Simplicity SINGLE STAGE SNOWTHROWER Používateľská príručka

Instruction Book - Snowthrower Model 6210701x61NA

Manuel de l’utilisateur -- Chasse-neige modèle 6210701x61NA

Betriebsanleitung -- Schneeschleuder modell 6210701x61NA

Manuale di istruzioni - Spalaneve meccanico modello 6210701x61NA

Instruktieboek -- Sneeuwblazer model 6210701x61NA

Instruktionsbog -- Sneslynge model 6210701x61NA

Bruksanvisning -- Snøfreser modell 6210701x61NA

Användarhandbok - Snöslunga modell 6210701x61NA

Ohjekirja -- Lumilinko malli 6210701x61NA

Manual de instrucciones -- Quitanieves modelo 6210701x61NA

Kasutusjuhend - Lumekoristaja mudel 6210701x61NA

âéâëßï Ïóçãéþv — Åê÷éïíéóôÞñá ÌïíôÝëï 6210701x61NA

Kezelési útmutató - Hómaró modell 6210701x61NA

Lietošanas instrukciju -

6QLHJD SĭWÕMV PRGHOLV

6210701x61NA

Instrukcija - Sniego valymo mašina rengims modelis 6210701x61NA

Instrukcja obsugi -Odœnie¿arka model 6210701x61NA

Návod na používanie — Snehová fréza, model 6210701x61NA

Návod na obsluhu —Snežá fréza, model 6210701x61NA

Knjižica z navodili — Snežná fréza, model 6210701x61NA

Ðóêîâîäñòâî ïî ýêñïëóàòàöèè – Ñíåãîî÷èñòèòåëü Ìîäåëü 6210701x61NA

fr

de

it

nl

da

no

sv

fi

en

es

et

el

hu

lv

lt

pl

TP 199-4667-04-SW-R

cs

sk

1741416

sl

ru

2

1741416

2

3

5

8

12

9

4

14

1

22

3

1741416

2

1

2

3

x

1

4

1

x

5

1

2

4

1741416

1

22

6

1

7

5

2

1

7

89

1111

1

2

22

2

4

3

10

2

3

1

44 511

3

4

5

1741416

12

12 13

1

23

4

1

3

14

2

4

5

6

15

1

16

1

7

9

8

17

6

1741416

1

7

6

18

3

4

5

2

8

9

91010

11

19

11

6

20

1

2

en

7

1741416

CONTENTS

HAZARD SYMBOLS AND THE MEANINGS 8..........

OPERATING SYMBOLS AND THEIR MEANINGS 8.....

RULES FOR SAFE OPERATION 9....................

ASSEMBLY 11......................................

OPERATION 11.....................................

MAINTENANCE 13..................................

MAINTENANCE CHART 13...........................

TROUBLE SHOOTING CHART 15.....................

LIMITED WARRANTY 16.............................

General Information

This instruction book is written for a person with some mechanical ability.

Like most service books, not all the steps are described. Steps on how to

loosen or tighten fasteners are steps anyone can follow with some

mechanical ability. Read and follow these instructions before you use the

unit.

Know your product: If you understand the unit and how the unit

operates, you will get the best performance. As you read this manual,

compare the illustrations to the unit. Learn the location and the function of

the controls. To help prevent an accident, follow the operating instructions

and the safety rules. Keep this manual for future reference.

IMPORTANT: Many units are not assembled and are sold in cartons. It is

the responsibility of the owner to make sure the assembly instructions in

this manual are exactly followed. Other units are purchased in an

assembled condition. On assembled units, it is the responsibility of the

owner to make sure the unit is correctly assembled. The owner must

carefully check the unit according to the instructions in this manual before

it is first used.

Controls & Equipment Features (see Figure 1)

Crank Assembly (2) -- Changes the direction of the discharge chute.

Chute Deflector (3) -- Changes the distance the snow is thrown.

Discharge Chute (4) -- Changes the direction the snow is thrown.

Auger Drive Lever (5) -- Starts and stops the auger (snow gathering and

throwing) which also propels the snowthrower..

Engine Features

Stop Switch (8) -- If equipped, move to the ON position to start the

engine.

Primer Button (9) -- Injects fuel directly into the carburetor for fast starts

in cold weather.

Recoil Starter Handle (12) -- Use to manually start the engine.

Choke Control (14) -- Use to start a cold engine.

en

8

1741416

This manual contains safety information to make you

aware of the hazards and risks associated with snow

throwers, and how to avoid them. The snow thrower is designed and

intended for removal of snow, and should not be used for any other

purpose. It is important that you read and understand these

instructions, and anyone operating the equipment read and understand

these instructions.

The engine exhaust from this product contains chemicals known to the

State of California to cause cancer, birth defects, or other reproductive

harm.

WARNING

A signal word (DANGER, WARNING, or CAUTION) is used with the alert

symbol to indicate the likelihood and the potential severity of injury. In

addition, a hazard symbol may be used to represent the type of hazard.

DANGER indicates a hazard which, if not avoided, will result in

death or serious injury.

WARNING indicates a hazard which, if not avoided, could result

in death or serious injury.

CAUTION indicates a hazard which, if not avoided, might result

in minor or moderate injury.

CAUTION, when used without the alert symbol, indicates a

situation that could result in damage to the equipment.

Hazard Symbols and the meanings

These symbols are used on your equipment and defined in your operating

manual. Review and understand the meanings. The use of one of these

symbols combined with a signal word will alert you to potential hazards

and how to avoid them.

Explosion

Toxic fumes Shock

Hot Surface

Fire

Operator’s Manual -- Read and understand before

performing any activity or running equipment.

Safety Alert -- Identifies safety information about

hazards that can result in personal injury.

Rotating auger

Rotating impeller

Rotating gears

Thrown objects

Keep a safe distance

from the equipment.

Shut off engine and remove spark plug connector

before performing maintenance or repair work.

Never reach into

rotating parts.

Recommended ear

protection for extended

use.

Operating Symbols and their meanings

These symbols are used on your equipment and defined in your operating

manual. It is important that you review and understand the meanings.

Failure to understand the symbols might result in harm to you.

Stop

Fuel

Choke off

Oil

Choke on

Slow

Fast

On Off

Ignition Key

Ignition Off

Ignition On

Primer bulb

Throttle

Drive Clutch

Auger Clutch

Engage

RIGHT

Auger Collector

Traction

Discharge Chute

LEFT UP DOWN

Foward

Neutral

Reverse

Push to engage

electric start

Electric

Start

Engine

Start

Engine Run

Engine Off

Chute Deflector

Engage

Disengage

Heated Grips

Engage

en

9

1741416

WARNING: This machine is capable of amputating hands and feet and throwing objects. Read these safety rules

and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or

death to you, or bystanders, or damage to property or equipment. The triangle in text signifies important cau-

tions or warnings which must be followed.

Safe Operation Practices for Snowthrowers

IMPORTANT: Safety standards require operator presence controls to

minimize the risk of injury. Your snowthrower is equipped with such con-

trols. Do not attempt to defeat the function of the operator presence con-

trol under any circumstances.

Training

1. Read, understand, and follow all instructions on the machine and in the

manuals before operating this unit. Be thoroughly familiar with the con-

trols and the proper use of the equipment. Know how to stop the unit

and disengage the controls quickly.

2. Never allow children to operate the equipment. Never allow adults to

operate the equipment without proper instruction.

3. Keep the area of operation clear of all persons, particularly small

children and pets.

4. Exercise caution to avoid slipping or falling especially when operating in

reverse.

Preparation

1. Thoroughly inspect the area where the equipment is to be used and

remove all doormats, sleds, boards, wires, and other foreign objects.

2. Disengage all clutches and shift into neutral before starting the engine

(motor).

3. Do not operate the equipment without wearing adequate winter outer

garments. Wear footwear that will improve footing on slippery surfaces.

Avoid loose fitting clothing that can get caught in moving parts.

4. Handle fuel with care; it is highly flammable.

a. Use an approved fuel container.

b. Never add fuel to a running engine or hot engine.

c. Fill fuel tank outdoors with extreme care. Never fill fuel tank indoors.

