Hitachi GP 10DL Handling Instructions Manual

Kategória
Elektrické náradie
Typ
Handling Instructions Manual
Cordless Mini Grinder
Akku-Geradschleifer
Μικρος γωνιακος τροχος μπαταριας
Bateryjna szli erka prosta
Akkus mini csíszoló
Akku mini bruska
Akülü mini kalıı taşlama
Mini polizor drept cu acumulator
Akumulatorski mini brusilnik
Аккумуляторная прямая минишлифмашина
Read through carefully and understand these instructions before use.
Diese Anleitung vor Benutzung des Werkzeugs sorgfältig durchlesen und verstehen.
Διαβάστε προσεκτικά και κατανοήσετε αυτές τις οδηγίες πριν τη χρήση.
Przed użytkowaniem należy dokładnie przeczytać niniejszą instrukcję i zrozumieć jej treść.
Használat előtt olvassa el gyelmesen a használati utasítást.
Před použitím si pečlivě přečtěte tento návod a ujistěte se, že mu dobře rozumíte.
Aleti kullanmadan önce bu kılavuzu iyice okuyun ve talimatları anlayın.
Înainte de utilizare, citiţi cu atenţie și înţelegeţi prezentele instrucţiuni.
Pred uporabo natančno preberite in razumite ta navodila.
Внимательно прочтите данную инструкцию по эксплуатации прежде чем пользоваться инструментом.
GP 10DL
Handling instructions
Bedienungsanleitung
Οδηγίες χειρισμού
Instrukcja obsługi
Kezelési utasítás
Návod k obsluze
Kullanım talimatları
Instrucţiuni de utilizare
Navodila za rokovanje
Инструкция по эксплуатации
2
6
7
6
7
8
9
0
!
6
@
$
#
3
1
2
4
5
%
^
&
*
(
)
*
w
q
e
r
!
w
t
y
(a) (b) (c)
12
345
6
78
3
English Deutsch Ελληνικά Polski Magyar
1
Switch dial Wählschalter Διαβάθμιση Regulator Kapcsolótárcsa
2
Low battery warning
lamp
Warnlämpchen
niedriger Akkustand
Λαμπάκι
προειδοποίησης
χαμηλής μπαταρίας
Lampka kontrolna
stanu naładowania
baterii
Alacsony
akkumulátorszint-
jelző lámpa
3
Light Licht Φως ŚwiatłoLámpa
4
Speed Geschwindigkeit Ταχύτητα Prędkość Fordulatszám
5
Switch dial scale Wählschalterskala
Κλίμακα
διαβάθμισης
Skala regulatora
Kapcsolótárcsa
skála
6
10.8 V
Rechargeable
battery
10,8 V au adbare
Batterie
10,8 V
Επαναφορτιζόμενη
μπαταρία
Akumulator 10,8 V
10,8 V-os tölthető
akkumulátor
7
Latch Verriegelung Μάνδαλο Zapadka Retesz
8
Pull out Herausziehen Τραβήξτε έξω Wyciągnij Kihúzni
9
Insert Einsetzen Εισχωρήστε Włóż/wprowadź Bedugni
0
Housing Gehäuse Κιβώτιο Obudowa Ház
!
Push Drücken Σπρώξετε Naciśnij Benyomni
@
Insert Einsetzen Εισχωρήσετε
Włóż/wprowadź Bedugni
#
Pilot lamp Kontrollampe Δοκιμαστική λάμπα Lampka kontrolna Jelzőlámpa
$
Hole for connecting
the rechargeable
battery
Anschluss für
au adbare Batterie
Τρύπα για την
σύνδεση της
επαναφορτιζόμενης
μπαταρίας
Otwór wsuwowy
akumulatora
Nyílás a tölthető
akkumulátor
csatlakoztatásához
%
Screw-type mandrel Schraubstift Κοχλιωτός άξονας Trzpień śrubowy Menetes fúrótengely
^
Flange Flansch Φλάντζα Kołnierz Karima
&
Wheel mandrel Radstift Άξονας τροχού Trzpień tarczowy Kerék fúrótengely
*
Screw in end Einschraubende
Βίδωμα μέχρι
τέλους
Śruba w końcówce Becsavavég
(
Drum mandrel Trommelspindel Άξονας τυμπάνου Trzpień bębnowy Dob fúrótengely
)
Sanding band Schleifband Υαλόχαρτο Taśma szli erska Csiszolószalag
q
Attachment Aufsatz
Προσαρτούμενο
εξάρτημα
Akcesoria Toldalék
w
Collet nut Spannfuttermutter Περικόχλιο
Rowek tulei
zaciskowej
Szorítóhüvely anya
e
Loosen Lockern
Εξάρτημα
χαλάρωσης
Poluzowanie Lazít
r
Lock button Sperrknopf
Διακόπτης
κλειδώματος
Przycisk blokady Rögzítőgomb
t
Collet Spannfutter Στεφάνη Tuleja zaciskowa Szorítóhüvely
y
Shaft screw Wellenschraube Κοχλίας άξονα Śruba wału Tengelycsavar
910
4
Čeština rkçe Română Slovenščina Pyccкий
1
Kruhový spínač Anahtarlığme Disc selector
Številčnica s
stikalom
Циферблатный
переключатель
2
Kontrolní žárovka
slabé baterie
Zayıf pil uyarı
lambası
Avertizare
luminoasă
acumulator aproape
descărcat
Opozorilna lučka za
baterijo pri koncu
Индикаторная
лампочка низкого
уровня заряда
батареи
3
Světlo Lamba Lampă
Luč
Овет
4
Rychlost HızTuraţie Hitrost Скорость
5
Stupnice kruhového
spínače
Anahtarlığme
skalası
Scala discului
selector
Lestvica številčnice
s stikalom
Циферблатная
шкала
переключателя
6
10,8 V Akumulátor
10,8 V Şarj edilebilir
batarya
10,8 V Acumulator
reîncărcabil
10,8 V Baterija, ki
se polni
10,8 В
аккумуляторная
батарея
7
Zámek Mandal Element de blocare Zapah Фиксатор
8
Zatáhnout Çekin TrageţiIzvleciteВытащить
9
Zasunout Yerleştirin IntroduceţiVstavite Вставить
0
Kryt Muhafaza Corp Ohišje Кожух
!
Stisknout İtin ÎmpingeţiPritisnite Нажать
@
Zasunout Yerleştirin IntroduceţiVstavite Вставить
#
Indikátor Kılavuz lamba Lampa pilot Krmilni indikator
Контрольная
лампа
$
Otvor pro zasunutí
akumulátoru
Şarj edilebilir
bataryanın
takılacağı
delik
Ori ciu pentru
conectarea
acumulatorului
reîncărcabil
Luknja za
priključevanje
baterije, ki se polni
Отверстие для
подключения
аккумуляторной
батареи
%
Šroubové vřeteno Vida tipi mandrel Mandrină cu let Trn z navojem
Оправка винтового
типа
^
Příruba Flanş Flanşă Prirobnica Фланец
&
Otáčecí vřeteno Tekerlekli mandrel
Mandrină pentru
disc
Trn v obliki krmila
Оправка колесного
типа
*
Šroub na špičce Vidalama ucu Şurub în cap Konec za privijanje Резьбовой конец
(
Bubnové vřeteno Silindirli mandrel
Mandrină pentru
tambur
Trn v obliki bobna
Барабанная
оправка
)
Pískový brusný pás Zımparalama bandı Bandă de şlefuit Trak za brušenje Наждачный обод
q
Připevně Bağ
lantı Accesoriu Priključek Инструмент
w
Matice kleštiny Bilezik somunu Manşon de prindere Matica z lupino Цанговая гайка
e
Uvolně Gevşetin Slăbire Zrahljati Ослаблять
r
Pojistné tlačítko Kilitleme düğmesi Buton de blocare Gumb za zaporo
Кнопка с
фиксатором
t
Kleštiny Bilezik Inel Lupina Цанга
y
Šroubová hřídel Mil vidası Şurub de ax Vijak z ročajem Винт вала
5
Symbols
WARNING
The following show
symbols used for the
machine. Be sure that you
understand their meaning
before use.
Symbole
WARNUNG
Die folgenden Symbole
werden für diese
Maschine verwendet.
Achten Sie darauf, diese
vor der Verwendung zu
verstehen.
Σύμβολα
ΠΡΟΣΟΧΗ
Τα παρακάτω δείχνουν
τα σύμβολα που
χρησιμοποιούνται στο
μηχάνημα. Βεβαιωθείτε ότι
κατανοείτε τη σημασίας τους
πριν τη χρήση.
Symbole
OSTRZEŻENIE
Następujące oznaczenia
to symbole używane
w instrukcji obsługi
maszyny. Upewnij się, że
rozumiesz ich znaczenie
zanim użyjesz narzędzia.
Jelölések
FIGYELEM
Az alábbiakban a géphez
alkalmazott jelölések
vannak felsorolva. A gép
használata előtt feltétlel
ismerje meg ezeket a
jelöléseket.
Read all safety warnings
and all instructions.
Failure to follow the
warnings and instructions
may result in electric
shock, re and/or serious
injury.
Lesen Sie sämtliche
Sicherheitshinweise
und Anweisungen
durch.
Wenn die Warnungen
und Anweisungen nicht
befolgt werden, kann es
zu Stromschlag, Brand
und/oder ernsthaften
Verletzungen kommen.
Διαβάζετε όλες τις
προειδοποιήσεις
ασφαλείας και όλες τις
οδηγίες.
Η μη τήρηση των
προειδοποιήσεων και
οδηγιών μπορεί να
προκαλέσει
ηλεκτροπληξία,
πυρκαγιά και/ή σοβαρό
τραυματισμό.
Należy dokładnie
zapoznać się
ze wszystkimi
ostrzeżeniami
i wskazówkami
bezpieczeństwa.
Nieprzestrzeganie
ostrzeżeń oraz wskazówek
bezpieczeństwa może
spowodować porażenie
prądem elektrycznym,
pożar i/lub odniesienie
poważnych obrażeń.
Olvasson el
minden biztonsági
gyelmeztetést és
minden utasítást.
A gyelmeztetések
és utasítások be nem
tarsa áramütést, tüzet
és/vagy súlyos sérülést
eredményezhet.
Only for EU countries
Do not dispose of electric
tools together with
household waste material!
In observance of European
Directive 2002/96/EC
on waste electrical and
electronic equipment
and its implementation in
accordance with national
law, electric tools that
have reached the end of
their life must be collected
separately and returned
to an environmentally
compatible recycling facility.
