Silvercrest KH 2130 Operating Instructions Manual

RADIO SET

KOMPERNASS GMBH

BURGSTRASSE 21 ⋅ D-44867 BOCHUM

www.kompernass.com

ID-Nr.: KH 2130-06/09-V3

4BC

KH 2130

Radio Set

Operating instructions

Komplet za prenos signala

Navodila za uporabo

Sada na přenos audio a video signálu

Návod k obsluze

Súprava rádioprenosových zariadení

Návod na obsluhu

CV_KH2130_DT35269_LB4BC.indd 1CV_KH2130_DT35269_LB4BC.indd 1 01.09.2009 10:02:50 Uhr01.09.2009 10:02:50 Uhr

Hersteller / Verantwortliche Person

Manufacturer / responsible person

Kompernaß GmbH

Burgstraße 21

44867 Bochum

erklärt, dass das Produkt

declares that the product

Funkübertragungs-Set

Radio Transmission Set

Type (ggf. Anlagenkonfiguration mit Angabe der Module):

Type (if applicable, configuration including the modules)

KH 2130

 Telekommunikations(Tk-)endeinrichtung

Telecommunicätions ternlinal equiprrient

5 Funkanlage

Radio equipment

Verwendungszweck / lntended purpose

Übertragung von Audio und Video Signalen

Transmission of audio and video signals

bei bestimmungsgemäßer Verwendung den grundlegenden Anforderungen des § 3 und den übrigen

einschlägigen Bestimmungen des FTEG (Artikel 3 der R&TTE) entspricht.

complies with the essential requirements of §3 and the other relevant provisions of the FTEG

(Article 3 of the R&TTE Directive), when used for its intended purpose.

Gesundheit und Sicherheit gemäß § 3 (1) 1. (Artikel 3 (1) a))

Health and safety requirements pursuant to § 3 (1) 1. (Article 3 (1) a))

angewendete harmonisierte Normen

Harmonised Standards applied

EN 60065: 2002 + A1: 2006

Schutzanforderungen in Bezug auf die elektromagnetische Verträglichkeit

(§ 3 (1) 2, Artikel 3 (1) b)

Protection requirements concerning electromagnetic compatibility § 3(1)(2), (Article 3(1) b))

angewendete harmonisierte Normen

Harmonised Standards applied

EN 301 489-1 V1.6.1

EN 301 489-3 V1.4.1

Maßnahmen zur effizienten Nutzung des Funkfrequenzspektrums

Measures for the efficient use of the radio frequency spectrum

5 Luftschnittstelle bei Funkanlagen gemäß § 3(2) (Artikel 3(2)

Air interface of the radio systems pursuant to § 3(2) (Article 3(2)

Angewendete harmonisierte Normen

Harmonised standards applied

EN 300 220-3 V1.1.1

EN 300 440-2 V1.1.2

Bochum, 29.07.2009

Hans Kompernaß

Geschäftsführer

Konformitätserklärung gemäß dem Gesetz über Funkanlagen und

Telekommunikationsendeinrichtungen (FTEG) und der Richtlinie 1999/5/EG (R&TTE)

Declaration of Conformity in accordarice with the Radio and Telecommunications Terminal Equipment Act

(FTEG) and Directive 1999/5/EC (R&TTE Directive)

KH 2130

CV_KH2130_DT35269_LB4BC.indd 2CV_KH2130_DT35269_LB4BC.indd 2 01.09.2009 10:02:50 Uhr01.09.2009 10:02:50 Uhr

- 1 -

Read these operating instructions carefully before using the device for the first time

and preserve this booklet for later reference. Pass this booklet on to whoever might

acquire the device at a future date.

CONTENT PAGE

Intended Use 2

Contents 2

Technical data 3

Safety instructions 3

The device components 6

Putting the device into use 6

Connecting the transmitter 6

Connecting the receiver 8

Switching on 8

Improving the transmission quality 9

Channel configuration (parallel operation) 9

Expansion options 9

Cleaning 9

Troubleshooting 9

Disposal 10

Importer 10

Important warranty information 11

IB_KH2130_DT35269_LB4BC.indb 1IB_KH2130_DT35269_LB4BC.indb 1 04.09.2009 13:10:06 Uhr04.09.2009 13:10:06 Uhr

- 2 -

Intended Use

The device inintended exclusively for

private, non-commercial use. The radio

transmission set is suitable for audio and

video equipment, such as:

Televisions•

SAT receiver/set top boxes•

DVD/CD players•

PCs•

etc.•

The equipment must have the appropriate

AV inputs/outputs. The radio transmission

set is intended for:

Wireless transmission of audio, video •

and infrared signals:

(Transmission distances outdoors are

possible up to approx. 100 metres!).

No warranty is provided for damages

resulting from improper use of the device!

