Philco PEI 4701 Návod na obsluhu

RANGE HOOD

USER'S MANUAL

PEI 4701

Dear customer,

Thank you for buying a PHILCO brand product. So that your appliance serves you well, please read all

the instructions in this user's manual.

EN - 1

CONTENTS

PART 1: IMPORTANT SAFETY INSTRUCTIONS ................................................................................................ 2

PART 2: DESCRIPTION OF THE APPLIANCE .................................................................................................... 4

PART 3: INSTALLATION .................................................................................................................................... 5

Unpacking ..................................................................................................................................................................................................5

Dimensions of the appliance ..............................................................................................................................................................5

Placement ..................................................................................................................................................................................................6

Assembly and installation ....................................................................................................................................................................6

Carbon  lter............................................................................................................................................................................................10

Ventilation ............................................................................................................................................................................................... 11

PART 4: OPERATION ....................................................................................................................................... 12

Operating tips ........................................................................................................................................................................................ 12

PART 5: MAINTENANCE AND CLEANING ...................................................................................................... 13

Changing a light bulb ......................................................................................................................................................................... 13

Cleaning ...................................................................................................................................................................................................14

PART 6: BEFORE YOU CALL THE SERVICE CENTRE ....................................................................................... 15

PART 7: TECHNICAL SPECIFICATIONS ........................................................................................................... 16

EN - 2

PART 1: IMPORTANT SAFETY INSTRUCTIONS

Recommendation:

Carefully read these instructions before installing and operating this range hood.

Write down the serial number found on the rating label of the range hood in the space below. It is essential that

you store this user's manual in a safe place so that you can use it in the future. If you intend to sell the appliance,

give it to another owner, or if you move, always make sure that the user's manual is attached to the appliance,

so that the new owner can also learn about the operation of the appliance and the relevant warnings.

SERIAL NUMBER:

Important safety instructions

 This appliance is designed for household use only.

 Before connecting the power cord plug, make sure the voltage stated on the rating label of the appliance

corresponds to the voltage in your wall socket. Connect the power cord plug to a power socket with

a voltage of 220 – 240 V ~ 50 Hz.

 Only use a properly grounded power socket. The appliance may only be connected to a properly grounded

power socket.

 All electrical connections must be performed by a quali ed electrician.

 Installation performed by an unquali ed person may cause incorrect operation, damage to the appliance,

create a  re hazard or cause injury to persons.

 Neither the manufacturer nor the vendor take responsibility for damages cause by incorrect or

unprofessional installation, connection or operation. Tampering with the appliance by an unquali ed

person will void the customer's right to a warranty repair.

 Do not expose the power cord to excessive pressure or loads, do not place heavy objects on it, it must

not be tangled and it must not be stepped on. Do not locate the power cord in or on heat sources such

as stoves, heating or other generators of heat. Otherwise this may damage the power cord or create a  re

hazard.

 Only connect the power cord plug to a power socket after the entire installation is completed.

 The power plug serves as a disconnection device and for this reason the power socket must remain easily

accessible for the event of a dangerous situation, unless it is connected into a terminal box.

 Do not touch the lights if the appliance has been running for some time. Lights heat up during operation

and may cause burns.

 This appliance is designed for fume extraction during standard domestic use. Do not use the appliance

for purposes other than those for which it was designed. Otherwise you expose yourself to the risk of

a dangerous situation and voiding the warranty.

 Follow the instructions for installation and ventilation (with the exception of when a  re stove is used).

 Do not use the  ambé cooking method under the range hood.

 Regularly replace the  lters in the range hood. Otherwise this presents a  re hazard.

 Only use  lters suitable for use with the range hood. The manufacturer or distributor will recommend the

suitable  lter type.

 Do not use the appliance without the aluminium  lter inserted. Do not take out the  lters while the

appliance is on.

 Regularly clean the appliance to prevent a dangerous situation from occurring.

 Before cleaning, replacing  lters, moving or any other maintenance, turn o the appliance and pull out the

power plug from the power socket, or turn o the respective circuit breaker.

 If you are using another gas or natural gas appliance in the room at the same time, the fumes from this

appliance must be spatially isolated.

EN - 3

 If a chimney is connected to the exhaust of the range hood, use pipes with a diameter of 150 or 120 mm.

The pipe connection should be as short as possible.

 Keep packaging materials out of children's reach. They could su er injury or su ocation.

