Simplicity 580447-0313-E2 Používateľská príručka

Značka: Simplicity

Model: 580447-0313-E2

Kategória: Príslušenstvo motorových vozidiel

Typ: Používateľská príručka

Táto príručka je tiež vhodná pre

English

Slovenija

bg cs hret hu

Èeština

lt lv pl ro ru

eesti keel Hrvatski Latviešu Polski Ðóññêèé

Românã

Áúëãàðñêè LietuviųMagyar

Operator’s Manual

Èíñòðóêöèè çà åêñïëîàòàöèÿ

Návod k obsluze

Kasutusjuhend

Priruènik za operatora

Kezelési útmutató

Naudojimo instrukcija

Operatora rokasgrāmata

Instrukcja obs³ugi

Manual de utilizare

Ðóêîâîäñòâî ïî ýêñïëóàòàöèè

Priroènik za uporabo

Form No. 277108EST

Revision: E

01999-B8011

E 2010 Briggs & Stratton Corporation,

Briggs & Stratton is a registered trademark

of Briggs & Stratton Corporation

Model 580000

Vanguardt

Gasoline

Not for Reproduction

BRIGGSandSTRATTON.COM

4 5

Not for Reproduction

6 7

9 10

Not for Reproduction

4 BRIGGSandSTRATTON.COM

General Information

This manual contains safety information to make you aware of the hazards and risks

associated with engines and how to avoid them. It also contains instructions for the

proper use and care of the engine. Because Briggs & Stratton Corporation does not

necessarily know what equipment this engine will power, it is important that you read and

understand these instructions and the instructions for the equipment. Save these

original instructions for future reference.

For replacement parts or technical assistance, record below the engine model, type, and

code numbers along with the date of purchase. These numbers are located on y our

engine (see the Features and Controls page).

Date of purchase:

Engine model:

MM/DD/YYYY

Model: Code:Type:

Engine Power Rating Information

For 3/LC engines, gross power ratings are based on SAE J1995 criteria and net power

ratings are based on SAE J1349 criteria. Actual power output of production engines

installed in applications may vary depending on a number of factors, including the engine

RPM limit of the application, environment al conditions, engine/equipment maintenance,

and other variables.

Operator Safety

Explosion

Toxic Fumes

Moving Parts

Shock

Hot Surface

Kickback

Fire

Fuel Shutoff

Read Manual

Choke

Oil

Fuel

On Off

Wear Eye

Protection

Slow

Fast

SAFETY AND CONTROL SYMBOLS

Hazardous

Chemical

Frostbite

Hot Liquid or

Steam

Stop

The safety alert symbol is used to identify safety information about hazards that can

result in personal injury. A signal word (DANGER, WARNING, or CAUTION) is used with the

alert symbol to indicate the likelihood and the potential severity of injury. In addition, a hazard

symbol may be used to represent the type of hazard.

DANGER indicates a hazard which, if not avoided, will result in death or

serious injury.

WARNING indicates a hazard which, if not avoided, could result in death or

serious injury.

CAUTION indicates a hazard which, if not avoided, could result in minor or

moderate injury.

NOTICE indicates a situation that could result in damage to the product.

WARNING

Certain components in this product and its related accessories contain

chemicals known to the State of California to cause cancer, birth defects, or

other reproductive harm. Wash hands after handling.

WARNING

The engine exhaust from this product contains chemicals known to the

State of California to cause cancer, birth defects, or other reproductive

harm.

WARNING

Briggs & Stratton does not approve or authorize the use of these engines

on 3-wheel All Terrain Vehicles (ATVs), motor bikes, fun/recreational

go-karts, aircraft products, or vehi cles intended for use in competitive

events. Use of these engines in such applications could result in property

damage, serious injury (including paralysis), or even death.

NOTICE: This engine was shipped from Briggs & Stratton without oil. Before you start

the engine, make sure you add oil according to the instructions in this manual. If you

start the engine without oil, it will be damaged beyond repair and will not be covered

under warranty.

WARNING

Fuel and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

When Adding Fuel

• Turn engine off and let engine cool at least 2 minutes before removing the fuel

cap.