Contents

1 Radio transmission set (1 x transmitter,

1 x receiver)

2 Wall plug transformers

(9 V

/300 mA)

1 SCART—CINCH adapter IN

1 SCART—CINCH adapter OUT

2 CINCH—Jacks 3,5 mm cable, 3 core

1 CINCH—CINCH cable, 3 core

1 Infrared cable (infrared transmission

diode cable for the remote control

signals to be transmitted)

3 Adhesive pads for the infrared

transmitter diodes

1 AUDIO adapter 3,5 mm stereo jack

on CINCH sockets

1 Operating manual

IB_KH2130_DT35269_LB4BC.indb 2IB_KH2130_DT35269_LB4BC.indb 2 04.09.2009 13:10:06 Uhr04.09.2009 13:10:06 Uhr

- 3 -

Technical data

Power supply:

Transmitter 9 V

/ 300 mA

Receiver 9 V

/ 300 mA

Manufacturer HON-KWANG

ELECTRIC CO., LTD

Model number: HKA-0930EC-230

Input:

230 V

~

/ 50 Hz,

30 mA, 7 W

Output : 9 V

, 300mA 2,7 VA

Protection class: II /

Transmitter connections:

• 9 V

Supply voltage

• 2 x Audio/Video IN (jacks 3,5 mm)

• 1 x TV output (jack 3,5 mm)

• Infrared socket (IR)

Receiver connections:

• 9 V

Supply voltage

• Audio R/L and Video OUT (CINCH)

Operating

temperature:

+5

~

+35°C

Humidity:

5

~

90 %

(no condensation)

Dimensions:

Transmitter/Receiver

unit: 135 x 55 x 145 mm

Weight :

• Receiver approx. 170 g

• Transmitter approx. 185 g

• Mains power adapter approx. 180 g

Video signal: 1 Vss

Audio signal: 1 Vss (type)

Transmission power: 10 mW

Open space range: up to 100 m

Within enclosed buildings or other loca-

tions, transmission disruptions (reflections)

may arise that strongly impair the image

and sound quality.

Safety instructions

Please read the following information •

carefully.

The operating manual must be stored •

safely and passed on to any future

owners of the radio transmission set.

Only use the product for the intended •

purpose as described in this operating

manual.

Risk of electric shocks!

Set up the radio transmission set out-•

side of the reach of children. Never

allow children to play with the radio

transmission set without supervision.

Children could attempt to insert for-

eign objects into the openings in the

device housing.

Only connect the devices to a socket with •

a mains voltage of 230 V

~

/50 Hz

using the supplied mains adapters.

Only plug the mains power adapter •

(wall plug transformer) in the desig-

nated 9 V

connection socket of the

respective device.

Protect the device from moisture. Use •

it only in dry rooms, do not use it out-

doors or close to liquids.

Make sure that neither the device nor •

the mains adapter becomes wet or

damp or sustains any other damage

during use.

When a storm and/or thunderstorm •

with the risk of lightening threatens,

disconnect the mains adapter from the

mains power.

Never allow any fluids to enter into the •

housings of the radio transmission sets.

Never submerse the device in water. •

Wipe it only with a slightly damp cloth.

IB_KH2130_DT35269_LB4BC.indb 3IB_KH2130_DT35269_LB4BC.indb 3 04.09.2009 13:10:06 Uhr04.09.2009 13:10:06 Uhr

- 4 -

Do not operate the device if a mains •

adapter, the adapter's power cable or

the device itself is damaged. Arrange

for a defective mains adapter to be

repaired or replaced as soon as pos-

sible by Customer Services.

You are not permitted to open the •

housing of the radio transmission set

or to modify it in any way. Otherwise,

the warranty becomes void.

Notice regarding power

disconnection:

To completely disconnect the device •

from mains power, the mains adapter

must be unplugged from the wall socket.

For this reason, the device must be

used in a location where unobstructed

access to the power socket is always

assured so that you are able to imme-

diately pull out the power plug in the

event of an emergency. To eliminate

the risk of fire, prevent unintended

activation and save energy costs, the

mains adapter must be unplugged

from the wall socket when the device

is not in use.

Always grasp the mains adapter di-•

rectly when you wish to unplug it. Do

not pull on the cable and never touch

the mains adapter with wet hands,

this could result in a short circuit or

you receiving an electric shock. Do

not place furniture or other objects on

the cable of the mains adapter, and

ensure that it cannot become trapped.

Never make a knot in the power ca-

ble and do not bind it together with

other cables. Run the mains adapter

cable as well as any CINCH or in-

frared cable so that no one will step

on it or trip over it. A damaged mains

adapter can cause a fire or electric

shock. Check the mains adapter from

time to time. Should it become dam-

aged, contact your nearest authorised

customer service centre or your dealer

to have it replaced.