Replace fuel cap securely and wipe up spilled fuel.

d. Never fill containers inside a vehicle or on a truck or trailer bed with

a plastic liner. Always place containers on the ground, away from

your vehicle, before filling.

e. When practical, remove gas--powered equipment from the truck or

trailer and refuel it on the ground. If this is not possible, then refuel

such on a trailer with a portable container, rather than from a gaso-

line dispenser nozzle.

f. Keep nozzle in contact with the rim of the fuel tank or container

opening at all times, until refueling is complete. Do not use a nozzle

lock--open device.

g. Replace gasoline cap securely and wipe up spilled fuel.

h. If fuel is spilled on clothing, change clothing immediately.

5. Use extension cords and receptacles as specified by the manufactur-

er for all units with electric drive motors or electric starting motors.

6. Adjust the collector housing height to clear gravel or crushed rock

surfaces.

7. Never attempt to make any adjustments while the engine (motor) is

running (except when specifically recommended by manufacturer).

8. Let engine (motor) and snowthrower adjust to outdoor temperatures

before starting to clear snow.

9. Always wear safety glasses or eye shields during operation or while

performing an adjustment or repair to protect eyes from foreign objects

that may be thrown from the machine.

Operation

1. Do not put hands or feet near or under rotating parts. Keep clear of the

discharge opening at all times.

2. Exercise extreme caution when operating on or crossing gravel drives,

walks or roads. Stay alert for hidden hazards or traffic.

3. After striking a foreign object, stop the engine (motor), remove the wire

from the spark plug, disconnect the cord on electric motors, thoroughly

inspect snowthrower for any damage, and repair the damage before

restarting and operating the snowthrower.

4. If the unit should start to vibrate abnormally, stop the engine (motor)

and check immediately for the cause. Vibration is generally a warning

of trouble.

5. Stop the engine (motor) whenever you leave the operating position,

before unclogging the collector/impeller housing or discharge chute and

when making any repairs, adjustments, or inspections.

6. When cleaning, repairing, or inspecting, make certain the collector/im-

peller and all moving parts have stopped. Disconnect the spark plug

wire and keep the wire away from the spark plug to prevent accidental

starting.

7. Do not run the engine indoors, except when starting the engine and for

transporting the snowthrower in or out of the building. Open the outside

doors; exhaust fumes are dangerous (containing CARBON MONOX-

IDE, an ODORLESS and DEADLY GAS).

8. Exercise extreme caution when operating on slopes. Do not attempt to

clear steep slopes.

9. Never operate the snowthrower without proper guards, plates, or other

safety protective devices in place and working.

10. Never direct the discharge toward people or areas where property

damage can occur. Keep children and others away.

11. Do not overload the machine capacity by attempting to clear snow at

too fast a rate.

12. Never operate the machine at high transport speeds on slippery sur-

faces. Look behind and use care when operating in reverse.

13. Disengage power to the collector/impeller when snowthrower is trans-

ported or not in use.

14. Use only attachments and accessories approved by the manufacturer

of the snowthrower (such as cabs, tire chains, etc..).

15. Never operate the snowthrower without good visibility or light. Always

be sure of your footing and keep a firm hold on the handles. Walk,

never run.

16. Never touch a hot engine or muffler.

17. Never operate the snowthrower near glass enclosures, automobiles,

window wells, drop--offs, and the like without proper adjustment of the

snow discharge angle.

18. Never direct discharge at bystanders or allow anyone in front of the

unit.

19. Never leave a running unit unattended. Always disengage the auger

and traction controls, stop engine, and remove keys.

20. Do not operate the unit while under the influence of alcohol or drugs.

21. Keep in mind the operator is responsible for accidents occurring to

other people or property.

22. Data indicates that operators, age 60 years and above, are involved

in a large percentage of power equipment--related injuries. These

operators should evaluate their ability to operate the unit safely

enough to protect themselves and others from injury.

23. DO NOT wear long scarves or loose clothing that could become

entangled in moving parts.

24. Snow can hide obstacles. Make sure to remove all obstacles from

the area to be cleared.

en

10

1741416

Children

Tragic accidents can occur if the operator is not alert to the presence of chil-

dren. Children are often attracted to the unit and the operating activity. Never

assume that children will remain where you last saw them.

1. Keep children out of the area and under the watchful care of another

responsible adult.

2. Be alert and turn off if children enter the area.

3. Never allow children to operate the unit.

4. Use extra care when approaching blind corners, shrubs, trees, or

other objects that may obscure vision.

Clearing A Clogged Discharge Chute

Hand contact with the rotating impeller inside the discharge chute is the

most common cause of injury associated with snowthrowers. Never use

your hand to clean out the discharge chute.

To clear the chute:

1. SHUT OFF THE ENGINE.

2. Wait 10 seconds to be sure the impeller blades have stopped rotating.

3. Always use a clean out tool, not your hands.

Service, Maintenance And Storage

1. Check shear bolts and other bolts at frequent intervals for proper tight-

ness to be sure the equipment is in safe working condition.

2. Never store the machine with fuel in the tank inside a building where

ignition sources are present such as hot water and space heaters, or

clothes dryers. Allow the engine to cool before storing in any enclosure.

3. Always refer to operator’s manual for important details if the snow-

thrower is to be stored for an extended period.

4. Maintain or replace safety and instruction labels as necessary.

5. Run the machine a few minutes after throwing snow to prevent freeze--

up of the collector/impeller.

6. If fuel is spilled, do not attempt to start the engine but move the ma-

chine away from the area of spillage and avoid creating any source of

ignition until fuel vapors have dissipated.

7. Always observe safe refueling and fuel handling practices when re-

fueling the unit after transportation or storage.

8. Always follow the engine’s manual instructions for storage preparations

before storing the unit for both short and long term periods,

9. Always follow the engine manual instructions for proper start-up pro-

cedures when returning the unit to service.

10. Maintain or replace safety and instruction labels as necessary.

11. Keep nuts and bolts tight and keep equipment in good condition.

12. Never tamper with safety devices. Check their proper operation regular-

ly and make necessary repairs if they are not functioning properly.

13. Components are subject to wear, damage, and deterioration. Frequent-

ly check components and replace with manufacturer’s recommended

parts, when necessary.

14. Check control operation frequently. Adjust and service as required.

15. Use only factory authorized replacement parts when making repairs.

16. Always comply with factory specifications on all settings and adjust-

ments.

17. Only authorized service locations should be utilized for major service

and repair requirements.

18. Never attempt to make major repairs on this unit unless you have been

properly trained. Improper service procedures can result in hazardous

operation, equipment damage and voiding of manufacturer’s warranty.

19. Check shear bolts (pins) and other bolts at frequent intervals for proper

tightness to be sure the equipment is in safe working condition.

Emissions

1. Engine exhaust from this product contains chemicals known, in certain

quantities, to cause cancer, birth defects, or reproductive harm.

2. If available, look for the relevant Emissions Durability Period and Air

Index information on the engine emissions label.

Ignition System

1. This spark ignition system complies with Canadian ICES-002.

en

11

1741416

ASSEMBLY

Read and follow the assembly and adjustment

instructions for your snow thrower. All fasteners

are in the parts bag. Do not discard any parts or

material until the unit is assembled.

WARNING: Before doing any as-

sembly or maintenance to the snow

thrower, remove the wire from the

spark plug.

NOTE: In this instruction book, left and right

describe the location of a part from the oper-

ator’s position behind the unit.

NOTE: Torque is measured in foot pounds

(metric N.m). This measurement describes

how tight a nut or bolt must be. The torque is

measured with a torque wrench.

NOTE: Illustrations are located on page 2

and on pages 3 through 6.

Tools Required

1 Knife

1 Pliers

How To Remove The Snow Thrower

From The Carton

1. Locate and remove the container of oil.

2. Locate all parts that are packed separately

and remove from the carton.

3. Remove and discard the packing material

from around the snow thrower.

4. Cut down all four corners of the carton and

lay the side panels flat.

5. Hold onto the lower handle and pull the snow

thrower off the carton.

CAUTION: DO NOT back over cables.

6. Remove the packing material from handle

assembly. Remove the lower insert from the

axle.

How To Assemble The Handle

1. Remove the packing material from the upper

and lower handles.

