Candy CDG6CBG Používateľská príručka

EN Instruction manual 2

FR Manuel d'instructions

ES

CS

HU

SK

Manual de instrucciones

Návod k použití

Kezelési útmutató

Návod na použitie 67

80

PL

Instrukcja obsługi

1

CDG6CBG

Cooker Hood

Hotte de cuisson

Campana extractora

Odsavač nad sporák

Páraelszívó

Digestor

Okap kuchenny

CDG6CBG

Cooker Hood

Instruction Manual

2

Content

1. Safety instructions 4

2. Installation 6

3. Start using your cooker hood 10

4. Troubleshooting 10

5. Maintenance and cleaning 11

6. Environment protection 14

3

SAFETY INSTRUCTIONS

This manual explains the proper installation and use of your cooker hood,

please read it carefully before using even if you are familiar with the product.

The manual should be kept in a safe place for future reference.

Never to do:

● D o not try to use the cooker hood

without the grease filters or if the filters

are excessively greasy!

●Do not install above a cooker with a

high level grill.

●Do not leave frying pans unattended

during use because overheated fats or

oils might catch fire.

●Never leave naked flames under the

cooker hood.

●If the cooker hood is damaged, do not

attempt to use.

●Do not flambé under the cooker hood.

●CAUTION: Accessible parts may

become hot when used with cooking

appliances.

●The minimum distance between the

supporting surface for the cooking

vessels on the hob and the lowest part

of the cooker hood. (When the cooker

hood is located above a gas appliance,

this distance shall be at least 65 cm)

●The air must not be discharged into a

flue that is used for exhausting fumes

from appliances burning gas or other

fuels.

Always to do:

● Important! Always switch off the

electricity supply at the mains during

installation and maintenance such as

light bulb replacement.

●The cooker hood must be installed in

accordance with the installation

instructions and all measurements

followed.

●All installation work must be carried

out by a competent person or qualified

electrician.

●Please dispose of the packing material

carefully. Children are vulnerable to it.

● P ay attention to the sharp edges

inside the cooker hood especially

during installation and cleaning.

●Make sure the ducting has no bends

sharper than 90 degrees as this will

reduce the efficiency of the cooker

hood.

●Warning: Failure to install the screws

or fixing device in accordance with

these instructions may result in

electrical hazards.

●Warning: Before obtaining access to

terminals, all supply circuits must be

disconnected.

4

Always to do:

●Always put lids on pots and pans

when cooking on a gas cooker.

●When in extraction mode, air in the

room is being removed by the cooker

hood. Please make sure that proper

ventilation measures are being

observed. The cooker hood removes

odours from room but not steam.

●Cooker hood is for domestic use only.

●If the supply cord is damaged, it must

be replaced by the manufacturer, its

service agent or similarly qualified

persons in order to avoid a hazard.

●This appliance can be used by

children aged from 8 years and above

and persons with reduced physical,

sensory or mental capabilities or lack

of experience and knowledge if they

have been given supervision or

instruction concerning use of the

appliance in a safe way and

understand the hazards involved.

Children shall not play with the

appliance. Cleaning and user

maintenance shall not be made by

children without supervision.

Always to do:

● Caution: The appliance and its

accessible parts can become hot

during operation. Be careful to avoid

touching the heating elements.

Children younger than 8 years old

should stay away unless they are

under permanent supervision.

● There shall be adequate ventilation of

the room when the range hood is used

at the same time as appliances

burning gas or other fuels.

●There is a fire risk if cleaning is not

carried out in accordance with the

instructions.

●Regulations concerning the discharge

of air have to be fulfilled.

●Clean your appliance periodically by

following the method given in the

chapter MAINTENANCE.

●For safety reason, please use only the

same size of fixing or mounting screw

which are recommended in this

instruction manual.

●Regarding the details about the

method and frequency of cleaning,

please refer to maintenance and

cleaning section in the instruction

manual.

●Cleaning and user maintenance shall

not be made by children without

supervision.

