Sony KDL-32S2800 Návod na obsluhu

LCD Digital Colour TV

3-217-695-42(1)

K

KDL-40S28xx

KDL-40T26xx

KDL-32S28xx

KDL-32T26xx

Operating Instructions

Before operating the TV, please read the “Safety information”

section of this manual. Retain this manual for future reference.

Инструкция по эксплуатации

Перед включением телевизора прочтите раздел “Сведения

по безопасности” этого руководства. Сохраняйте данное

руководство для справок в будущем.

Instrukcja obsługi

Przed rozpoczęciem eksploatacji telewizora należy zapoznać się

z treścią rozdziału „Informacje dotyczące bezpieczeństwa”

niniejszej instrukcji. Zachować instrukcję do wykorzystania w

przyszłości.

Návod k použití

Před zapnutím televizoru si prosím pozorně přečtěte část

„Bezpečnostní údaje“ v tomto návodu. Návod si uschovejte i pro

budoucí potřebu.

For useful information about Sony products

Для получения полезной информации о продукции Сони

Szczegółowe informacje o produktach Sony

Užitečné informace o výrobcích Sony

Pre viac informácií o produktoch Sony

Sony termékekről hasznos információkat találhat az alábbi

weboldalon

Návod na obsluhu

Pred zapnutím TV prijímača si prosím pozorne prečítajte čas˙

„Informácie o bezpečnosti“. Návod si uchovajte pre ďašie použitie.

Kezelési utasítás

Mielőtt elkezdené használni a televíziót, kérjük, olvassa el a jelen

kézikönyv Biztonsági előírások c. szakaszát. Őrizze meg a

kézikönyvet későbbi használatra.

GB

RU

PL

CZ

SK

HU

Printed in Spain

3-217-695-42(1)

K

KDL-40S28xx

KDL-40T26xx

KDL-32S28xx

KDL-32T26xx

LCD Digital Colour TV

2

GB

Thank you for choosing this Sony product.

Before operating the TV, please read this manual thoroughly

and retain it for future reference.

Disposal of Old Electrical &

Electronic Equipment

(Applicable in the European

Union and other European

countries with separate

collection systems)

This symbol on the product or on

its packaging indicates that this

product shall not be treated as

household waste. Instead it shall

be handed over to the applicable

collection point for the recycling

of electrical and electronic equipment. By ensuring this

product is disposed of correctly, you will help prevent

potential negative consequences for the environment and

human health, which could otherwise be caused by

inappropriate waste handling of this product. The recycling

of materials will help to conserve natural resources. For more

detailed information about recycling of this product, please

contact your local Civic Office, your household waste

disposal service or the shop where you purchased the

product.

• Any functions related to Digital TV ( ) will only

work in countries or areas where DVB-T (MPEG2) digital

terrestrial signals are broadcasted. Please confirm with

your local dealer if you can receive a DVB-T signal where

you live.

• Although this TV set follows DVB-T specifications,

compatibility with future DVB-T digital terrestrial

broadcasts cannot be guaranteed.

• Some Digital TV functions may not be available in some

countries.

Introduction

Disposal of the TV set

Notice for Digital TV function

• is a registered trademark of the DVB Project

• Manufactured under license from BBE Sound, Inc.

Licensed by BBE Sound, Inc. under one or more of the

following US patents: 5510752, 5736897. BBE and BBE

symbol are registered trademarks of BBE Sound, Inc.

• Manufactured under license from Dolby Laboratories.

“Dolby” and the double-D symbol are trademarks of

Dolby Laboratories.

• HDMI, the HDMI logo and High-Definition Multimedia

Interface are trademarks or registered trademarks of

HDMI Licensing LLC.

~

• The illustrations used in this manual are of the

KDL-32S28xx unless otherwise state.

• The "xx" that appears on the model name, corresponds to

two numeric digits related to colour variation.

Trademark information

DIGITAL

010COV.book Page 2 Monday, July 23, 2007 12:08 PM

3

GB

Table of Contents

Start-up Guide 4

Safety information.....................................................................................................................7

Precautions...............................................................................................................................8

Overview of the remote ..........................................................................................................9

Overview of the TV buttons and indicators........................................................................10

Watching TV............................................................................................................................11

Checking the Digital Electronic Programme Guide (EPG) ............................................13

Using the Digital Favourite list ......................................................................................15

Connecting optional equipment...............................................................................................16

Viewing pictures from connected equipment ..........................................................................17

Using HDMI control.................................................................................................................18

Navigating through menus......................................................................................................19

Picture Adjustment menu........................................................................................................20

Sound Adjustment menu.........................................................................................................22