2. (Figure 2) Loosen the knobs (1) on each

side of the handle (2).

3. Raise the upper handle (2) to the operating

position. Hold the upper handle (2) apart to

prevent scratching the lower handle.

NOTE: Make sure the auger drive cable is

not caught between the upper and lower

handle.

4. Tighten the knobs (1).

How To Prepare The Engine

WARNING: Follow the engine

manufacturer’s instructions for the

type of fuel and oil to use. Always

use a safety fuel container. Do not smoke

when adding fuel to the fuel tank. When

inside an enclosure, do not fill the fuel

tank. Before you add the fuel, stop the en-

gine. Let the engine cool for several min-

utes.

See the engine manufacturer’s instructions for

the type of fuel and oil to use. Before you use

the unit, read the information on safety, opera-

tion, maintenance, and storage.

NOTE: Engine horsepower ratings may vary

by engine adjustments, manufacturing vari-

ances, altitude, atmospheric conditions, fuel

and maintenance.

Add Oil To The Engine (Figure 3)

NOTE: Engine may already contain some

residual oil. Check frequently when filling

the crankcase. DO NOT overfill.

The snow thrower was shipped with a container

of 5W30 motor oil. This oil must be added to the

engine before operating.

1. Make sure the unit is level.

2. Remove the oil fill cap/dipstick (1) and fill

the crankcase to “FULL” line on dipstick. DO

NOT overfill.

3. Tighten the oil fill cap/dipstick (1) securely

each time you check the oil level.

NOTE: Synthetic oil can assist with starting

in extreme cold temperatures. Synthetic

5W30 is acceptable for all temperatures. DO

NOT mix oil with petrol.

Add Petrol To The Engine

This engine is certified to operate on petrol. Ex-

haust Emission Control System: EM (Engine

Modifications).

WARNING: Alcohol blended fuels

(called gasohol or those using

ethanol or methanol) can attract

moisture which leads to separation and

formation of acids during storage. Acidic

gas can damage the fuel system of an en-

gine while in storage.

NOTE: To avoid engine problems, the fuel

system must be emptied before storage for

30 days or longer. Start the engine and let it

run until the fuel lines and carburetor are

empty. Use fresh fuel next season. See the

Storage section in this manual for additional

information.

Fill the fuel tank only with a fresh, clean, un-

leaded regular, unleaded premium, or reformu-

lated automotive petrol with a minimum of 85

octane. DO NOT use leaded petrol. Make sure

that the container you pour the petrol from is

clean and free from rust or other foreign par-

ticles. Never use petrol that may be stale from

long periods of storage in the container.

Before You Operate

Before you operate your new snow thrower,

please review the following checklist:

GMake sure all assembly instructions have

been completed.

GMake sure the discharge chute rotates freely.

GMake sure that no loose parts remain in the

carton.

As you learn how to properly use the snow

thrower, pay extra attention to the following im-

portant items.

GMake sure the engine oil is at the proper

level. For the type engine oil to use, see the

Engine Manufacturer’s manual.

GMake sure gas tank is filled properly with

clean, fresh, unleaded petrol with a minimum

of 85 octane.

GBecome familiar with the location of all

controls and understand their function.

GBefore starting the engine, make sure all

controls operate correctly.

OPERATION

NOTE: Illustrations are located on page 2

and on pages 3 through 6.

CAUTION: Use only attachments and acces-

sories approved by the manufacturer of the

snow thrower (such as tire chains, electric

start kits, etc.).

Know Your Snow Thrower (Figure 1)

Read this Instruction Book and safety rules be-

fore operation the snow thrower. Compare the

illustration with your snow thrower to familiarize

yourself with the location of various controls and

adjustments.

How To Control

The Discharge Of The Snow

WARNING: Never direct the dis-

charge of snow toward bystanders.

WARNING: Always stop the engine

before unclogging the discharge

chute or the auger housing and be-

fore leaving the snow thrower.

1. (Figure 1) Turn the crank assembly (2) to

change the discharge direction of the snow.

2. (Figure 6) Loosen the wing knob (1) on the

chute deflector (2).

3. Move the chute deflector (2) up for more

distance or down for less distance.

4. Tighten the wing knob (1).

How To Throw Snow (Figure 1)

1. Engage the auger drive lever (5).

2. To stop throwing snow, release the auger

drive lever (5).

WARNING: The operation of any

snow thrower can result in foreign

objects being thrown into the eyes,

which can result in severe eye damage.

Always wear safety glasses or eye shields

while operating the snow thrower. We rec-

ommend standard safety glasses or use a

wide vision safety mask over your glasses.

How To Stop Discharging Snow

(Figure 1)

1. To stop discharging snow, release the auger

drive lever (5).

NOTE: If the snow thrower continues to

slowly move forward, see “How To Adjust

The Auger Control Cable” in the Mainte-

nance Section.

2. To stop the engine, push the stop switch (8)

to the off position.

CAUTION: To stop the engine, do not move

the choke control to CHOKE position. Back-

fire or engine damage can occur.

en

12

1741416

How To Move Forward (Figure 7)

1. Hold the auger drive lever (5) against the

handle (2). The auger will begin rotating.

2. To go forward, raise the handle (2) to allow

the rubber auger blades to contact the

ground. Maintain a firm hold on the handle

(2) as the snow thrower starts to move for-

ward. Guide the snow thrower by moving the

handle (2) either left or right. Do not attempt

to push the snow thrower.

3. To stop, release the auger drive lever (5).

NOTE: If the auger continues to rotate, see

“How To Adjust The Auger Control Cable” in

the Maintenance section.

Before Starting The Engine

1. Before you service or start the engine, famil-

iarize yourself with the snow thrower. Be

sure you understand the function and loca-

tion of all controls.

2. Make sure that all fasteners are tight.

3. Make sure gas tank is filled properly with

clean, fresh, unleaded petrol with a minimum

of 85 octane.

4. Become familiar with the location of all con-

trols and understand their function.

5. Before starting the engine, make sure all

controls operate corrently.

How To Stop The Engine (Figure 1)

To stop the engine, push the stop switch (8) to

the off position.

CAUTION: To stop the engine, do not move

the choke control to CHOKE position. Back-

fire or engine damage can occur.

How To Start The Engine (Figure 1)

Make sure that the engine oil is at FULL mark on

dipstick. The engine is equipped with a recoil

starter. Before starting the engine, make certain

that you have read the following information.

If engine floods, set the choke to the OPEN/

RUN position and crank until the engine starts.

WARNING: Rapid retraction of the

starter cord (kickback) will pull

your hand or arm toward the en-

gine faster than you can let go of the start-

er cord.

S

When starting the engine, slowly pull

the starter cord until resistance is felt.

Then, rapidly pull the starter cord.

S

Make sure components; such as impel-

lors, pulleys or sprockets, are securely

attached.

How To Start A Cold Engine (Figure 1)

1. (Figure 1) Push the stop switch (8) to the

ON position.

2. When starting the engine, do not engage the

auger drive lever.

3. Move the choke control (14) to the FULL

choke position.

4. Push the primer button (9) two times. Re-

move finger from the primer button (9) be-

tween primes.

5. (Figure 4) Slowly pull the recoil starter han-

dle (1) until resistance is felt and then pull

rapidly to start the engine. Do not allow the

recoil starter handle (1) to snap back. Slow-

ly return the recoil starter handle (1).

NOTE: In temperatures below 0

q

F, allow

the engine to warm up for several minutes

before blowing snow.

WARNING: Never run the engine

indoors or in enclosed, poorly ven-

tilated areas. Engine exhaust con-

tains carbon monoxide, an odorless and

deadly gas. Keep hands, feet, hair and

loose clothing away from any moving parts

located on the engine or the snow thrower.

The temperature of muffler and nearby

areas may exceed 150qF. Avoid these

areas.

How To Start A Warm Engine (Figure 1)

If an engine has been running and is still warm,

leave the choke control (14) in the off position

and do not push the primer button (9).Ifthe

engine fails to start, follow the instructions “How

To Start A Cold Engine”.

NOTE: Do not use the primer button (9) to

start a warm engine.