Nur für EU-nder
Werfen Sie
Elektrowerkzeuge nicht in
den Hausmüll!
Gemäss Europäischer
Richtlinie 2002/96/
EG übe
r Elektro- und
Elektronik- Altgeräte
und Umsetzung in
nationales Recht
ssen verbrauchte
Elektrowerkzeuge
getrennt gesammelt und
einer umweltgerechaten
Wiederververtung
zugeführt werden.
Μόνο για τις χώρες της ΕΕ
Μην πετάτε τα ηλεκτρικά
εργαλεία στον κάδο οικιακών
απορριμμάτων!
Σύμφωνα με την
ευρωπαϊκή οδηγία 2002/
96/ΕΚ περί ηλεκτρικών και
ηλεκτρονικών συσκευών
και την ενσωμάτωσή
της στο εθνικό δίκαιο, τα
ηλεκτρικά εργαλεία πρέπει
να συλλέγονται ξεχωριστά
και να επιστρέφονται για
ανακύκλωση με τρόπο φιλικό
προς το περιβάλλον.
Dotyczy tylko państw UE
Nie wyrzucaj
elektronarzędzi wraz z
odpadami z gospodarstwa
domowego!
Zgodnie z Europejską
Dyrektywą 2002/96/WE w
sprawie zużytego sprzętu
elektrotechnicznego i
elektronicznego oraz
dostosowaniem jej
do prawa krajowego,
zużyte elektronarzędzia
należy posegregować
i zutylizować w sposób
przyjazny dla środowiska.
Csak EU-országok
számára
Az elektromos
kéziszerszámokat
ne dobja a háztarsi
szemétbe!
A használt villamos és
elektronikai készülékekről
szóló 2002/96/EK irányelv
és annak a nemzeti jogba
való átültetése szerint az
elhasznált elektromos
kéziszerszámokat
lön kell gyűjteni, és
környezetbarát módon
újra kell hasznosítani.
Symboly
UPOZORNĚ
sledující text obsahuje
symboly, které jsou
použity na zařízení.
Ujistěte se, že rozumíte
jejich obsahu před tím,
než začnete zařízení
používat.
Simgeler
DİKKAT
Aşağıda, bu alet için
kullanılan simgeler
gösterilmiştir. Aleti
kullanmadan önce bu
simgelerin ne anlama
geldiğini anladığınızdan
emin olun.
Simboluri
AVERTISMENT
În cele ce urmează sunt
prezentate simbolurile
folosite pentru mașină.
Înainte de utilizare,
asiguraţi-vă că înţelegeţi
semni caţia acestora.
Simboli
OPOZORILO
V nadaljevanju so
prikazani simboli,
uporabljeni pri stroju. Pred
uporabo se prepričajte, da
jih razumete.
Символы
ПРЕДУПРЕЖДЕНИЕ
Ниже приведены
символы, используемые
для машины. Перед
началом работы
обязательно убедитесь
в том, что Вы понимаете
их значение.
Přečtěte si všechna
varování týkající se
bezpečnosti a všechny
pokyny.
Nedodržení těchto
varování a pokynů může
mít za následek elektrický
šok, požár a/nebo vážné
zranění.
Tüm güvenlik uyarılarını
ve tüm talimatları
okuyun.
Uyarılara ve talimatlara
uyulmaması elektrik
çarpmasına, yangına ve/
veya ciddi yaralanmaya
neden olabilir.
Citiţi toate
avertismentele privind
siguranţa și toate
instrucţiunile.
Nerespectarea
avertismentelor și a
instrucţiunilor poate avea
ca efect producerea de
șocuri electrice, incendii
și/sau vătămări grave.
Preberite vas varnostna
opozorila in navodila.
Z neupoštevanjem
opozoril in navodil tvegate
električni udar, požar in/ali
resne telesne poškodbe.
Прочтите все правила
безопасности и
инструкции.
Не выполнение правил
и инструкций может
привести к поражению
электрическим током,
пожару и/или серьезной
травме.
Jen pro sty EU
Elektrické nářadí
nevyhazujte do komunálního
odpadu!
Podle evropské směrnice
2002/96/EG o nakdání
s použitými elektrickými a
elektronickými zařízeními
a odpovídajících
ustanovení právních
předpisů jednotlivých
zemí se použitá elektric
řadí musí sbírat
odděleně od ostatního
odpadu a podrobit
ekologicky šetrnému
recyklování.
Sadece AB ülkeleri için
Elektrikli el aletlerini
evdeki çöp kutusuna
atmayınız!
Kullanılmış elektrikli
aletleri, elektrik ve
elektronikli eski cihazlar
hakkındaki 2002/96/EC
Avrupa yönergelerine
göre ve bu yönergeler
ulusal hukuk kurallarına
re uyarlanarak, ayrı
olarak toplanmalı ve
çevre şartlarına uygun
bir şekilde tekrar
değerlendirmeye
gönderilmelidir.
Numai pentru ţările membre UE
Nu aruncaţi această sculă
electrică împreună cu deșeurile
menajere!
În conformitate cu Directiva
Europeană 2002/96/CE
referitoare la deșeurile
reprezentând echipamente
electrice și electronice și la
implementarea acesteia în
conformitate cu legislaţiile
naţionale, sculele electrice
care au ajuns la nalul duratei
de folosire trebuie colectate
separat și duse la o unitate de
reciclare compatibilă cu mediul
înconjurător.
Samo za dave EU
Električnih orodij
ne zavržite skupaj z
gospodinjskimi odpadki!
V skladu z evropsko
direktivo 2002/96/EC
o odpadni električni
in elektronski opremi
in izvedbi v skladu z
državnimi zakoni, je treba
električna orodja, ki so
dosegla življenjsko dobo
ločeno zbirati in vrniti
v z okoljem združljivo
ustanovo za recikliranje.
Только для стран ЕС
Не выкидывайте
электроприборы вместе
с обоычным мусором!
В соответствии
с европейской
директивой 2002/96/
ЕС об утилизации
старых электрических и
электронных приборов
и в соответствии с
местными законами
электроприборы, бывщие
в эксплуатации, должны
утилизовываться
отдельно безопасным
для окружающей среды
способом.
6
English
GENERAL POWER TOOL SAFETY WARNINGS
WARNING
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result
in electric shock, re and/or serious injury.
Save all warnings and instructions for future
reference.
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
ammable liquids, gases or dust.
Power tools create sparks which may ignite the
dust or fumes.
c) Keep children and bystanders away while
operating a power tool.
Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way.
Do not use any adapter plugs with earthed
(grounded) power tools.
Unmodi ed plugs and matching outlets will reduce
risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators.
There is an increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions.
Water entering a power tool will increase the risk of
electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts.
Damaged or entangled cords increase the risk of
electric shock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the
risk of electric shock.
f) If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply.
Use of an RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired
or under the in uence of drugs, alcohol or
medication.
A moment of inattention while operating power
tools may result in serious personal injury.
b) Use personal protective equipment. Always
wear eye protection.
Protective equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection used
for appropriate conditions will reduce personal
injuries.
c) Prevent unintentional starting. Ensure the
switch is in the o position before connecting
to power source and/or battery pack, picking
up or carrying the tool.
Carrying power tools with your nger on the switch
or energising power tools that have the switch on
invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on.
A wrench or a key left attached to a rotating part of
the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times.
This enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts.
Loose clothes, jewellery or long hair can be caught
in moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used.
Use of dust collection can reduce dust related
hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application.
The correct power tool will do the job better and
safer at the rate for which it was designed.
b) Do not use the power tool if the switch does
not turn it on and o .
Any power tool that cannot be controlled with the
switch is dangerous and must be repaired.
c) Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools.
Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may a ect the
power tools operation.
If damaged, have the power tool repaired
before use.
Many accidents are caused by poorly maintained
power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed.
Use of the power tool for operations di erent
from those intended could result in a hazardous
situation.
5) Battery tool use and care
a) Recharge only with the charger speci ed by
the manufacturer.
A charger that is suitable for one type of battery
pack may create a risk of re when used with
another battery pack.
(Original instructions)
7
English
b) Use power tools only with speci cally
designated battery packs.
Use of any other battery packs may create a risk of
injury and re.
c) When battery pack is not in use, keep it away
from other metal objects like paper clips,
coins, keys, nails, screws, or other small metal
objects that can make a connection from one
terminal to another.
Shorting the battery terminals together may cause
burns or a re.
d) Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If
contact accidentally occurs, ush with water. If
liquid contacts eyes, additionally seek medical
help.
Liquid ejected from the battery may cause irritation
or burns.
6) Service
a) Have your power tool serviced by a quali ed repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
PRECAUTION
Keep children and in rm persons away.
When not in use, tools should be stored out of reach
of children and in rm persons.
SAFETY WARNINGS COMMON FOR GRINDING,
SANDING, POLISHING OR ABRASIVE
CUTTING-OFF OPERATIONS
a) This power tool is intended to function as a
grinder, sander, polisher or cut-o tool. Read all
safety warnings, instructions, illustrations and
speci cations provided with this power tool.
Failure to follow all instructions listed below may result
in electric shock, re and/or serious injury.
b) Operations such as wire brushing are not
recommended to be performed with this power
tool.
Operations for which the power tool was not designed
may create a hazard and cause personal injury.
c) Do not use accessories which are not speci cally
designed and recommended by the tool
manufacturer.
Just because the accessory can be attached to your
power tool, it does not assure safe operation.
d) The rated speed of the accessory must be at least
equal to the maximum speed marked on the power
tool.
Accessories running faster than their rated speed can
break and y apart.
e) The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool.
Incorrectly sized accessories cannot be adequately
guarded or controlled.
f) The arbour size of wheels, anges, backing pads
or any other accessory must properly t the
spindle of the power tool.
Accessories with arbour holes that do not match the
mounting hardware of the power tool will run out of
balance, vibrate excessively and may cause loss of
control.
g) Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive wheels
for chips and cracks, backing pad for cracks, tear
or excess wear, wire brush for loose or cracked
wires. If power tool or accessory is dropped,
inspect for damage or install an undamaged
accessory. After inspecting and installing an
accessory, position yourself and bystanders away
from the plane of the rotating accessory and run
the power tool at maximum no-load speed for one
minute.
Damaged accessories will normally break apart during
this test time.
h) Wear personal protective equipment. Depending
on application, use face shield, safety goggles or
safety glasses. As appropriate, wear dust mask,
hearing protectors, gloves and workshop apron
capable of stopping small abrasive or workpiece
fragments.