Features menu........................................................................................................................24

Set-up menu............................................................................................................................26

Digital Set-up menu .....................................................................................................29

Specifications..........................................................................................................................31

Troubleshooting ......................................................................................................................33

Start-up Guide 4

Watching TV

Using Optional Equipment

Using MENU Functions

Additional Information

GB

: for digital channels only

010COV.book Page 3 Monday, July 23, 2007 12:08 PM

4

GB

Start-up Guide

1: Checking the

accessories

Mains lead (1) (only for KDL-40T26xx, KDL-40S28xx)

Coaxial cable* (1) (only for KDL-40T26xx, KDL-

40S28xx)

Remote RM-ED009 (1)

Size AA batteries (R6 type) (2)

Support belt (1) and screws (2)

To insert batteries into the remote

~

• Observe the correct polarity when inserting batteries.

• Do not use different types of batteries together or mix old

and new batteries.

• Dispose of batteries in an environmentally friendly way.

Certain regions may regulate disposal of batteries. Please

consult your local authority.

• Handle the remote with care. Do not drop or step on it, or

spill liquid of any kind onto it.

• Do not place the remote in a location near a heat source, a

place subject to direct sunlight, or a damp room.

2: Connecting an aerial/

VCR

Push and lift the cover to open.

C

onnecting an aerial only

Connecting an aerial and VCR

Coaxial cable*

Scart lead (not supplied)

VCR

Coaxial cable

(not supplied)

Coaxial cable*

010COV.book Page 4 Monday, July 23, 2007 12:08 PM

5

GB

Start-up Guide

3: Preventing the TV

from toppling over

4: Connecting the

cables

5: Bundling the cables

6:

Selecting the language

and country/region

1 Connect the TV to your mains socket

(220-240V AC, 50Hz).

2 Press 1 on the TV (top side).

When you switch on the TV for the first time, the

Language menu appears on the screen.

3 Press F/f to select the language displayed on the

menu screens, then press .

KDL-40T26xx

KDL-40S28xx

3,4

Auto Start Up

Language

Country

Select:

Confirm:

Continued

010COV.book Page 5 Monday, July 23, 2007 12:08 PM

6

GB

4 Press F/f to select the country/region in

which you will operate the TV, then press

.

If the country/region in which you want to use the

TV does not appear in the list, select “-” instead of

a country/region.

7: Auto-tuning the TV

1 Before you start auto-tuning the TV, insert

a pre-recorded tape into the VCR

connected to the TV (page 4) and start play

back.

The video channel will be located and stored on

the TV during auto-tuning.

If no VCR is connected to the TV, skip this step.

2 Press .

The TV starts searching for all available digital

channels, followed by all available analogue

channels. This may take some time, so do not

press any buttons on the TV or remote while

proceeding.

If a message appears for you to confirm the aerial

connection

No digital or analogue channels were found.

Check all the aerial connections and press to

start auto-tuning again.

3 When the Programme Sorting menu

appears on the screen, follow the steps of

“Programme Sorting”(page 26).

If you do not change the order in which the

analogue channels are stored on the TV, go to

step 4.

4 Press MENU to exit.

The TV has now tuned in all the available

channels.

~

When a digital broadcast channel cannot be received, or

when selecting a region in which there are no digital

broadcasts in step 4 (page 6), the time must be set after

performing step 4.

Detaching the Table-

Top Stand from the TV

~

Do not remove the Table-Top Stand for any reason other than

to wall-mount the TV.

Auto Start Up

Language

Country

Select:

Confirm:

Back:

Start:

Cancel:

MENU

Do you want to start automatic tuning?

KDL-40T26xx

KDL-40S28xx

KDL-32T26xx

KDL-32S28xx

010COV.book Page 6 Monday, July 23, 2007 12:08 PM

7

GB

Safety information

Installation/Set-up

Install and use the TV set in accordance with the

instructions below in order to avoid any risk of fire,

electrical shock or damage and/or injuries.

Installation

• The TV set should be installed near an easily accessible

mains socket.

• Place the TV set on a stable, level surface.

• Only qualified service personnel should carry out wall

installations.

• For safety reasons, it is strongly recommended that you

use Sony accessories, including:

– Wall-mount bracket SU-WL500

Transporting

• Before transporting the TV set,

disconnect all cables.

• Two or three people are needed to

transport a large TV set.

• When transporting the TV set by

hand, hold it as shown on the right.

• When lifting or moving the TV set,

hold it firmly from the bottom. Do

not put stress on the LCD panel.

• When transporting the TV set, do

not subject it to jolts or excessive

vibration.