Risk of fire!

Avoid plugging in the wall plug trans-•

former immediately after moving the

radio transmission set from a cold envi-

ronment to a warm one. The tempera-

ture change could result in condensa-

tion that could damage the radio trans-

mission set. Once the radio transmission

set has reached room temperature, it

can be safely put into operation.

Do not place any open fire sources, •

such as candles, directly next to or on

the device.

Do not place any objects filled with •

liquid (e.g. vases) on the device.

The wall plug transformer must not •

be covered because it becomes very

warm during operation.

Risk of suffocation!

Do not leave packaging material lying •

unattended. Plastic foils and bags

and pieces of styropor etc. are not

toys, they can be dangerous for small

children.

IB_KH2130_DT35269_LB4BC.indb 4IB_KH2130_DT35269_LB4BC.indb 4 04.09.2009 13:10:07 Uhr04.09.2009 13:10:07 Uhr

- 5 -

Danger from radio signals!

Do not operate the device in a hospital, •

a hospital operations room or in the

vicinity of medical electronic systems.

The transmitted radio waves could

impair the function of sensitive devices.

Keep the device at least 20 cm away

from pacemakers since the proper

functioning of the pacemaker could

be impaired by radio waves. The trans-

mitted radio waves can cause interfer-

ence noises in audio equipment. Do

not bring the device into the vicinity

of flammable gases or an explosive

environment (e.g. paint shop) while

the radio components are switched on

since the transmitted radio waves could

trigger an explosion or a fire. The

range of the radio waves depends on

ambient and environmental conditions.

Risk of accidents and injury!

This device is not intended for use by •

individuals (including children) with

restricted physical, physiological or

intellectual abilities or deficiences in

experience and/or knowledge un-

less they are supervised by a person

responsible for their safety or receive

from this person instruction in how the

device is to be used. Children must be

supervised to ensure that they do not

play with the device.

Damage to the device

Do not expose the radio transmission •

set to high temperatures, direct sunlight,

severe vibrations or high mechanical

loads.

Do not use any aggressive chemical •

substances for cleaning.

IB_KH2130_DT35269_LB4BC.indb 5IB_KH2130_DT35269_LB4BC.indb 5 04.09.2009 13:10:07 Uhr04.09.2009 13:10:07 Uhr

- 6 -

The device components

Fig. A: The transmitter:

q Transmitter

w LED status indicator

e Switch ROOM 1

r Switch ROOM 2

t Infrared connection socket (IR)

y Output for a TV

u AV input 2

i AV input 1

o Connection socket

a Transmitter's on/off switch

s Transmitter channel toggle switch

(on the underside of the device)

Fig. B: The receiver:

d Receiver

f Infrared receiver

g LED operating indicator

h Audio/Video CINCH outputs

j Connection socket for the supply

voltage

k Receiver's on/off switch

l Reception channel switch (bottom

of device)

1( Wall plug transformer (2 pieces)

2) CINCH—3,5mm jacks cables (2 pieces)

2! SCART—CINCH adapter "IN"

2@ SCART—CINCH adapter "OUT"

2# Infrared cable with 3 transmit diodes

2$ AUDIO adapter 3.5 mm mini-stereo

to CINCH female

2% CINCH—CINCH cable

Putting the device into use

First take all device components from the

packaging and remove all packing foil

and tape.

Important notice:

Even when the system (transmitter +

receiver) is switched off, the manufac-

turer still recommends disconnecting

the wall plug transformer from the

mains power or using a power strip

with a shut-off switch. Only in this way

is complete switch off assured thus

contributing to economical consumer

attitude.

Connecting the transmitter

Note:

You can connect two signal sources.

The signal to be transmitted can be

selected via a switch on the front

panel of the transmitter. Thereby the

radio transmission set can transmit the

image and sound signals of every de-

vice that emits a sound and/or video

signal via a suitable connection:

• DVD Player / CD Player

• VCR

• Television

• SAT receiver/set top box

• Video camera

• Computer video card, etc.

Connecting signal sources to the

transmitter:

On devices with cinch outputs for the •

audio and video signals you connect

these via one of the supplied CINCH—

3,5mm jack cables 2) to the socket

"AV IN 1" i on the rear panel of the

transmitter q.

IB_KH2130_DT35269_LB4BC.indb 6IB_KH2130_DT35269_LB4BC.indb 6 04.09.2009 13:10:07 Uhr04.09.2009 13:10:07 Uhr

- 7 -

Note:

Observe the colour coding:

The white CINCH plug carries the left >

audio channel signal and belongs in

the white CINCH socket.

The red CINCH plug carries the right >

audio channel signal and belongs in

the red CINCH socket.

The yellow CINCH plug carries the >

video signal and belongs in the yellow

CINCH socket.