 Children must be supervised to ensure that they do not play with the appliance. If the power cord is

damaged stop using the appliance. Have the power cord replaced at an authorised service centre or by

another quali ed person. Under no circumstances should you replace the power cord yourself.

To ensure safety, use a fuse with a maximum rating of 6 A.

WARNING!

This appliance must not be used by persons (including children) with physical or mental

impairments or by inexperienced persons, unless properly trained or schooled in the safe use of

the appliance, or unless they have been properly supervised by a quali ed person who will be

responsible for their safety.

Attention when transporting or carrying

The packaging materials are from recyclable materials, so dispose of them in an environmentally conscientious

manner according to regulations in force.

During transport adhere to the symbols of the cardboard box.

When carrying the appliance, hold it by the respective handles.

NOTE:

We recommend that you keep the original packaging at least for the duration of the warranty period for

the event of repair or refund and transport to the authorised service centre. Adhere to the symbols on

the cardboard box.

If you do not have the original cardboard box, adhere to the following instructions:

a) Do not place any items on the appliance that could damage the appliance during transport.

b) Protect the appliance against impacts, falls, etc.

c) Wrap the appliance, e.g. in bubble wrap which will protect the appliance from damage.

NOTE:

The carbon  lter is not included.

NOTE:

If the building is equipped with a heat recovery system system, it is necessary to setup the appliance for

internal air circulation (without an exhaust). In that case, it is necessary to purchase the carbon  lter.

EN - 4

PART 2: DESCRIPTION OF THE APPLIANCE

1. Chimney

2. Body of the range hood

3. Control panel

4. Aluminium  lter

5. Lighting

6. Separating plate

1.

2.

3.

4.

5.

6.

Remote control (Optional accessory)

A)

B)

D)

C)

A. Turn the appliance on / o

B. Increase the exhaust power

C. Decrease the exhaust power

D. Turn the lights on / o

EN - 5

PART 3: INSTALLATION

Unpacking

 After unpacking remove all packaging and advertising labels from the appliance.

 Check that the appliance has not been damaged and that the package includes all the items described in

this user's manual.

 If the appliance was damaged during transport, contact authorised service centre.

 Do not use a damaged appliance under any circumstances.

IMPORTANT:

Ensure that children do not play with the packaging material.

Dimensions of the appliance

Supplied accessories (depending on the model)

A non-return exhaust  ap must be installed into the air outlet of the range hood (unless one is already factory

installed).

EN - 6

Placement

Install the range hood at a height of at least 65 cm above an electric cooktop or at a height of 75 cm above

a gas cooktop.

Assembly and installation

Before assembling and installing the appliance carefully read these instructions and adhere to them.

NOTE:

Dowels, screws and the hanging plate are supplied together with the range hood.

IMPORTANT:

Before installing or using the appliance, please  rst read all instructions and check that the voltage and

frequency values on the rating label correspond to the voltage and frequency in your electricity grid.

We recommend that the appliance be connected by a service technician or another quali ed person in

compliance with local codes and regulations.

Before starting the installation

 Check that the purchased appliance has the correct dimensions corresponding to the chosen installation

location. Furthermore ensure that there is an electrical power socket available that will remain accessible

even after the range hood is installed.

 Before installing the range hood, check that all necessary masonry work is complete.

 Have all electrical connections performed by a quali ed person.

 We recommend that you remove the aluminium  lters before installing the range hood.

 Check that there are no packaging materials or other materials, e.g. user's manual, warranty card or bags

with screws, inside the appliance. These need to be taken out and kept for possible use in the future.

 We recommend that you disconnect and move to the side freely standing or built in stoves so that you

have easier access to the rear wall or ceiling. If this is not possible place protective material on to the work

area, cooktop or stove. This will prevent damaging these surfaces.

 Select an even surface for the necessary assembly of the range hood. Cover the surface with a protective

material and place all parts of the range hood and fastening elements on to it.

EN - 7

 It is necessary that a quali ed technician inspects the suitability of the supplied fastening material and

other components for the speci c wall / ceiling type. The wall / ceiling must be su ciently strong to hold

the weight of the range hood.

 Do not attach this range hood to a wall or cabinet furniture by tiling, plastering and do not glue it on using

silicone glue. The appliance is designed to only be installed on a wall / ceiling.

 We recommend that always two people perform the installation of the appliance.

If your range hood is designed to be mounted to the ceiling, adhere to the following instructions.