• Fill fuel tank outdoors or in well -ventilated area.

• Do not overfill fuel tank. To allow for expansion of the fuel, do not fill above the

bottom of the fuel tank neck.

• Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition

sources.

• Check fuel lines, tank, cap, and fittings frequently for cracks or leaks.

Replace if necessary

• If fuel spills, wait until it evaporates before starting engine.

When Starting Engine

• Ensure that spark plug, muffler, fuel cap and air cleaner (if equipped) are in

place and secured.

• Do not crank engine with spark plug removed.

• If engine floods, set choke (if equipped) to OPEN/RUN position, move throttle

(if equipped) to FAST position and crank until engine starts.

When Operating Equipment

• Do not tip engine or equipment at angle which causes fuel to spill.

• Do not choke the carburetor to stop engine.

• Never start or run the engine with the air cleaner assembly (if equipped) or the

air filter (if equipped) removed.

When Transporting Equipment

• Transport with fuel tank EMPTY or with fuel shut-off valve OFF.

When Storing Fuel Or Equipment With Fuel In Tank

• Store away from furnaces, stoves, water heaters or other appliances that have

pilot lights or other ignition sources because they can ignite fuel vapors.

Starting engine creates sparking.

Sparking can ignite nearby flammable gases.

Explosion and fire could result.

WARNING

• If there is natural or LP gas leakage in area, do not start engine.

• Do not use pressurized starting fluids because vapors are flammable.

Engines give off carbon monoxide, an odorless, colorless, poison gas.

Breathing carbon monoxide can cause nausea, fainting or death.

WARNING

• Start and run engine outdoors.

• Do not start or run engine in enclosed area, even if doors or windows are open.

Not for Reproduction

Rotating parts can contact or entangle hands, feet, hair, clothing, or

accessories.

Traumatic amputation or severe laceration can result.

WARNING

• Operate equipment with guards in place.

• Keep hands and feet away from rotating parts.

• Tie up long hair and remove jewelry.

• Do not wear loose-fitting clothing, dangling drawstrings or items that could

become caught.

Running engines produce heat. Engine parts, especially muffler,

become extremely hot.

Severe thermal burns can occur on contact.

Combustible debris, such as leaves, grass, brush, etc. can catch fire.

WARNING

• Allow muffler, engine cylinder and fins to cool before touching.

• Remove accumulated debris from muffler area and cylinder area.

• It is a violation of California Public Resource Code, Section 4442, to use or

operate the engine on any forest -covered, brush-covered, or grass-covered land

unless the exhaust system is equipped with a spark arrester, as defined in

Section 4442, maintained in effective working order. Other states or federal

jurisdictions may have similar laws. Contact the original equipment

manufacturer, retailer, or dealer to obtain a spark arrester designed for the

exhaust system installed on this engine.

Severe thermal burns can occur by escaping steam or hot coolant.

WARNING

• DO NOT remove radiator cap or reservoir cap if engine is warm or running.

• Stop engine and allow it to cool before removing radiator cap or reservoir cap

and before changing or adding coolant.

Unintentional sparking can result in fire or electric shock.

Unintentional start-up can result in entanglement, traumatic

amputation, or laceration.

Fire hazard

WARNING

Before performing adjustments or repairs:

• Disconnect the spark plug wire and keep it away from the spark plug.

• Disconnect battery at negative terminal (only engines with electric start.)

• Use only c orrect tools.

• Do not tamper with governor spring, links or other parts to increase engine

speed.

• Replacement parts must be of the same design and installed in the same

position as the original parts. Other parts may not perform as well, may damage

the unit, and may result in injury.

• Do not strike the flywheel with a hammer or hard object because the flywheel

may later shatter during operation.

When testing for spark:

• Use approved spark plug tester.

• Do not check for spark with spark plug removed.

Not for Reproduction

6 BRIGGSandSTRATTON.COM

Features and Controls

Compare illustration

with your engine to familiarize yourself with the location of

various features and controls.

