Dometic PerfectCharge DC 08 eStore Návod na používanie

Typ
Návod na používanie
PerfectCharge DC08, DC20, DC40,
DC40 eStore
PerfectPower DCDC10, DCDC20,
DCDC40
Charger and voltage converter
Installation and Operating Manual. . . . . . . . 5
Lade- und Spannungswandler
Montage- und Bedienungsanleitung . . . . .20
Transformateur de charge et de
tension
Instructions de montage
et de service . . . . . . . . . . . . . . . . . . . . . . . . .36
Transformador de carga y tensión
Instrucciones de montaje y de uso . . . . . . .52
Conversores de carga e
transformadores de tensão
Instruções de montagem e manual de
instruções . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Trasformatore di carica e di tensione
Istruzioni di montaggio e d’uso . . . . . . . . . 84
Laad- en spanningsomvormer
Montagehandleiding en
gebruiksaanwijzing. . . . . . . . . . . . . . . . . . 100
Opladnings- og
spændingstransformer
Monterings- og betjeningsvejledning. . . 116
Laddnings- och
spänningsomvandlare
Monterings- och bruksanvisning . . . . . . . 132
Lade- og spenningsomformer
Monterings- og bruksanvisning . . . . . . . . 147
Lataus- ja jännitemuunnin
Asennus- ja käyttöohje . . . . . . . . . . . . . . . 162
Преобразователь-стабилизатор
напряжения
Инструкция по монтажу и эксплуатации 177
Przetwornik ładowania i napięcia
Instrukcja montażu i obsługi. . . . . . . . . . . 194
Nabíjací transformátor a menič
napätia
Návod na montáž a uvedenie
do prevádzky. . . . . . . . . . . . . . . . . . . . . . . 210
Napájecí měnič s měničem napětí
Návod k montáži a obsluze . . . . . . . . . . . 225
Töltés- és feszültségátalakító
Szerelési és használati útmutató . . . . . . . 240
POWER ON
BA
TTE
RY
LO
W
OVERLOAD
EN
DE
FR
ES
PT
IT
NL
DA
SV
NO
FI
RU
PL
SK
CS
HU
ENERGY & LIGHTING
CHARGERS & INVERTERS
DC08-40-DCD08-40--IO-16s.book Seite 1 Donnerstag, 28. Juli 2016 2:37 14
DC08-40-DCD08-40--IO-16s.book Seite 2 Donnerstag, 28. Juli 2016 2:37 14
PerfectCharge/PerfectPower
3
0
POWER ON
BATTERY LOW
OVERLOAD
I
1
5
6
2
7
3
4
8
1
5 cm
5 cm
POWER ON
B
A
TTE
R
Y
L
O
W
OVERLOAD
2
POWER ON
BA
TTE
RY
LOW
OVERLOAD
A
B
POWER ON
B
A
TTE
R
Y
LO
W
OVERLOAD
3
DC08-40-DCD08-40--IO-16s.book Seite 3 Donnerstag, 28. Juli 2016 2:37 14
PerfectCharge/PerfectPower
4
POWER ON
BATTERY LOW
OVERLOAD
3
1
2
4
4
15
0
I
0
I
A
B
5
DC08-40-DCD08-40--IO-16s.book Seite 4 Donnerstag, 28. Juli 2016 2:37 14
EN
PerfectCharge/PerfectPower
5
Please read this instruction manual carefully before installation and first
use, and store it in a safe place. If you pass on the product to another
person, hand over this instruction manual along with it.
Contents
1 Explanation of symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
2 General safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
3 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4 Proper use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5 Technical description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
6 Mounting the converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
7 Connecting the converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
8 Using the converter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
9 Cleaning and caring for the converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
10 Guarantee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
11 Disposal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
12 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
DC08-40-DCD08-40--IO-16s.book Seite 5 Donnerstag, 28. Juli 2016 2:37 14
EN
Explanation of symbols PerfectCharge/PerfectPower
6
1 Explanation of symbols
D
!
!
A
I
2 General safety instructions
The manufacturer accepts no liability for damage in the following cases:
Damage to the product resulting from mechanical influences and excess voltage
Alterations to the product without express permission from the manufacturer
Use for purposes other than those described in the operating manual
Note the following basic safety information when using electrical devices to protect
against:
Electric shock
Fire hazards
Injury
DANGER!
Safety instruction: Failure to observe this instruction will cause fatal or
serious injury.
WARNING!
Safety instruction: Failure to observe this instruction can cause fatal or
serious injury.
CAUTION!
Safety instruction: Failure to observe this instruction can lead to injury.