The eye protection must be capable of stopping ying
debris generated by various operations. The dust mask
or respirator must be capable of ltrating particles
generated by your operation.
Prolonged exposure to high intensity noise may cause
hearing loss.
i) Keep bystanders a safe distance away from work
area. Anyone entering the work area must wear
personal protective equipment.
Fragments of workpiece or of a broken accessory may
y away and cause injury beyond immediate area of
operation.
j) Hold power tool by insulated gripping surfaces
only, when performing an operation where the
cutting accessory may contact hidden wiring or
its own cord.
Cutting accessory contacting a “live” wire may make
exposed metal parts of the power tool “live” and shock
the operator.
k) Position the cord clear of the spinning accessory.
If you lose control, the cord may be cut or snagged
and your hand or arm may be pulled into the spinning
accessory.
l) Never lay the power tool down until the accessory
has come to a complete stop.
The spinning accessory may grab the surface and pull
the power tool out of your control.
m) Do not run the power tool while carrying it at your
side.
Accidental contact with the spinning accessory could
snag your clothing, pulling the accessory into your
body.
n) Regularly clean the power tool’s air vents.
The motor’s fan will draw the dust inside the housing
and excessive accumulation of powdered metal may
cause electrical hazards.
o) Do not operate the power tool near ammable
materials.
Sparks could ignite these materials.
p) Do not use accessories that require liquid
coolants.
Using water or other liquid coolants may result in
electrocution or shock.
KICKBACK AND RELATED WARNINGS
Kickback is a sudden reaction to a pinched or snagged
rotating wheel, backing pad, brush or any other accessory.
Pinching or snagging causes rapid stalling of the
rotating accessory which in turn causes the uncontrolled
power tool to be forced in the direction opposite of the
accessory’s rotation at the point of the binding.
For example, if an abrasive wheel is snagged or pinched
by the workpiece, the edge of the wheel that is entering
into the pinch point can dig into the surface of the material
causing the wheel to climb out or kick out. The wheel may
8
English
either jump toward or away from the operator, depending
on direction of the wheel’s movement at the point of
pinching. Abrasive wheels may also break under these
conditions.
Kickback is the result of power tool misuse and/or incorrect
operating procedures or conditions and can be avoided by
taking proper precautions as given below.
a) Maintain a rm grip on the power tool and position
your body and arm to allow you to resist kickback
forces. Always use auxiliary handle, if provided,
for maximum control over kickback or torque
reaction during start-up.
The operator can control torque reactions or kickback
forces, if proper precautions are taken.
b) Never place your hand near the rotating
accessory.
Accessory may kickback over your hand.
c) Do not position your body in the area where power
tool will move if kickback occurs.
Kickback will propel the tool in direction opposite to the
wheel’s movement at the point of snagging.
d) Use special care when working corners, sharp
edges etc. Avoid bouncing and snagging the
accessory.
Corners, sharp edges or bouncing have a tendency to
snag the rotating accessory and cause loss of control
or kickback.
e) Do not attach a saw chain woodcarving blade or
toothed saw blade.
Such blades create frequent kickback and loss of
control.
SAFETY WARNINGS SPECIFIC FOR GRINDING
AND ABRASIVE CUTTING-OFF OPERATIONS
a) Use only wheel types that are recommended for
your power tool and the speci c guard designed
for the selected wheel.
Wheels for which the power tool was not designed
cannot be adequately guarded and are unsafe.
b) Wheels must be used only for recommended
applications. For example: do not grind with the
side of cut-o wheel.
Abrasive cut-o wheels are intended for peripheral
grinding, side forces applied to these wheels may
cause them to shatter.
c) Always use undamaged wheel anges that are of
correct size and shape for your selected wheel.
Proper wheel anges support the wheel thus reducing
the possibility of wheel breakage. Flanges for cut-o
wheels may be di erent from grinding wheel anges.
d) Do not use worn down wheels from larger power
tools.
Wheel intended for larger power tool is not suitable for
the higher speed of a smaller tool and may burst.
ADDITIONAL SAFETY WARNINGS SPECIFIC
FOR ABRASIVE CUTTING-OFF OPERATIONS
a) Do not “jam” the cut-o wheel or apply excessive
pressure. Do not attempt to make an excessive
depth of cut.
Overstressing the wheel increases the loading and
susceptibility to twisting or blinding of the wheel in the
cut and the possibility of kickback or wheel breakage.
b) Do not position your body in line with and behind
the rotating wheel.
When the wheel, at the point of operation, is moving
away from your body, the possible kickback may
propel the spinning wheel and the power tool directly
at you.
c) When wheel is binding or when interrupting a cut
for any reason, switch o the power tool and hold
the power tool motionless until the wheel comes
to a complete stop. Never attempt to remove the
cut-o wheel from the cut while the wheel is in
motion otherwise kickback may occur.
Investigate and take corrective action to eliminate the
cause of wheel binding.
d) Do not restart the cutting operation in the
workpiece. Let the wheel reach full speed and
carefully reenter the cut.
The wheel may bind, walk up or kickback if the power
tool is restarted in the workpiece.
GENERAL SAFETY INSTRUCTIONS FOR
CORDLESS MINI GRINDERS
Check that speed marked on the wheel is equal to or
greater than the rated speed of the grinder;
Ensure that the wheel dimensions are compatible with
the grinder;
Abrasive wheels shall be stored and handled with care
in accordance with manufacturer’s instructions;
– Inspect the grinding wheel before use, do not use
chipped, cracked or otherwise defective products;
Ensure that mounted wheels and points are tted in
accordance with the manufacturer’s instructions;
Ensure that blotters are used when they are provided
with the bonded abrasive product and when they are
required;
Do not use the power tool to machine materials that
contain components that are harmful to health.
Use the designated accessory or attachment.
Ensure that the abrasive product is correctly mounted
and tightened before use and run the tool at no-
load for 30 s in a safe position, stop immediately if
there is considerable vibration or if other defects are
detected. If this condition occurs, check the machine
to determine the cause;
If a guard is equipped with the tool never use the tool
without such a guard;
Do not use separate reducing bushings or adapters to
adapt large hole abrasive wheels;
For tools intended to be tted with threaded hole
wheel, ensure that the thread in the wheel is long
enough to accept the spindle length;
Check that the work piece is properly supported;
Do not use cutting o wheel for side grinding;
Ensure that sparks resulting from use do not create
a hazard e.g. do not hit persons, or ignite ammable
substances;
Ensure that ventilation openings are kept clear when
working in dusty conditions, if it should become
necessary to clear dust, rst disconnect the tool from
the mains supply (use non metallic objects) and avoid
damaging internal parts;
Always use eye and ear protection. Other personal
protective equipment such as dust mask, gloves,
helmet and apron should be worn;
Pay attention to the wheel that continues to rotate after
the tool is switched o .
– Always charge the battery at a temperature of 0 –
40°C.
A temperature of less than 0°C will result in over
charging which is dangerous. The battery cannot be
charged at a temperature greater than 40°C.
The most suitable temperature for charging is that of
20 – 25°C.
Do not use the charger continuously.
When one charging is completed, leave the charger for
about 15 minutes before the next charging of battery.
9
English
Do not allow foreign matter to enter the hole for
connecting the rechargeable battery.
Never disassemble the rechargeable battery and
charger.
Never short-circuit the rechargeable battery.
Short-circuiting the battery will cause a great electric
current and overheat. It results in burn or damage to
the battery.
Do not dispose of the battery in re.
If the battery burnt, it may explode.
When drilling in wall, oor or ceiling, check for buried
electric power cord, etc.
Do not insert object into the air ventilation slots of the
charger.
Inserting metal objects or in ammables into the
charger air ventilation slots will result in electrical
shock hazard or damaged charger.
Bring the battery to the shop from which it was
purchased as soon as the post-charging battery life
becomes too short for practical use. Do not dispose of
the exhausted battery.
Using an exhausted battery will damage the charger.
CAUTION ON LITHIUM-ION BATTERY
To extend the lifetime, the lithium-ion battery equips with
the protection function to stop the output.
In the cases of 1 to 3 described below, when using this
product, even if you are pulling the switch, the motor may
stop. This is not the trouble but the result of protection
function.
1. When the battery power remaining runs out, the motor
stops.
In such case, charge it up immediately.
2. If the tool is overloaded, the motor may stop. In this
case, release the switch of tool and eliminate causes
of overloading. After that, you can use it again.
3. If the battery is overheated under overload work, the
battery power may stop.
In this case, stop using the battery and let the battery
cool. After that, you can use it again.
Furthermore, please heed the following warning and
caution.
WARNING
In order to prevent any battery leakage, heat generation,
smoke emission, explosion and ignition beforehand,
please be sure to heed the following precautions.
1. Make sure that swarf and dust do not collect on the
battery.
During work make sure that swarf and dust do not fall
on the battery.
Make sure that any swarf and dust falling on the power
tool during work do not collect on the battery.
Do not store an unused battery in a location exposed
to swarf and dust.
Before storing a battery, remove any swarf and dust
that may adhere to it and do not store it together with
metal parts (screws, nails, etc.).
2. Do not pierce battery with a sharp object such as a
nail, strike with a hammer, step on, throw or subject the
battery to severe physical shock.
3. Do not use an apparently damaged or deformed
battery.
4. Do not use the battery in reverse polarity.
5. Do not connect directly to an electrical outlets or car
cigarette lighter sockets.
6. Do not use the battery for a purpose other than those
speci ed.
7. If the battery charging fails to complete even when a
speci ed recharging time has elapsed, immediately
stop further recharging.
8. Do not put or subject the battery to high temperatures
or high pressure such as into a microwave oven, dryer,
or high pressure container.
9. Keep away from re immediately when leakage or foul
odor are detected.
10. Do not use in a location where strong static electricity
generates.
11. If there is battery leakage, foul odor, heat generated,
discolored or deformed, or in any way appears
abnormal during use, recharging or storage,
immediately remove it from the equipment or battery
charger, and stop use.
CAUTION
1. If liquid leaking from the battery gets into your eyes,
do not rub your eyes and wash them well with fresh
clean water such as tap water and contact a doctor
immediately.
If left untreated, the liquid may cause eye-problems.
2. If liquid leaks onto your skin or clothes, wash well with
clean water such as tap water immediately.
There is a possibility that this can cause skin irritation.
3. If you nd rust, foul odor, overheating, discolor,
deformation, and/or other irregularities when using the
battery for the rst time, do not use and return it to your
supplier or vendor.