How To Start An Engine With A Frozen Electric

Starter (Figure 1)

If the starter is frozen and will not turn the en-

gine, follow the instructions below.

1. Pull out the recoil starter handle (12) as far

as possible.

2. Quickly release the recoil starter handle

(12). Allow the recoil starter handle (12) to

snap back against the recoil starter.

If the engine still fails to start, repeat the two pre-

vious steps until the engine starts. Then, contin-

ue with the directions “How To Start A Cold

Engine”.

To help prevent the possible freeze--up of the

recoil starter and of the engine controls, proceed

as follows after each snow removal job.

1. Before storing, run the snow thrower a few

minutes to prevent freeze--up of the auger/

impeller.

2. With engine off, allow engine to cool for sev-

eral minutes.

3. Pull starter rope very slowly until resistance

is felt, then stop. Allow the starter rope to re-

coil. Repeat three times.

4. With the engine not running, wipe all snow

and moisture from the carburetor cover in

area of controls and levers. Also, move the

choke control and starter handle several

times.

How To Remove Snow or Debris From

The Auger Housing (Figure 1)

WARNING: Do not attempt to re-

move snow or debris that may be-

come lodged in auger housing

without taking the following precautions.

1. Release the auger drive lever (5).

2. To stop the engine, move the stop switch

(8) to the stop position.

3. Disconnect the spark plug wire.

4. Do not place your hands in the auger hous-

ing (22) or the discharge chute (4).Usea

pry bar to remove any snow or debris.

Snow Throwing Tips

1. This snow thrower will propel itself forward

when the handle is raised enough to cause

the auger blades to contact the ground. The

auger should stop when auger control bar is

released. If it does not stop, see “How To Ad-

just The Auger Control Cable” in the adjust-

ment section.

2. Most efficient snow throwing is accomplished

when the snow is removed immediately after

if falls.

CAUTION: Do not overload the machine ca-

pacity by attempting to clear snow at too fast

a rate.

3. For complete snow removal, slightly overlap

each previous path.

4. Whenever possible, discharge the snow

down wind.

5. The distance the snow will be discharged

can be adjusted by moving the discharge

chute deflector. Raise the deflector for more

distance or lower the deflector for less dis-

tance.

6. In windy conditions, lower the chute deflector

to direct the discharged snow close to the

ground where it is less likely to blow into un-

wanted areas.

7. For safety and to prevent damage to the

snow thrower, keep the area to be cleared

free of stones, toys and other foreign objects.

8. Do not use the auger propelling feature when

clearing gravel or crushed rock driveways.

Move the handle down to slightly raise the

auger.

9. The forward speed of the snow thrower is

dependent on the depth and weight of the

snow. Experience will establish the most ef-

fective method of using the snow thrower un-

der different conditions.

10.After each snow throwing job, allow the en-

gine to run for a few minutes. The snow and

accumulated ice will melt off the engine.

11. Clean the snow thrower after each use.

12.Remove ice, snow and debris from the entire

snow thrower. Flush with water to remove all

salt or other chemicals. Wipe snow thrower

dry.

Dry And Average Snow

1. Snow up to eight inches deep can be re-

moved rapidly and easily by walking at a

moderate rate. For snow or drifts of a greater

depth,slow your pace to allow the discharge

chute to dispose of the snow as rapidly as

the auger receives the snow.

2. Plan to have the snow discharged in the di-

rection the wind is blowing.

Wet Packed Snow

Move slowly into wet, packed snow. If the wet,

packed snow causes the auger to slow down or

the discharge chute begins to clog, back off and

begin a series of short back and forth jabs into

the snow. These short back and forth jabs, four

to six inches, will “belch” the snow from the

chute.

Snow Banks And Drifts

In snow of greater depth than the unit, use the

same “jabbing” technique described above. Turn

the discharge chute away from the snow bank.

More time will be required to remove snow of

this type than level snow.

en

13

1741416

MAINTENANCE CHART

CUSTOMER RESPONSIBILITIES

SERVICE RECORDS

Fill in dates as you

complete regular

service.

Before

Each

Use

First

2

Hours

Every

5

Hours

Every

10

Hours

Every

25

Hours Each

Season Before

Storage SERVICE DATES

Check And Tighten All Screws and Nuts  

Check Spark Plug  

Check Drive Belt 

Check Fuel 

Drain Fuel 

Lubricate Chute Control Flange 

Check Adjustment of Auger Control Cable 

Auger Drive Belt 

MAINTENANCE

NOTE: Illustrations are located on page 2

and on pages 3 through 6.

Use the following maintenance section to keep

your unit in good operating condition.

All the maintenance information for the engine is

in the engine manufacturer’s instructions. Before

you start the engine, read this book.

WARNING: Before you make an in-

spection, adjustment (except

carburettor), or repair, disconnect

the wire from the spark plug.

Emissions Control

Maintenance, replacement, or repair of the

emissions control devices and systems may

be performed by any non--road engine repair

establishment or individual. However, to ob-

tain a “no charge” emissions control service, the

work must be performed by a factory authorized

dealer. See the Emissions Warranty.

General Recommendations

The warranty on this snow thrower does not cov-

er items that have been subjected to operator

abuse or negligence. To receive full value from

the warranty, the operator must maintain the

snow thrower as instructed in this manual.

Some adjustments must be made periodically to

properly maintain the snow thrower.

After Each Use

GCheck for any loose or damaged parts.

GTighten any loose fasteners.

GCheck and maintain the auger.

GCheck controls to make sure they are

functioning properly.

GIf any parts are worn or damaged, replace

immediately.

GCheck all safety and instruction decals and

labels. Replace any decals or labels that are

missing or cannot be clearly read.

All adjustments in the Maintenance section of

this manual should be checked at least once

each season.

How To Remove The Top Cover

(Figure 8)

1. Remove the five screws (1) from the top

cover (2).

2. Remove the top cover (2).

3. To install the top cover (4), reverse the

above steps.

Lubrication

Before Storage (Figure 8)

1. Lubricate the clute control flange (7). Apply

a clinging type of grease such as Lubriplate.

How To Adjust The Auger Control Cable

The auger control cable is adjusted at the facto-

ry. During normal use, the auger control cable

can become stretched and the auger drive lever

will not properly engage or disengage the auger.

1. (Figure 12) Loosen the nut (1) that holds the

cable tension spring (2).

2. Slide the cable tension spring (2) toward

the rear of the unit until all cable slack is re-

moved.

NOTE: The auger control cable is properly

adjusted when the free cable slack is re-

moved and there is no tension on the

idler arm.

3. Tighten the nut (1) that holds the cable ten-

sion spring (2).

If belt stretch has occured, move the end the

auger control cable to the outside hole as fol-

lows:

1. (Figure 12) Loosen the nut (1) that holds the

cable tension spring (2).

2. Move the cable tension spring (2) toward

the front of the unit to achieve maximum

cable slack.

3. (Figure 11) Remove the upper end of the

auger control cable (3) from the auger

drive lever (4).

4. Install the auger control cable (3) in the

hole shown in Figure 11.

5. (Figure 12) Slide the cable tension spring

(2) toward the rear of the unit until all cable

slack is removed.

NOTE: The auger control cable (3) is

properly adjusted when the free cable

slack is removed and there is no tension

on the idler arm.

6. Tighten the nut (1) that holds the cable ten-

sion spring (2).

7. To check the adjustment, start the snow

thrower. Make sure the auger does not rotate

when the auger drive lever is released.

How To Remove The Top Cover

(Figure 10)

There are no adjustments under the top cover

(1). To clean the engine cooling system, follow

the steps below to remove the top cover (1).

1. Remove screws (2) that attach the rod sup-

port clamp the the top cover (1). Pivot the

crank assembly rod (3) up and lay on unit.

2. Remove screws (4).

3. Remove attachment screws (5).

4. Remove the top cover (1).

5. To install the top cover (1), reverse the

above steps.

How To Remove The Belt Cover

(Figure 9)

1. Remove the screws (1) and nuts (2) from

the belt cover (3).

2. Remove attachment screw (4) from the rear

of the belt cover (3).

3. Remove the belt cover (3) from the unit.

4. To install the belt cover (3), reverse the

above steps.