NOTICE!
Failure to observe this instruction can cause material damage and impair
the function of the product.
NOTE
Supplementary information for operating the product.
DC08-40-DCD08-40--IO-16s.book Seite 6 Donnerstag, 28. Juli 2016 2:37 14
EN
PerfectCharge/PerfectPower General safety instructions
7
2.1 General safety
D
DANGER!
In the event of fire, use a fire extinguisher which is suitable for electrical
devices.
!
WARNING!
Only use the device as intended.
Ensure that the red and black terminals never come into contact.
Disconnect the device from the mains:
Before cleaning and maintenance
Before changing a fuse
If you disassemble the device:
Detach all connections
Make sure that no voltage is present at any of the inputs and
outputs
The device may not be used if the device itself or the connection cable
are visibly damaged.
If this power cable for this device is damaged, it must be replaced by
the manufacturer, customer service or a similarly qualified person in
order to prevent safety hazards.
This device may only be repaired by qualified personnel. Inadequate
repairs may cause serious hazards.
People (including children) whose physical, sensory or mental
capacities prevent them from using this device safely may not be
allowed to operate it without the supervision of a responsible adult.
Electrical devices are not toys.
Always keep and use the appliance out of the reach of children.
Children must be supervised to ensure that they do not play with the
device.
A
NOTICE!
Before start-up, check that the voltage specification on the type plate
is the same as that of the power supply.
Ensure that other objects cannot cause a short circuit at the contacts
of the device.
Store the device in a dry and cool place.
DC08-40-DCD08-40--IO-16s.book Seite 7 Donnerstag, 28. Juli 2016 2:37 14
EN
General safety instructions PerfectCharge/PerfectPower
8
2.2 Safety when installing the device
D
DANGER!
Never mount the device anywhere where there is a risk of gas or dust
explosion.
!
CAUTION!
Ensure that the device is standing firmly.
The device must be set up and fastened in such a way that it cannot tip
over or fall down.
A
NOTICE!
Do not expose the device to a heat source (such as direct sunlight or
heating). Avoid additional heating of the device in this way.
Set up the device in a dry location where it is protected against splash-
ing water.
2.3 Safety when connecting the device electronically
D
DANGER! Danger of electrocution
For installation on boats:
If electrical devices are incorrectly installed on boats, corrosion dam-
age might occur. Have the device installed by a specialist (marine)
electrician.
If you are working on electrical systems, ensure that there is somebody
close at hand who can help you in emergencies.
!
WARNING!
Always use an adequate fuse in the positive line between the device
and the battery.
Make sure that the lead has a sufficient cross-section.
Lay the cables so that they cannot be damaged by the doors or the
bonnet.
Crushed cables can lead to serious injury.
!
CAUTION!
Lay the cables so that they cannot be tripped over or damaged.
DC08-40-DCD08-40--IO-16s.book Seite 8 Donnerstag, 28. Juli 2016 2:37 14
EN
PerfectCharge/PerfectPower General safety instructions
9
A
NOTICE!
Use ductwork or cable ducts if it is necessary to lay cables through
metal panels or other panels with sharp edges.
Do not lay the 230 V mains cable and the 12 V DC cable in the same
duct.
Do not lay the cable so that it is loose or heavily kinked.
Fasten the cables securely.
Do not pull on the cables.
2.4 Operating the device safely
!
WARNING!
Only use the device in closed, well-ventilated rooms.
Do not operate the device in systems with lead acid batteries. These
batteries give off explosive hydrogen gas that can be ignited by sparks
on electrical connections.
!
CAUTION!
Do not operate the device
In salty, wet or damp environments
In the vicinity of corrosive fumes
In the vicinity of combustible materials
In areas where there is a danger of explosions.
Before starting the device, ensure that the power supply lines are dry.
Always disconnect the power supply when working on the device.
Please observe that parts of the device may still conduct voltage even
if the fuse has blown.
Do not disconnect any cables when the device is still in use.
A
NOTICE!
Make sure the air inlets and outlets of the device are not covered.
Ensure good ventilation.
DC08-40-DCD08-40--IO-16s.book Seite 9 Donnerstag, 28. Juli 2016 2:37 14
EN
General safety instructions PerfectCharge/PerfectPower
10
2.5 Safety precautions when handling batteries
!
WARNING!
Batteries contain aggressive and caustic acids. Avoid battery fluid
coming into contact with your body. If your skin does come into
contact with battery fluid, wash the part of your body in question
thoroughly with water.
If you sustain any injuries from acids, contact a doctor immediately.
!
CAUTION!
When working on the batteries, do not wear any metal objects such as
watches or rings.