1. The range hood must only be suspended on ceiling beams or on load bearing ceiling beam connections.

2. Do not suspend the range hood on false ceilings.

3. The ceiling must have a load bearing capacity of at least 40 kg.

4. The ceiling thickness must be at least 30 mm.

IMPORTANT:

THE RANGE HOOD MAY ONLY BE CONNECTED TO THE ELECTRICAL GRID AFTER THE ENTIRE INSTALLATION

IS COMPLETE.

NOTE:

The pictures are only for your reference. These are subject to changes and could be used for more models.

1. Removing the separating plate

To remove the separating plate, pull it down holding the right and left top part.

NOTE:

Check that the distance between the motor unit and a gas stove is at least 84 cm and at least 94 between

the motor unit and an electric stove.

2. Take the motor unit out of the packaging.

3. Measuring distances

Take the screws out of the motor unit (see below) and assemble the location of the motor unit, which

consists of two blocks by sliding in or out.

Then put the screws back.

EN - 8

NOTE:

The part on the appliance marked "FRONT" indicates the position where the control panel will be located.

4. Installation of the hanging plate

Place the motor unit on the ceiling and mark the points for drilling holes for the screws. Into the designated

locations A, B, C, D drill 10mm holes for screws. Depending on the surface of the ceiling use an appropriate

drill bit size.

5. Inserting dowels

Insert dowels into the drilled holes A, B, C, D. Check that the dowels are properly inserted.

6. Inserting screws

Insert screws (5.5 x 45) into the dowels and leave a 5mm gap between the ceiling and the screw head.

7. Attaching the motor unit

Lift the motor unit and slide the screws through the holes in the top part. Check that all screws are in their

respective holes. Turn the motor unit clockwise to secure the motor unit in place.

EN - 9

8. Tightening the screws

Now tighten the screws. Check that all the screws are properly screwed in and that the motor unit is  rmly

secured in place.

9. Installation of the aluminium exhaust tube

Attach one end of the aluminium tube to the range hood  ange and the other end to the air outlet. Check

that both ends are  rmly attached and secured in place.

Exhaust of the aluminium duct tube

Bends and deviations in the aluminium  ue pipe reduce the exhaust performance, so it is essential that the

pipe is bent as little as possible.

Right Wrong

10. Installation of the cover

Place the cover on the motor unit and exhaust and secure in place using the screws supplied.

EN - 10

11. Installation of the body of the range hood

Attach the body of the range hood. Pull the hanging holes over on to the plastic screws and turn the body

clockwise. Tighten the screws.

12. Connect the light holder and switches.

13. Install the aluminium  lters

Lighting connection Key connection

Carbon  lter

If you are using the range hood without an air exhaust, it is necessary to use a carbon  lter. The carbon  lter

is not included. Contact your vendor or an authorised service centre to purchase this  lter.

EN - 11

 Before installing or replacing the carbon  lter, check that the appliance is turned o and disconnected

from the power socket or that the respective circuit breaker is turned o .

 It is necessary to replace the carbon  lter regularly every 3 – 5 months depending on how much the

appliance is used.

 Never wash the carbon  lter in water unless the manufacturer states otherwise.

 Aluminium  lters must always be installed even when the carbon  lter is not installed. Do not use the

appliance without the aluminium  lter installed.

Replacing the carbon  lter

1. For the correct operation of the appliance it is necessary to install a carbon  lter. The number and type

depends on the model.

2. Place the carbon  lter on the motor outlets and turn it in the clockwise direction.

3. To remove the carbon  lter turn it in the anticlockwise direction.

Ventilation

To ensure proper ventilation, leave windows closed while the appliance is turned on.

WARNING!

Pay increased attention if you are using the appliance together with another appliance that uses

air or fuel for its operation (e.g. heating fan, fan, etc.) or that uses gas, coal or wood, as its operation

may negatively a ect the performance of the range hood because it expels air out of the room.

This warning does not apply if you installed the appliance without an exhaust out of the room.

EN - 12

PART 4: OPERATION

Remove the protective foil from the control panel.

Exhaust power selection

This range hood is equipped with 5 levels of exhaust power. Select the power level based on the use of the

stove and the amount steam that the pots emit.

To turn on the motor press the

button and to set the exhaust power level press the or button. Press

the

button to increase the exhaust power and the button to reduce the exhaust power.