If required you can connect a second •

device as well, with the transmitter and

for this select the socket "AV IN 2" u.

If the signal source of your signal is •

available via a SCART connection,

you can use the supplied SCART—

CINCH adapter "OUT" 2@ between

the device and the CINCH—3,5mm

jack cable 2).

The A/V output of your signal source •

is now occupied. If you, nevertheless,

want to connect the signal source to

a TV, connect the TV via the socket

"OUTPUT TO TV" y to the transmitter

q. For this you can use either one of

the supplied CINCH—3,5mm jack ca-

bles 2) or, if both are already

occupied, an equivalent cable from

your local dealer.

Infrared connection

You can control the signal source via the

remote control even if you are not in the

same room. The receiver d picks up the

signal and sends it back to the transmitter

q which then redirects the signal via the

infrared cable 2# to the signal source.

For this you connect the supplied infra-•

red cable 2# to the transmitter's infrared

connection socket t.

Remove the protective foil from one •

of the supplied adhesive pads and at-

tach the pad to the rounded off side of

one of the infrared cable's 2# transmis-

sion diodes.

Now remove the 2 protective foils from •

the adhesive pad and attach the trans-

mission diode to the infrared receiver

of your signal source.

Note:

Avoid attaching the full length of the

transmission diode to the infrared

receiver of the signal source. Other-

wise it is possible that direct remote

control commands will no longer be

received.

Proceed in the same manner to con-•

nect further signal sources and/or

other devices that you want to control

with the radio transmission set.

Insert the cable plug of one of the •

supplied wall plug transformers 1( into

the connection socket for the supply

voltage o.

Insert the wall plug transformer • 1( into

a properly connected 230 V

~

/ 50 Hz

mains power socket.

Using a computer as the signal

source

You can also transmit the video signal of

a computer if the computer's video card

has a VIDEO output available.

IB_KH2130_DT35269_LB4BC.indb 7IB_KH2130_DT35269_LB4BC.indb 7 04.09.2009 13:10:07 Uhr04.09.2009 13:10:07 Uhr

- 8 -

For the sound transmissions use, if neces-

sary, the AUDIO adapter 3,5 mm jack on

CINCH sockets 2$, which you connect to

the output of the sound card if this has

no cinch output. The yellow plug of the

CINCH—3,5mm jack cable 2) you con-

nect to the video card's video output.

Tips:

The video card must have an FBAS

output available.

Make sure that the computer is cor-

rectly configured for outputting video

on the video card.

Connecting the receiver

Connect the Audio/Video CINCH out-•

puts h of the receiver d to the A/V in-

puts on the target device, probably a

television set. For this you use the sup-

plied three core CINCH cable 2%. If

necessary, with the aid of the supplied

SCART—CINCH adapter "IN" 2!.

Note:

Be sure to match the colours correctly.

Insert the cable plug of the second •

supplied wall plug transformer 1( into

the connection socket for the supply

voltage j.

Insert the wall plug transformer • 1( into

a properly connected 230 V

~

/ 50 Hz

mains power socket.

Important!

Try, if required, to operate the receiver d

in various locations to avoid cancella-

tion effects and interference and thus

improve the transmission quality.

Switching on

Move the ON/OFF switch • a and k

of the transmitter and receiver to the

"ON" position to switch them both on.

Switch the signal source on and, if •

necessary, start playback.

Switch the TV (target device) on and •

activate the A/V inputs to which you

have connected the receiver.

Select on the transmitter and on the •

receiver, via the CHANNEL switch s

and l, implicitly in each case the

same transmission channel. The radio

transmission should now function.

Note:

The data/signals sent from the transmit-

ter are not encrypted. This means that

compatible devices within the recep-

tion range are capable of eavesdrop-

ping on the signal. The radio transmis-

sion set uses an "open standard".

To switch the signal source AV 1 and/•

or 2 for a TV connected to the trans-

mitter q press the button "ROOM 1" e

(= the room in which the transmitter is

located).

To switch the signal source AV 1 and/•

or 2 for a TV connected to the receiver

d press the button "ROOM 2" r

(= the room in which the receiver is

located).

Point the remote control of the signal •

source to the infrared receiver f of

the receiver d. The commands are

sent to your signal source.

IB_KH2130_DT35269_LB4BC.indb 8IB_KH2130_DT35269_LB4BC.indb 8 04.09.2009 13:10:07 Uhr04.09.2009 13:10:07 Uhr

- 9 -

Improving the transmission quality

You can try the following measures to im-

prove the quality in event of transmission

disruptions:

Change the position and/or direction •

of the transmitter q and/or receiver d.

For problems with the remote control •

signal quality change the position of

the infrared cable's 2# transmission

diodes to the infrared receiver of the

signal source.

