulations so that the packaging may be re-used.

• The European Directive 2012/19/EU on Waste

Electrical and Electronic Equipment, requires that

old household electrical appliances must not be

disposed of in the normal unsorted municipal waste

stream. Old appliances must be collected

separately in order to optimise the recovery and

recycling of the materials they contain and reduce

the impact on human health and the environment.

The crossed out “wheeled bin” symbol on the

product reminds you of your obligation, that when

you dispose of the appliance it must be separately

collected.

Consumers should contact their local authority or

retailer for information concerning the correct

disposal of their old appliance.

Opening the porthole door manually

In the event that it is not possible to open the porthole

door due to a powercut, and if you wish to remove the

laundry, proceed as follows:

1. remove the plug from the

electrical socket.

2. make sure the water level

inside the machine is lower

than the door opening; if

it is not, remove excess

water using the drain hose,

collecting it in a bucket as

indicated in the figure.

3. remove the cover panel

on the lower front part of

the washing machine (see

figure).

4. pull outwards using the tab as indicated in the figure,

until the plastic tie-rod is freed from its stop position; pull

downwards and open the door at the same time.

5. reposition the panel, making sure the hooks are securely

in place before you push it onto the appliance.

Description of the washing

machine

Control panel

TEMPERATURE

button

WASH

CYCLE

SELECTOR

KNOB

Detergent dispenser drawer

ON/OFF

button

SPIN

button

START/PAUSE

button

and indicator light

DELAYED

START

button

OPTION

buttons

Detergent dispenser drawer: used to dispense

detergents and washing additives (see “Detergents and

laundry”).

ON/OFF button: press this briefly to switch the

machine on or off. The START/PAUSE indicator light which

flashes slowly in a green colour shows that the machine is

switched on. To switch off the washing machine during the

wash cycle, press and hold the button for approximately 3

seconds; if the button is pressed briefly or accidentally the

machine will not switch off.

If the machine is switched off during a wash cycle, this

wash cycle will be cancelled.

PUSH & WASH button: (see “Wash cycles and options”).

WASH CYCLE SELECTOR KNOB: used to set the

desired wash cycle (see “Table of wash cycles”).

OPTION buttons: press to select the available options.

The indicator light corresponding to the selected option will

remain lit.

TEMPERATURE button: press to reduce or

completely exclude the temperature; the value appears on

the display.

SPIN button: press to reduce or completely exclude

the spin cycle; the value appears on the display.

DELAYED START button: press to set a delayed

start for the selected wash cycle; the delay period appears

on the display.

START/PAUSE button and indicator light: when the

green indicator light flashes slowly, press the button to

start a wash cycle. Once the cycle has begun the indicator

light will remain lit in a fixed manner. To pause the wash

cycle, press the button again; the indicator light will flash

in an amber colour. If the symbol is not illuminated, the

door may be opened. To start the wash cycle from the

point at which it was interrupted, press the button again.

Standby mode

This washing machine, in compliance with new energy

saving regulations, is fitted with an automatic standby

system which is enabled after about 30 minutes if no

activity is detected. Press the ON-OFF button briefly and

wait for the machine to start up again.

Consumption in off-mode: 0,5 W

Consumption in Left-on: 8 W

DISPLAY

PUSH & WASH

button

The display is useful when programming the machine and provides a great deal of information.

The duration of the available wash cycles and the remaining time of a running cycle appear in section A; if the DELAYED

START option has been set, the countdown to the start of the selected wash cycle will appear.

Pressing the corresponding button allows you to view the maximum spin speed and temperature values attained by the

machine during the set wash cycle, or the values selected most recently, if these are compatible with the set wash cycle.

The hour-glass flashes while the machine processes the data on the basis of the selected programme. After a maximum of

10 minutes, the icon remains lit in a fixed manner and the final amount of time remaining is displayed. The hour-glass icon

will then switch off approximately 1 minute after the final amount of time remaining has appeared.

The “wash cycle phases” corresponding to the selected wash cycle and the “wash cycle phase” of the running wash cycle

appear in section B:

Main wash

Rinse

Spin

Drain

The “delay” symbol , when lit, indicates that the set “delayed start” value has appeared on the display.

There are three levels in section C concerning the washing options.

DOOR LOCKED indicator light:

The lit symbol indicates that the door is locked. To prevent any damage, wait until the symbol turns off before opening the

door.

To open the door while a cycle is in progress, press the START/PAUSE button; if the DOOR LOCKED symbol is switched

off the door may be opened.

Display

Running a wash cycle

Rapid programming

1. LOAD THE LAUNDRY. Open the porthole door.

Load the laundry, making sure you do not exceed

the maximum load value indicated in the table of

programmes and wash cycles on the following page.