WARNING
If an electrically conductive foreign object enters the
terminals of the lithium ion battery, a short-circuit may
occur resulting in the risk of re. Please observe the
following matters when storing the battery.
Do not place electrically conductive cuttings,
nails, steel wire, copper wire or other wire in the
storage case.
SPECIFICATIONS
POWER TOOL
No-load speed 5000 – 35000 min
–1
Rated speed 34000 min
–1
Collet chuck capacity 3.2 mm
Rechargeable battery BCL1015: Li-ion 10.8 V (1.5 Ah 3 cells)
Weight 0.48 kg
CHARGER
Model UC10SL2 UC10SFL
Charging voltage 10.8 V 10.8 V
Weight 0.35 kg 0.35 kg
10
English
STANDARD ACCESSORIES
GP10DL
(LCSK)
1 Accessories × 40 pcs ....................... 1
2 Battery (BCL1015) ............................ 1
3 Charger (UC10SL2 or UC10SFL) ..... 1
4 Plastic case ...................................... 1
GP10DL
(NN)
1 Accessories × 40 pcs ....................... 1
Use for wood
engraving and
grinding.
Use to machine hard
materials such as
glass and ceramics.
Use to engrave,
grind and make
grooves in wood,
plastic and soft
metals (aluminium,
copper, brass).
Use to make holes in
wood and plywood.
Use to slice or cut
materials.
Suitable for cutting thin
rods and pipes.
Recuts crushed
grooves in screw heads.
Do not press hard
against workpiece as it
may crack.
Use to polish hard
materials such as
stainless steel.
Suitable for nal
polishing after rough
grinding.
Use to give smooth
nish to metal
surfaces.
Use for mirror
polishing of jewelry
and metals.
Choose the size to
suit the workpiece.
Suitable for tasks such
as shaping wood and
nishing models.
Grind in two stages
with di erent grit
numbers to achieve a
good surface nish.
Aluminium oxide point [φ15.9 mm × 1]
15.9 mm
Silicon carbide point [φ4.8 mm × 1]
4.8 mm
High-speed cutter [φ3.2 mm × 1]
3.2 mm
Drill [φ3.2 mm × 1]
3.2 mm
Felt polishing wheel [φ12.7 mm × 4]
12.7 mm
Felt polishing wheel [φ25.4 mm × 2]
25.4 mm
Sanding band [φ12.7 mm/60-grit × 6]
12.7 mm
60-grit
Sanding band [φ12.7 mm/120-grit × 2]
12.7 mm
120-grit
Cutting wheel [φ23.8 × t0.6 × 6]
23.8 mm
0.6 mm
Cutting wheel [φ23.8 × t1.0 × 2]
23.8 mm
1.0 mm
Aluminium oxide grinding wheel [φ22.2 × 1]
22.2 mm
Sanding disc [φ19.1 mm/180-grit × 10]
19.1 mm
180-grit
Polishing wheel [φ25.4 mm × 2]
25.4 mm
Collet spanner (for loosening
tight collet nuts)
Wheel mandrel
[φ3.2 mm × 1]
Screw-type mandrel
[φ3.2 mm × 1]
Drum mandrel
[φ3.2 mm × 1]
<Uses>
[Accessory]
For details of the attachments, refer to “Provided
attachments”.
Standard accessories are subject to change without
notice.
Provided attachments
CAUTION
Standard attachments are exclusively for
use with the GP10DL. Do not use with other
equipment such as electric drills, etc. Doing so
may result in injury or damage to the tip tool.
11
English
OPTIONAL ACCESSORIES (sold separately)
1. Battery (BCL1015)
Optional accessories are subject to change without notice.
APPLICATIONS
Making wood carved handicrafts and precious metal
ornaments
Engraving and sculpting glass and ceramics
Grinding and polishing steel and stone
BASIC FUNCTIONS
1. Low battery warning lamp (Fig. 1)
To check the remaining battery power, operate the
grinder unloaded.
If the remaining battery power is low, the warning lamp
(red LED) will light. If the lamp lights, charge the battery
without delay.
NOTE
The low battery warning lamp may be a ected by the
ambient temperature or battery characteristics. Use
the lamp as a guide for when to charge the battery.
The low battery warning lamp may light during
operation of the grinder. This is due to a temporary
drop in the battery voltage, and not to low battery
power.
When checking the remaining battery power, be sure
to operate the grinder in an unloaded condition.
2. Switch dial
The switch dial also serves as the start-up switch and
the speed dial. When the dial is rotated from [0] to a
higher number, the grinder switches on and gradually
builds up speed. At the same time, the LED lamp lights
and illuminates the tip of the grinder.
When the dial is returned to [0], the grinder switches o
and rotation stops.
For safety reasons, the grinder will not start up if the
battery is inserted while the switch is at any position
other than [0].
To switch the grinder on at such time, return the dial to
[0] and then rotate it to a higher number.
The approximate relationship between the numbers on
the switch dial and the rotation speed is shown in the
graph in Fig. 2.
BATTERY REMOVAL/INSTALLATION
1. Battery removal
Hold the handle tightly and push the battery latch to
remove the battery (see Figs. 3 and 4).
CAUTION
Never short-circuit the battery.
2. Battery installation
Insert the battery while observing its polarities (see
Fig. 4).
CHARGING
Before using the power tool, charge the battery as follows.
1. Connect the charger’s power cord to the
receptacle.
When connecting the plug of the charger to a
receptacle, the pilot lamp will blink in red (At 1-second
intervals).
2. Insert the battery into the charger.
Firmly insert the battery into the charger till it contacts
the bottom of the charger as shown in Fig. 5.
3. Charging
When inserting a battery in the charger, the pilot lamp
will light up continuously in red.
When the battery becomes fully recharged, the pilot
lamp will blink in red (At 1-second intervals). (See
Table 1)
(1) Pilot lamp indication
The indications of the pilot lamp will be as shown in
Table 1, according to the condition of the charger or
the rechargeable battery.
Table 1
Indications of the pilot lamp
Pilot lamp
(red)
Before
charging
Blinks
Lights for 0.5 seconds. Does not light for 0.5
seconds. (o for 0.5 seconds)
While
charging
Lights
Lights continuously
Charging
complete
Blinks
Lights for 0.5 seconds. Does not light for 0.5
seconds. (o for 0.5 seconds)
Overheat
standby
Blinks
Lights for 1 second. Does not light for 0.5
seconds. (o for 0.5 seconds)
Battery overheated.
Unable to charge.
(Charging will commence
when battery cools)
Charging
impossible
Flickers
Lights for 0.1 second. Does not light for 0.1
seconds. (o for 0.1 seconds)
Malfunction in the
battery or the charger
12
English
(2) Regarding the temperatures of the rechargeable
battery
The temperatures for rechargeable batteries are
as shown in the Table 2, and batteries that have
become hot should be cooled for a while before being
recharged.
Table 2 Recharging ranges of batteries
Rechargeable batteries
Temperatures at which the
battery can be recharged
BCL1015 0°C – 50°C
(3) Regarding recharging time
Depending on the combination of the charger and
batteries, the charging time will become as shown in
Table 3.
Table 3 Charging time (At 20°C) ( ): cells
Charger
Battery
UC10SL2 UC10SFL
1,5 Ah (3) Approx. 30 min. Approx. 40 min.
NOTE
The recharging time may vary according to the
ambient temperature.
4. Disconnect the charger’s power cord from the
receptacle.
5. Hold the charger rmly and pull out the battery.
NOTE
Be sure to pull out the battery from the charger after
use, and then keep it.
CAUTION
If the battery is charged while it is heated because it
has been left for a long time in a location subject to
direct sunlight or because the battery has just been
used, the pilot lamp of the charger lights for 1 second,
does not light for 0.5 seconds (o for 0.5 seconds).
In such a case, rst let the battery cool, then start
charging.
When the pilot lamp ickers (at 0.2-second intervals),
check for and take out any foreign objects in the
charger’s battery connector. If there are no foreign
objects, it is probable that the battery or charger is
malfunctioning. Take it to your authorized Service
Center.
Since the built-in micro computer takes about
3 seconds to con rm that the battery being charged
with chargers are taken out, wait for a minimum of
3 seconds before reinserting it to continue charging. If
the battery is reinserted within 3 seconds, the battery
may not be properly charged.
PRIOR TO OPERATION
1. Setting up and checking the work environment
Check if the work environment is suitable by the above
precautions.
HOW TO ATTACH THE TIP TOOL
WARNING
To prevent accidents, be sure to switch the power o
and remove the battery from the grinder.
CAUTION
Make sure the mandrel is screwed in tightly.
After attaching the tip tool, check that the tool is
securely xed.
If the tool is loose, it may come o , causing damage or
injury.
1. How to use the screw-type mandrel (Fig. 6 (a))
Use the screw-type mandrel when using the felt
polishing wheel.
Keeping the wheel straight, screw it onto the thread of
the screw-type mandrel as far as the ange.
2. How to use the wheel mandrel (Fig. 6 (b))
Remove the screw in the end of the mandrel with a
athead screwdriver and attach the cutting wheel or
sanding disc.
3. How to use the drum mandrel (Fig. 6 (c))
A 60-grit sanding band is tted to the drum mandrel
when it leaves the factory.
Loosen the screw in the end of the mandrel with a
screwdriver to remove/attach the sanding band.
After attaching the sanding band, tighten the screw
securely.
4. Attach the tip tool to the grinder
Rotate the collet nut by hand while pressing the lock
button to further depress the lock button.
In this state, the shaft is locked and the collet nut can
be loosened or tightened. (Fig. 7)
To attach the tip tool, insert the tip tool as far as it will
go and tighten the collet nut securely.
To detach the tip tool, the collet nut can usually be
rotated by hand, though occasionally it may be tight.
If the collet nut is tight, use the provided collet spanner
to loosen it.
Iron powder on the collet nut, collet or shaft screw may
cause the collet nut to be di cult to rotate. (Fig. 8)
Be sure to remove any powder before attaching or
detaching the tip tool.
NOTE
Very occasionally, the tip tool may be di cult to detach
from the collet.
If this happens, with the collet nut loosened, press the
end of the tool lightly against a hard object. (Fig. 10)
5. Balance adjustment of the tip tool
After attaching the tip tool, operate the grinder at low
speed. If the balance is not right, follow the procedure
below to adjust the balance.
Loosen the collet nut while pressing the lock button.
Next, rotate the tip tool by 1/4 and tighten the collet nut.