• When transporting the TV set for

repairs or when moving, pack it using the original carton

and packing material.

Ventilation

• Never cover the ventilation holes or insert anything in the

cabinet.

• Leave space around the TV set as shown below.

• It is strongly recommended that you use a Sony wall-

mount bracket in order to provide adequate air-circulation.

Installed on the wall

Installed with stand

• To ensure proper ventilation and prevent the collection of

dirt or dust:

– Do not lay the TV set flat, install upside down,

backwards, or sideways.

– Do not place the TV set on a shelf, rug, bed or in a

closet.

– Do not cover the TV set with a cloth, such as curtains,

or items such as newspapers, etc.

– Do not install the TV set as shown below.

Mains lead

Handle the mains lead and socket as follows in order

to avoid any risk of fire, electrical shock or damage

and/or injuries:

Connect the TV set using a three-wire grounding type

mains plug to a mains socket with a protective earthing

connection (only for KDL-40T26xx, KDL-40S28xx).

– Use only Sony mains leads, not those of other brands.

– Insert the plug fully into the mains socket.

– Operate the TV set on a 220-240 V AC supply only.

– When wiring cables, be sure to unplug the mains lead

for your safety and care not to catch your feet on the

cables.

– Disconnect the mains lead from the mains socket before

working on or moving the TV set.

– Keep the mains lead away from heat sources.

– Unplug the mains plug and clean it regularly. If the plug

is covered with dust and it picks up moisture, its

insulation may deteriorate, which could result in a fire.

30 cm

10 cm

Leave at least this space around the set.

30 cm

10 cm10 cm

6 cm

Leave at least this space around the set.

Air circulation

is blocked.

Air circulation

is blocked.

Wall

Continued

010COV.book Page 7 Monday, July 23, 2007 12:08 PM

8

GB

Notes

• Do not use the supplied mains lead on any other

equipment.

• Do not pinch, bend, or twist the mains lead excessively.

The core conductors may be exposed or broken.

• Do not modify the mains lead.

• Do not put anything heavy on the mains lead.

• Do not pull on the mains lead itself when disconnecting

the mains lead.

• Do not connect too many appliances to the same mains

socket.

• Do not use a poor fitting mains socket.

Prohibited Usage

Do not install/use the TV set in locations,

environments or situations such as those listed below,

or the TV set may malfunction and cause a fire,

electrical shock, damage and/or injuries.

Location:

Outdoors (in direct sunlight), at the seashore, on a ship or

other vessel, inside a vehicle, in medical institutions, near

flammable objects (candles, etc).

Environment:

Places that are hot, humid, or excessively dusty; where

insects may enter; where it might be exposed to mechanical

vibration; unstable locations; near water, rain, moisture or

smoke.

Situation:

Do not use when your hands are wet, with the cabinet

removed, or with attachments not recommended by the

manufacturer. Disconnect the TV set from mains socket and

aerial during lightning storms.

Broken pieces:

• Do not throw anything at the TV set. The screen glass may

break by the impact and cause serious injury.

• If the surface of the TV set cracks, do not touch it until you

have unplugged the mains lead. Otherwise electric shock

may result.

When not in use

• If you will not be using the TV set for several days, the TV

set should be disconnected from the mains for

environmental and safety reasons.

• As the TV set is not disconnected from the mains when the

TV set is just turned off, pull the plug from the mains to

disconnect the TV set completely.

• However, some TV sets may have features that require the

TV set to be left in standby to work correctly.

For children

• Do not allow children to climb on the TV set.

• Keep small accessories out of the reach of children, so that

they are not mistakenly swallowed.

If the following problems occur...

Turn off the TV set and unplug the mains lead

immediately if any of the following problems occur.

Ask your dealer or Sony service centre to have it

checked by qualified service personnel.

When:

– Mains lead is damaged.

– Poor fitting of mains socket.

– TV set is damaged by being dropped, hit or having

something thrown at it.

– Any liquid or solid object falls through openings in the

cabinet.

Precautions

Viewing the TV

• View the TV in moderate light, as viewing the TV in poor

light or during long period of time, strains your eyes.

• When using headphones, adjust the volume so as to avoid

excessive levels, as hearing damage may result.

LCD Screen

• Although the LCD screen is made with high-precision

technology and 99.99% or more of the pixels are effective,

black dots may appear or bright points of light (red, blue,

or green) may appear constantly on the LCD screen. This

is a structural property of the LCD screen and is not a

malfunction.

• Do not push or scratch the front filter, or place objects on

top of this TV set. The image may be uneven or the LCD

screen may be damaged.