2. ADD THE DETERGENT. Pull out the detergent

dispenser drawer and pour the detergent into the

relevant compartments as described in “Detergents and

laundry”.

3. CLOSE THE DOOR.

4. Press the “PUSH & WASH” button to start the wash

programme.

Traditional programming

1. SWITCH THE MACHINE ON. Press the button;

the START/PAUSE indicator light will flash slowly in a

green colour.

2. LOAD THE LAUNDRY. Open the porthole door.

Load the laundry, making sure you do not exceed

the maximum load value indicated in the table of

programmes and wash cycles on the following page.

3. ADD THE DETERGENT. Pull out the detergent

dispenser drawer and pour the detergent into the relevant

compartments as described in “Detergents and laundry”.

4. CLOSE THE DOOR.

5. SELECT THE WASH CYCLE. Use the WASH CYCLE

SELECTOR knob to select the desired wash cycle. A

temperature and spin speed is set for each wash cycle;

these values may be adjusted. The duration of the cycle

will appear on the display.

6. CUSTOMISE THE WASH CYCLE. Use the relevant

buttons:

Modify the temperature and/or spin

speed. The machine automatically displays the

maximum temperature and spin speed values set for

the selected cycle, or the most recently-used settings

if they are compatible with the selected cycle. The

temperature can be decreased by pressing the

button, until the cold wash “OFF” setting is reached.

The spin speed may be progressively reduced by

pressing the button, until it is completely excluded

(the “OFF” setting). If these buttons are pressed again,

the maximum values are restored.

! Exception: if the 8 programme is selected, the

temperature can be increased up to a value of 90°C.

Setting a delayed start.

To set a delayed start for the selected cycle, press the

corresponding button repeatedly until the required delay

period has been reached. When this option has been

activated, the symbol lights up on the display. To

remove the delayed start setting, press the button until

the text “OFF” appears on the display.

Modify the cycle settings.

• Press the button to enable the option; the indicator

light corresponding to the button will switch on.

• Press the button again to disable the option; the

indicator light will switch off.

! If the selected option is not compatible with the set

wash cycle, the indicator light will flash and the option

will not be activated.

! If the selected option is not compatible with another

previously selected option, the indicator light will

flash accompanied by a buzzer (3 beeps), and only

the latter option will be activated; the indicator light

corresponding to the activated option will turn on.

! The options may affect the recommended load value

and/or the duration of the cycle.

7. START THE WASH CYCLE. Press the START/

PAUSE button. The corresponding indicator light will

turn green, remaining lit in a fixed manner, and the door

will be locked (the DOOR LOCKED symbol will be lit).

To change a wash cycle while it is in progress, pause

the washing machine using the START/PAUSE button

(the START/PAUSE indicator light will flash slowly in an

amber colour); then select the desired cycle and press

the START/PAUSE button again.

To open the door while a cycle is in progress, press

the START/PAUSE button; if the DOOR LOCKED

symbol is switched off the door may be opened. Press

the START/PAUSE button again to restart the wash

cycle from the point at which it was interrupted.

8. THE END OF THE WASH CYCLE. This will be

indicated by the text “END” on the display; when the

DOOR LOCKED symbol switches off the door may

be opened. Open the door, unload the laundry and

switch off the machine.

! If you wish to cancel a cycle which has already begun,

press and hold the button. The cycle will be stopped

and the machine will switch off.

Wash cycles and options

Table of wash cycles

Wash options

Rapid

When this button is pressed the first time, the 9’ icon will

light up, when pressed the second time the 30’ icon lights

up and the third time the 1h icon lights up. When pressed

the fourth time the 9’ icon lights up again.

! It cannot be used in conjunction with wash cycles 1-2-3-

4-5-6-7-8-9-10-11-12-13- - .

Fast Forward

During a wash programme and under certain conditions,

pressing this button allows for ending the wash

programme after only 20’ if necessary, by performing a

brief rinse cycle followed by a spin cycle at maximum 800

rpm or lower, if reduced manually during the programme

customisation phase. In this case, washing and rinsing

performance will be reduced. After pressing the button, the

relative indicator light turns on together with the indicator

light of the rinse phase. If the selected temperature is

equal to 40° and/or the button is pressed during the initial

phase of the programme, the “Fast Forward” option lasts

longer so that the detergent can dissolve properly and

avoid damaging the fabrics. In this case, the rinse phase

indicator light flashes while the wash indicator light remains

fixed until the necessary activation conditions are fulfilled.

If less than 20’ remain of the wash programme, the option

will be disabled.

! It cannot be used in conjunction with wash cycles 2-4-5-

6-14- - .

Stain removal

This option allows for selecting the type of dirt so as to

optimally adjust the cycle for removing the stains. The

following types of dirt can be selected:

- Food, for stains caused by foodstuffs and beverages,

for example.

- Work, for grease and ink stains, for example.