●When the range hood and appliances

supplied with energy other than

electricity are simultaneously in

operation, the negative pressure in the

room must not exceed 4 Pa (4 x 10-5

bar).

●WARNING: Danger of fire: do not

store items on the cooking surfaces.

●A steam cleaner is not to be used.

●NEVER try to extinguish a fire with

water, but switch off the appliance and

then cover flame e.g. with a lid or a

fire blanket.

5

INSTALLATION (VENT OUTSIDE)

MOUNTING OF THE V-FLAP

If the cooker hood does not have an assembled V-flap 1, you should mount the half-

parts to its body.The images only show an example of how to mount the V-flap,

becausethe outlet may vary according to different models and configurations.

To mount the V-flap 1 you should:

• Mount two half-parts 2 into the body 6

• the pin 3 should be top oriented;

• the axis 4 should be inserted into the holes 5 on the body;

• repeat all the operations for the 2nd half-part.

INSTALLATION

If you have an outlet to the outside, your cooker hood can be connected as below

picture by means of an extraction duct (enamel, aluminum, flexible pipe or non-

flammable material with an interior diameter of 150mm)

1. Before installation, turn the unit off.

2. The cooker hood should be placed at a distance of 65~75cm above the cooking

surface for best effect.

ʒ

ʗ

ʕʓʔʖ

6

3. After decide the cooker hood height, measure the position of the holes for hanging

hood,inside chimney bracket ,outside chimney bracket and safety holes. Drill 8 φ8

holes and insert wall plugs into the holes. Fix the inside chimney bracket on the

wall with 2pcs ST4 x 40mm screws.Screw 2pcs ST4 x 8mm screws in the hole for

hanging the hood body and the screws installed should leave for 3-5mm out of the

wall to hang the hood.The fixed position of the inside chimney bracket is the

highest place of chimney. See pic 2.

65cm

75cm

Pic 1

4. Install the v-flap(not included) and expansion pipe(not included) onto the cooker

hood. Fix the expansion pipe on the outlet with a cable tie. Please note: The

expansion pipe and v-flap are not included in the product. See Pic 3.

5. Hang the cooker hood onto the hook.See pic 4.

7

6. Install the outside chimney bracket onto the outside chimney with 2pcs ST4*8mm

screws, here should be sure the inside chimney can be flexed freely.See Pic 5.

7. Fix the cooker hood with 2pcs ST4*30mm safety screws. Note: The two safety

vents are positioned on the back housing, with a diameter of 6mm.Put the two

chimneys onto the cooker hood, fix the outside chimney on the wall with 2pcs

ST4*40mm screws and lead the expansion pipe to the outside. See pic 6.

8. Adjust the height of the inside chimney to the position of the inside chimney bracket

and fix it with 2pcs ST4*8mm screws. Fix the outside chimney onto the hood body

with 2pcs ST4*8mm screws.See Pic 7.

Electrical Installation

All installation must be carried out by a competent person or qualified electrician.

Before connecting the mains supply ensure that the mains voltage corresponds to the

voltage on the rating plate.

Direct Connection

The appliance must be connected directly to the mains using an omnipolar circuit

breaker with a minimum opening of 3mm between the contacts.

The installer must ensure that the correct electrical connection has been made and

that it complies with the wiring diagram.

The cable must not be bent or compressed.

Regularly check the power plug and power cord for damage. If the supply cord is

damaged, it must be replaced by a special cord or assembly available

from the manufacturer or its service agent.

WARNING: This is a Class I appliance and MUST be earthed

This appliance is supplied with a 3 core mains cable coloured as follows:

Brown = L or Live

Blue = N or Neutral

Green and Yellow = E or Earth

8

HINTS FOR EXHAUST DUCT INSTALLATION

The following rules must be strictly followed to obtain optimal air extraction:

• Keep exhaust duct short and straight

• Do not reduce the size or restrict the exhaust duct

• When using the flexible duct always install the duct pulled taut to minimize pressure

loss.

• Failure to observe these basic instructions will reduce the performance and increase

noise levels of the range hood.