Operate the grinder at low speed and check the
balance. If the balance is right, adjustment is
completed.
If the balance still is not right, detach the tip tool, the
collet nut and collet and re-attach them. If the tip tool
is still not balanced after several such attempts, check
for deformation or wear of the tip tool or deformation of
the collet. If worn or deformed, replace the tip tool or
collet.
13
English
OPERATING THE GRINDER
WARNING
Keep your face away from the tip tool during use.
Wear goggles and a dust mask when using the grinder.
Breakage of the tip tool may lead to injury.
Do not operate the grinder at extremely slow speed. A
smooth nished surface will not be achieved and doing
so may lead to damage of the tip tool, breakdown of
the grinder or injury.
CAUTION
Do not touch the tip tool, collet nut or collet
immediately after machining as they will be very hot
and touching them may result in burns.
1. Remove the battery and attach the tip tool
2. Fix the workpiece so that it does not move
The smaller the workpiece, the more unstable it is to
machine. Fix small workpieces in a vise.
Holding the workpiece by hand may result in injury.
3. Insert the battery in the grinder
4. Check the balance of the tip tool
Check the tip tool visually at low speed (around [1] on
the switch dial).
Also check for abnormal noise during operation.
5. Select the machining speed
Select the optimal speed for the material while
performing trial grinding with reference to Table 4.
If plastic is machined at high speed, it may melt due to
heating. Test it gradually starting from a low speed.
Table 4 Switch dial settings
Workpiece
material
Tip tool
Softwood
Hardwood
Laminate/
Plastic
Steel
Aluminium,
brass, etc.
Shell/
Stone
Ceramic Glass
Aluminium oxide
point
3-4 3-4 2.5 1 1.5 3-4
Silicon carbide point 1.5 3-4 1 1.5 3-4 3-4
High-speed cutter 3-4 3-4 1 1.5 3-4
Drill 3-4 3-4 1 1.5
Cutting wheel 1 3-4 3-4 3-4 3-4
Aluminium oxide
grinding wheel
3-4 3-4 2.5 1 1.5 3-4
Sanding disc 2.5 2.5 1 1
Polishing wheel 1 1 1 1 1
Felt polishing wheel 1 1
Sanding band 1-4 1-4 1-4 3-4 3-4 1-4 1-4
6. Machining
Place the rotating tip tool lightly against the workpiece
and machine the workpiece with minimal pressure.
Rather than doing the whole task in a single action,
a better nish is achieved gradually by multiple
machinings.
NOTE
The grinder narrows toward the tip tool holder. Place
your nger on the narrow section and hold the grinder
for easy operation. (Fig. 9)
When machining a material for the rst time or using
the tip tool for the rst time, perform trial grinding rst
to check the optimal speed, how to hold the grinder
and how to place the tool against the workpiece.
If you do not achieve the expected results, applying
more pressure to the power tool will not give better
results. Nor will the machining performance be
improved by tilting the power tool. Adjust the rotating
speed or change to another tip tool.
MAINTENANCE AND INSPECTION
1. Inspecting the accessories
Using a tip tool or mandrel with a worn or damaged
end will not only result in a poor nish, but will place
unreasonable strain on the motor, causing reduced
e ciency, damage or injury.
If the tip tool or mandrel is worn or damaged, replace it.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws
be loose, retighten them immediately. Failure to do so
could result in serious hazard.
3. Maintenance of the motor
The motor unit winding is the very “heart” of the power
tool.
Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
4. Cleaning of the outside
When the grinder is stained, wipe with a soft dry cloth
or a cloth moistened with soapy water. Do not use
chloric solvents, gasoline or paint thinner, for they melt
plastics.
5. Storage
Store the grinder in a place in which the temperature is
less than 4C and out of reach of children.
NOTE
Make sure that the battery is fully charged when stored
for a long period (3 months or more). The battery with
smaller capacity may not be able to be charged when
used, if stored for a long period.
NOTE
Storing Lithium-ion Batteries
Make sure the lithium-ion batteries have been fully
charged before storing them.
14
English
Prolonged storage of batteries with a low charge
may result in performance deterioration, signi cantly
reducing battery usage time or rendering the batteries
incapable of holding a charge.
However, signi cantly reduced battery usage time may
be recovered by repeatedly charging and using the
batteries two to ve times.
If the battery usage time is extremely short despite
repeated charging and use, consider the batteries
dead and purchase new batteries.
6. Service parts list
CAUTION
Repair, modi cation and inspection of Hitachi Power
Tools must be carried out by a Hitachi Authorized
Service Center.
This Parts List will be helpful if presented with the
tool to the Hitachi Authorized Service Center when
requesting repair or other maintenance.
In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
country must be observed.
MODIFICATIONS
Hitachi Power Tools are constantly being improved
and modi ed to incorporate the latest technological
advancements.
Accordingly, some parts may be changed without prior
notice.
Important notice on the batteries for the Hitachi
cordless power tools
Please always use one of our designated genuine
batteries. We cannot guarantee the safety and
performance of our cordless power tool when used
with batteries other than these designated by us, or
when the battery is disassembled and modi ed (such
as disassembly and replacement of cells or other
internal parts).
GUARANTEE
We guarantee Hitachi Power Tools in accordance with
statutory/country speci c regulation. This guarantee does
not cover defects or damage due to misuse, abuse, or
normal wear and tear. In case of complaint, please send
the Power Tool, undismantled, with the GUARANTEE
CERTIFICATE found at the end of this Handling instruction,
to a Hitachi Authorized Service Center.
NOTE
Due to HITACHI’s continuing program of research and
development, the speci cations herein are subject to
change without prior notice.
Information concerning airborne noise and vibration
The measured values were determined according to
EN60745 and declared in accordance with ISO 4871.
Measured A-weighted sound power level: 73 dB (A)
Measured A-weighted sound pressure level: 62 dB (A)
Uncertainty KpA: 3 dB (A).
Wear hearing protection.
Vibration total values (triax vector sum) determined
according to EN60745.
Surface grinding:
Vibration emission value а
h, SG
= 2.2 m/s
2
Uncertainty K = 1.5 m/s
2
The declared vibration total value has been measured in
accordance with a standard test method and may be used
for comparing one tool with another.
It may also be used in a preliminary assessment of
exposure.
WARNING
The vibration emission during actual use of the power
tool can di er from the declared total value depending
on the ways in which the tool is used.
To identify safety measures to protect the operator
that are based on an estimation of exposure in the
actual conditions of use (taking account of all parts of
the operating cycle such as the times when the tool is
switched o and when it is running idle in addition to
the trigger time).
ALLGEMEINE SICHERHEITSHINWEISE FÜR
ELEKTROGERÄTE
WARNUNG
Lesen Sie sämtliche Sicherheitshinweise und
Anweisungen durch
Wenn die Warnungen und Anweisungen nicht befolgt
werden, kann es zu Stromschlag, Brand und/oder
ernsthaften Verletzungen kommen.
Bitte bewahren Sie alle Warnhinweise und
Anweisungen zum späteren Nachschlagen auf.
Der Begri Elektrowerkzeug“ bezieht sich in den
Warnhinweisen auf Elektrowerkzeuge mit Netz-
(schnurgebunden) oder Akkubetrieb (schnurlos).
1) Sicherheit im Arbeitsbereich
a) Sorgen Sie für einen sauberen und gut
ausgeleuchteten Arbeitsbereich.
Zugestellte oder dunkle Bereiche ziehen Unfälle
förmlich an.
b) Verwenden Sie Elektrowerkzeuge niemals
an Orten, an denen Explosionsgefahr
besteht – zum Beispiel in der Nähe von leicht
ent ammbaren Flüssigkeiten, Gasen oder
Stäuben.
Bei der Arbeit mit Elektrowerkzeugen kann es zu
Funkenbildung kommen, wodurch sich Stäube
oder Dämpfe entzünden können.
c) Sorgen Sie bei der Arbeit mit
Elektrowerkzeugen dafür, dass sich keine
Zuschauer (insbesondere Kinder) in der Nähe
be nden.
Wenn Sie abgelenkt werden, können Sie die
Kontrolle über das Werkzeug verlieren.
2) Elektrische Sicherheit
a) Elektrowerkzeuge müssen mit passender
Stromversorgung betrieben werden.
Nehmen Sie niemals irgendwelche
Änderungen am Anschlussstecker vor.
Verwenden Sie bei Elektrowerkzeugen
mit Schutzkontakt (geerdet) niemals
Adapterstecker.
Stecker im Originalzustand und passende
Steckdosen reduzieren das Stromschlagrisiko.
b) Vermeiden Sie Körperkontakt mit geerdeten
Gegenständen wie Rohrleitungen, Heizungen,
Herden oder Kühlschränken.
Bei Körperkontakt mit geerdeten Gegenständen
besteht ein erhöhtes Stromschlagrisiko.
c) Setzen Sie Elektrowerkzeuge niemals Regen
oder sonstiger Feuchtigkeit aus.
Wenn Flüssigkeiten in ein Elektrowerkzeug
eindringen, erhöht sich das Stromschlagrisiko.
d) Verwenden Sie die Anschlussschnur
nicht missbräuchlich. Tragen Sie
das Elektrowerkzeug niemals an der
Anschlussschnur, ziehen Sie es nicht damit
heran und ziehen Sie den Stecker nicht an der
Anschlussschnur aus der Steckdose.
Halten Sie die Anschlussschnur von
Hitzequellen, Öl, scharfen Kanten und
beweglichen Teilen fern.
Bescdigte oder verdrehte Anschlussschnüre
erhöhen das Stromschlagrisiko.
e) Wenn Sie ein Elektrowerkzeug im Freien
benutzen, verwenden Sie ein für den
Außeneinsatz geeignetes Verlängerungskabel.
Ein für den Außeneinsatz geeignetes Kabel
vermindert das Stromschlagrisiko.
f) Falls sich der Betrieb des Elektrowerkzeuges
in feuchter Umgebung nicht vermeiden lässt,
verwenden Sie eine Stromversorgung mit
Fehlerstromschutzeinrichtung (Residual
Current Device, RCD).
Durch den Einsatz einer
Fehlerstromschutzeinrichtung wird das Risiko
eines elektrischen Schlages reduziert.
3) Persönliche Sicherheit
a) Bleiben Sie wachsam, achten Sie auf das, was
Sie tun, und setzen Sie Ihren Verstand ein,
wenn Sie mit Elektrowerkzeugen arbeiten.
Benutzen Sie keine Elektrowerkzeuge, wenn
Sie müde sind oder unter Ein uss von Drogen,
Alkohol oder Medikamenten stehen.