Try setting one of the other 4 trans-•

mission channels via the CHANNEL

switch s and l.

Channel configuration

(parallel operation)

You can operate up to 4 radio transmis-

sion sets within close proximity of each

other. Then you select, for each set, their

own channel from the 4 different avail-

able channels.

Expansion options

Expand the radio transmission set by

connecting multiple transmitters q or

receivers d.

Note:

If you want to control a receiver d

selectively with several transmitters q

you should never have several trans-

mitters switched on at the same time.

This prevents transmission disruptions.

Transmitter

Receiver

Cleaning

Risk of electric shock!

Disconnect the wall plug transformer

(1() from the mains power socket

when you want to clean the radio

transmission set.

Important!

Chemical cleansers may damage the

radio transmission set.

Clean the radio transmission set only

with a slightly damp cloth.

Troubleshooting

If a problem arises, please check the fol-

lowing table first. If the problem cannot

be resolved please contact one of the

listed service locations.

No audio/video transmission

Are the transmitter > q and receiver d

switched on?

Are the transmitter channel switch > s

and the receiver channel switch l

set to the same channel?

The range of the radio transmission >

set is reduced by walls and ceilings.

Reduce the distance between the

transmitter q and the receiver d.

IB_KH2130_DT35269_LB4BC.indb 9IB_KH2130_DT35269_LB4BC.indb 9 04.09.2009 13:10:07 Uhr04.09.2009 13:10:07 Uhr

- 10 -

Check the CINCH and AV connec- >

tions on the connected devices as

well as on the transmitter q and the

receiver d.

If you are using other radio devices >

(same frequency), this may result in

disruptions. It may also affect the

range of the radio transmission set.

The signal source must be switched >

on (i.e. DVD player) and playback

started.

Poor transmission quality

Change the direction of the transmit- >

ter q and the receiver d.

Change the channel setting > s/l

on both components. Make sure that

the transmitter q and the receiver d

have the same setting.

If you are using other radio devices >

(same frequency), this may result in

disruptions. It may also affect the

range of the radio transmission set.

Disruptions in remote control

commands

Point your remote control directly at >

the infrared receiver f. Otherwise

the commands cannot be executed.

Fasten the infrared transmission di- >

odes of the infrared cable 2# slightly

offset to the infrared receiver of the

signal source.

If you are using other radio devices >

(same frequency), this may result in

disruptions. It may also affect the

range of the radio transmission set.

Disposal

Do not dispose of the device

in your normal domestic

waste. This product is subject

to the provisions of European

Directive 2002/96/EC.

Arrange for the product, or parts of it, •

to be disposed of by a professional dis-

posal company or by your communal

waste facility.

Observe the currently applicable re-•

gulations. In case of doubt, please

contact your waste disposal centre.

Dispose of packaging materials

in an environmentally responsible

manner.

Importer

KOMPERNASS GMBH

BURGSTRASSE 21

44867 BOCHUM, GERMANY

www.kompernass.com

IB_KH2130_DT35269_LB4BC.indb 10IB_KH2130_DT35269_LB4BC.indb 10 04.09.2009 13:10:07 Uhr04.09.2009 13:10:07 Uhr

- 11 -

Important warranty information

You receive a 3-year warranty for this

device as of the purchase date. Should

you, in spite of our high quality stand-

ards, have grounds for complaint please

contact our Service Hotline. In the event

that processing of your complaint is not

possible by telephone, here you will re-

ceive

a processing number (RMA number) •

as well as

an address to which you can send •

your device for repair under warranty.

In the case of a mail-in shipment please

enclose a copy of the purchase receipt

(sales slip). The device must be securely

packed and the RMA number clearly

visible. Products sent in without an RMA

number cannot be processed.

Note: The warranty provisions cover

only material or manufacturing defects.

The warranty is not valid;

to parts subject to wear and tear•

for damage to breakable parts, such •

as switches or rechargeable batteries.

This product is for private use only and

is not intended for commercial applica-

tions. The warranty is void in the case of

abusive and improper handling, use of

force and internal tampering not carried

out by our authorized service branch.

Your statutory warranty claims are not

restricted by this warranty.

DES Ltd

Tel.: 0870/787-6177

Fax: 0870/787-6168

e-mail: support.uk@kompernass.com

Kompernass Service Ireland

Tel.: 1850 930 412 (0,082 EUR/Min.)

Standard call rates apply. Mobile operators may vary.

e-mail: support.ie@kompernass.com

IB_KH2130_DT35269_LB4BC.indb 11IB_KH2130_DT35269_LB4BC.indb 11 04.09.2009 13:10:07 Uhr04.09.2009 13:10:07 Uhr

- 12 -

IB_KH2130_DT35269_LB4BC.indb 12IB_KH2130_DT35269_LB4BC.indb 12 04.09.2009 13:10:07 Uhr04.09.2009 13:10:07 Uhr

- 13 -

Pred prvo uporabo ta navodila pozorno preberite in jih shranite za poznejšo uporabo.