- Outdoor, for mud and grass stains, for example.

! The wash cycle duration varies according to the type of

selected dirt.

! It cannot be used in conjunction with wash cycles 1-2-3-

4-5-6-7-11-12-13-14- - .

The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary accor-

ding to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.

1) Test wash cycle in compliance with directive 1061/2010: set wash cycle 8 with a temperature of 60°C.

This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should

be used for garments which can be washed at 60°C. The actual washing temperature may differ from the indicated value.

2) Test wash cycle in compliance with directive 1061/2010: set wash cycle 9 with a temperature of 40°C.

This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should

be used for garments which can be washed at 40°C. The actual washing temperature may differ from the indicated value.

For all Test Institutes:

2) Long wash cycle for cottons: set wash cycle 9 with a temperature of 40°C.

3) Synthetic program along: set wash cycle 10 with a temperature of 40°C.

Wash cycles

Description of the wash cycle

Max.

temp.

(°C)

Max.

speed

(rpm)

Detergents

Max. load (kg)

Residual

dampness %

Energy

consumption

kWh

Total water lt

Cycle duration

Prewash

Wash

Fabric

softener

Bleach

Special

Sport

30° 600 -

 

- 4 - - - 60’

Dark

30° 800 -

 

- 5 - - - 80’

Anti-odour (Cotton) 60° 1000 -

 

- 3,5 - - - 120’

Anti-odour (Synthetic) 40° 1000 -

 

- 3,5 - - - 105’

Delicate

30° 0 -

 

- 1 - - - 80’

Wool: for wool, cashmere, etc. 40° 800 -

 

- 2 - - - 85’

Duvet: for down-stuffed garments. 30° 1000 -

 

- 3,5 - - - 100’

Standard

Cottons with Pre-wash: extremely soiled whites. 90° 1200

  

- 8 53 2,80 105 210’

Cotton Standard 60° (1): heavily soiled whites and resistant colours.

60°

(Max. 90°)

1200 -

 

- 8 53 1,04 55 215’

Cotton Standard 40° (2): lightly soiled whites and delicate colours.

40° 1200 -

 

- 8 53 0,87 81 185’

Synthetic: heavily soiled resistant colours. 60° 800 -

 

- 4,5 46 0,86 47 115’

Synthetic (3): lightly soiled resistant colours. 40° 800 -

 

- 4,5 46 0,60 51 105’

Coloured

40° 1200 -

 

- 8 53 0,89 80 105’

Eco & Rapid

Cotton Standard 20°: lightly soiled whites and delicate colours. 20° 1200 -

 

- 8 - - - 185’

Eco Synthetic

20° 800 -

 

- 8 - - - 120’

Rapid

- 800 - -



- 1,5 - - - 9’

Rapid

30° 800 -

 

- 3,5 80 0,18 43 30’

Rapid

60° 1000 -

 

- 8 - - - 60’

Partials

Rinse/Bleach - 1200 - -

 

8 - - - 55’

Spin + Drain - 1200 - - - - 8 - - - 25’

Push & Wash

This function allows for starting a wash cycle even when the machine is switched off without having to press the ON/OFF

button in advance, or after switching on the machine, without having activated any button and/or selector (otherwise, the

Push & Wash function will be deactivated). To start the Push & Wash cycle press and hold the relative button for 2 seconds.

The lit indicator light indicates that the cycle has started. This wash cycle is ideal for cotton or synthetic fabrics, as it washes

at a temperature of 30° and a maximum spin speed of 1200 rpm. Maximum load 4 kg. (Cycle duration 50’).

How does it work?

1. Load the laundry (cotton and/or synthetic garments) and close the door.

2. Pour the detergent and additives.

3. Start the programme by pressing and holding the Push & Wash button for 2 seconds. The relative indicator light turns

green and the door will lock (the DOOR LOCKED symbol turns on).

N.B.: starting the wash cycle through the Push & Wash button activates an automatic non-customisable cycle

recommended for cotton and synthetic fabrics. This programme does not allow for setting any additional options.

To open the door while an automatic cycle is under way, press the START/PAUSE button; if the DOOR LOCKED symbol

is switched off the door may be opened. Press the START/PAUSE button again to restart the wash cycle from the point at

which it was interrupted.

4. Once the programme is finished, the END indicator light turns on.

Detergents and laundry

Detergent dispenser drawer

Successful washing results also depend on the correct

dose of detergent: adding too much detergent will not

necessarily result in a more efficient wash, and may in

fact cause build up on the inside of your appliance and

contribute to environmental pollution.

! Do not use hand washing detergents because these

create too much foam.

! Use powder detergent for white cotton garments, for pre-

washing, and for washing at temperatures over 60°C.

! Follow the instructions given on the detergent packaging.