• If this TV set is used in a cold place, a smear may occur in

the picture or the picture may become dark. This does not

indicate a failure. These phenomena disappear as the

temperature rises.

• Ghosting may occur when still pictures are displayed

continuously. It may disappear after a few moments.

• The screen and cabinet get warm when this TV set is in

use. This is not a malfunction.

• The LCD screen contains a small amount of liquid crystal

and mercury. The fluorescent tubes used in this TV set

also contains mercury. Follow your local ordinances and

regulations for disposal.

Handling and cleaning the screen surface/cabinet of

the TV set

Be sure to unplug the mains lead connected to the TV set

from mains socket before cleaning.

To avoid material degradation or screen coating degradation,

observe the following precautions.

• To remove dust from the screen surface/cabinet, wipe

gently with a soft cloth. If dust is persistent, wipe with a

soft cloth slightly moistened with a diluted mild detergent

solution.

• Never use any type of abrasive pad, alkaline/acid cleaner,

scouring powder, or volatile solvent, such as alcohol,

benzene, thinner or insecticide. Using such materials or

maintaining prolonged contact with rubber or vinyl

materials may result in damage to the screen surface and

cabinet material.

• When adjusting the angle of the TV set, move it slowly so

as to prevent the TV set from moving or slipping off from

its table stand

Optional Equipment

Keep optional components or any equipment emitting

electromagnetic radiation away from the TV set. Otherwise

picture distortion and/or noisy sound may occur.

010COV.book Page 8 Monday, July 23, 2007 12:08 PM

9

GB

Overview of the remote

1 "/1 – TV standby

Turns the TV on and off from standby mode.

2 A/B – Dual Sound (page 22)

3 Coloured buttons (page 12, 13, 15)

4 / – Input select / Text hold

• In TV mode: Selects the input source from equipment connected to the TV

sockets (page 17).

• In Text mode (page 12): Holds the current page.

5 F/f/G/g/

6 TOOLS (page 12, 18)

Enables you to access various viewing options and change/make adjustments

according to the source and screen format.

7 MENU (page 19)

8 THEATRE

You can set Theatre Mode on or off. When Theatre Mode is set to on,

the optimum audio output (if the TV is connected with an audio system using

an HDMI cable) and picture quality for film videos are automatically set.

9 Number buttons

• In TV mode: Selects channels. For channel numbers 10 and above, enter the

second and third digit quickly.

• In Text mode: Enters the three digit page number to select the page.

0 – Previous channel

Returns to the previous channel watched (for more than five seconds).

qa PROG +/-/ /

• In TV mode: Selects the next (+) or previous (-) channel.

• In Text mode (page 12): Selects the next ( ) or previous ( ) page.

qs % – Mute the sound

qd 2 +/- – Volume

qf / – Text (page 12)

qg DIGITAL – Digital mode (page 11)

qh ANALOG – Analogue mode (page 11)

qj RETURN /

Returns to the previous screen of any displayed menu.

qk – EPG (Digital Electronic Programme Guide) (page 13)

ql – Picture freeze (page 12)

Freezes the TV picture.

w; – Screen mode (page 12)

wa / – Info / Text reveal

• In digital mode: Displays brief details of the programme currently being

watched.

• In analogue mode: Displays information such as current channel number and

screen format.

• In Text mode (page 12): Reveals hidden information (e.g. answers to a quiz).

z

• The number 5, PROG + and A/B buttons have tactile dots. Use the tactile dots as

references when operating the TV.

• If you turn the TV off, Theatre Mode is also turned off.

010COV.book Page 9 Monday, July 23, 2007 12:08 PM

10

GB

Overview of the TV buttons and indicators

1 (page 19)

2 / – Input select / OK

• In TV mode: Selects the input source from

equipment connected to the TV sockets

(page 17).

• In TV menu: Selects the menu or option, and

confirms the setting.

3 2 +/-/ /

• In TV mode: Increases (+) or decreases (-) the

volume.

• In TV menu: Moves through the options right

( ) or left ( ).

4 PROG +/-/ /

• In TV mode: Selects the next (+) or previous

(-) channel.

• In TV menu: Moves through the options up

( ) or down ( ).

5 1 – Power

Turns the TV on or off.

~

To disconnect the TV completely, pull the plug

from the mains.

6 – Picture Off / Timer indicator

• Lights up in green when the picture is

switched off (page 24).

• Lights up in orange when the timer is set

(page 25).

7 1 – Standby indicator

Lights up in red when the TV is in standby mode.

8 " – Power / Timer REC programme

indicator

• Lights up in green when the TV is turned on.