A. Engine Identification

Model Type Code

B. Spark Plug

C. Dipstick

D. Oil Fill

E. Oil Filter

F. Oil Drain Plug

G. Oil Pressure Sensor

H. Electric Starter

I. Carburetor

J. Thermostat

K. Ignition Coil

L. Oil Pan

M. Alternator

N. Coolant Temperature Sending Unit

O. Engine Date Code

P. Fan

Operation

Oil capacity (see the Specifications section)

Oil Recommendations

We recommend the use of Briggs & Stratton Warranty Certified oils for best

performance. Other high-quality detergent oils are acceptable if classified for service SF,

SG, SH, SJ or higher. Do not use special additives.

Outdoor temperatures determine the proper oil viscosity for the engine. Use the chart to

select the best viscosity for the outdoor temperature range expected.

* Below 40°F(4°C) the use of SAE 30 will result in hard starting.

** Above 80°F(27°C) the use of 10W-30 may cause increased oil consumption. Check

oil level more frequently.

How To Check/Add Oil - Figure

2 3

Before adding or checking the oil

• Place engine level.

• Clean the oil fill area of any debris.

1. Remove the dipstick (A) and wipe with a clean cloth (Figure 2).

2. Completely insert the dipstick.

3. Remove the dipstick and check the oil level. It should be at the FULL mark (B)onthe

dipstick.

4. If the oil is low, remove the oil fill cap (J).

5. Remove the dipstick. Pour the oil slowly into the engine oil fill (C). Do not overfill.

Important: When adding oil, adequate venting is required as follows:

• Remove the dipstick.

• Make sure adequate clearance (D) is maintained between the oil fill device (E)

and the engine oil fill (C).SeeFigure3.

6. Install and tighten the oil fill cap.

NOTICE: Before starting the engine, wipe the engine clean of any spilled oil.

7. After adding oil, install the dipstick. Start and run engine at idle for five minutes. See

the How To Start The Engine section. Shut off engine. Wait three minutes and

check oil level. If required, add oil to bring oil level to the FULL mark (B)onthe

dipstick (Figure 2).

8. Install the dipstick.

Oil Pressure

If the oil pressure is too low, a pressure switch (if equipped) will either stop the engine or

activate a warning device on the equipment. If this occurs, stop the engine and check the

oil level with the dipstick.

If the oil level is below the ADD mark, add oil until it reaches the FULL mark. Start the

engine and check for proper pressure before continuing to operate.

If the oil level is between the ADD and FULL marks, do not start the engine. Contact

any Briggs & Stratton 3/LC Authorized Dealer to have the oil pressure problem

corrected.

Fuel Recommendations

Fuel must meet these requirements:

• Clean, fresh, unleaded gasoline.

• A minimum of 87 octane/87 AKI (91 RON). High altitude use, see below.

• Gasoline with up to 10% ethanol (gasohol) or up to 15% MTBE (methyl tertiary

butyl ether) is acceptable.

CAUTION: Do not use unapproved gasolines, such as E85. Do not mix oil in gasoline or

modify the engine to run on alternate fuels. This will damage the engine components and

void the engine warranty.

To protect the fuel system from gum formation, mix a fuel stabilizer into the fuel. See

Storage. All fuel is not the s ame. If starting or performance problems occur, change fuel

providers or change brands. This engine is certified to operate on gasoline. The

emissions control system for this engine is EM (Engine Modifications).

High Altitude

At altitudes over 3,000 feet (900 meters), a minimum 85 octane/85 AKI (89 RON)

gasoline is acceptable. To remain emissions compliant, high altitude adjustment is

required. Operation without this adjustment will cause decreased performance,

increased fuel consumption, and increased emissions. See a Briggs & Stratton 3/LC

Authorized Dealer for high altitude adjustment information.

Operation of the engine at altitudes below 2,500 feet (762 meters) with the high altitude

kit is not recommended.

How To Add Fuel - Figure

WARNING

Fuel and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

When Adding Fuel

• Turn engine off and let engine cool at least 2 minutes before removing the fuel

cap.

• Fill fuel tank outdoors or in well -ventilated area.

• Do not overfill fuel tank. To allow for expansion of the fuel, do not fill above the

bottom of the fuel tank neck.

• Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition

sources.