• Any installation work must be carried out by a qualified electrician or competent

person.

• Do not connect the ducting system of the hood to any existing ventilation system

which is being used for any other appliance ,such as warmer tube, gas tube , hot wind

tube.

• The angle of the bend of the ventilation pipe should not be less than 120º; you must

direct the pipe horizontally, or, alternatively, the pipe should go up from the initial point

and should be led to an outer wall.

• After the installation ,make sure that the cooker hood is level to avoid grease

collection at on end.

Ensure the exhaust ducting selected for installation complies with relevant standards

and is fire retardant.

WARNING:

Right Wrong

 For safety reason, please use only the same

size of fixing or mounting screws which are

recommended in this instruction manual.

 Failure to install the screws or fixing device in

accordance with these instructions may result in

electrical hazards.

9

Start Using Your Cooker Hood

Touch control

Timer Lamp Speed Power

1. Press the “Power” button, the button control the “on” & “off ” of the hood.

2. Press the button “Speed” time after time, the motor runs as low / mid / high / low /

mid…, the speed runs circularly; and the LED display will indicate as 1-2-3-1-2…

circularly.

3. Press “Lamp” button, the light is on, press this button again, the light is off. Please

note the Lamp is not under control of the on/off button.

4. When the hood is working, if press the “Timer” button, the hood will go into the

status of acquiescent working (acquiescent time is 9mins), and then, LED display

will be shown 9.8.7.6 ...decreasing by 1,when time is up, the hood will be off

automatically and the lamp will extinguish. If pressing “Timer” button, the hood will

go in or go out “Timer” function.

TROUBLESHOOTING

Fault Possible Cause Solution

Light on, but motor

does not work

Fan switch turned off Select a fan switch position.

Fan switch failed Contact service center.

Motor failed Contact service center.

Light does not

work, motor does

not work

House fuses blown Reset/Replace fuses.

Mains power cable is loose or

disconnected

Refit mains power cable to

power outlet.

Switch power outlet on.

Oil leakage

One way valve and the outlet

are not tightly sealed

Take down the one way valve

and seal with sealant.

Leakage from the connection of

chimney and cover Take chimney down and seal.

Lights not working Broken or faulty bulbs Replace blubs as per this

instruction.

Insufficient suction

The distance between the

cooker hood and the gas top is

too far

Refit the cooker hood to the

correct distance.

The Cooker hood

inclines

The fixing screw is not tight

enough

Tighten the hanging screw and

make it horizontal.

10

NOTE:

Any electrical repairs to this appliance must conform to your local, state and

federal laws.Please contact the service centre if in any doubt before

undertaking any of the above.Always disconnect the unit from the power source when

opening the unit.

MAINTENANCE AND CLEANING

Caution:

• Before maintenance or cleaning is carried out, the cooker hood should be

disconnected from the mains power supply. Ensure that the cooker hood is switched

off at the wall socket.

• External surfaces are susceptible to scratches and abrasions, so please follow the

cleaning instructions to ensure the best possible result is achieved without damage.

GENERAL

Cleaning and maintenance should be carried out with the appliance cold especially

when cleaning.Avoid leaving alkaline or acid substances (lemon juice, vinegar etc.) on

the surfaces.

STAINLESS STEEL

The stainless steel must be cleaned regularly (e.g.weekly) to ensure a long life

expectancy.Dry with a clean soft cloth. A specialized stainless steel cleaning fluid may

be used.

NOTE:

Ensure that wiping is done along with the grain of the stainless steel to prevent any

unsightly crisscross scratching patterns from appearing.

CONTROL PANEL SURFACE

The inlay control panel can be cleaned using warm soapy water. Ensure the cloth is

clean and well wrung before cleaning. Use a dry soft cloth to remove any excess

moisture left after cleaning.

Important

Using neutral detergents and avoid using harsh cleaning chemicals, strong household

detergents or products containing abrasives,as this will affect the appearance of the

appliance and potentially remove any printing of artwork on the control panel and will

void manufactures warrantee.