• Lights up in orange when the timer recording

is set (page 13).

• Lights up in red during the timer recording.

9 Remote control sensor

• Receives IR signals from the remote.

• Do not put anything over the sensor, as its

function may be affected.

~

Make sure that the TV is completely turned off before

unplugging the mains lead. Unplugging the mains lead

while the TV is turned on may cause the indicator to

remain lit or may cause the TV to malfunction.

010COV.book Page 10 Monday, July 23, 2007 12:08 PM

11

GB

Watching TV

1 Press 1 on the TV (top side) to switch on

the TV.

When the TV is in standby mode (the 1 (standby)

indicator on the TV (front) is red), press "/1 on

the remote to switch on the TV.

2 Press DIGITAL to switch to digital mode or

ANALOG to switch to analogue mode.

The channels available vary depending on the

mode.

3 Press the number buttons or PROG +/- to

select a TV channel.

To select channel numbers 10 and above using the

number buttons, enter the second and third digits

within two seconds.

To select a digital channel using the Digital

Electronic Programme Guide (EPG), see page 13.

In digital mode

An information banner appears briefly. The

following icons may be indicated on the banner.

Additional operations

Watching TV

3

2

3

: Radio service

: Scrambled/Subscription service

: Multiple audio languages available

: Subtitles available

: Subtitles available for the hearing impaired

: Recommended minimum age for current

programme (from 4 to 18 years)

: Parental Lock

c: Current programme is being recorded

To Do this

Turn on the TV

from Standby mode

without sound

Press %. Press 2 +/- to set the

volume level.

Adjust the volume Press 2 + (increase)/

- (decrease).

Access the

Programme index

table (in analogue

mode only)

Press . To select an analogue

channel, press

F/f, then press

.

Continued

010COV.book Page 11 Monday, July 23, 2007 12:08 PM

12

GB

To access Text

Press /. Each time you press /, the display changes

cyclically as follows:

Text t Text over the TV picture (mix mode) t No

Text (exit the Text service)

To select a page, press the number buttons or PROG

+/-.

To hold a page, press / .

To reveal hidden information, press / .

z

When four coloured items appear at the bottom of the Text

page, Fastext is available. Fastext allows you to access pages

quickly and easily. Press the corresponding coloured button

to access the page.

Picture Freeze

Freezes the TV picture (e.g. to make a note of a

telephone number or recipe).

1 Press on the remote control.

2 Press F/f/G/g to adjust the position of the

window.

3 Press to remove the window.

4 Press again to return to normal TV

mode.

z

Not available for AV3, AV4, AV5 and PC

input.

To change the screen format manually to

suit the broadcast

Press repeatedly to select the desired screen

format.

* Parts of the top and bottom of the picture may be cut off.

~

• HD signal source pictures can only be displayed in

“Wide” mode .

• You cannot use this function while the digital banner is

displayed.

• Some characters and/or letters at the top and the bottom of

the picture may not be visible in Smart mode. In such a

case, you can select “V-Size” using the “Screen” menu

and adjust vertical size to make it visible.

z

• When “Auto Format” is set to “On”, the TV will

automatically select the best mode to suit the broadcast

(page 24).

• You can adjust the position of the picture when selecting

“Smart” (50Hz), “14:9” or “Zoom”. Press

F/f to move

up or down (e.g. to read subtitles).

Using the Tools menu

Press TOOLS to display the following options when

viewing a TV programme.

Smart*

Displays conventional

4:3 broadcasts with an

imitation wide screen

effect. The 4:3 picture

is stretched to fill the

screen.

4:3

Displays conventional

4:3 broadcasts (e.g.

non-wide screen TV) in

the correct proportions.

Wide

Displays wide screen

(16:9) broadcasts in the

correct proportions.

Zoom*

Displays cinemascopic

(letter box format)

broadcasts in the

correct proportions.

14:9*

Displays 14:9

broadcasts in the

correct proportions. As

a result, black border

areas are visible on the

screen.

Options Description

Close Closes the Tools menu.

Picture Mode See page 20.

Sound Effect See page 22.

Speaker See page 23.

Audio Language (in

digital mode only)

See page 30.

Subtitle Setting (in

digital mode only)

See page 30.

Sleep Timer See page 25.

Power Saving See page 24.

System Information (in

digital mode only)

Displays the system

information screen.

010COV.book Page 12 Monday, July 23, 2007 12:08 PM

13

GB

Watching TV

Checking the Digital Electronic Programme Guide

(EPG) *

1 In digital mode, press .

2 Perform the desired operation as shown in

the following table or displayed on the

screen.