Lead acid batteries can cause short circuits which can cause serious
injuries.
Danger of explosions!
Never attempt to charge a frozen or defective battery.
Place the battery in a frost-free area and wait until the battery has accli-
matised to the ambient temperature. Then start the charging process.
Wear goggles and protective clothing when you work on batteries.
Do not touch your eyes when you are working on the battery.
Do not smoke and ensure that no sparks can arise in the vicinity of the
engine or battery.
A
NOTICE!
Only use rechargeable batteries.
Prevent any metal parts from falling on the battery. This can cause
sparks or short-circuit the battery and other electrical parts.
Make sure the polarity is correct when connecting the battery.
Follow the instructions of the battery manufacturer and those of the
manufacturer of the system or vehicle in which the battery is used.
If you need to remove the battery, first disconnect the earth
connection. Disconnect all connections and all consumers from the
battery before removing it.
DC08-40-DCD08-40--IO-16s.book Seite 10 Donnerstag, 28. Juli 2016 2:37 14
EN
PerfectCharge/PerfectPower Scope of delivery
11
3Scope of delivery
4Proper use
The transformers convert a g or 24 Vg supply from a car or boat battery to a stable
DC voltage:
DC08 (ref. no. 9600000095), DC20 (ref. no. 9600000096),
DC40 (ref. no. 9600000097): 12 Vg input voltage to 14.2 Vg output
voltage (charge converter)
DC40 eStore (ref. no. 9600000098): 12 Vg input voltage to 13.8 Vg
output voltage (charge converter)
DCDC10 (ref. no. 9600000084), DCDC20 (ref. no. 9600000086):
12 Vg input voltage to 27.6 Vg output voltage (voltage converter)
DCDC20 (ref. no. 9600000087), DCDC40 (ref. no. 9600000088):
24 Vg input voltage to 13.8 Vg output voltage (voltage converter)
DCDC10 (ref. no. 9600000085): 24 Vg input voltage to 27.6 Vg output
voltage (voltage converter)
All the converters can also be use to charge lead batteries.
A
The output voltage of the voltage converter is 13.8 V/27.6 V.
On charge converters, the output voltage follows an IU charging curve to a
maximum of 14.2 V (DC40 eStore: 13.8 V). This means the battery is charged
more quickly.
A
Quantity Description
1Converter
1 Operating manual
NOTICE!
Never use the device to charge other battery types (such as NiCd or
NiMH).
NOTICE!
Charge converter: Do not charge for longer than twelve hours.
DC08-40-DCD08-40--IO-16s.book Seite 11 Donnerstag, 28. Juli 2016 2:37 14
EN
Technical description PerfectCharge/PerfectPower
12
5 Technical description
The light weight and compact construction allows the converters to be easily
installed in mobile homes, commercial vehicles or motor and sailing vessels.
The transformers convert a 12 Vg or 24 Vg supply from a car or boat battery to a
stable 12 Vg or 24 Vg voltage for connecting to equipment.
The isolation of the input and output voltages means the output voltage can be kept
stable without interference from the input circuit.
Because the maximum output current is electronically regulated, the charge
converters can be used to charge batteries to generate electricity in cars or on boats.
The devices are equipped with protection against shorting and overloading. If the
protective function triggers, the device switches off and then switches on again
when correctly connected or when the load has been adequately reduced.
5.1 Control elements
No. in
fig. 1,
page 3
Explanation
1 Output terminals
2 “Power On” LED: There is voltage at the output terminals on the converter.
The converter is ready for use.
3 “Battery Low” LED: The input battery is no longer sufficiently charged.
4 “Overload” LED:
If a consumer is connected: The converter is shorted or overloaded.
If connected as a charger: The converter is in the full current charging
phase.
5 Air outlet
6 Main switch
7 Red: Positive cable to input battery
Black: Negative cable to input battery
8 Connection for switching on with on-board voltage (e.g. ignition or external
switch)
DC08-40-DCD08-40--IO-16s.book Seite 12 Donnerstag, 28. Juli 2016 2:37 14
EN
PerfectCharge/PerfectPower Mounting the converter
13
6Mounting the converter
6.1 Mounting instructions
If you wish to mount the converter in a fixed position, please observe the following
mounting instructions:
You can mount the device either horizontally or vertically.
Do not mount the device
In wet or damp environments
In the vicinity of combustible materials
In areas where there is a danger of explosions
The place of installation must be well-ventilated. A ventilation system must be
present for installations in small, closed spaces. The minimum clearance around
the device must be at least 5 cm (fig. 2, page 3).
The air intake on the underside or the air outlet on the back of the device must
remain clear.