• Check fuel lines, tank, cap, and fittings frequently for cracks or leaks.

Replace if necessary

• If fuel spills, wait until it evaporates before starting engine.

1. Clean the fuel cap area of dirt and debris. Remove the fuel cap (A, Figure 4).

2. Fill the fuel tank (B) with fuel. To allow for expansion o f the fuel, do not fill above the

bottom of the fuel tank neck (C).

3. Reinstall the fuel cap.

Coolant Recommendations

Coolant capacity (see the equipment manufacture’s manual)

NOTICE: This is a liquid-cooled engine. A 50/50% mixture of phosphate-free antifreeze

and tap water is required for cooling, rust resistance, and lubrication of the water pump.

Not for Reproduction

How To Check/Add Coolant

Severe thermal burns can occur by escaping steam or hot coolant.

WARNING

• DO NOT remove radiator cap or reservoir cap if engine is warm or running.

• Stop engine and allow it to cool before removing radiator cap or reservoir cap

and before changing or adding coolant.

1. Before operating, check the coolant level. The coolant level must be between the

FULL and the LOW/ADD marks on the coolant reservoir. If the coolant level is low,

add a 50/50% coolant mixture of phosphate-free antifreeze and tap water to the

reservoir.

2. To remove the reservoir cap after engine is cool, place a thick cloth over the reservoir

cap. Slowly turn the reservoir cap counterclockwise to remove.

3. If the reservoir is dry, then add coolant to both the reservoir and to the radiator. See

the equipment manual for location, operation, and maintenance of the coolant

reservoir and the radiator.

4. To remove the radiator cap after engine is cool, place a thick cloth over the radiator

cap. Slowly turn the radiator cap counterclockwise to the first stop. If pressurized

steam escapes from the cap, stand back to avoid injury. After all pressure is

released, push down and turn the radiator cap counterclockwise to remove.

Gauges And Lights

The gauges and lights shown are typical and represent various options that can be used.

See the equipment manual for location and operation of gauges and lights.

Coolant Temperature Gauge

Indicates coolant temperature when the electric start switch is in

the ON position.

Normal range 80º -- 9 0 º C (175º -- 195º F)

Dangerous range above 105º C (220º F)

Hour Meter Gauge

Indicates the total number of operating hours.

Fuel Gauge

Indicates the fuel remaining in the fuel tank. To minimize condensation,

keep the fuel tank full.

Temperature Light

If the temperature light comes on, the engine is overheating. Stop the

engine and check the coolant level (see the How To Check Coolant

section). Check the radiator for debris that could restrict air flow.

Ignition Light

When the electric start switch is turned to the ON position, the ignition light

should be on. When the engine is running, the ignition light should go out.

If the ignition light is out when then electric startswitchintheONposition, check for a

blown fuse.

Engine Oil Pressure Light

When the electric start switch is turned to the ON position, the engine oil

pressure light should be on. When the engine is running, the engine oil

pressure light should go out. If the engine oil pressure light comes on when the engine

is running, immediately stop the engine. First, check the oil level (see the How To

Check/Add Oil section). Next, check the electrical system.

Charge Light

When the electric start switch is turned to the ON position, the charge light

should be on. When the engine is running, the charge light should go out. If

the charge light comes on when the engine is running, check the electrical system.

How To Start The Engine - Figure

WARNING

Fuel and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

When Starting Engine

• Ensure that spark plug, muffler, fuel cap and air cleaner (if equipped) are in

place and secured.

• Do not crank engine with spark plug removed.

• If engine floods, set choke (if equipped) to OPEN/RUN position, move throttle

(if equipped) to FAST position and crank until engine starts.

Starting engine creates sparking.

Sparking can ignite nearby flammable gases.

Explosion and fire could result.

WARNING

• If there is natural or LP gas leakage in area, do not start engine.

• Do not use pressurized starting fluids because vapors are flammable.

Engines give off carbon monoxide, an odorless, colorless, poison gas.

Breathing carbon monoxide can cause nausea, fainting or death.

WARNING

• Start and run engine outdoors.

• Do not start or run engine in enclosed area, even if doors or windows are open.