NOTE: The belt cover (3) has belt guides

moulded onto the inside of the belt cover (3).

When you install the belt cover (3), engage

the auger drive lever to tighten the belt

against the pulley. This will provide adequate

clearance for the belt guides when installing

the belt cover (3).

How To Replace The Auger Drive Belt

The drive belt is of special construction and

must be replaced with an original factory re-

en

14

1741416

placement belt available from your nearest au-

thorized service center.

If the auger drive belt is damaged, the snow-

thrower will not discharge snow and will not

move forward. Replace the damaged belt as

follows:

1. Disconnect the spark plug wire.

2. Remove the belt cover. See “How To Re-

move The Belt Cover”.

3. Note the path of the auger drive belt (1). For

assistance, a diagram decal is provided.

4. (Figure 14) Remove the belt guide screw

(2) and the belt guide (3). To remove the

belt guide (3), rotate the belt guide (3)

down.

5. (Figure 15) Remove the idler screw (4) and

idler pulley (5) from the idler arm (6).

6. (Figure 16) Remove the auger drive belt (1)

from the engine pulley and pull through side

of motor box.

7. (Figure 17) To remove the auger drive belt

(1) from the impeller pulley (7), move the

idler arm to the engaged position. This will

provide clearance (8) between the impeller

pulley (7) and the brake arm (9) to remove

the auger drive belt.

8. To install a new auger drive belt (1), reverse

the above steps.

9. Check the adjustment of the auger drive

cable. See “Adjust Auger Control Cable”.

How To Remove The Auger

1. Remove the belt cover. See “How To Re-

move The Belt Cover”.

2. Remove the auger drive belt. See “How To

Replace The Auger Drive Belt”.

3. (Figure 18) Remove the auger pulley (1)

from the auger shaft (threads are left hand;

turn clockwise to remove).

4. To keep the auger (6) from rotating, set a

2”x4” piece of wood on the center paddle

(3) to secure auger (6).

5. Remove bolts (4), washer (5), and nuts (2)

from front of right cover (7).

6. Remove screw (8) from back of right cover

(7).

7. Remove bolts (9) and nuts (10).

8. (Figure 19) Slide the auger (6) out of the

right side of the auger housing (11).

9. Slide the auger (6) out of the bearing on the

left side of the auger housing (11).

10.To install auger (6), reverse the above steps.

Lubrication

How To Check The Engine Oil (Figure 3)

Check the oil level before starting the engine

and after each eight (8) hours of continuous use.

1. Make sure the unit is level.

2. Remove the oil fill cap/dipstick (1) and fill

the crankcase to “FULL” line on dipstick. DO

NOT overfill.

3. Tighten the oil fill cap/dipstick (1) securely

each time you check the oil level.

NOTE: Synthetic oil can assist with starting

in extreme cold temperatures. Synthetic

5W30 is acceptable for all temperatures. DO

NOT mix oil with petrol.

How To Change The Engine Oil

Change the engine oil every fifty (50) hours or at

least once a year if the snow thrower is not used

for fifty (50) hours.

To change the engine oil, the engine must be

tilted forward and the oil drained from the oil fill

tube. Change oil when the engine is warm.

1. (Figure 5) Lift the rear of the snowthrower

and tilt the unit forward. In the correct posi-

tion, the snowthrower will be setting on the

front of the auger housing.

2. Put an oil drain pan (1) under the oil fill

tube (2).

3. Carefully remove the oil fill cap/dipstick. Oil

will begin to flow into the oil drain pan (2).

4. After all the oil has drained from the engine,

set the snowthrower in the upright operating

position.

5. (Figure 3) Fill the engine with S.A.E. 5W30

oil. Make sure the oil reaches the FULL mark

on the oil fill cap/dipstick. DO NOT OVER-

FILL.

NOTE: Synthetic oil can assist with starting

in extreme cold temperatures. Synthetic

5W30 is acceptable for all temperatures. DO

NOT mix oil with petrol.

How To Replace The Spark Plug

(Figure 20)

NOTE: This spark ignition system meets all

requirements of the Canadian Interference--

Causing Equipment Regulations.

NOTE: This engine complies with all current

Australian and New Zealand limitations elec-

tromagnetic interference.

Check the spark plug (1) every twenty-five (25)

hours. Replace the spark plug (1) if the elec-

trodes are pitted or burned, if the porcelain is

cracked, or every 100 hours of use.

1. Make sure the spark plug (1) is clean. Clean

the spark plug (1) by carefully scraping the

electrodes (do not sand blast or use a wire

brush).

2. Check the spark plug (1) gap with a feeler

gauge (2) and reset gap to 0.030” if neces-

sary..

3. Before installing the spark plug (1), coat the

threads lightly with oil for easy removal.

Tighten the spark plug (1) to a torque of 15

foot-pounds.

How To Prepare The Snow Thrower For

Storage

WARNING: Do not remove petrol

while inside a building, near a fire,

or while you smoke. Petrol fumes

can cause an explosion or a fire.

If the snow thrower is to be stored for an ex-

tended period, refer to the engine manufactur-

er’s operating manual (included with some

models) for important maintenance or storage

details.

1. Drain the fuel tank.

2. Let the engine run until it is out of gasoline.

3. Never store the snow thrower with fuel in the

tank inside a building where ignition sources

are present such as hot water and space

heaters, clothes dryers, and the like. Allow

the engine (motor) to cool before storing in

any enclosure.

4. Drain the oil from the warm engine. Fill the

engine crankcase with new oil.

5. Remove the spark plug from the cylinder.

Pour one ounce of oil into the cylinder. Slow-

ly pull the recoil--start grip so that the oil will

protect the cylinder. Install a new spark plug

in the cylinder.

6. Thoroughly clean the snow thrower.

7. Lubricate all lubrication points. See the Main-

tenance section.

8. Be sure that all nuts, bolts and screws are

securely fastened. Inspect all visible moving

parts for damage, breakage and wear. Re-

place if necessary.

9. Cover the bare metal parts of the blower

housing and auger with spray rust preventa-

tive lubricant.

10.Put the unit in a building that has good ven-

tilation.

11. If the machine must be stored outdoors,

block up the snow thrower to be sure the en-

tire machine is off the ground.

12.Cover the snow thrower with a suitable pro-

tective cover that does not retain moisture.

Do not use plastic.

How To Order Replacement Parts

The replacement parts are shown either on the

back pages of this Instruction Book or in a

separate Parts List Book.

Use only manufacturer’s authorized or approved

replacement parts. The letter placed on the end

of the part number denotes the type of finish for

the part, C for chrome, Z for zinc, a PA for

purchased assembly. It is important that you

include this when ordering a part. Do not use

attachments or accessories not specifically

recommended for this unit. In order to obtain

proper replacement parts you must supply the

model number (see nameplate).

Warranty service is available only through Autho-

rized Service Dealers. Locate your nearest dealer

in our locator map at www.murray.com.

Replacement parts for the engine, transaxle, or

transmission, are available from the

manufacturer’s authorized service center found

in the yellow pages of the telephone directory.

Also, see the individual engine or transmission

warranties to order replacement parts.

When ordering the following information is

required:

(1) The Model Number

(2) Serial Number

(3) Part Number

(4) Quantity

en

15

1741416

TROUBLE SHOOTING CHART

TROUBLE CAUSE CORRECTION

Difficult starting Defective spark plug. Replace spark plug.

Water or dirt in fuel system. Use carburetor bowl drain to flush and refill with

fresh fuel.

Engine runs erratic Blocked fuel line, empty gas tank, or stale

gasoline Clean fuel line; check fuel supply; add fresh

gasoline

Engine stalls Unit running on CHOKE. Set choke lever to RUN position.

Engine runs erratic;

Loss of power Water or dirt in fuel system. Use carburetor bowl drain to flush and refill with

fresh fuel.

Excessive vibration Loose parts: damaged impeller Stop engine immediately and disconnect spark

plug wire. Tighten all bolts and make all

necessary repairs. If vibration continues, have

the unit serviced by a competent repairman.

Unit fails to propel itself Drive belt loose or damaged. Replace drive belt.

Unit fails to discharge snow Auger drive belt loose or damaged. Adjust auger drive belt; replace if damaged.