Remote control

sensor

Automatic timer (TIMER)

Press and hold the button at the set exhaust power level for at least 2 seconds and the automatic timer

function will be turned on for a period of 15 minutes. When the function is turned on, the respective symbol

will appear on the display and the motor will turn o automatically after 15 minutes.

NOTE:

Use the range hood together with the stove. This will ensure the correct air exhaust. We recommend to

leave the range hood running a few minutes longer than the stove to ensure that all odours are extracted.

Lighting

The range hood is equipped with lighting. Press the button with the light symbol to turn on the lights.

Press the button again to turn the lights o .

NOTE:

If the range hood is equipped with the brightness dimming feature, follow the instructions below.

Changing the brightness of the lights (Dimming)

While the light is on, press and hold down the

button and the brightness will start to change. As soon as

you reach the desired brightness level, release the pressed button. The set brightness will be stored in memory

for future use.

If you press the

button twice in succession, the light will be lit at the maximum brightness level. The light

will always start at the preset brightness level.

Operating tips

1. Regularly clean the aluminium  lters and regularly replace the carbon  lters.

2. Use the medium exhaust power level. Only use the highest power level when necessary.

3. To ensure proper ventilation, leave windows closed while the appliance is turned on.

EN - 13

PART 5: MAINTENANCE AND CLEANING

WARNING!

Before cleaning, regular or other maintenance, installation or removal, check that the appliance

is turned o and disconnected from the power socket or that the respective circuit breaker

is turned o .

Changing a light bulb

 Turn o the appliance.

 Take out the aluminium  lter.

 If the light bulb broke during operation wait until it cools down.

Models with a 50W halogen light bulb

 To remove the halogen light bulb (50 W), press the light bulb holder downwards and gently turn it

anticlockwise. Remove the light bulb.

 Install a light bulb with the same parameters in reverse sequence.

Models with a 20 W light bulb

 To remove the halogen light bulb (20 W),  rst remove the glass cover using a thin screwdriver. Be careful

not to scratch the appliance. Remove a faulty light bulb by pulling downwards and insert a new working

light bulb.

 Use a light bulb with the same parameters.

NOTE:

Do not hold the light bulb with your bare hands. Dirt or sweat from the hand may shorten their lifetime.

EN - 14

Cleaning

 Aluminium  lters capture dust and fat from the extracted air.

 It is necessary to regularly wash these  lters, ideally once a month, depending on the level of use. Wash the

 lters in water with dishwashing detergent, or you may place the  lters in a dishwasher and wash them

using a gentle program (max. 60°C).

 Take out the aluminium  lters by pressing the clip.

 After cleaning allow the aluminium  lters to dry thoroughly before reinstalling them.

 Wipe the outer surface of the range hood with a clean damp wiping cloth lightly dipped in water with

a small amount of dishwashing detergent. Then wipe dry.

 Avoid electrical parts coming into contact with water or another liquid.

Cleaning the aluminium  lters

The aluminium  lters need to be cleaned when "C" appears on the display (depending on the model).

Clean the  lters according to the above mentioned instructions and after reinstalling them press and hold

down the

button for 3 seconds until the "C" symbol (depending on the model) disappears from the display.

The symbol "E" (depending on the model) will appear on the display, which means that the appliance is ready

for operation.

If you wish to use the appliance without clearing the "C" symbol (depending on the model), press the

button to start extraction for 1 second, then the "C" symbol (depending on the model) will appear again and

the motor will continue running.

NOTE:

The "C" symbol (depending on the model) appears on the display after approximately 60 hours

of operation.

WARNING!

For cleaning do not use petrol, benzene, thinners or any other solvents, coarse cleaning agents,

steel wool or any sponges with steel wool.

WARNING!

You may put the aluminium  lters in a dishwasher. The colour of the aluminium  lters may change

after several washes. This is a normal event.

EN - 15

PART 6: BEFORE YOU CALL THE SERVICE CENTRE

If the appliance is not working as it should check the following recommendations for resolving the most

common problems.

If the problem persists or it is not included in the table below, turn o the appliance and disconnect it from the

power socket and contact an authorised service centre.

Problem Solution

The range hood is not working. Check that the power plug is properly inserted in a properly

grounded power socket with the parameters 220 – 240 V ~ 50 Hz.

Check that the motor power switch is in the "On" position.

The lights are not working. Check that the power plug is properly inserted in a properly

grounded power socket with the parameters 220 – 240 V ~ 50 Hz.