GREASE MESH FILTERS

The mesh filters can be cleaned by hand. Soak them for about 3 minute in water with a

mild detergent then brush it gently with a soft brush. Please do not apply too much

pressure, avoid to damage it . (Leave to dry naturally out of direct sun light)

Filters should be washed separately to crockery and kitchen utensils. It is advisable

not to use rinse aid. Following the picture beside to dismantle the grease filter.

11

INSTALLING GREASE MESH FILTERS

• To install filters for the following four steps:

- Angle the filter into the slots at the back of the hood.

- Push the button on the handle of the filter.

- Release the handle once the filter fits into a resting position.

- Repeat to install all filters.

CARBON FILTER- not supplied

Activated carbon filter can be used to trap odors. Normally the activated carbon filter

should be changed every 3 to 6 months according to your cooking habits. The

installation procedure of activated carbon filter is as below:

1. Before installing or replacing the carbon filters, please disconnect mains power

to the unit.

2. Press the filter lock and remove the mesh filter.

3. Turn the carbon filter on both sides of the motor anti-clockwise. Replace the

carbon filters with the new carbon filters.

4. Place the mesh filter.

5. Connect the power supply to the wall socket.

NOTE:

 Make sure the filter is securely locked. Otherwise, it would loosen and cause

danger.

 When activated carbon filter attached, the suction power will be lowered.

12

BULB REPLACEMENT

Important :

 The bulb must be replaced by the manufacturer, its

service agent or similarly qualified persons.

 Always switch off the electricity supply before

carrying out any operations on the appliance. When

handling bulb, make sure it has completely cooled

down before any direct contact with hands.

 When handling bulbs hold with a cloth or gloves to

ensure perspiration does not come in contact with

the bulb as this can reduce the life of the bulb.

Note:

 Before replacing light that the cooker hood can be isolated from the supply

mains by means of a plug or an all-pole switch.

 Protect against danger when changing lights, such as wearing gloves.

Changing the lights:

 Remove the grease filter.

 Way 1. Use a tool or the hand to press the spring splinter of both sides of LED light

to the inside, until the light is pressed out, see pic 1.Then slightly pull the light

connecting wire out, and dismantle the terminal of the light connecting wire. See

pic 2.

Way 2.Use straight screwdriver to prize up the LED light bottom edge, see pic 3,

then slightly pull out the LED light and light connecting wire. See pic 2.

 Apply the reverse procedure to install the light back.

• ILCOS D code for this lamp is: DSS-1.5/65-S-120/33

– LED modules –rectangle LED lamp

– Max wattage: 1×1.5W

– Voltage range: DC 12V

– Dimensions:

120±1

33±0.5

13

ENVIRONMENTAL PROTECTION:

This product is marked with the symbol on the selective sorting of

waste electronic equipment. This means that this product must not

be disposed of with household waste but must be supported by a

system of selective collection in accordance with Directive

2012/19/EU. It will then be recycled or dismantled to minimize

impacts on the environment, electrical and electronic products are

potentially dangerous for the environment and human health due to

the presence of hazardous substances.For more information, please

contact your local or regional authorities.

NOTE:

The following shows how to reduce total environmental impact (e.g. energy use) of the

cooking process).

(1) Install the cooker hood in a proper place where there is efficient ventilation.

(2) Clean the cooker hood regularly so as not to block the airway.

(3) Remember to switch off the cooker hood light after cooking.

(4) Remember to switch off the cooker hood after cooking.

INFORMATION FOR DISMANTLING

Do not dismantle the appliance in a way which is not shown in the user manual. The

appliance could not be dismantled by user. At the end of life, the appliance should

not be disposed of with household waste. Check with your Local Authority or retainer

for recycling advice.

14

CDG6CBG

Hotte de cuisson

Manuel d'instructions

15

Sommaire

1. Consignesde sécurité 17

2. Installation 19

3. Comment utiliser votre hotte de cuisson 23

4. Dépannage 23

5. Entretien et nettoyage 24

6. Protection de l'environnement 27

16

CONSIGNES DE SÉCURITÉ

Ce manuel indique comment installer votre hotte de cuisson et comment vous en servir.