Open the detergent

dispenser drawer and pour

in the detergent or washing

additive, as follows.

Compartment 1: Pre-wash detergent (powder)

Before pouring in the detergent, make sure that extra

compartment 4 has been removed.

Compartment 2: Washing detergent (powder or liquid)

If liquid detergent is used, it is recommended that the

removable plastic partition A (supplied) be used for proper

dosage. If powder detergent is used, place the partition

into slot B.

Compartment 3: Additives (fabric softeners, etc.)

The fabric softener must not exceed the “max” level indicated

on the central pin.

Extra compartment 4: Bleach

Bleach cycle

Insert the additional compartment 4 (provided) into

compartment 1. In pouring the bleach do not exceed the

“max” level indicated on the central pin.

Perform bleaching by pouring the bleach into additional

compartment 4 and set the programme .

! Traditional bleach should be used on resistant white

fabrics, and delicate bleach for coloured and synthetics

fabrics and for wool.

Preparing the laundry

• Divide the laundry according to:

- the type of fabric/the symbol on the label

- the colours: separate coloured garments from whites.

• Empty all garment pockets and check the buttons.

• Do not exceed the values listed in the “Table of wash

cycles”, which refer to the weight of the laundry when dry.

How much does your laundry weigh?

1 sheet 400-500 g

1 pillow case 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1.200 g

1 towel 150-250 g

Special wash cycles

Sport (programme 1) is designed for washing lightly soiled

sports clothing (tracksuits, shorts, etc.); for best results, we

recommend not exceeding the maximum load indicated

in the “Table of wash cycles”. We recommend using liquid

detergent, and adding the amount suitable for a half-load.

Dark: use programme 2 to wash dark-coloured garments.

This programme is designed to maintain dark colours over

time. We recommend using a liquid detergent for the best

results when washing dark-coloured garments.

Anti-odour: use programme 3 for washing garments

with bad odours (e.g. smoke, sweat, fried food). The

programme is designed to remove bad odours while

preserving the fabric fibres. Synthetics fabrics or mixed

loads should be washed at 40°, and resistant cotton

fabrics at 60°.

Delicate: use programme 4 to wash very delicate

garments. It is advisable to turn the garments inside out

before washing them. For best results, use liquid detergent

on delicate garments.

Wool: the wool wash programme of this machine has

been tested and approved by The Woolmark Company

for the washing of wool containing garments labelled as

“hand wash” provided that the garments are washed

according to the instructions on the garment label and

those issued by the manufacturer of this washing machine.

(M1127)

In UK, Eire, Hong Kong and India the Woolmark trade mark

is a Certification trade mark.

Duvet: to wash double or single duvets (the weight of

which should not exceed 3,5 kg), cushions or clothes

padded with goose down such as puffa jackets, use the

special wash programme number 6. We recommend that

duvets are placed in the drum with their edges folded

inwards (see figure) and that no more than ¾ of the total

volume of the drum is used. To achieve the best results,

we recommend that a liquid detergent is used and placed

inside the detergent dispenser drawer.

Coloured: use this programme 11 to wash bright

coloured clothes. The programme is designed to maintain

bright colours over time.

Cotton Standard 20° (programme 12) ideal for lightly

soiled cotton loads. The effective performance levels

achieved at cold temperatures, which are comparable to

washing at 40°, are guaranteed by a mechanical action

which operates at varying speed, with repeated and

frequent peaks.

Eco Synthetic (programme 13) ideal for mixed loads

(cotton and synthetics) with a normal soil level. The

effective performance levels achieved at cold temperatures

are guaranteed by a mechanical action which operates at

varying speed, across set average intervals.

Rapid (programme 14) allows for varying the garment

treatment duration from 9’ to 1h. Pressing the

corresponding “Rapid” button allows for varying the cycle

duration between 9’ (refresh), 30’ (wash), 1h (wash).

The 9’ cycle refreshes garments using fabric softener

only; it is advisable not to add any detergent into

the machine. The 30’ programme is designed to wash

lightly soiled garments at 30° (excluding wool and silk)

with a 3 kg maximum load in a short time: it only lasts 30

minutes and allows for saving time and energy. The “1h”

cycle is designed to wash moderately soiled resistant

cotton garments at 60° in an hour, with good washing

performance. For synthetic or mixed garments, we

recommend lowering the temperature down to 40°.

Load balancing system

Before every spin cycle, to avoid excessive vibrations

before every spin and to distribute the load in a uniform

manner, the drum rotates continuously at a speed which

is slightly greater than the washing rotation speed. If,

after several attempts, the load is not balanced correctly,

the machine spins at a reduced spin speed. If the load is

excessively unbalanced, the washing machine performs

the distribution process instead of spinning. To encourage

improved load distribution and balance, we recommend

small and large garments are mixed in the load.