Check that the motor power switch is in the "On" position.

Check whether the light bulb or  uorescent tube is broken.

Exhaust power is weak. Check whether the aluminium  lters are dirty.

Check the air outlet, it should be open.

Check whether the carbon  lter is not too dirty.

The range hood does not extract the

air directly out (for models without

an exhaust).

Check whether the aluminium  lters are dirty.

Check whether the carbon  lter is not too dirty.

Attention:

Use the range hood together with the stove. This will ensure the correct air exhaust. We recommend to leave

the range hood running a few minutes longer than the stove to ensure that all odours are extracted.

EN - 16

PART 7: TECHNICAL SPECIFICATIONS

PEW PEI

PEC 6405 -

PEC 9405

PEC 5507 -

PEC 6507

PEB 6408

PEC 5406 -

PEC 6406

PEB 6708

SPEED 1

Voltage (A) 0,5 0,6 0,5 0,5 1 0,6 0,6 0,5

Power (W) 105 90 120 70 135 80 80 110

Air  ow (m³/h) 180 230 200 190 250 190 155 210

Pressure (mmH20) 130 155 170 150 160 160 180 155

Noise level (dB) 36 35 39,7 43 40 45 44 34,5

SPEED 2

Voltage (A) 0,6 0,9 0,6 0,6 1,2 0,9 0,6 0,6

Power (W) 125 120 130 90 170 110 95 125

Air  ow (m³/h) 260 310 265 225 310 400 175 290

Pressure (mmH20) 200 205 230 165 180 190 205 235

Noise level (dB) 43 42 43,6 47,5 48 54 50 43

SPEED 3

Voltage (A) 0,7 1,5 0,7 0,8 1,6 0,9 0,7

Power (W) 145 185 150 110 220 110 150

Air  ow (m³/h) 335 500 360 400 500 400 375

Pressure (mmH20) 265 245 290 180 200 225 285

Noise level (dB) 48 52 49 51,5 55 53 49

SPEED 4

Voltage (A) 0,8 0,8 0,8

Power (W) 170 175 175

Air  ow (m³/h) 450 455 470

Pressure (mmH20) 310 325 320

Noise level (dB) 53 53,4 53,5

SPEED 5

Voltage (A) 11 1

Power (W) 210 210 210

Air  ow (m³/h) 750 750 750

Pressure (mmH20) 350 365 380

Noise level (dB) 61 60,2 61

Input voltage

220 - 240 V

~ 50 Hz

220 - 240 V

~ 50 Hz

220 - 240 V

~ 50 Hz

220 - 240 V

~ 50 Hz

220 - 240 V

~ 50 Hz

220 - 240 V

~ 50 Hz

220 - 240 V

~ 50 Hz

220 - 240 V

~ 50 Hz

Air outlet diameter 150 mm 150 mm 150 mm 120 mm 120 mm 120 mm 120 mm 120 mm

NOTE: All the here mentioned data is subject to change.

EN - 17

INSTRUCTIONS AND INFORMATION REGARDING THE DISPOSAL OF USED

PACKAGING MATERIALS

Dispose of packaging material at a public waste disposal site.

DISPOSAL OF USED ELECTRICAL AND ELECTRONIC APPLIANCES

The meaning of the symbol on the product, its accessory or packaging indicates that this

product shall not be treated as household waste. Please, dispose of this product at your applicable

collection point for the recycling of electrical & electronic equipment waste. Alternatively in some

states of the European Union or other European states you may return your products to your local

retailer when buying an equivalent new product. The correct disposal of this product will help save

valuable natural resources and help in preventing the potential negative impact on the environment

and human health, which could be caused as a result of improper liquidation of waste. Please ask

your local authorities or the nearest waste collection centre for further details. The improper disposal

of this type of waste may fall subject to national regulations for  nes.

For business entities in the European Union

If you wish to dispose of an electrical or electronic device, request the necessary information from

your seller or supplier.

Disposal in other countries outside the European Union

If you wish to dispose of this product, request the necessary information about the correct disposal

method from local government departments or from your seller.

This product meets all the basic EU regulation requirements that relate to it.

Changes to the text, design and technical speci cations may occur without prior notice and we reserve the

right to make these changes.

Stránka sa načítava ...

Philco PEI 4701 Návod na obsluhu

Philco PEI 4701 Návod na obsluhu

V iných jazykoch

Súvisiace články

Ďalšie dokumenty