Auger control cable not adjusted correctly. Adjust auger control cable.

Discharge chute clogged. Stop engine immediately and disconnect spark

plug wire. Clean discharge chute and inside of

auger housing.

Foreign object lodged in auger Stop engine immediately and disconnect spark

plug wire. Remove object from auger.

en

16

1741416

BRIGGS & STRATTON CORPORATION OWNER WARRANTY POLICY

Effective January 1, 2006 replaces all undated Warranties and all Warranties dated before January 1, 2006

Briggs & Stratton Corporation will repair or replace, free of charge, any part(s) of the product that is defective in material or workmanship or both.

Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser. This warranty is effective

for the time periods and subject to the conditions stated below. For warranty service, find the nearest Authorized Service Dealer in your area. For

warranty service, find the nearest Authorized Service Dealer in our dealer locator map at www.murray.com.

THERE IS NO OTHER EXPRESS WARRANTY. IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR FROM PURCHASE, OR TO THE EXTENT PERMITTED BY LAW ANY AND ALL

IMPLIED WARRANTIES ARE EXCLUDED. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES ARE EXCLUDED TO THE

EXTENT EXCLUSION IS PERMITTED BY LAW. Some states or countries do not allow limitations on how long an implied warranty lasts, and

some states or countries do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation and exclusion

may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state or country to

country.

LIMITED WARRANTY

WARRANTY TERMS

Consumer Commercial Condition of

Brand / Unit Use Use Warranty Term

Single Stage Snowthrower 1 year 90 days......... .............

Dual Stage Snowthrower 2 year 90 days.......... .............

The warranty period begins on the date of purchase by the first retail consumer or commercial end user, and continues for the period of

time stated in the table above. “Consumer use” means personal residential household use by a retail consumer. “Commercial use” means

all other uses, including use for commercial, income producing or rental purposes. Once product has experienced commercial use, it shall

thereafter be considered as commercial use for purposes of this warranty.

No warranty registration is necessary to obtain warranty on Murray branded products. Save your proof of purchase receipt. If you do not

provide proof of the initial purchase date at the time warranty service is requested, the manufacturing date of the product will be used to

determine the warranty.

ABOUT YOUR WARRANTY

We welcome warranty repair and apologize to you for being inconvenienced. Any Authorized Service Dealer may perform warranty

repairs. Most warranty repairs are handled routinely, but sometimes requests for warranty service may not be appropriate. For example,

warranty service would not apply to the product if damage occurred because of misuse, lack of routine maintenance, shipping, handling,

warehousing or improper installation. Similarly, the warranty is void if the serial number on the product has been removed or the product

has been altered or modified.

This warranty covers product related defective material and/or workmanship only. To avoid misunderstanding which might occur be-

tween the customer and the Dealer, listed below are some of the causes of product failure that the warranty does not cover.

xNormal Wear: Small Engine Powered Equipment, like all mechanical devices, needs periodic parts and service to perform well. Warranty does not

cover repair when normal use has exhausted the life of the product or part.

xInstallation: This warranty does not apply to product that has been subjected to improper or unauthorized installation, alteration or modification. Nor

installations that prevent starting, cause unsatisfactory engine performance.

xImproper Maintenance: The life of this product depends upon the conditions under which it operates, and the care it receives. Recommended

maintenance and adjustment intervals are stated in the Operator’s Manual. Often product, such as tillers, edgers, rotary mowers, are used in dusty

or dirty conditions, which can cause what appears to be premature wear. Such wear, when caused by dirt, dust, or other abrasive material entering

the product because of improper maintenance is not covered by warranty. The warranty will not cover repairs due to problems caused by replace-

ment parts that are not original manufactured part(s).

xIncorrect and/or insufficient fuel or lubrication: This warranty does not cover damage caused by the use of stale fuel, or altered gasolines. Dam-

age to engine or engine components ie, combustion chamber, valves, valve seats, valve guides, burned starter motor windings caused by use of

alternate fuels such as liquified petroleum, natural gas, are not covered unless engine is certified for this operation. Parts which are scored or bro-

ken because product was operated with insufficient, contaminated or incorrect grade of lubricating oil as well as product components damaged due

to lack of lubrication are not covered.

xOperational Misuse: Proper operation of the product is stated in the Operator’s Manual. Product damaged by overspeeding, overheating, or opera-

tion in a confined area without sufficient ventilation. Product broken by excessive vibration caused by a loose engine mounting, loose or unbalanced

blades, impellers, overspeeding, or bent crankshaft due to striking of solid object. Damage or malfunctions resulting from accidents, abuse, or im-

proper servicing or freezing or chemical deterioration, as well as operating in excess of recommended capacities as outlined in the Operator’s

Manual are not covered.

xRoutine tune-up, wear items or adjustments: This warranty excludes wear items such as oil, belts, blades, o-rings, filters, etc.

xOther exclusions: Repair or adjustments for part(s) that are not manufactured by Briggs & Stratton Corporation, are not covered, see warranty for

respective manufacturers. This warranty excludes failures due to acts of God and other force majeure events beyond the manufacturers con-

trol. Also excluded are used, reconditioned, and demonstration products.

Warranty service is available only through Authorized Service Dealers. Locate your nearest dealer in our locator map at www.murray.com.

fr

17

1741416

TABLE DES MATIÈRES

SYMBOLES DE DANGERS ET SIGNIFICATIONS 18....

SYMBOLES DE DANGERS ET LEURS SIGNIFICATIONS 18

CONSEILS DE SECURITE 19.........................

ASSEMBLAGE 21...................................

FONCTIONNEMENT 21..............................

ENTRETIEN 24......................................

TABLEAU D’ENTRETIEN 24..........................

TABLEAU DE DÉPANNAGE 26.......................

GARANTIE LIMITÉE 27..............................

Informations générales

Ce manuel d’instruction est écrit pour une personne qui possède

quelques compétences mécaniques. Comme dans la plupart des

manuels d’entretien, toutes les étapes ne sont pas décrites. Les étapes

qui concernent le dévissage où le serrage des attaches sont des étapes

que n’importe qui peut suivre avec un minimum de connaissances

mécaniques. Lisez et suivez ces instructions avant d’utiliser votre

équipement.

Connaissez votre produit : Si vous comprenez votre équipement et

comment il fonctionne, vous obtiendrez les meilleures performances

possibles. Pendant que vous lisez ce manuel, comparez les illustrations

et l’équipement. Apprenez l’emplacement et les fonctions des

commandes. Pour aider à prévenir les accidents, suivez les instructions

de fonctionnement et les règles de sécurité. Conserver ce manuel pour

référence future.

IMPORTANT : De nombreuses unités ne sont pas assemblées et sont

vendues dans des cartons. Il est de la responsabilité du propriétaire de

s’assurer que les instructions d’assemblage contenues dans ce manuel

sont suivies à la lettre. D’autres unités sont achetées entièrement

assemblées. Sur les unités déjà assemblées, il est de la responsabilité

du propriétaire de s’assurer que l’unité est correctement assemblée. Le

propriétaire doit vérifier l’unité avec attention en accord avec les

instructions trouvées dans ce manuel avant la première utilisation.

Commandes et caractéristiques de l’équipement

(voir Figure 1)

Manivelle (2) – Change la direction de la goulotte d’éjection.

Goulotte d’éjection (3) – Change la distance d’éjection de la neige.

Goulotte d’éjection (4) – Change la direction d’éjection de la neige.

Levier de fraise (5) – Démarre et arrête la fraise (ramassage et

éjection de la neige) qui propulse également la déneigeuse.

Caractéristiques du moteur

Commutateur d’arrêt (8) - Doit être placé sur la position MARCHE

(ON) pour démarrer le moteur.

Bouton d’amorçage (9) - injecte de l’essence directement dans le

carburateur pour un démarrage rapide par temps froid.

Poignée de démarreur à rappel (12) – Utilisé pour un démarrage

manuel du moteur.