Troubleshooting

Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Service (see “ Service”),

make sure that the problem cannot be solved easily using the following list.

Problem:

The washing machine does not

switch on.

The wash cycle does not start.

The washing machine does not fill

with water (the text “H2O” on the

display).

The washing machine

continuously takes in and drains

water.

The washing machine does not

drain or spin.

The washing machine vibrates a

lot during the spin cycle.

The washing machine leaks.

The “option” and START/PAUSE

indicator lights flash rapidly and an

error code appears on the display

(e.g.: F-01, F-..).

There is too much foam.

Push & Wash does not activate.

The programme lasts a lot less

that expected.

Possible causes / Solutions:

• The appliance is not plugged into the socket fully, or not enough to make contact.

• There is no power in the house.

• The washing machine door is not closed properly.

• The ON/OFF button has not been pressed.

• The START/PAUSE button has not been pressed.

• The water tap has not been opened.

• A delayed start has been set.

• The water inlet hose is not connected to the tap.

• The hose is bent.

• The water tap has not been opened.

• There is no water supply in the house.

• The pressure is too low.

• The START/PAUSE button has not been pressed.

• The drain hose is not fitted at a height between 65 and 100 cm from the floor

(see “Installation”).

• The free end of the hose is under water (see “Installation”).

• The wall drainage system is not fitted with a breather pipe.

If the problem persists even after these checks, turn off the water tap, switch the

appliance off and contact the Technical Assistance Service. If the dwelling is on one

of the upper floors of a building, there may be problems relating to water drainage,

causing the washing machine to fill with water and drain continuously. Special anti-

draining valves are available in shops and help to prevent this inconvenience.

• The wash cycle does not include draining: some cycles require the draining

process to be enabled manually.

• The drain hose is bent (see “Installation”).

• The drainage duct is clogged.

• The drum was not unlocked correctly during installation (see “Installation”).

• The washing machine is not level (see “Installation”).

• The washing machine is trapped between cabinets and walls (see “Installation”).

• The water inlet hose is not screwed on properly (see “Installation”).

• The detergent dispenser drawer is blocked (for cleaning instructions, see “Care

and maintenance”).

• The drain hose is not fixed properly (see “Installation”).

• Switch off the machine and unplug it, wait for approximately 1 minute and then

switch it back on again.

If the problem persists, contact the Technical Assistance Service.

• The detergent is not suitable for machine washing (it should display the text “for

washing machines” or “hand and machine wash”, or the like).

• Too much detergent was used.

• After switching on the machine a control other than Push & Wash was activated.

Switch the machine off and press the Push & Wash button.

• The “Fast Forward” option was activated.

Service

Before contacting the Technical Assistance Service:

• Check whether you can solve the problem alone (see “Troubleshooting”).

• Restart the wash cycle to check whether the problem has been solved.

• If this is not the case, contact an authorised Technical Assistance Centre.

! Always request the assistance of authorised technicians.

Have the following information to hand:

• the type of problem;

• the appliance model (Mod.);

• the serial number (S/N).

This information can be found on the data plate applied to the rear of the washing machine, and can also be found on the

front of the appliance by opening the door.

LAVADORA

Sumario

Instalación, 16-17

Desembalaje y nivelación

Conexiones hidráulicas y eléctricas

Primer ciclo de lavado

Datos técnicos

Mantenimiento y cuidados, 18

Interrumpir el agua y la corriente eléctrica

Limpiar la lavadora

Limpiar el contenedor de detergentes

Cuidar la puerta y el cesto

Limpiar la bomba

Controlar el tubo de alimentación de agua

Precauciones y consejos, 19

Seguridad general

Eliminación

Apertura manual de la puerta

Descripción de la lavadora, 20-21

Panel de control

Pantalla

Cómo efectuar un ciclo de lavado, 22

Programas y opciones, 23-24

Tabla de programas

Opciones de lavado

Push & Wash

Detergentes y ropa, 25-26

Contenedor de detergentes

Ciclo de blanqueo

Preparar la ropa

Programas particulares

Sistema de equilibrado de la carga

Anomalías y soluciones, 27

Asistencia Técnica, 28

Manual de instrucciones

Español

XWE 81283

Instalación

! Es importante conservar este manual para

poder consultarlo en cualquier momento.

En caso de venta, de cesión o de traslado,

verifique que permanezca junto con la

lavadora para informar al nuevo propietario

sobre el funcionamiento y brindar las

correspondientes advertencias.

! Lea atentamente las instrucciones: ellas

contienen importante información sobre la

instalación, el uso y la seguridad.

Desembalaje y nivelación

Desembalaje

1. Desembale la lavadora.

2. Controle que la lavadora no haya sufrido

daños durante el transporte. Si estuviera

dañada no la conecte y llame al revendedor.