Avant toute utilisation, veuillez le lire attentivement, même si vous connaissez déjà ce produit.

Conservez ce manuel dans un endroit sûr, pour pouvoir le consulter par la suite.

Avertissements :

● N’essayez pas d’utiliser la hotte sans

filtres à graisse ou si les filtres ont trop

de graisse.

● N’installez pas la hotte au-dessus d’une

cuisinière comportant un gril élevé.

● Ne laissez pas de friture sans

surveillance pendant l’utilisation de la

hotte, car il existe un risque d’incendie

avec la graisse chaude ou l’huile.

● Ne laissez jamais de flammes nues sous

la hotte.

● Si la hotte est endommagée, ne l’utilisez

pas.

● Ne pas faire flamber les aliments sous la

hotte.

● PRUDENCE : Les pièces accessibles

peuvent être chaudes lorsqu’elles sont

utilisées avec des appareils de cuisson.

● Distance minimale entre la surface

d’appui des récipients de cuisson sur la

plaque et la partie la plus basse de la

hotte. (Si la hotte de cuisson est

installée au-dessus d’un dispositif

fonctionnant au gaz, la distance est

65 cm)

● L’air ne doit pas être évacué par un

conduit utilisé pour l’évacuation des

fumées d’autres appareils à gaz ou

alimentés par d’autres carburants.

Ne jamais oublier de :

● Important ! Veuillez toujours couper

l’alimentation électrique au secteur

pendant l’installation ou l’entretien,

comme par exemple le remplacement

d’une ampoule électrique.

● La hotte doit être installée conformément

aux instructions d’installation et toutes

les mesures doivent être respectées.

● Tout travail d'installation doit être

effectué par une personne compétente

ou un électricien qualifié.

● Débarrassez-vous avec soin de

l’emballage. Ils peuvent représenter un

danger pour les enfants.

● Faites attention aux bords aiguisés se

trouvant sur la hotte, notamment

pendant l’installation et le nettoyage.

● Assurez-vous que le tuyau n’ait pas de

courbure de plus de 90 degrés car ceci

réduirait l’efficacité de la hotte.

● Avertissement : Le fait de ne pas

installer les vis ou le dispositif de fixation

conformément à ces instructions peut

entraîner des risques électriques.

● Avertissement : Avant d’accéder aux

appareils, tous les circuits d’alimentation

doivent être coupés.

17

Ne jamais oublier de :

● Utilisez toujours des couvercles sur les

casseroles et poêles quand vous

cuisinez avec une gazinière.

● En modalité d’extraction, l’air de la pièce

est utilisé par la hotte. Assurez-vous que

la pièce soit bien aérée. Cette hotte

élimine les odeurs de la pièce mais pas

la vapeur.

● La hotte est prévue pour un usage

domestique uniquement.

● Si le câble d'alimentation est

endommagé, il doit être remplacé par le

fabricant, son agent d'entretien ou des

personnes dotées du même type de

qualification, afin d'éviter tout risque.

● Cet appareil peut être utilisé par des

enfants âgés de 8 ans et plus, par des

personnes dont les capacités physiques,

sensorielles ou mentales sont réduites

ou par des personnes dénuées

d'expérience et de connaissances, s’ils

ont été informés de la manière d'utiliser

l'appareil en toute sécurité et s’ils

comprennent les risques qu’il implique.

Les enfants ne doivent pas jouer avec

l’appareil. L’entretien et le nettoyage ne

doivent pas être effectués par des

enfants sans surveillance.

Ne jamais oublier de :

● Attention : L’appareil et ses parties

accessibles chauffent pendant

l’utilisation. Ne pas toucher les éléments

chauds. Les enfants de moins de 8 ans

doivent se tenir éloignés, à moins qu’ils

ne soient sous surveillance permanente.

● Il doit y avoir une ventilation adéquate

de la pièce lorsque la hotte est utilisée

en même temps que des appareils à gaz

ou employant d’autres combustibles.