~

Programme information will only be displayed if the TV

station is transmitting it.

* This function may not be available in some countries/regions.

Digital Electronic Programme Guide (EPG)

Select:

+/- 1 day on/off:

Options:

All Categories

To Do this

Watch a programme Press F/f/G/g to select the programme, then press .

Turn off the EPG Press .

Sort the programme information by

category

– Category list

1 Press the blue button.

2 Press

F/f/G/g to select a category, then press .

The categories available include:

“All Categories”: Contains all available channels.

Category name (e.g. “News”): Contains all channels corresponding to the

selected category.

Set a programme to be recorded

– Timer REC

1 Press F/f/G/g to select the future programme you want to

record, then press

/ .

2 Press

F/f to select “Timer REC”.

3 Press to set the TV and your VCR timers.

A red c symbol appears by that programme’s information. The

indicator on the TV front panel lights up in orange.

z

To record the programme you are currently watching, press / .

Set a programme to be displayed

automatically on the screen when it

starts

– Reminder

1 Press F/f/G/g to select the future programme you want to

display, then press

/ .

2 Press

F/f to select “Reminder”, then press .

A c symbol appears by that programme’s information. The indicator

on the TV front panel lights up in orange.

~

If you switch the TV to standby mode, it will automatically turn itself on

when the programme is about to start.

Continued

010COV.book Page 13 Monday, July 23, 2007 12:08 PM

14

GB

~

• You can set VCR timer recording on the TV only for SmartLink compatible VCRs. If your VCR is not SmartLink compatible,

a message will be displayed to remind you to set your VCR timer.

• Once a recording has begun, you can switch the TV to standby mode, but do not turn off the TV completely or the recording

may be cancelled.

• If an age restriction for programmes has been selected, a message asking for a PIN code will appear on the screen. For details,

see “Parental Lock” on page 30.

Set the time and date of a programme

you want to record

– Manual timer REC

1 Press F/f/G/g to select the future programme you want to

record, then press

/ .

2 Press

F/f to select “Manual timer REC”, then press .

3 Press

F/f to select the date, then press g.

4 Set the start and stop time in the same way as in step 3.

5 Press

F/f to select the programme, then press .

6 Press to set the TV and your VCR timers.

A red c symbol appears by that programme’s information. The

indicator on the TV front panel lights up in orange.

z

To record the programme you are currently watching, press / .

Cancel a recording/reminder

– Timer list

1 Press / .

2 Press

F/f to select “Timer list”, then press .

3 Press

F/f to select the programme you want to cancel, then

press .

4 Press

F/f to select “Cancel Timer”, then press .

A display appears to confirm that you want to cancel the programme.

5 Press G/g to select “Yes”, then press to confirm.

To Do this

010COV.book Page 14 Monday, July 23, 2007 12:08 PM

15

GB

Watching TV

Using the Digital Favourite list *

The Favourite feature allows you to specify up to four

lists of your favourite programmes.

1 Press MENU.

2 Press F/f to select “Digital Favourites”,

then press .

3 Perform the desired operation as shown in

the following table or displayed on the

screen.

* This function may not be available in some countries/regions.

Favourites 1

Favourites 2

Favourite Set-up Enter Programme number - - -

TV3

33

3/24

K3/300

TVE 1

TVE 2

24H TVE

CLAN TVE

TELEDEPORTE

VEO

011

012

013

014

015

016

017

018

019

020

SETenVEO

Tienda en VEO

NET TV

CUATRO

CNN+

40 LATINO

la Sexta

Telecinco

T5 Estrellas

T5 Sport

Back:

RETURN

Store favourite:

Digital Favourite list

To Do this

Create your Favourite list for the first

time

1 Press to select “Yes”.

2 Press yellow key to select favourite list.

3 Press

F/f to select the channel you want to add, then press .

Channels that are stored in the Favourite list are indicated by a symbol.

Watch a channel

1 Press yellow key to navigate through favourite lists.

2 Press

F/f to select the channel, then press .

Turn off the Favourite list

Press RETURN.

Add or remove channels in the currently

edited Favourite list

1 Press the blue button.

2 Press the yellow button to choose the list you want to edit.

3 Press

F/f to select the channel you want to add or remove,

then press .

Remove all channels from the current

Favourite list

1 Press the blue button.

2 Press the yellow button to select the favourite list you want to

edit.

3 Press the blue button.

4 Press

G/g to select “Yes”, then press to confirm.

010COV.book Page 15 Monday, July 23, 2007 12:08 PM

16

GB

Connecting optional equipment

You can connect a wide range of optional equipment to your TV. Connecting cables are not supplied.