3. Quite los 4 tornillos

de protección

para el transporte

y la arandela

de goma con el

correspondiente

distanciador ubicados

en la parte posterior

(ver la figura).

4. Cubra los orificios con los tapones de

plástico suministrados con el aparato.

5. Conserve todas las piezas: cuando la

lavadora deba ser transportada nuevamente,

deberán volver a colocarse.

! Los embalajes no son juguetes para los

niños.

Nivelación

1. Instale la lavadora sobre un piso plano y

rígido, sin apoyarla en las paredes, muebles ni

en ningún otro aparato.

2. Si el piso no

está perfectamente

horizontal, compense

las irregularidades

desenroscando o

enroscando las patas

delanteras (ver la

figura); el ángulo de

inclinación medido

sobre la superficie

de trabajo, no debe

superar los 2º.

Una cuidadosa nivelación brinda estabilidad

a la máquina y evita vibraciones, ruidos y

desplazamientos durante el funcionamiento.

Cuando se instala sobre moquetas o

alfombras, regule los pies para conservar

debajo de la lavadora un espacio suficiente

para la ventilación.

Conexiones hidráulicas y

eléctricas

Conexión del tubo de alimentación de

agua

1. Conectar el tubo

de tubo enroscándolo

a un grifo de agua fría

con la boca roscada

de 3/4 gas (ver la

figura).

Antes de conectarlo,

haga correr el agua

hasta que esté

límpida.

2. Conecte el tubo

de alimentación

a la lavadora

enroscándolo en

la toma de agua

correspondiente

ubicada en la parte

posterior derecha

(arriba) (ver la figura).

3. Controle que en el tubo no hayan pliegues

ni estrangulaciones.

! La presión de agua del grifo debe estar

comprendida dentro de los valores contenidos

en la tabla de Datos técnicos (ver la página

correspondiente).

! Si la longitud del tubo de alimentación

no es la suficiente, diríjase a un negocio

especializado o a un técnico autorizado.

! No utilice nunca tubos ya usados.

! Utilice los suministrados con la máquina.

Conexión del tubo de desagüe

Conecte el tubo de

desagüe, sin plegarlo,

a un conducto de

desagüe o a una

desagüe de pared

ubicados a una

distancia del piso

comprendida entre

65 y 100 cm.;

o apóyelo en

el borde de un

lavamanos o de una

bañera, uniendo la

guía suministrada

con el aparato, al

grifo (ver la figura).

El extremo libre del

tubo de desagüe no

debe permanecer

sumergido en el

agua.

! No se aconseja utilizar tubos de

prolongación, si fuera indispensable hacerlo,

la prolongación debe tener el mismo diámetro

del tubo original y no superar los 150 cm.

Conexión eléctrica

Antes de enchufar el aparato, verifique que:

• la toma tenga la conexión a tierra y haya

sido hecha según las normas legales;

• la toma sea capaz de soportar la carga

máxima de potencia de la máquina indicada

en la tabla de Datos técnicos (ver al costado);

• la tensión de alimentación esté comprendida

dentro de los valores indicados en la tabla

de Datos técnicos (ver al costado);

• la toma sea compatible con el enchufe de la

lavadora. Si no es así, sustituya la toma o el

enchufe.

! La lavadora no debe ser instalada al aire

libre, ni siquiera si el lugar está reparado, ya

que es muy peligroso dejarla expuesta a la

lluvia o a las tormentas.

! Una vez instalada la lavadora, la toma de

corriente debe ser fácilmente accesible.

! No utilice prolongaciones ni conexiones

múltiples.

65 - 100 cm

! El cable no debe estar plegado ni sufrir

compresiones.

! El cable de alimentación debe ser sustituido

sólo por técnicos autorizados.

¡Atención! La empresa fabricante declina toda

responsabilidad en caso de que estas normas

no sean respetadas.

Primer ciclo de lavado

Después de la instalación y antes del uso,

realice un ciclo de lavado con detergente y

sin ropa, seleccionando el programa “Auto

Limpieza” (ver “Limpiar la lavadora”).

Datos técnicos

Modelo

XWE 81283

Dimensio-

nes

ancho 59.5 cm

altura 85 cm

profundidad 60,5 cm

Capacidad

de 1 a 8 kg

Conexiones

eléctricas

ver la placa de característi-

cas técnicas aplicada en la

máquina

Conexiones

hídricas

presión máxima

1 MPa (10 bar)

presión mínima

0,05 MPa (0,5 bar)

capacidad del cesto 62 litros

Velocidad

de centrifu-

gado

máxima 1200 r.p.m.

Programas

de control

según las

directivas

1061/2010 y

1015/2010

programa 8;

Algodón Standard 60ºC.

programa 9;

Algodón Standard 40ºC.