Bei der Arbeit mit Elektrowerkzeugen können
bereits kurze Phasen der Unaufmerksamkeit zu
schweren Verletzungen führen.
b) Benutzen Sie eine persönliche
Schutzausrüstung. Tragen Sie immer einen
Augenschutz.
Schutzausstung wie Staubmaske, rutschsichere
Sicherheitsschuhe, Schutzhelm und Gehörschutz
senken das Verletzungsrisiko bei angemessenem
Einsatz.
c) Vermeiden Sie unbeabsichtigten Anlauf.
Achten Sie darauf, dass sich der Schalter
in der Aus- (O -) Position be ndet, ehe Sie
das Get mit der Stromversorgung und/
oder Batteriestromversorgung verbinden, es
aufheben oder herumtragen.
Das Herumtragen von Elektrowerkzeugen mit
dem Finger am Schalter oder das Herstellen der
Stromversorgung bei betätigtem Schalter zieht
Unfälle regelrecht an.
d) Entfernen Sie sämtliche Einstellwerkzeuge
(Einstellschlüssel), ehe Sie das
Elektrowerkzeug einschalten.
Ein an einem beweglichen Teil des
Elektrowerkzeugs angebrachter Schlüssel kann zu
Verletzungen führen.
e) Sorgen Sie für einen festen Stand. Achten Sie
jederzeit darauf, sicher zu stehen und das
Gleichgewicht zu bewahren.
Dadurch haben Sie das Elektrowerkzeug in
unerwarteten Situationen besser im Gri .
f) Kleiden Sie sich richtig. Tragen Sie keine lose
Kleidung oder Schmuck. Halten Sie Haar,
Kleidung und Handschuhe von beweglichen
Teilen fern.
Lose Kleidung, Schmuck oder langes Haar kann
von beweglichen Teilen erfasst werden.
g) Wenn Anschlüsse für Staubabsaug- und
-sammelvorrichtungen vorhanden sind, sorgen
Sie dafür, dass diese richtig angeschlossen
und eingesetzt werden.
Durch Entfernen des Staubes können
staubbezogene Gefahren vermindert werden.
4) Einsatz und P ege von Elektrowerkzeugen
a) Überanspruchen Sie Elektrowerkzeuge nicht.
Benutzen Sie das richtige Elektrowerkzeug für
Ihren Einsatzzweck.
Das richtige Elektrowerkzeug erledigt seine Arbeit
bei bestimmungsgemäßem Einsatz besser und
sicherer.
b) Benutzen Sie das Elektrowerkzeug nicht, wenn
es sich nicht am Schalter ein- und ausschalten
lässt.
(Übersetzung der ursprünglichen Anleitung)
Deutsch
15
Jedes Elektrowerkzeug, das nicht mit dem Schalter
betätigt werden kann, stellt eine Gefahr dar und
muss repariert werden.
c) Stecken Sie den Stecker der Stromversorgung
oder Batteriestromversorgung vom Gerät
ab, ehe Sie Einstellarbeiten vornehmen,
Zubehörteile tauschen oder das
Elektrowerkzeug verstauen.
Solche präventiven Sicherheitsmaßnahmen
verhindern den unbeabsichtigten Anlauf des
Elektrowerkzeugs und die damit verbundenen
Gefahren.
d) Lagern Sie nicht benutzte Elektrowerkzeuge
außerhalb der Reichweite von Kindern,
lassen Sie nicht zu, dass Personen das
Elektrowerkzeug bedienen, die nicht mit
dem Werkzeug selbst und/oder diesen
Anweisungen vertraut sind.
Elektrowerkzeuge in ungeschulten Händen sind
gefährlich.
e) Halten Sie Elektrowerkzeuge in Stand. Prüfen
Sie auf Fehlausrichtungen, sicheren Halt
und Leichtgängigkeit beweglicher Teile,
Bescdigungen von Teilen und auf jegliche
andere Zustände, die sich auf den Betrieb des
Elektrowerkzeugs auswirken können.
Bei Bescdigungen lassen Sie das
Elektrowerkzeug reparieren, ehe Sie es
benutzen.
Viele Unfälle mit Elektrowerkzeugen sind auf
schlechte Wartung zurückzuführen.
f) Halten Sie Schneidwerkzeuge scharf und
sauber.
Richtig gewartete Schneidwerkzeuge mit scharfen
Schneidkanten bleiben weniger häu g hängen und
sind einfacher zu beherrschen.
g) Benutzen Sie Elektrowerkzeuge, Zubehör,
Werkzeugspitzen und Ähnliches in
Übereinstimmung mit diesen Anweisungen
– beachten Sie dabei die jeweiligen
Arbeitsbedingungen und die Art und Weise
der auszuführenden Arbeiten.
Der Gebrauch des Elektrowerkzeuges für andere
als die vorgesehenen Anwendungen kann zu
gefährlichen Situationen führen.
5) Verwendung und P ege der Batterie
a) Laden Sie das Gerät nur mit dem vom
Hersteller empfohlenen Ladeget auf.
Ein Ladegerät für einen speziellen Batterietyp kann
bei Verwendung mit anderen Batterien zu Gefahren
führen.
b) Verwenden Sie für das Get nur die speziell
empfohlenen Batterien.
Eine Verwendung von anderen Batterien kann zu
Verletzungen und Bränden führen.
c) Ist die Batterie nicht in Gebrauch, achten
Sie darauf, dass sie nicht mit metallischen
Gegenständen, beispielsweise Büroklammern,
nzen, Schssel, Nägel, Schrauben in
Kontakt kommt, da diese Gegenstände einen
Kurzschluss der Anschsse verursachen
könnten.
Ein Kurzschluss der Batterieanschsse kann zu
Verbrennungen oder Bränden führen.
d) Im Falle von Srungen, kann Flüssigkeit
aus der Batterie austreten. Vermeiden Sie
in diesem Fall jeglichen Kontakt. Sollten
Sie dennoch mit der Batterie in Berührung
kommen, waschen Sie die betro ene Stelle
gründlich mit Wasser ab. Ist die Flüssigkeit ins
Auge geraten, suchen Sie einen Arzt auf.
Ausgetretene Batterie üssigkeiten können zu
Reizungen oder Verbrennungen führen.
6) Service
a) Lassen Sie Elektrowerkzeuge durch
quali zierte Fachkräfte und unter Einsatz
passender, zugelassener Originalteile warten.
Dies sorgt dafür, dass die Sicherheit des
Elektrowerkzeugs nicht beeinträchtigt wird.
VORSICHT
Von Kindern und gebrechlichen Personen fernhalten.
Werkzeuge sollten bei Nichtgebrauch außerhalb der
Reichweite von Kindern und gebrechlichen Personen
aufbewahrt werden.
FÜR SCHLEIF-, SCHMIRGEL-, POLIER- UND
TRENNSCHLEIFARBEITEN GELTENDE
SICHERHEITSHINWEISE
a) Dieses Elektrowerkzeug kann als Schleif-,
Schmirgel-, Polier-, oder Trennschleifwerkzeug
benutzt werden. Bitte beachten Sie sämtliche mit
diesem Gerät gelieferten Sicherheitshinweise,
Anweisungen, Illustrationen und technischen
Angaben.
Wenn nicht sämtliche nachstehenden Anweisungen
befolgt werden, kann es zu Stromschlag, Feuergefahr
und/oder ernsthaften Verletzungen kommen.
b) Es wird nicht empfohlen, Arbeiten wie Drahtbürsten
mit diesem Elektrowerkzeug auszuführen.
Arbeiten, für die dieses Elektrowerkzeug nicht
konzipiert wurde, könnten eine Gefahr darstellen, die
zu Verletzungen oder Geräteschäden führen könnten.
c) Verwenden Sie keine Zuberteile, die nicht
speziell vom Hersteller für die Verwendung mit
dem Werkzeug konzipiert und empfohlen wurden.
Der Umstand, dass ein Zubehörteil an dem
Elektrowerkzeug angebracht werden kann, bedeutet
nicht, dass damit ein sicherer Betrieb garantiert ist.
d) Die Nenndrehzahl des Schleifkörpers
muss mindestens der maximalen auf dem
Elektrowerkzeug angegebenen Drehzahl
entsprechen.
Schleifkörper, die mit einer höheren Geschwindigkeit
als ihrer Nenndrehzahl betrieben werden, können
zerbersten und in Folge können Bruchstücke davon
weggeschleudert werden.
e) Außendurchmesser und Dicke des Schleifkörpers
müssen den Maßangaben Ihres Elektrowerkzeugs
entsprechen.
Falsch bemessene Schleifkörper können nicht
ausreichend abgesichert oder bei Arbeit nicht
ausreichend kontrolliert werden.
f) Schleifscheiben, Flansche, Schleifteller
oder anderes Zuber müssen genau auf die
Schleifspindel Ihres Elektrowerkzeugs passen.
Einsatzwerkzeuge, die nicht genau auf die
Schleifspindel des Elektrowerkzeugs passen, laufen
mit Unwucht, vibrieren sehr stark und können zu einem
Verlust der Kontrolle über das Werkzeug führen.
g) Benutzen Sie niemals beschädigte
Schleifkörper. Überprüfen Sie vor jedem
Gebrauch Einsatzwerkzeuge wie Schleifkörper
auf Absplitterungen und Risse, Schleifteller
auf Sprünge, Risse oder starke Abnutzung,
Drahtbürsten auf lose oder gebrochene
Drähte. Wenn das Elektrowerkzeug oder der
Schleifkörper herunter fällt, überprüfen Sie es/
ihn auf Beschädigung oder montieren Sie einen
unbeschädigten Schleifkörper. Lassen Sie
Deutsch
16
nach Prüfung und Montage des Schleifkörpers
das Elektrowerkzeug eine Minute lang mit
maximaler Leerlaufdrehzahl laufen. Achten Sie
dabei darauf, dass Sie und alle anderen in der
Nähe be ndlichen Personen sich außerhalb der
Rotationsebene des Schleifkörpers aufhalten.
Normalerweise zerbersten schadhafte
Schleifwerkzeuge bei einem solchen Probelauf.
h) Tragen Sie eine Schutzausrüstung. Benutzen
Sie je nach Anwendung Gesichtsschutz oder
Schutzbrille. Soweit angemessen, tragen Sie eine
Staubmaske, einen Gerschutz, Handschuhe
sowie eine Arbeitsscrze, die geeignet sind,
Sie vor Schleifkörper- und Werksckteilchen zu
schützen.