Using Optional Equipment

6

For service

use only

S VHS/Hi8/

DVC camcorder

Headphones

DVD player with component output

DVD recorder

Decoder

VCR

Video game

equipment

DVD player

Decoder

PC

Audio system

PC (HDMI output)

Blu-ray disc player

Digital video camera

DVD player

Audio system

PC (HDMI output)

Blu-ray disc player

Digital video camera

DVD player

Hi-Fi audio equipment

CAM card

010COV.book Page 16 Monday, July 23, 2007 12:08 PM

17

GB

Using Optional Equipment

Viewing pictures from

connected equipment

Switch on the connected equipment, then

perform one of the following operation.

For equipment connected to the scart sockets using a

fully-wired 21-pin scart lead

Start playback on the connected equipment.

The picture from the connected equipment appears on

the screen.

For an auto-tuned VCR (page 6)

In analogue mode, press PROG +/-, or the number

buttons, to select the video channel.

For other connected equipment

Press / repeatedly until the desired input source

(see below) appears on the screen.

Additional operations

Symbol on the

screen

Description

AV1/ AV1

To see the equipment connected to I.

AV2/ AV2

To see the equipment connected to J.

~

SmartLink is a direct link between the

TV and a VCR/DVD recorder.

AV3 To see the equipment connected to H.

AV4 HDMI IN 4*.

To see the equipment connected to E.

AV5 HDMI IN 5*.

To see the equipment connected to D.

If the equipment has a DVI socket,

connect the DVI socket to the HDMI IN

socket through a DVI-HDMI adaptor

interface (not supplied), and connect the

equipment’s audio out sockets to the

audio in HDMI IN sockets.

* ~

• Be sure to use only an HDMI cable that bears the HDMI logo.

• When HDMI control compatible equipment is connected,

communication with the connected equipment is supported.

Refer to page 18 to set up this communication.

• When connecting an audio system with HDMI socket, be

sure to also connect to the HiFi socket.

AV6 or

AV 6

To see the equipment connected to B.

z

To avoid picture noise, do not connect

the camcorder to the video socket 6

and the S video socket 6 at the

same time. If you connect mono

equipment, connect to the L socket

6.

PC To see the equipment connected to F.

z

It is recommended to use a PC cable

with ferrites.

To connect Do this

Headphones A Connect to the i socket to listen to

sound from the TV on headphones.

Conditional

Access Module

(CAM) C

To use Pay Per View services.

For details, refer to the instruction

manual supplied with your CAM. To

use the CAM, remove the rubber cover

from the CAM slot. Switch off the TV

when inserting your CAM into the

CAM slot. When you do not use the

CAM, we recommend that you replace

the cover on the CAM slot.

~

CAM is not supported in all countries.

Please check with your authorized dealer.

Hi-Fi audio

equipment G

Connect to the audio output sockets

to listen to the sound from the TV

on Hi-Fi audio equipment.

To Do this

Return to normal TV

mode

Press DIGITAL or ANALOG.

Access the Input

signal index table

(except analog mode)

Press to access the Input

signal index table. To select an

input source, press

F/f, then

press .

Change the volume of

the connected HDMI

control compatible

audio system

Press

2 +/-.

Mute the sound of the

connected HDMI

control compatible

audio system

Press

%.

Press again to restore.

Symbol on the

screen

Description

Continued

010COV.book Page 17 Monday, July 23, 2007 12:08 PM

18

GB

Using the Tools menu

Press TOOLS to display the following options when

viewing pictures from connected equipment.

To view two pictures simultaneously

– PIP (Picture in Picture)

You can view two pictures (PC input and TV

programme) on the screen simultaneously.

Connect a PC (page 16), and make sure that images

from a PC appear on the screen.

~

You cannot display resolutions higher than WXGA (1280 ×

768 pixels).

1 Press TOOLS to display the Tools menu.

2 Press F/f to select “PIP”, then press .

The picture from the connected PC is displayed with

full size and the TV programme is displayed on the

right corner.

You can use

F/f/G/g to move the TV programme

screen position.

3 Press number buttons or PROG +/- to

select the TV channel.

To return to single picture mode

Press RETURN.

z

You can switch the audible picture by selecting “PC Sound/

TV Sound” from the Tools menu.

Using HDMI control

The HDMI control function allows equipment to

control each other using HDMI CEC (Consumer

Electronics Control) specified by HDMI.

You can perform interlocked control operations

between Sony HDMI control compatible equipment

such as a TV, DVD recorder with hard disk and audio

system by connecting the equipment with HDMI

cables.

Be sure to correctly connect and set the compatible

equipment to use the HDMI control function.