Commande du starter (14) – Utilisé pour un démarrage à froid du

moteur.

fr

18

1741416

Ce manuel contient des informations de sécurité

destinées à vous faire prendre conscience des

dangers et des risques associés avec les souffleuses à neige, et à

comment les éviter. La souffleuse à neige est conçue pour être

utilisée pour le déblayage de la neige, et ne doit pas être utilisée à

d’autres fins. Il est important que vous lisiez et que vous compreniez

ces instructions, et que toute personne qui doit faire fonctionner

l’équipement lise et comprenne ces instructions.

Les gaz échappement du moteur de cette machine contiennent des

produits chimiques identifiés par l’état de Californie comme entraînant le

cancer, des malformations de naissance, et autres préjudices

reproductifs.

AVERTISSEMENT

Un mot de signalisation (DANGER, AVERTISSEMENT, ou PRUDENCE)

est utilisé avec le symbole d’alerte pour indiquer la possibilité de

blessures et leurs degrés de sévérité. En complément, un symbole de

danger peut être utilisé pour représenter le type de danger.

DANGER indique un risque qui, s’il n’est pas évité, entraînera

la mort ou de sérieuses blessures.

AVERTISSEMENT indique un risque qui, s’il n’est pas évité,

pourrait entraîner la mort ou de sérieuses blessures.

PRUDENCE indique un risque qui, s’il n’est pas évité, pourrait

entraîner des blessures mineures ou modérées.

PRUDENCE lorsque utilisé sans le symbole d’alerte, indique

une situation qui pourrait endommager l’équipement.

Symboles de dangers et significations

Ces symboles sont utilisés sur votre équipement et sont définis dans

votre manuel de fonctionnement. Revoyez et comprenez ce qu’ils

veulent dire. L’utilisation de l’un de ces symboles en combinaison avec

un mot d’avertissement vous avertira d’un danger potentiel et de

comment l’éviter.

Incendie

Manuel de l’utilisateur – Lire et comprendre avant

d’entreprendre toute activité ou de faire fonctionner

l’équipement.

Alerte de sécurité – Identifie les informations de sécurité

à propos d’un danger qui peut entraîner des blessures.

Turbine rotative Explosion

Choc

Surfaces brûlantes

Fraise rotative

Fumées toxiques

Engrenages en

rotation

Projection d’objets

Maintenir une distance

de sécurité entre vous

et l’équipement.

Ne jamais mettre les

mains dans les pièces

en rotation.

Usage d’un

protège-oreilles

recommandé pour un

usage prolongé.

Arrêter le moteur et retirer le connecteur de la bougie

avant d’effectuer tout travail de maintenance ou de

réparation.

Symboles de dangers et leurs significations

Ces symboles sont utilisés sur votre équipement et sont définis dans

votre manuel de fonctionnement. Il est important que vous revoyiez et

que vous compreniez la signification de ces symboles. Un manquement

de compréhension des symboles peut entraîner des risques de

blessures corporelles.

Arrêt

Carburant

Starter à l’arrêt

Huile

Starter en marche

Lent

Rapide

Marche Arrêt

Clédecontact

Contact désactivé

Contact activé

Pompe

d’amorçage

Manette des gaz

Embrayage

de traction

Embrayage

de la fraise

Engager

Collecteur de la

fraise

Traction

Marche avant

Point mort

Marche arrière

Appuyer pour

engager le

démarreur électrique

Démarreur

électrique

Démarrage du

moteur

Moteur en marche

Moteur à l’arrêt

Engager

Disengager

Déversoir Déflecteur

DROITEGAUCHE HAUT BAS

Poignées chauffées

Engager

fr

19

1741416

ATTENTION: Cette machine est capable aux objets d’amputation de mains et de pieds et de lancement..

Lire les règles de sécuritéet les respecter scrupuleusement. Le non respect de ces règles peut entraîner

une perte de contrôle de la machine,des blessures voire de décès pour l’utilisateur ou les personnes pré-

sentes, ainsi que des dommages matériels. Le tri--angle , dans le manuel, signale des mises en garde

et avertissements importants qui doivent être respectés.

Régles de sécurité a suivre pour l’utilization des chasse-neige

IMPORTANT : les normes de sécurité requièrent des contrôles de la pré-

sence du conducteur pour limiter les risques de blessures. Votre chasse--

neige est équipé de ces contrôles. Ne pas tenter de rendre la fonction de

contrôle de la présence du conducteur inopérante quelles que soient les

circonstances.

Formation

1. Lire, comprendre et respecter toutes les instructions fig--urant sur la

machine et dans les manuels avant de fairefonctionner cet appareil.

Veiller à bien se familiariseravec les commandes et la bonne utilisation

du matériel.Il importe de savoir comment arrêter la machine etdébrayer

les commandes rapidement.

2. Ne jamais laisser d’enfants faire fonctionner le matériel.Ne jamais

laisser d’adultes faire fonctionner le matérielsans initiation appropriée.

3. Maintenir toutes les personnes, en particulier les jeunesenfants et les

animaux domestiques, à l’écart de la zoned’utilisation.

4. Faire preuve de précaution pour éviter de glisser ou dechuter, notam-

ment en marche arrière.

Préparation

1. Contrôler avec soin la zone où doit être utilisé lematériel et enlever tous

paillassons, luges, planches, filset autres objets étrangers.

2. Débrayer toutes les transmissions et passer au pointmort avant de

démarrer le moteur.

3. Ne pas utiliser ce matériel sans porter une tenue d’hiverappropriée.

Porter des chaussures offrant une bonneprise sur les surfaces glis-

santes. Évitez l’habillementconvenable lâche qui peut se faire attraper

dans lespièces mobiles.

4. L’essence est très est inflammable ; la manipuler avecprécaution.

a. Utiliser un bidon d’essence homologué.

b. Ne jamais verser d’essence dans un moteur enmarche ou chaud.

c. Remplir le réservoir d’essence en plein air avecextrêmement de

précaution. Ne jamais remplir le réser--voir à l’intérieur. Remettre le

capuchon d’essence enplace et essuyer toute éclaboussure d’ess-

ence.

d. Ne jamais remplir de bidons à l’intérieur d’unvéhicule ou sur le pla-

teau à habillage en plastique d’unecamionnette ou d’une remorque.

Toujours poser lesbidons sur le sol à l’écart du véhicule avant de les

rem--plir.

e. Autant que possible, descendre une machine àessence de la ca-

mionnette ou de la remorque et refairele plein à terre. Si ce n’est

pas possible, laisser lamachine sur la remorque et faire le plein à

l’aide d’unbidon d’essence, plutôt qu’avec le pistolet de la pompe

àessence.

f. Garder en permanence l’embout du pistolet contre lebord de l’orifice

du réservoir ou du bidon d’essence,jusqu’à ce que celui--ci soit

plein. Ne pas utiliser leloquet de blocage du pistolet en position

ouverte.

g. Remettre le capuchon d’essence en place et essuyertoute écla-

boussure d’essence.

h. En cas d’éclaboussement d’essence sur les vête--ments, se chang-

er immédiatement.

5. Utiliser des rallonges et des prises conformes aux indi--cations du

fabricant pour tous les appareils à moteur ouà démarreur électrique.

6. Régler la hauteur du boîtier de collecteur en fonctiondes surfaces en

gravier ou en pierres concassées.

7. Ne jamais tenter d’effectuer des réglages alors que lemoteur est en

marche (sauf indication contraire spéci--fique du fabricant).

8. Laisser le moteur refroidir et la machine s’adapter auxtempératures

extérieures avant de commencer àdégager la neige.

9. Toujours porter des lunettes de sécurité ou une protec--tion oculaire

durant l’utilisation ou lors de réglages ou deréparations, afin de pro-

téger les yeux des objets pou--vant être projetés par la machine.

Fonctionnement

1. Ne pas placer les mains ou les pieds à proximité ou sous des pièces

en rotation. Toujours se tenir à l’écart de la bouche d’éjection.

2. Faire preuve de la plus grande prudence lors de l’utilisation ou de

passages sur des allées, chemins ou chaussées en gravier. Prendre

garde à la circulation et aux dangers cachés.

3. En cas de heurt d’un objet étranger, arrêter le moteur (à essence) et

débrancher le câble de la bougie ou débrancher le cordon (modèle

électrique), contrôler avec soin l’état de la déneigeuse et réparer tout

dommage avant de redémarrer et d’utiliser la machine.