Die Schutzbrille muss sich eignen, die bei
unterschiedlichen Arbeiten weggeschleuderten Partikel
abzuwehren. Die Staub- oder die Atemschutzmaske
muss in der Lage sein, die bei der Arbeit entstehenden
Partikel zu ltern. Eine dauerhaft hohe Lärmbelastung
kann zu Gehörverlust führen.
i) Halten Sie umstehende Personen von Ihrem
Arbeitsbereich fern. Jeder, der den Arbeitsbereich
betritt, muss eine Schutzausrüstung tragen.
Werkstückteilchen oder Stücke geborstener
Schleifkörper können weggeschleudert werden und
auch außerhalb des unmittelbaren Arbeitsbereiches
Verletzungen verursachen.
j) Falls der Schleifkörper bei der Arbeit mit
versteckt liegenden Leitungen oder mit der
Anschlussleitung des Elektrowerkzeugs
selbst in Berührung kommen kann, halten Sie
das Elektrowerkzeug nur an seinen isolierten
Gri ächen.
Schleifkörper, die in Kontakt mit einer
spannungsführenden Leitung kommen, können die
Metallteile des Elektrowerkzeugs spannungsführend
machen und dem Bediener einen elektrischen Schlag
versetzen.
k) Halten Sie die Anschlussleitung des
Elektrowerkzeugs stets vom drehenden
Schleifkörper fern.
Falls Sie die Kontrolle über das Elektrowerkzeug
verlieren, kann die Anschlussleitung durchtrennt oder
erfasst werden, und Ihre Hand oder Ihr Arm in das sich
drehende Einsatzwerkzeug geraten.
l) Legen Sie das Elektrowerkzeug niemals ab, bevor
der Schleifkörper vollständig zum Stillstand
gekommen ist.
Der sich drehende Schleifkörper kann in Berührung mit
der Ablage äche geraten, wodurch Sie die Kontrolle
über das Elektrowerkzeug verlieren können.
m) Lassen Sie das Elektrowerkzeug nicht laufen,
während Sie es tragen.
Der sich drehende Schleifkörper kann bei
versehentlicher Berührung Ihre Kleidung erfassen und
in Ihren Körper gezogen werden.
n) Reinigen Sie regelßig die Lüftung nungen
des Elektrowerkzeugs. Das Motorgebläse zieht
Staub in das Geuse.
Übermäßige Ansammlungen von Metallstaub könnten
zu elektrischen Gefährdungen führen.
o) Verwenden Sie das Elektrowerkzeug nicht in der
Nähe ent ammbarer Materialien.
Funken könnten diese Materialien entzünden.
p) Verwenden Sie keine Zubehörteile, die üssige
Kühlmittel erfordern.
Die Verwendung von Wasser oder anderen üssigen
Kühlmitteln kann zu einem elektrischen Schlag oder
Schock führen.
RÜCKSCHLAG UND DAZU GEHÖRIGE
SICHERHEITSHINWEISE
ckschlag ist die plötzliche Reaktion infolge eines
Verklemmens oder Verhakens eines drehenden
Schleifkörpers, eines Schleiftellers oder einer Drahtbürste
etc. Dieses Verklemmen oder Verhaken führt zu einem
plötzlichen Stopp des rotierenden Schleifkörpers, wodurch
ein unkontrolliertes Elektrowerkzeug an der Blockierstelle
ruckartig gegen die Drehrichtung des Schleifkörpers
bewegt wird.
Wenn beispielsweise eine Schleifscheibe im Werkstück
verklemmt oder verhakt wird, kann sich die Kante der
in die Blockierstelle eindringenden Schleifscheibe in
die Ober äche des Werkstücks graben, wodurch die
Schleifscheibe ausbrechen oder einen Rückschlag
verursachen kann. Je nach Drehrichtung der Scheibe
an der Blockierstelle kann sich die Schleifscheibe dabei
auf die Bedienperson zu oder von ihr weg bewegen.
Schleifscheiben können unter diesen Umständen auch
brechen.
Zum Rückschlag kommt es in Folge einer falschen
und/oder nicht ordnungsgemäßen Verwendung
des Elektrowerkzeugs. Dies kann durch geeignete
Vorsichtsmnahmen vermieden werden, die im
Folgenden beschrieben werden.
a) Halten Sie das Elektrowerkzeug stets gut fest und
bringen Sie Ihren Körper und Ihren Arm in eine
Position, in der Sie mögliche Rückschlagkräfte
abfangen können. Verwenden Sie immer den
Zusatzgri , falls vorhanden, um beim Hochlauf die
größtgliche Kontrolle über Rückschlagkfte
oder Reaktionsmomente zu haben.
Der Bediener kann Rückschlagkräfte
oder Reaktionsmomente durch geeignete
Vorsichtsmaßnahmen beherrschen.
b) Bringen Sie Ihre Hand nie in die Nähe rotierenden
Einsatzwerkzeuge.
Das Einsatzwerkzeug könnte sich beim Rückschlag
über Ihre Hand bewegen.
c) Meiden Sie den Bereich, in den sich das
Elektrowerkzeug bei einem Rückschlag bewegen
würde.
Durch den Rückschlag wird das Elektrowerkzeug
ruckartig entgegen der Drehrichtung der Schleifscheibe
an der Blockierstelle bewegt.
d) Arbeiten Sie besonders vorsichtig im Bereich
von Ecken und scharfen Kanten etc. Verhindern
Sie, dass Einsatzwerkzeuge vom Werkstück
zurückprallen und verklemmen.
An Ecken und scharfen Kanten oder beim Abprallen
neigen rotierende Einsatzwerkzeuge dazu, sich zu
verklemmen, was in weiterer Folge zum Verlust der
Kontrolle des Werkzeugs oder zum Rückschlag führt.
e) Verwenden Sie kein Ketten- oder gezähntes
Sägeblatt.
Solche Einsatzwerkzeuge führen häu g zu
ckschlag oder zum Verlust der Kontrolle über das
Elektrowerkzeug.
BESONDERE SICHERHEITSHINWEISE FÜR
SCHLEIF- BZW. TRENNSCHLEIFARBEITEN
a) Verwenden Sie lediglich die für Ihr
Elektrowerkzeug zugelassenen Schleifkörper
und die für diese Schleifkörper vorgesehene
Schutzhaube.
Deutsch
17
Schleifkörper, die nicht für das Elektrowerkzeug
vorgesehen sind, können nicht ausreichend
abgeschirmt werden und ihre Verwendung ist daher
nicht sicher.
b) Schleifkörper dürfen nur für die jeweils
vorgesehenen Einsatzmöglichkeiten verwendet
werden. Schleifen Sie beispielsweise nie mit der
Seiten äche einer Trennscheibe.
Trennscheiben sind zum Abtragen von Material durch
die Scheibenkante bestimmt und können bei seitlicher
Krafteinwirkung auf den Schleifkörper zerbrechen.
c) Verwenden Sie immer unbeschädigte Flansche
in der für die gewählte Schleifscheibe passenden
Größe und Form.
Passende Flansche stützen die Schleifscheibe und
verringern so die Gefahr eines Zerbrechens der
Schleifscheibe. Flansche für Trennscheiben können
sich von Flanschen für andere Schleifscheiben
unterscheiden.
d) Verwenden Sie niemals durch gßere
Elektrowerkzeuge abgenutzte Schleifscheiben.
Für größere Elektrowerkzeuge konzipierte
Schleifscheiben sind nicht für die höheren Drehzahlen
kleinerer Elektrowerkzeuge ausgelegt und können
brechen.
WEITERE SICHERHEITSHINWEISE ZU
TRENNSCHLEIFARBEITEN
a) Vermeiden Sie ein Blockieren der Trennscheibe
oder das Ausüben übertriebenen Drucks auf die
Trennscheibe. Versuchen Sie nicht, überßig
tiefe Schnitte auszuführen.
Durch das Überlasten der Trennscheibe erhöht
sich deren Beanspruchung und die Anfälligkeit
zum Verkanten oder Blockieren und damit die
glichkeit eines Rückschlags oder Zerbrechens des
Schleifkörpers.
b) Meiden Sie den Bereich vor und hinter der
rotierenden Trennscheibe.
Bewegt sich die Trennscheibe im Werksck von
Ihnen weg, so kann im Falle eines Rückschlags das
Elektrowerkzeug mit der sich drehenden Scheibe
direkt auf Sie zugeschleudert werden.
c) Falls die Trennscheibe verklemmt oder Sie die
Arbeit aus irgendeinem Grund unterbrechen
müssen, schalten Sie das Elektrowerkzeug
aus und halten Sie es an derselben Stelle, bis
die Scheibe völlig zum Stillstand gekommen
ist. Versuchen Sie niemals, eine noch laufende
Trennscheibe aus dem Schnitt zu ziehen, sonst
kann dies zu einem Rückschlag führen.
Ermitteln und beheben Sie die Ursache für das
Verklemmen der Scheibe.
d) Schalten Sie das Elektrowerkzeug nicht wieder
ein, solange es sich noch im Werksck be ndet.
Warten Sie nach dem Einschalten bis die
Trennscheibe ihre volle Geschwindigkeit erreicht
hat, bevor Sie das Werkzeug vorsichtig wieder in
den Schnitt einsetzen.
Ansonsten kann die Scheibe blockieren, aus
dem Werkstück springen oder einen Rückschlag
verursachen.
ALLGEMEINE SICHERHEITSANWEISUNGEN
FÜR AKKU-GERADSCHLEIFER
Vergewissern Sie sich, dass die auf der
Scheibe angegebene Geschwindigkeit mit der
Sollgeschwindigkeit des Schleifers übereinstimmt oder
diese übertri t;
Achten Sie darauf, dass die Abmessungen der
Scheibe mit dem Schleifer kompatibel sind;
Schleifscheiben müssen sorgfältig und in
Übereinstimmung mit den Anweisungen des
Herstellers gelagert und verwendet werden;
Überprüfen Sie die Schleifscheibe vor dem Einsatz,
verwenden Sie keine angeschlagenen, gebrochenen
oder sonstwie defekte Produkte;
Achten Sie darauf, dass Scheiben und Gegenscke
gemäß den Anweisungen des Herstellers angebracht
werden;
Denken Sie daran, mit dem Verbundprodukt gelieferte
Papier ansche zu verwenden, wenn diese benötigt
werden;
– Benutzen Sie das Elektrowerkzeug nicht zum
Bearbeiten von gesundheitsschädlichen Materialien.