Ob predaji naprave tretji osebi zraven priložite tudi ta navodila za uporabo.

KAZALO VSEBINE STRAN

Predvidena uporaba 14

Vsebina kompleta 14

Tehnični podatki 15

Varnostni napotki 15

Sestavni deli izdelka 18

Zagon naprave 18

Priklop oddajnika 18

Priklop sprejemnika 20

Vklop 20

Kakovost prenosa 21

Nastavitev kanalov (vzporedno delovanje) 21

Možne razširitve 21

Čiščenje 21

Iskanje in odprava napak 21

Odstranitev 22

Proizvajalec 22

Pomembni napotki o garanciji 23

IB_KH2130_DT35269_LB4BC.indb 13IB_KH2130_DT35269_LB4BC.indb 13 04.09.2009 13:10:07 Uhr04.09.2009 13:10:07 Uhr

- 14 -

Predvidena uporaba

Napravo je dovoljeno uporabljati izključno

za zasebne namene. Komplet za prenos

signalov je namenjen za avdio in video

naprave, kot so npr.

televizijski sprejemnik,•

satelitski sprejemnik in digitalni •

pretvornik (STB),

predvajalnik plošč DVD/CD,•

računalnik (PC),•

itd.,•

ki imajo vhode in izhode AV. Predvidena

uporaba kompleta za prenos signalov

obsega:

brezžičen prenos avdio, video•

in infrardečih signalov

(na prostem je možen prenos

do okrog 100 metrov!).

Za škodo, ki nastane zaradi nepredvidene

uporabe naprave, ne prevzamemo nobe-

ne odgovornosti!

Vsebina kompleta

1 komplet za prenos signalov

(1 oddajnik, 1 sprejemnik)

2 omrežna napajalnika

(9 V

/300 mA)

1 SCART—CINCH adapter IN

1 SCART—CINCH adapter OUT

2 CINCH—3,5-mm zatični vtič,

3-žilni kabel

1 CINCH—CINCH kabel, 3-žilni

1 infrardeči kabel (kabel z infrardečo

oddajno diodo za prenos signalov

daljinskega upravljalnika)

3 lepilne blazinice za infrardeče

oddajne diode

1 AVDIO adapter, 3,5 mm stereo zatični

vtič na CINCH vtičnicah

1 navodila za uporabo

IB_KH2130_DT35269_LB4BC.indb 14IB_KH2130_DT35269_LB4BC.indb 14 04.09.2009 13:10:07 Uhr04.09.2009 13:10:07 Uhr

- 15 -

Tehnični podatki

Napajanje:

Oddajnik 9 V

/300 mA

Sprejemnik 9 V

/300 mA

Proizvajalec HON-KWANG

ELECTRIC CO., LTD

Številka modela: HKA-0930EC-230

Vhod:

230 V

~

/ 50 Hz,

30 mA, 7 W

Izhod: 9 V

, 300 mA 2,7 VA

Razred zaščite: II /

Priključki oddajnika:

• 9 V

napajanje

• 2 x avdio/video IN (zatični vtič 3,5 mm)

• 1 x TV-izhod (zatični vtič 3,5 mm)

• Infrardeča vtičnica (IR)

Priključki sprejemnika:

• 9 V

napajanje

• Avdio R/L in video OUT (CINCH)

Obratovalna

temperatura:

+5

~

+35 °C

Vlaga:

5

~

90 %

(brez kondenzacije)

Mere:

Enota oddajnika/sprejemnika:

135 x 55 x 145 mm

Teža:

• sprejemnik ca. 170 g

• oddajnik ca. 185 g

• omrežni adapter ca. 180 g

Video signal: 1 Vss

Avdio signal: 1 Vss (tip)

Oddajna moč: 10 mW

Doseg na prostem: do 100 m

V zaprtih delih zgradb ali na drugih krajih

lahko pride do motenj pri prenosu zaradi

odboja signala, ki močno poslabšajo ka-

kovost slike in zvoka.

Varnostni napotki

Naslednje informacije skrbno preberite.•

Navodila za uporabo skrbno hranite. •

Če boste komplet za prenos signalov

izročili tretjim osebam, jim hkrati s kom-

pletom obvezno izročite tudi navodila

za uporabo.

Izdelek uporabljajte le za predvidene •

namene, navedene v teh navodilih za

uporabo.

Nevarnost zaradi

električnega udara!

Komplet za prenos signalov shranjujte •

izven dosega otrok. Otrokom ne dovo-

lite, da bi se brez nadzora igrali s kom-

pletom za prenos signalov. Otroci bi

namreč lahko skozi odprtine na ohišju

v izdelek potisnili različne predmete.