Esta máquina cumple con lo

establecido por las siguientes

Directivas de la Comunidad:

- 2004/108/CE (Compatibili-

dad Electromagnética)

- 2012/19/EU

- 2006/95/CE (Baja Tensión)

Limpiar la bomba

La lavadora posee una bomba autolimpiante

que no necesita mantenimiento. Pero puede

suceder que objetos pequeños (monedas,

botones) caigan en la precámara que protege

la bomba, situada en la parte inferior de la

misma.

! Verifique que el ciclo de lavado haya

terminado y desenchufe la máquina.

Para acceder a la precámara:

1. quite el panel de

cobertura delantero

de la máquina

presionando hacia el

centro, luego empuje

hacia abajo desde

ambos costados y

extráigalo (ver las

figuras).

2. desenrosque la

tapa girándola en

sentido antihorario

(ver la figura): es

normal que se

vuelque un poco de

agua;

3. limpie con cuidado el interior;

4. vuelva a enroscar la tapa;

5. vuelva a montar el panel verificando,

antes de empujarlo hacia la máquina, que

los ganchos se hayan introducido en las

correspondientes ranuras.

Controlar el tubo de alimentación

de agua

Controle el tubo de alimentación al menos

una vez al año. Si presenta grietas o rajaduras

debe ser sustituido: durante los lavados, las

fuertes presiones podrían provocar roturas

imprevistas.

! No utilice nunca tubos ya usados.

Mantenimiento y cuidados

Interrumpir el agua y la corriente

eléctrica

• Cierre el grifo de agua después de cada lavado.

De este modo se limita el desgaste de la

instalación hidráulica de la lavadora y se

elimina el peligro de pérdidas.

• Desenchufe la máquina cuando la

debe limpiar y durante los trabajos de

mantenimiento.

Limpiar la lavadora

• La parte externa y las partes de goma

se pueden limpiar con un paño embebido

en agua tibia y jabón. No use solventes ni

productos abrasivos.

• La lavadora posee un programa de “Auto

Limpieza” de su interior que se debe realizar

sin ningún tipo de carga en el cesto.

El detergente (en un 10% de la cantidad

aconsejada para prendas poco sucias)

o algunos aditivos específicos para la

limpieza de la ropa se podrán utilizar como

coadyuvantes en el programa de lavado. Se

aconseja efectuar el programa de limpieza

cada 40 ciclos de lavado.

Para activar el programa pulse simultáneamente

los botones A y B durante 5 segundos

(ver la figura). El programa comenzará

automáticamente y tendrá una duración de 70

minutos aproximadamente. Para detener el ciclo

presione el botón START/PAUSE.

Limpiar el cajón de detergentes

Para extraer el cajón,

presione la palanca (1)

y tire hacia afuera (2)

(ver la figura).

Lávelo debajo del agua

corriente, esta limpieza

se debe realizar

frecuentemente.

Cuidar la puerta y el cesto

• Deje siempre semicerrada la puerta para

evitar que se formen malos olores.

Precauciones y consejos

! La lavadora fue proyectada y fabricada en conformidad

con las normas internacionales de seguridad. Estas

advertencias se suministran por razones de seguridad y

deben ser leídas atentamente.

Seguridad general

• Este aparato ha sido fabricado para un uso de tipo

doméstico exclusivamente.

• Este aparato puede ser utilizado por

niños de 8 años o más y por personas

con capacidades físicas, sensoriales o

mentales disminuidas o con experiencia y

conocimientos insuficientes siempre que

sean supervisados o que hayan recibido

una adecuada formación sobre el uso

del aparato en forma segura y conozcan

los peligros derivados del mismo. Los

niños no deben jugar con el aparato. El

mantenimiento y la limpieza no deben ser

realizados por niños sin supervisión.

• La lavadora debe ser utilizada sólo por personas

adultas y siguiendo las instrucciones contenidas en este

manual.

• No toque la máquina con los pies desnudos ni con las

manos o los pies mojados o húmedos.

• No desenchufe la máquina tirando el cable, sino

tomando el enchufe.

• No abra el cajón de detergentes mientras la máquina

está en funcionamiento.

• No toque el agua de descarga ya que puede alcanzar

temperaturas elevadas.

• En ningún caso fuerce la puerta: podría dañarse el

mecanismo de seguridad que la protege de aperturas

accidentales.

• En caso de avería, no acceda nunca a los mecanismos

internos para intentar una reparación.

• Controle siempre que los niños no se acerquen a la

máquina cuando está en funcionamiento.

• Durante el lavado, la puerta tiende a calentarse.

• Si debe ser trasladada, deberán intervenir dos o más

personas, procediendo con el máximo cuidado. La

máquina no debe ser desplazada nunca por una sola

persona ya que es muy pesada.

• Antes de introducir la ropa controle que el cesto esté

vacío.