Benutzen Sie das angegebene Zubehör bzw. den
angegebenen Aufsatz.
– Achten Sie darauf, dass das Schleifmittel vor dem
Einsatz richtig montiert und angezogen wird, lassen
Sie das Werkzeug 30 Sekunden lang unbelastet
in einer sicheren Position laufen, stoppen Sie das
Gerät sofort, falls Sie deutliche Vibrationen oder
andere Defekte bemerken sollten. Falls dies eintritt,
überpfen Sie das Get und versuchen Sie, die
Ursache herauszu nden;
Falls das Werkzeug mit einer Schutzeinrichtung
ausgestet ist, benutzen Sie das Werkzeug niemals
ohne diese Schutzeinrichtung;
Verwenden Sie keine separaten Reduzierhülsen
oder Adapter, um Schleifscheiben mit großem
Lochdurchmesser zu montieren;
Bei Werkzeugen, die zum Einsatz mit Gewinde-
Schleifscheiben vorgesehen sind, vergewissern Sie
sich, dass das Gewinde in der Scheibe lang genug ist,
um die Welle in ganzer Länge aufzunehmen;
– Vergewissern Sie sich, dass das Werkstück richtig
gestützt wird;
Verwenden Sie keine Trennscheiben für seitliche
Schleifarbeiten;
Achten Sie darauf, dass bei der Arbeit entstehende
Funken keine Unfälle verursachen – keine Personen
tre en oder ent ammbare Materialien entnden;
Sorgen Sie dafür, dass Belüftung nungen jederzeit
frei bleiben, wenn Sie unter staubigen Bedingungen
arbeiten. Falls Staub beseitigt werden muss, ziehen
Sie zuerst den Netzstecker (verwenden Sie dafür
keine Metallgegensnde) und vermeiden Sie
Beschädigungen von innen liegenden Teilen;
Tragen Sie grundsätzlich eine Schutzbrille und einen
Gehörschutz. Darüber hinaus sollten Sie in eine
persönliche Schutzausrüstung wie Staubmaske,
Handschuhe, Helm und Schürze tragen;
Geben Sie gut auf die Scheibe acht; nach dem
Ausschalten des Werkzeuges dreht sich diese noch
eine Zeit lang weiter.
Die Batterie immer bei einer Temperatur von 0 – 40°C
laden.
Laden bei einer Temperatur die niedriger als 0°C
is twird gefährliche Überladung verursachen. Die
Batterie kann nicht bei einer Temperatur über 4C
geladen werden. Die beste Temperatur zum Laden
wäre von 20 – 25°C.
Deutsch
18
Das Ladegerät nicht fortlaufend laden.
Nach Beendung einer Ladung, lassen Sie das
Ladegerät ungefähr 15 Minuten ruhen bevor die
nächste Batterieladung unternommen wird.
Keine Fremdkörper durch das Anschlußloch der
Batterie eindringen lassen.
Niemals die Batterie und das Ladeget
auseinandernehmen.
Niemals die Batterie kurzschließen.
Kurzschluß der Batterie verursacht eine zu gre
Stromzufuhr und Überhitzung, wodurch Durchbrennen
oder Schaden beider Batterie ensteht.
Die Batterie nicht ins Feuer werfen.
Sie könnte dabei explodieren.
Wenn Sie in Wände, Boden, oder Decke bohren,
suchen Sie vorher nach darin verlegten elektrischen
Leitungen usw.
Darauf achten, daß keine Gegensnde durch
Belüftungsschlitze des Au aders in das Gerät
eindringen.
Wenn Metallobjekte oder entzündliche Gegenstände
durch die Belüftungsschlitze des Au aders eindringen,
kann dies zu elektrischen Schlägen führen oder den
Au ader beschädigen.
Bringen Sie die Batterie zum Geschäft, wo Sie ihn
gekauft haben sobald die Lebensdauer der Batterie
abrinnent. Die erschöpfte Batterie nicht wegwerfen.
Benutzung verbrauchter Batterie beschädigt den
Au ader.
WARNUNG ZUM LITHIUM-IONEN-AKKU
Um die Lebensdauer des Lithium-Ionen-Akkus zu
verlängern, ist dieser mit einer Schutzfunktion zum
Stoppen der Leistungsabgabe ausgestattet.
In den unten beschriebenen Fällen 1 bis 3 kann bei der
Benutzung dieses Produkts der Motor abschalten, selbst
wenn Sie den Schalter dcken. Dies ist kein Defekt
sondern das Resultat der Schutzfunktion.
1. Wenn die verbleibende Akkuleistung nicht mehr
ausreicht, schaltet der Motor ab.
Laden Sie in einem solchen Fall den Akku umgehend
auf.
2. Wenn das Werkzeug überlastet ist, kann es zum
Abschalten des Motors kommen. Lassen Sie in diesem
Fall den Schalter des Geräts los und beseitigen Sie die
Ursache der Überlastung. Danach können Sie das
Gerät wieder verwenden.
3. Kommt es während des Betriebs zu einer Erhitzung der
Batterie, wird das Get unter Umständen angehalten.
Unterbrechen Sie in diesem Fall Ihre Arbeit und lassen
Sie die Batterie abkühlen. Anschliend können Sie
das Gerät wieder normal verwenden.
Bitte beachten Sie die folgenden Warnhinweise.
WARNUNG
Zur Vermeidung einer ausgelaufenen Batterie, Erwärmung,
Rauchentwicklung, Explosionen und vorzeitiger Zündung
beachten Sie bitte die folgenden Vorsichtsmaßnahmen.
1. Stellen Sie sicher, dass sich Späne und Staub nicht
auf der Batterie ansammeln.
Stellen Sie während der Arbeit sicher, dass Späne und
Staub nicht auf die Batterie fallen.
Stellen Sie sicher, dass Staub und Späne, die während
der Bearbeitung auf das Elektrowerkzeug fallen, nicht
in die Batterie gelangen.
Lagern Sie ungebrauchte Batterien nicht an Plätzen,
an denen Staub oder Späne anfallen.
Vor dem Einlagern einer Batterie sind sämtlicher
Staub und Späne zu entfernen. Weiterhin ist zu
berücksichtigen, dass die Batterie nicht gemeinsam
mit Metallteilen (Schrauben, Nägel, usw.) zu lagern ist.
2. Achten Sie darauf, dass die Batterie nicht durch einen
spitzen Gegenstand, beispielsweise einen Nagel,
beschädigt wird. Vermeiden Sie Schläge mit dem
Hammer. Treten Sie nicht gegen die Batterie, werfen
Sie diese nicht, und vermeiden Sie Stöße.
3. Beschädigte oder verformte Batterien dürfen nicht
weiter verwendet werden.
4. Achten Sie auf den richtigen Anschluss der Pole.
5. Schließen Sie die Batterie nicht direkt an elektrische
Ausgänge oder Zigarettenanzünder im Auto an.
6. Verwenden Sie die Batterie nur für den angegebenen
Zweck.
7. Falls die Batterie nach Verstreichen der angegebenen
Ladezeit nicht vollsndig aufgeladen ist, brechen Sie
den Ladevorgang unverzüglich ab.
8. Vermeiden Sie hohe Temperaturen und hohen
Druck, wie er beispielsweise in der Mikrowelle, einem
Trockner oder einem Hochdruckbelter auftritt.
9. Wenn Sie ein Leck oder Rußgeruch feststellen,
vermeiden Sie jeglichen Kontakt mit Feuerstellen.
10. Vermeiden Sie eine Verwendung an Orten, an denen
starke statische Elektrizität erzeugt wird.
11. Werden ein Leck, Rußgeruch, Erwärmung,
Verfärbungen, Verformungen oder sonstige
Anomalitäten während der Verwendung, des Au adens
oder der Lagerung festgestellt, entfernen Sie die
Batterie unverzüglich vom Gerät oder dem Ladeget
und beenden Sie die Anwendung.
VORSICHT
1. Tritt die auslaufende Flüssigkeit in Kontakt mit Ihren
Augen, reiben Sie diese nicht, sondern waschen Sie
sie mit sauberem (Leitungs-) Wasser gut aus und
suchen Sie unverzüglich einen Arzt auf.
Ohne sachgemäße Behandlung können
Augenverletzungen auftreten.
2. Wenn die ausgelaufene Flüssigkeit auf Haut oder
Kleidung tri t, waschen Sie diese unverzüglich mit
sauberem Wasser ab.
Es besteht die Gefahr von Hautreizungen.
3. Beim Auftreten von Rost, Rußgeruch, Erwärmung,
Verfärbungen, Verformungen oder sonstigen
Anomalitäten während der ersten Verwendung der
Batterie, ist diese nicht weiter zu verwenden. Bringen
Sie die Batterie zum Händler oder Verkäufer zurück.
WARNUNG
Wenn ein elektrischer Fremdkörper an die Anschlüsse
des Lithium-Ionen-Akkus gelangt, kann es zu einem
Kurzschluss und der Gefahr eines Feuers kommen.
Beachten Sie folgende Vorsichtsmaßnahmen bei der
Aufbewahrung des Akkus.
Legen Sie keine elektrisch leitenden Sne,
Nägel, Stahldraht, Kupferdraht oder anderen
Draht in den Aufbewahrungsko er.
Deutsch
19
TECHNISCHE DATEN
ELEKTRO-WERKZEUG
Leerlaufdrehzahl 5000 – 35000 min
–1
Nenndrehzahl 34000 min
–1
Spannfutterkapazität 3,2 mm
Wiederau adbare Batterie BCL1015: Li-ion 10,8 V (1,5 Ah 3 Zellen)
Gewicht 0,48 kg
LADEGET
Model UC10SL2 UC10SFL
Ladespannung 10,8 V 10,8 V
Gewicht 0,35 kg 0,35 kg
STANDARDZUBEHÖR
GP10DL
(LCSK)
1 Zubehöre × 40 Stk. ........................... 1
2 Batterie (BCL1015) ........................... 1
3
Ladegerät (UC10SL2 or UC10SFL)
... 1
4 Plastikgehäus ................................... 1
GP10DL
(NN)
1 Zubehöre × 40 Stk. ........................... 1
Details zu den Aufsätzen nden Sie inMitgelieferte
Aufsätze“.
Das Standardzubehör kann ohne vorherige
Bekanntmachung jederzeit gndert werden.
Deutsch
20
1 / 1

Hitachi GP 10DL Handling Instructions Manual

Kategória
Elektrické náradie
Typ
Handling Instructions Manual

V iných jazykoch