Izdelke s priloženima električnima •

adapterjema priklapljajte izključno

v električne vtičnice z napetostjo

230 V

~

/50 Hz.

Omrežna adapterja (omrežna napajal-•

nika z vtičem) priklapljajte le v označe-

ne 9 V

priključne vtičnice ustrezne

naprave.

Izdelek zaščitite pred vlago. Izdelek •

uporabljajte le v suhih prostorih, ne na

prostem ali v bližini tekočin.

Pazite, da se izdelek in omrežni adap-•

ter med delovanjem ne bosta mogla

zmočiti, navlažiti ali poškodovati.

Pred nevihtami in/ali viharji z nevar-•

nostjo udara strele omrežne adapterje

izklopite iz omrežnih vtičnic.

Poskrbite, da v ohišja kompleta za •

prenos signalov nikoli ne bodo stekle

tekočine.

Naprave ne potapljajte v vodo. Čistite •

jo le z rahlo navlaženo krpo.

IB_KH2130_DT35269_LB4BC.indb 15IB_KH2130_DT35269_LB4BC.indb 15 04.09.2009 13:10:07 Uhr04.09.2009 13:10:07 Uhr

- 16 -

Izdelka ne uporabljajte, če so omrežni •

adapter, njegov kabel ali naprava

sama poškodovani. Pokvarjene omre-

žne adapterje dajte takoj popraviti

oz. jih zamenjati z novimi na servisu.

Ohišja kompleta za prenos signalov •

ni nikoli dovoljeno odpirati ali prede-

lovati. V nasprotnem primeru garanci-

ja preneha veljati.

Napotek o ločitvi od omrežja:

Za popoln izklop naprave iz električ-•

nega omrežja je potrebno omrežne

adapterje potegniti iz omrežnih vtičnic.

Zaradi tega izdelek morate uporabljati

tako, da boste vedno imeli neoviran

dostop do omrežne vtičnice in boste

lahko v primeru sile omrežne adapterje

takoj izklopili iz omrežne vtičnice. Da

ne bi prišlo do požara ali nenamerne-

ga vklopa, in zaradi prihranka električ-

ne energije morate omrežne adapterje,

ko izdelka ne uporabljate, praviloma

vedno izklopiti iz omrežnih vtičnic.

Ko omrežni adapter želite izklopiti iz •

omrežne vtičnice, vedno primite za

sam adapter. Ne vlecite za kabel in

se adapterja tudi nikoli ne dotikajte

z mokrimi rokami, ker to lahko povzroči

kratki stik ali električni udar. Na kabel

omrežnega adapterja ne postavljajte

pohištva ali podobnega in pazite, da

ne bo nikjer priprt. Kabla nikoli ne za-

vozlajte in ga ne povezujte z drugimi

kabli. Kabel omrežnega adapterja, pa

tudi CINCH kabel in infrardeči kabel

položite tako, da nihče ne bo mogel

stopiti nanje oz. se obnje spotakniti.

Poškodovan omrežni adapter lahko

povzroči požar ali električni udar.

Zato omrežni adapter občasno pre-

glejte. Če je poškodovan, se obrnite

na najbližji pooblaščeni servis oz.

na trgovca, kjer vam bodo adapter

zamenjali.

Nevarnost požara!

Ko komplet za prenos signalov pri-•

nesete iz hladnega v topel prostor,

omrežnih napajalnikov ne priklapljajte

takoj. V nasprotnem primeru lahko

kondenzirana voda komplet za pre-

nos signalov uniči. Ko se komplet za

prenos signalov segreje na sobno tem-

peraturo, ga lahko uporabljate brez

nevarnosti, da bi se uničil.

Neposredno pred oz. na izdelek ne •

polagajte gorečih predmetov, npr.

sveč.

Na izdelek tudi ne polagajte s tekočino •

napolnjenih predmetov (npr. vaz).

Omrežnih napajalnikov ni dovoljeno •

pokrivati, ker se med delovanjem zelo

segrejejo.

Nevarnost zadušitve!

Embalaže ne puščajte ležati naokoli. •

Plastične folije in vrečke, deli iz stiro-

pora itd. niso igrače in so lahko nevar-

ni za otroke.

IB_KH2130_DT35269_LB4BC.indb 16IB_KH2130_DT35269_LB4BC.indb 16 04.09.2009 13:10:08 Uhr04.09.2009 13:10:08 Uhr

- 17 -

Nevarnost zaradi radijskih

signalov!