To connect the HDMI control compatible

equipment

Connect the compatible equipment and the TV with an

HDMI cable. When connecting an audio system, in

addition to the HDMI cable, be sure to also connect

the audio output socket

of the TV and the audio

system. For details, see page 16.

To make the HDMI control settings

HDMI control must be set on both the TV side and the

connected equipment side. See HDMI Set-up

(page 27) for the TV side settings. See the operating

instructions of the connected equipment for setting

details.

HDMI control functions

• Turns the connected equipment off interlocked with

the TV.

• Turns the TV on interlocked with the connected

equipment and automatically switches the input to

the equipment when the equipment starts to play.

• If you turn on a connected audio system while the

TV is on, the input switches to the audio from the

audio system.

• Adjusts the volume and mutes the sound of a

connected audio system.

Options Description

Close Closes the Tools menu.

Picture Mode (except

PC input mode)

See page 20.

Display Mode (in PC

input mode only)

See page 20.

Sound Effect See page 22.

Speaker See page 23.

PIP (in PC input

mode only)

See page 18.

H Centre (in PC input

mode only)

See page 25.

V Lines (in PC input

mode only)

See page 25.

Sleep Timer (except

PC input mode)

See page 25.

Power Saving See page 24.

010COV.book Page 18 Monday, July 23, 2007 12:08 PM

19

GB

Using MENU Functions

Navigating through

menus

“MENU” allows you to enjoy various convenient

features of this TV. You can easily select channels or

inputs sources and change the settings for your TV.

1 Press MENU.

2 Press F/f to select an option, then press

.

To exit the menu, press MENU.

1 Digital Favourites*

Displays the Favourite list. For details about

settings, see page 15.

2 Analogue

Returns to the last viewed analogue channel.

3 Digital*

Returns to the last viewed digital channel.

4 Digital EPG*

Displays the Digital Electronic Programme

Guide (EPG).

For details about settings, see page 13.

5 External Inputs

Selects equipment connected to your TV.

• To watch the desired external input, select the

input source, then press .

6 Settings

Displays the Settings menu where most of the

advanced settings and adjustments are

performed.

1 Press F/f to select a menu icon, then

press .

2 Press

F/f/G/g to select an option or

adjust a setting, then press .

For details about settings, see page 20 to 30.

~

The options you can adjust vary depending on the

situation. Unavailable options are greyed out or not

displayed.

* This function may not be available in some countries

/

regions.

Using MENU Functions

2

1

Select:

Enter:

Exit:

MENU

Digital Favourites

010COV.book Page 19 Monday, July 23, 2007 12:08 PM

20

GB

Picture Adjustment menu

You can select the options listed below on the

Picture menu. To select options in “Settings”,

see “Navigating through menus” (page 19).

Picture Mode

Display Mode

(only in

PC mode)

Selects the picture mode except for PC input source.

“Vivid”: For enhanced picture contrast and sharpness.

“Standard”: For standard picture. Recommended for home entertainment.

“Cinema”: For viewing film-based content. Most suitable for viewing in a theatre-

like environment. This picture setting was developed in collaboration with Sony

Pictures Entertainment to faithfully reproduce movies as intended by their creators.

Selects the display mode for PC input source.

“Video”: For video images.

“Text”: For text, charts or tables.

Backlight

Adjusts the brightness of the backlight.

Contrast

Increases or decreases picture contrast.

Brightness

Brightens or darkens the picture.

Colour

Increases or decreases colour intensity.

Hue

Increases or decreases the green tones.

z

“Hue” can only be adjusted for an NTSC colour signal (e.g., U.S.A. video tapes).

Sharpness

Sharpens or softens the picture.

Colour Tone

Adjusts the whiteness of the picture.

“Cool”: Gives the white colours a blue tint.

“Neutral”: Gives the white colours a neutral tint.

“Warm”: Gives the white colours a red tint.

z

“Warm” can not be selected when you set “Picture Mode” to “Vivid”.

Picture Adjustment

Select:

Enter:

Exit:

MENU

Picture Mode

Backlight

Contrast

Brightness

Colour

Hue

Sharpness

Colour Tone

Noise Reduction

Advanced Settings

Reset

Cinema

5

Max

50

0

15

Warm

Auto

Back:

010COV.book Page 20 Monday, July 23, 2007 12:08 PM

Stránka sa načítava ...

Sony KDL-32S2800 Návod na obsluhu

Táto príručka je tiež vhodná pre

Sony KDL-32S2800 Návod na obsluhu

V iných jazykoch

Súvisiace články

Ďalšie dokumenty