NOTICE: This engine was shipped from Briggs & Stratton without oil. Before you start

the engine, make sure you add oil according to the instructions in this manual. If you

start the engine without oil, it will be damaged beyond repair and will not be covered

under warranty.

Note: Some engines and equipment have remote controls. See the equipment manual

for location and operation of remote controls.

1. Check the oil level. See the How To Check/Add Oil section.

2. Make sure equipment drive controls, if equipped, are disengaged.

3. Turn the fuel shut-off valve (A), if equipped, to the on position (Figure 5).

4. Move the throttle control (B) slightly past t he slow

position.

5. Turn the electric start switch (D) to the on/start position (Figure 5).

NOTICE: To prolong starter life, use short starting cycles, not to exceed 15 seconds

per minute. Extended cranking c an damage the starter motor.

6. If the engine does not immediately start, pull out the choke control ( C), if equipped, to

the c hoke

position.

Note: Choke is usually unnecessary when restarting a warm engine.

7. As the engine warms up, move the choke control (C)totherun

position.

How To Stop The Engine - Figure

WARNING

Fuel and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

• Do not choke the carburetor to stop engine.

1. Move the throttle control (B) to the slow

position. Turn the key switch (D)to

the off position (Figure 5). Remove the k ey and keep in a safe place out of the reach

of children.

2. After the engine stops, turn the fuel shut-off valve ( A), if equipped, to the closed

position.

Maintenance

We recommend that you see any Briggs & Stratton 3/LC Authorized Dealer for all

maintenance and service of the engine and engine parts.

NOTICE: All the components used to build this engine must remain in place for proper

operation.

Not for Reproduction

BRIGGSandSTRATTON.COM

Emissions Control

Maintenance, replacement, or repair of the emissions control devices and systems

may be performed by any non-road engine repair establishment or individual.

However, to obtain “no charge” emissions control service, the work must be performed

by a factory authorized dealer. See the Emissions Warranty.

Unintentional sparking can result in fire or electric shock.

Unintentional start-up can result in entanglement, traumatic

amputation, or laceration.

Fire hazard

WARNING

Before performing adjustments or repairs:

• Disconnect the spark plug wire and keep it away from the spark plug.

• Disconnect battery at negative terminal (only engines with electric start.)

• Use only c orrect tools.

• Do not tamper with governor spring, links or other parts to increase engine

speed.

• Replacement parts must be of the same design and installed in the same

position as the original parts. Other parts may not perform as well, may damage

the unit, and may result in injury.

• Do not strike the flywheel with a hammer or hard object because the flywheel

may later shatter during operation.

When testing for spark:

• Use approved spark plug tester.

• Do not check for spark with spark plug removed.

Maintenance Chart

Every8HoursorDaily

• Check engine oil level

• Check coolant level

First 50 Hours (initial Break-In)

• Change engine oil *

Every 100 Hours or Annually

• Check fan belt tension

• Clean radiator

• Clean air filter

• Check muffler and clean spark arrestor (if equipped)

Every 150 Hours or Annually

• Change engine oil *

• Replace oil filter

Every 600 Hours or Annually

• Replace air filter

• Check valve clearance H

• Replace fuel filter

• Replace spark plugs

Annually

• Change coolant

* Service more often when operating under heavy load or in high temperature.

H Not required unless engine performance problems are noted.

Carburetor Adjustment

Never make adjustments to the carburetor. The carburetor was set at the factory to

operate efficiently under most conditions. However, if adjustments are required, see a

Briggs & Stratton 3/LC Authorized Dealer for service.

NOTICE: The manufacturer of the equipment on which this engine is installed s pecifies

the top speed at which the engine will be operated. Do not exceed this speed.

How To Replace The Spark Plug - Figure

Check the gap (A, Figure 6) with a wire gauge (B). If necessary, reset the gap. Install

and tighten the spark plug to the recommended torque. For gap setting or torque, see the

Specifications section.

Note: In some areas, local law requires using a resistor spark plug to suppress ignition

signals. If this engine was originally equipped with a resistor spark plug, use the same

type for replacement.

Inspect Muffler And Spark Arrester