Naprave ne uporabljajte v bolnišnici, •

operacijski dvorani ali v bližini medi-

cinskih elektronskih sistemov. Odda-

jani radijski valovi lahko motijo de-

lovanje občutljivih naprav. Napravo

približajte srčnemu spodbujevalniku le

do 20 cm razdalje, sicer lahko radijski

valovi negativno vplivajo na pravilno

delovanje srčnega spodbujevalnika.

Oddani radijski valovi lahko motijo

slušne aparate. Naprave z vklopljeno

radijsko komponento ne prinašajte v

bližino vnetljivih plinov ali v eksploziv-

no okolje (npr. v lakirnico), ker lahko

oddajani radijski valovi povzročijo

eksplozijo ali požar. Doseg radijskih

valov je odvisen od okolice, kjer se

naprava nahaja.

Nevarnost nesreče in telesnih

poškodb!

Ta izdelek ni namenjen temu, da bi •

ga uporabljale osebe (tudi otroci ne)

z omejenimi fizičnimi, zaznavnimi ali

duševnimi sposobnostmi ali s pomanj-

kljivimi izkušnjami in/ali znanjem, ra-

zen pod nadzorom osebe, ki je zanje

odgovorna ali jim je dala navodila v

zvezi z uporabo izdelka. Otroke je

treba nadzorovati, da se z izdelkom

ne bi igrali.

Poškodbe naprave

Kompleta za prenos signalov ne •

izpostavljajte visokim temperaturam,

neposrednim sončnim žarkom ali moč-

nim tresljajem ter mehanskim obreme-

nitvam.

Za čiščenje ne uporabljajte agresivnih •

kemičnih snovi.

IB_KH2130_DT35269_LB4BC.indb 17IB_KH2130_DT35269_LB4BC.indb 17 04.09.2009 13:10:08 Uhr04.09.2009 13:10:08 Uhr

- 18 -

Sestavni deli izdelka

Slika A: Oddajnik:

q Oddajnik

w LED-prikaz delovanja

e Stikalo ROOM 1

r Stikalo ROOM 2

t Infrardeči priključni konektor (IR)

y Izhod za televizor

u AV-vhod 2

i AV-vhod 1

o Priključni konektor za napajanje

a Stikalo za vklop/izklop oddajnika

s Preklopnik oddajnega kanala

(spodnja stran naprave)

Slika B: Sprejemnik:

d Sprejemnik

f Infrardeči sprejemnik

g LED-prikaz delovanja

h CINCH izhodi za avdio/video

j Priključni konektor za napajanje

k Stikalo za vklop/izklop sprejemnika

l Preklopnik sprejemnega kanala (na

spodnji strani naprave)

1( Omrežni napajalnik (2 kosa)

2) CINCH—3,5-mm zatični vtič (2 kabla)

2! SCART—CINCH adapter „IN“

2@ SCART—CINCH adapter „OUT“

2# Infrardeči kabel s 3 oddajnimi

diodami

2$ AVDIO adapter s 3,5-mm zatičnim

vtičem na CINCH vtičnicah

2% CINCH—CINCH kabel

Zagon naprave

Najprej iz embalaže vzemite vse dele

kompleta in z njih odstranite vse emba-

lažne in nalepljene zaščitne folije.

Vnaprejšnje pomembno

opozorilo:

Poleg izklopa naprav (oddajnika in

sprejemnika) proizvajalec priporoča,

da iz omrežnih vtičnic izklopite tudi

omrežna napajalnika ali pa uporabite

električni razdelilec s stikalom za iz-

klop. Le tako bo izklop popoln, prispe-

val pa bo tudi k varčevanju z energijo.

Priklop oddajnika

Opozorilo:

Priključite lahko dva vira signalov.

Signal za prenos lahko izberete

s pomočjo stikala na sprednji strani

oddajnika. Pri tem lahko komplet za

prenos signalov prenaša slikovne in

zvočne signale iz vsake naprave, ki

oddaja zvočni oz. video signal preko

ustreznega priključka:

• DVD-predvajalnik/CD-predvajalnik

• videorekorder

• televizijski sprejemnik

•satelitski sprejemnik/digitalni

pretvornik (STB)

• video kamera

• računalniška grafična kartica itd.

Priklop virov signalov na oddajnik:

Pri napravah s cinch izhodi za avdio in •

video signale te povežete s pomočjo

enega od priloženih kablov CINCH—

3,5-mm zatični vtič 2) z vtičnico „AV IN

1“ i na hrbtni strani oddajnika q.

IB_KH2130_DT35269_LB4BC.indb 18IB_KH2130_DT35269_LB4BC.indb 18 04.09.2009 13:10:08 Uhr04.09.2009 13:10:08 Uhr

Stránka sa načítava ...

Silvercrest KH 2130 Operating Instructions Manual

Silvercrest KH 2130 Operating Instructions Manual

V iných jazykoch

Súvisiace články

Ďalšie dokumenty