Stránka sa načítava...
1
2
4
12
11
10
13
16
17
14
9
8
5
18
6 7
3
15
1
GC9600 range
EN User Manual
© 2021 Philips Domestic Appliances Holding B.V.
All rights reserved
4239.001.1873.4 (16/12/2021)
A
B
C
78 9
11
3 54
12 13
18
6
2x
10
2
2 sec.
14 16 17
19
23
15
20 21
22
EN IMPORTANT: Perform descaling regularly for great steam and
prolonged life.
Let the appliance cool down completely, before you remove the
EASY DE-CALC KNOB.
CS
RO
RU
TR
D
GC9600 range
ENGLISH 6
HRVATSKI 37
SLOVENSKY 73
6
Introduction
.
appliance. Save both documents for future reference.
1 Steam supply hose
2 Iron platform
3 First supply hose storage compartment
4 Mains cord with plug
5 ECO button with light
8 EASY DE-CALC light
10 Cord storage compartment
11 Second supply hose storage compartment
15 Soleplate
16 Steam trigger
17 ‘Iron ready’ light
18 Filling hole
This appliance has been designed to be used with tap water. However, if you live in an area with hard
water, fast scale build-up may occur.
appliance.
2
3
the steam trigger to let the appliance heat up again. When the ‘iron ready’ light lights up continuously,
you can continue steam ironing.
7
The Optimal TEMP Technology enables you to iron all types of ironable fabrics, in any order, without
platform. This will help reduce the stress on your wrist.
-
rayon (Fig. 5).
-
garments (Fig. 6).
Ironing
2
3
,
4
5
- Double press the steam trigger for a continuous shot of steam (Fig. 10). It is not necessary to press and
hold the steam trigger continuously when the steam boost function is activated. To stop the steam
boost function, press the steam trigger once.
- By using the ECO mode (reduced amount of steam), you can save energy without compromising on
the ironing result. The green light is on (Fig. 12).
-
-
-
For faster ironing and a higher amount of steam, you can use Turbo steam.
2
To properly maintain your appliance, clean the iron and the appliance regularly.
2
Tip: Clean the soleplate regularly to ensure smooth gliding.
sessions to indicate that the appliance needs to be descaled. Perform the following descaling procedure
before you continue ironing.
2
3
4
5
9
2
3
4
5
6
7
8
9
Storage
2
3
4
5
This chapter summarises the most common problems you could encounter with the appliance.
If you are unable to solve the problem with the information below, visit for a
The ironing board
cover becomes wet
or there are water
droplets on the
garment during
ironing.
Steam has condensed on the
ironing board cover after a
long ironing session.
Replace the ironing board cover if the foam
material has worn out. You can also add an
board cover to prevent condensation on the
ironing board. You can buy felt in a fabric
shop.
You have an ironing board
cover that is not designed to
cope with the high steam rate
of the appliance.
ironing board cover to prevent condensation
on the ironing board. You can buy felt in a
fabric shop.
Water droplets come
out of the soleplate.
The steam that was still
present in the hose has cooled
down and condensed into
water. This causes water
droplets to come out of the
soleplate.
Steam away from the garment for a few
seconds.
Steam and/or water
come out from under
the EASY DE-CALC
tightened properly.
appliance properly. Note: Some water may
The rubber sealing ring of the
Contact an authorised Philips service centre
Dirty water and
impurities come out
of the soleplate or
the soleplate is dirty.
Impurities or chemicals
present in the water have
deposited in the steam vents
and/or on the soleplate.
Clean the soleplate with a damp cloth.
Too much scale and minerals
have accumulated inside the
appliance.
Descale the appliance regularly (see chapter
‘Important - DESCALING’).
The iron leaves a
shine or an imprint
on the garment.
The surface to be ironed was
uneven, for instance because
you were ironing over a seam
or a fold in the garment.
PerfectCare is safe on all garments. The shine
if you wash the garment. Avoid ironing over
seams or folds or you can place a cotton cloth
over the area to be ironed to avoid imprints at
seams and folds.
The appliance does
not produce any
steam.
There is not enough water in
The appliance is not hot
enough to produce steam.
Wait until the ‘iron ready’ light on the iron
lights up continuously.
You did not press the steam
trigger.
while you iron.
the appliance properly.
The appliance is not switched
on.
The appliance has
activated automatically when
the appliance has not been
used for more than 10
minutes.
the appliance again.
The appliance
produces a pumping
sound.
Water is pumped into the
boiler inside the appliance.
This is normal.
If the pumping sound continues nonstop,
Philips service centre.
.
2
3
-
-
2
3
,
4
5
-
-
-
-
-
2
2
2
3
4
5
2
3
4
5
6
7
8
9
2
3
4
5
Úvod
.
vodu.
2
3
-
-
2
3
,
4
5
-
R
-
-
-
-
2
2
2
3
4
5
2
3
4
5
6
7
8
9
2
3
4
5
vody.
pára anebo voda.
stopy.
/