4. Si la machine commence à vibrer de façon anormale, arrêter le moteur

et rechercher immédiatement la cause. Les vibrations indiquent géné-

ralement un problème.

5. Arrêter le moteur pour quitter la zone de travail, avant de désobstruer le

carter de collecteur/turbine ou le guide de décharge et lors de toute

opération de réparation, de réglage ou de contrôle.

6. Lors du nettoyage, de réparations ou de contrôles, s’assurer d’abord de

l’arrêt complet de collecteur/de la turbine et de toutes les pièces en

mouvement. Pour écarter les risques de démarrage accidentel, dé-

brancher le câble de la bougie et le maintenir à l’écart de la bougie.

7. Lors du nettoyage, de réparations ou de contrôles, s’assurer d’abord de

l’arrêt complet de collecteur/de la turbine et de toutes les pièces en

mouvement. Pour écarter les risques de démarrage accidentel, dé-

brancher le câble de la bougie et le maintenir à l’écart de la bougie.

8. Faire preuve de la plus grande prudence sur les terrains en pente. Ne

pas tenter de déneiger les pentes fortes.

9. Ne jamais utiliser la déneigeuse si tous les carters, capots et autres

dispositifs de protection ne sont pas en place et en état de fonctionner.

10. Ne jamais diriger l’éjection vers des personnes ou de façon à causer

des dommages matériels. Tenir les enfants et autres personnes à

l’écart.

11. Ne pas surcharger la machine en tentant de déneiger à un débit trop

élevé.

12. Ne jamais utiliser la machine à des vitesses de déplacement élevées

sur des surfaces glissantes. En marche arrière, regarder derrière soit

et faire preuve de prudence.

13. Débrayer l’entraînement du collecteur/de la turbine avant de transporter

la déneigeuse ou quand elle n’est pas utilisée.

14. Utiliser exclusivement des pièces et accessoires homologués par le

fabricant de la déneigeuse (poids pour roues, contrepoids ou cabines).

15. Ne jamais utiliser la déneigeuse lorsque la visibilité ou la lumière sont

insuffisantes. Toujours avoir le pied sûr et tenir fermement le guidon.

Marcher, ne jamais courir.

16. Ne jamais toucher un moteur ou pot d’échappement chaud.

17. Ne jamais utiliser la déneigeuse à proximité de surfaces vitrées, voi-

tures, soupiraux, dévers et autres sans ajustement correct de l’angle

d’éjection.

fr

20

1741416

18. Ne jamais diriger l’éjection vers les personnes présentes ni laisser

quiconque se tenir devant la machine.

19. Ne jamais laisser la machine en marche sans surveillance. Toujours

débrayer les commandes de fraise et d’avance, arrêter le moteur et

sortir les clés.

20. Ne pas utiliser la machine sous l’emprise de l’alcool ou d’un stupé-

fiant.

21. Ne pas oublier que l’utilisateur est considéré responsable des dom-

mages matériels et des accidents subis par des tiers.

22. L’expérience montre que les utilisateurs de 60 ans ou plus sont impli-

qués dans une proportion importante des accidents corporels liés au

matériel. Ces utilisateurs devront évaluer leur capacité à utiliser la

machine sans s’exposer eux--mêmes ou d’autres à des risques de

blessure.

23. NE PAS porter de longue écharpe ni de vêtements amples suscepti-

bles d’être pris dans des pièces en mouvement.

24. La neige peut cacher des obstacles. Veiller à enlever tous les ob-

stacles de la zone à déneiger.

Enfants

Des accidents tragiques peuvent se produire lorsque l’utilisateur n’est pas

conscient de la présence d’enfants. Les enfants sont souvent attirés par la

machine et par son fonctionnement. Ne jamais présumer que les enfants

resteront toujours au même endroit.

1. Garder les enfants à l’écart et sous la surveillance d’un autre adulte

responsable.

2. Faire preuve de vigilance et couper le moteur si des enfants s’approch-

ent de la machine.

3. Ne jamais laisser d’enfant conduire la machine.

4. Faire preuve de prudence particulière à l’approche de coins sans

visibilité, buissons, arbres et autres objets susceptibles de bloquer la

vue.

Dégager une manche d’éjection obstruée

Le contact de la main avec la turbine en rotation à l’intérieur de la manche

d’éjection est la cause la plus courante de blessures associées aux dé-

neigeuses. Ne jamais se servir des mains pour nettoyer la manche

d’éjection.

Pour dégager la manche:

1. ARRÊTER LE MOTEUR.

2. Attendre 10 secondes pour s’assurer que les pales de la turbine ont

cessé de tourner.

3. Toujours utiliser un outil de nettoyage, par les mains.

Réparation, entretien et entreposage

1. Vérifier le serrage des boulons de cisaillement et autres boulons à

intervalles fréquents pour s’assurer que le matériel fonctionne sans

danger.

2. Ne jamais entreposer la machine avec de l’essence dans le réservoir à

l’intérieur d’un bâtiment en présence de sources d’inflammation, notam-

ment chauffe--eau, radiateurs ou sèche--linge. Laisser le moteur refroi-

dir avant de l’entreposer dans un quelconque espace fermé.

3. Toujours consulter les détails importants figurant dans le mode d’emploi

si la déneigeuse doit être entreposée durant une période prolongée.

4. Nettoyer ou changer au besoin les étiquettes d’instructions et de sécu-

rité.

5. Laisser tourner la machine pendant quelques minutes après avoir dé-

neigé pour empêcher le grippage du collecteur/de la turbine.

6. En cas de déversement accidentel d’essence, ne pas démarrer le

moteur, mais amener la machine à l’écart de la zone de déversement

et éviter de produire une quelconque source d’inflammation avant la

dissipation totale des vapeurs de carburant.

7. Toujours respecter les règles de sécurité concernant l’essence lors

du remplissage du réservoir suite au transport ou à l’entreposage de

la machine.

8. Toujours respecter les instructions de préparation à l’entreposage figur-

ant dans le manuel du moteur avant de remiser la machine, à court

comme à long terme.

9. Toujours suivre les instructions de redémarrage figurant dans le manuel

du moteur lors de la remise en service de la machine.

10. Nettoyer ou changer au besoin les étiquettes d’instructions et de sécu-

rité.

11. Vérifier le serrage des vis et des écrous et maintenir la matériel en bon

état.

12. Ne jamais modifier des dispositifs de protection. Vérifier régulièrement

leur bon fonctionnement et effectuer le cas échéant les réparations

nécessaires.

13. Les organes de la machine sont sujets à usure, dommages et dété-

rioration. Contrôler fréquemment les différents éléments et changer au

besoin les pièces conseillées par le fabricant.

14. Vérifier régulièrement le bon fonctionnement des commandes. Régler

et réparer selon les besoins.

15. En cas de réparation, utiliser exclusivement des pièces homologuées

par le fabricant.

16. Effectuer tous les réglages et ajustement conformément aux spécifica-

tions du fabricant.

17. Pour les opérations d’entretien et de réparation importantes, utiliser

exclusivement les services d’un centre de réparation autorisé.

18. Ne jamais tenter de réparation importante sur la machine à moins d’y

avoir été correctement formé. Toute opération d’entretien incorrecte

peut entraîner des dangers de fonctionnement, des dommages maté-

riels et l’annulation de la garantie du fabricant.

19. Vérifier le serrage des boulons de cisaillement et autres boulons à

intervalles fréquents pour s’assurer que le matériel fonctionne sans

danger.

Émissions

1. Les gaz d’échappement de cette machine contiennent des substances

qui, en certaines quantités, sont responsables de cancers, malforma-

tions congénitales et autres troubles de la reproduction.

2. Le cas échéant, se reporter aux indications de durée de persistance

des émissions et d’indice de l’air sur l’étiquette d’émission du moteur.

Systéme d’allumage par étincelle

1. Ce systéme d’allumage par étincelle est conforme à la norme NMB-002

du Canada.

Stránka sa načítava ...

Simplicity SINGLE STAGE SNOWTHROWER Používateľská príručka

Simplicity SINGLE STAGE SNOWTHROWER Používateľská príručka

V iných jazykoch