● Il existe un risque d’incendie si le

nettoyage n’est pas réalisé

conformément aux instructions.

● Les réglementations en matière

d’évacuation de l’air doivent être

respectées.

● Nettoyez votre appareil régulièrement en

suivant la méthode indiquée au chapitre

ENTRETIEN.

● Pour des raisons de sécurité, utilisez

uniquement des vis de fixation ou de

montage de la taille recommandée dans

ce manuel d’instructions.

● Pour des explications concernant le

mode et la fréquence de nettoyage,

veuillez consulter le chapitre entretien et

nettoyage de ce manuel d’instructions.

● L’entretien et le nettoyage ne doivent

pas être effectués par des enfants sans

surveillance.

● Lorsque la hotte et les appareils

alimentés en énergie autre que

l'électricité fonctionnent simultanément,

la pression négative dans la pièce ne

doit pas dépasser 4 Pa (4x10-5 bars).

● AVERTISSEMENT : Risque d’incendie :

ne pas stocker d’éléments sur les

surfaces de cuisson.

● N’utilisez jamais de nettoyeur à vapeur.

● N’essayez JAMAIS d’éteindre un feu

avec de l’eau, mais éteignez l’appareil,

puis couvrez la flamme avec un

couvercle ou une couverture anti-feu,

par exemple.

18

INSTALLATION (ÉVACUATION EXTERNE)

MONTAGE DU RABAT EN V

Si la hotte de cuisson n'a pas de volet en V assemblé 1, vous devez monter les demi-

pièces sur son corps. Les images ne montrent qu'un exemple de montage du volet en V,

car la sortie peut varier selon les modèles et les configurations.

Pour le montage du volet en V 1, procédez comme suit :

• montez les deux moitiés 2 dans le corps 6

• la broche 3 doit être orientée vers le haut ;

• l'axe 4 doit être inséré dans les trous 5 du corps ;

• répétez les mêmes opérations pour la deuxième moitié.

INSTALLATION

Si vous avez une sortie vers l'extérieur, votre hotte peut être connectée comme sur l’image

ci-dessous par un conduit d'évacuation (émail, aluminium, gaine souple ou matériau non

inflammable avec un diamètre intérieur de 150 mm)

1. Avant l'installation, éteignez l'appareil.

2. Pour une prestation optimale, la hotte doit être placée à une distance de 65 à 75 cm

au-dessus de la plaque de cuisson.

ʒ

ʗ

ʕʓʔʖ

19

Photo 1

3. Après avoir décidé de la hauteur de la hotte de cuisson, mesurez la position des trous

pour la hotte suspendue, le support de cheminée intérieur, le support de cheminée

extérieur et les trous de sécurité. Percez 8 φ8 trous et insérez des bouchons muraux

dans les trous. Fixez le support de cheminée intérieur au mur avec 2 vis ST4 x 40 mm.

Vissez 2 vis ST4 x 8 mm dans le trou pour accrocher le corps de la hotte et les vis

installées devraient sortir de 3 à 5 mm du mur pour accrocher la hotte. La position fixe

du support de cheminée intérieur est l'endroit le plus haut de la cheminée. Voir photo 2.

Photo 2

4. Installez le volet en V (non inclus) et le tuyau d'expansion (non inclus) sur la hotte de la

cuisinière. Fixez le tuyau d'expansion sur la sortie à l'aide d'un collier de serrage.

À noter : Le tuyau d'expansion et le volet en V ne sont pas inclus dans le produit.

Voir photo 3.

5. Accrochez la hotte de la cuisinière au crochet. Voir photo 4.

Photo 3 Photo 4

trou pour support de

cheminée extérieur

trou pour support de cheminée intérieur

trou pour

suspendre le corps

de la hotte

trous de sécurité

tube de dilatation

collier de

serrage

Volet en V

65cm

75cm

20

Stránka sa načítava ...

Candy CDG6CBG Používateľská príručka

Candy CDG6CBG Používateľská príručka

V iných jazykoch