Eliminaciones

• Eliminación del material de embalaje:

respete las normas locales, de ese modo, los embalajes

podrán volver a ser utilizados.

• La norma Europea 2012/19/EU sobre la eliminación

de aparatos eléctricos y electrónicos, indica que los

electrodomésticos no deben ser eliminados de la

misma manera que los desechos sólidos urbanos. Los

aparatos en desuso se deben recoger separadamente

para optimizar el porcentaje de recuperación y

reciclaje de los materiales que los componen e impedir

potenciales daños para la salud y el medio ambiente. El

símbolo de la papelera tachada se encuentra en todos

los productos para recordar la obligación de recolección

separada.

Para mayor información sobre la correcta eliminación de

los electrodomésticos, los poseedores de los mismos

podrán dirigirse al servicio público responsable o a los

revendedores.

Apertura manual de la puerta

Si falta la energía eléctrica es posible abrir la puerta para

descargar la ropa del siguiente modo:

1. desenchufe la máquina.

2. verifique que el nivel

de agua en el interior de

la máquina sea inferior al

hueco de la puerta; si no

es así, extraiga el agua en

exceso utilizando el tubo de

descarga y recogiéndola en

un balde como se indica en

la figura.

3. quite el panel de cobertura

delantero de la lavadora (ver

la página siguiente).

4. utilizando la lengüeta indicada en la figura, tire hacia

fuera hasta liberar la varilla de plástico del retén; tire

posteriormente hacia abajo hasta sentir un breve sonido

que indica que la puerta está desbloqueada.

5. vuelva a montar el panel verificando, antes de empujarlo

hacia la máquina, que los ganchos se hayan introducido

en las correspondientes ranuras.

Descripción de la lavadora

Panel de control

Botón

TEMPERATURA

MANDO DE

PROGRAMAS

Cajón de detergentes

Botón ON/OFF

Botón de

CENTRIFUGADO

Botón y piloto

START/PAUSE

PANTALLA

Botón

COMIENZO

RETRASADO

Botones

OPCIÓN

Cajón de detergentes: para cargar detergentes y

aditivos (ver “Detergentes y ropa”).

Botón ON/OFF : presione brevemente el botón

para encender o apagar la máquina. El piloto START/

PAUSE que centellea lentamente en color verde indica

que la máquina está encendida. Para apagar la lavadora

durante el lavado, es necesario mantener presionado el

botón durante más tiempo, aproximadamente 3 seg.; si

se presiona en forma más breve o accidental, la máquina

no se apagará. Si la máquina se apaga durante un lavado

en curso, dicho lavado se anulará.

Botón PUSH & WASH: (ver “Programas y opciones”).

MANDO DE PROGRAMAS: para seleccionar el

programa deseado (ver “Tabla de programas”).

Botones OPCIÓN: para seleccionar las opciones

disponibles. El piloto correspondiente a la opción

seleccionada permanecerá encendido.

Botón CENTRIFUGADO : presiónelo para disminuir

o excluir totalmente el centrifugado; el valor se indica en

la pantalla.

Botón TEMPERATURA : presiónelo para disminuir o

excluir la temperatura; el valor se indica en la pantalla.

Botón COMIENZO RETRASADO : presiónelo

para seleccionar un comienzo retrasado del programa

previamente elegido; el retraso se indica en la pantalla.

Botón y piloto START/PAUSE : cuando el piloto verde

centellea lentamente, presione el botón para que comience

el lavado. Una vez que el ciclo ha comenzado, el piloto

se mantiene fijo. Para poner en pausa el lavado, presione

nuevamente el botón; el piloto centelleará de color ámbar.

Si el símbolo no está iluminado, se podrá abrir la puerta.

Para que el lavado se reanude a partir del momento en el

cual fue interrumpido, presione nuevamente el botón.

Modalidad de stand by

Esta lavadora está en conformidad con las nuevas

normativas vinculadas al ahorro energético. Está

dotada de un sistema de auto-apagado (stand by)

que, en caso de no funcionamiento, se activa pasados

aproximadamente 30 minutos. Presionar brevemente el

botón ON/OFF y esperar que la máquina se active.

Consumo en off-mode: 0,5 W

Consumo en Left-on: 8 W

Botón

PUSH & WASH

Stránka sa načítava ...

Indesit XWE 81283X W EU Užívateľská príručka

Značka: Indesit

Model: XWE 81283X W EU

Kategória: Práčky

Typ: Užívateľská príručka

Stiahnite si PDF

správa

V iných jazykoch

português: Indesit XWE 81283X W EU Guia de usuario
español: Indesit XWE 81283X W EU Guía del usuario

Indesit XWE 81283X W EU Užívateľská príručka

Indesit XWE 81283X W EU Užívateľská príručka

V iných jazykoch

Ďalšie dokumenty