For ambient temperatures higher than 40 °C (such as in engine or heating
compartments, or direct sunlight), the heat from the device under load can lead
to the automatic shut-down.
The installation surface must be level and sufficiently sturdy.
A
6.2 Mounting the converter
Hold the converter against the installation location and mark the fastening points
(fig. 3 A, page 3).
Fasten the converter using your chosen method (fig. 3 B, page 3).
NOTICE!
Before drilling any holes, ensure that no electrical cables or other parts
of the vehicle can be damaged by drilling, sawing and filing.
DC08-40-DCD08-40--IO-16s.book Seite 13 Donnerstag, 28. Juli 2016 2:37 14
EN
Connecting the converter PerfectCharge/PerfectPower
14
7 Connecting the converter
7.1 Connecting the input battery
!
A
Set the main switch (fig. 1 6, page 3) to “0”.
Lay the positive cable (red) (fig. 1 7, page 3) from the converter to positive
terminal of the battery and connect it.
Lay the negative cable (black) (fig. 1 7, page 3) from the converter to negative
terminal of the battery and connect it.
7.2 Connecting the connection cable
You can switch on the device as follows:
Using the main switch on the device (fig. 1 6, page 3)
Using the ignition (fig. 5 A, page 4)
Terminal 15: Connected positive terminal
Using an external switch (fig. 5 B, page 4)
Connecting the converter to be switched on via the main switch
Isolate the connecting line so no malfunction can occur.
Connecting the converter to be switched on via the ignition
Connect the connecting line to terminal 15 (connected positive terminal)
(fig. 5 A, page 4).
Set the main switch (fig. 1 6, page 3) on the back of the converter to “0”
permanently.
WARNING!
Do not reverse the polarity. Reverse polarity of the battery connections
can cause injury and irreversably damage the device.
NOTICE!
Tighten the nuts or bolts to a torque of 12 – 13 Nm. Loose connections
may cause overheating.
DC08-40-DCD08-40--IO-16s.book Seite 14 Donnerstag, 28. Juli 2016 2:37 14
EN
PerfectCharge/PerfectPower Connecting the converter
15
Connecting the converter to be switched on via an external switch
Connect the connecting line to an external switch (fig. 5 B, page 4).
Set the main switch (fig. 1 6, page 3) on the back of the converter to “0”
permanently.
7.3 Connecting power consuming devices to the
converter
Loosen the screw (fig. 4 2, page 4) from the positive terminal (red) (fig. 4 4,
page 4).
Push the cable lug (fig. 4 3, page 4) of the positive cable of the power consum-
ing device into the positive terminal (red) (fig. 4 4, page 4) and attach it using
the screw (fig. 4 2, page 4) and the spring washer (fig. 4 1, page 4).
Connect the negative cable of the power consuming device in the same way to
the negative terminal (black) (fig. 4 4, page 4).
DC08-40-DCD08-40--IO-16s.book Seite 15 Donnerstag, 28. Juli 2016 2:37 14
EN
Using the converter PerfectCharge/PerfectPower
16
8Using the converter
You can switch on the device as follows, depending on the connection:
Using the main switch on the device (fig. 1 6, page 3)
Using the ignition (fig. 5 A, page 4)
Terminal 15: Connected positive terminal
Using an external switch (fig. 5 B, page 4)
Switching on the converter
Set the main switch (fig. 1 6, page 3) on the back of the converter to “1” …
… or start the ignition …
… or push the external switch.
The LEDs (fig. 1 3 to 5, page 3) indicate the operating status:
I
LED Colour Explanation
Power On Green The device is switched on and there is voltage at
the output terminals on the converter. The
converter is ready for use.
Battery Low Yellow The input battery is no longer sufficiently
charged.
Recharge the battery or use a charged
battery.
Overload Red
If a consumer is connected:
The converter is shorted or overloaded.
Eliminate the short circuit or reduce the
output load.
If connected as a charger:
The converter is in the full current charging
phase.
NOTE
The internal fan is operated according to the temperature. It only runs
when the temperature is too high. During this time the converter is
switched off to prevent overheating.
DC08-40-DCD08-40--IO-16s.book Seite 16 Donnerstag, 28. Juli 2016 2:37 14
EN
PerfectCharge/PerfectPower Cleaning and caring for the converter
17
Switching off the converter
Set the main switch (fig. 1 6, page 3) on the back of the converter to “0” …
… or switch off the ignition …
… or push the external switch.
9 Cleaning and caring for the converter
A
Occasionally clean the device with a damp cloth.
10 Guarantee
The statutory warranty period applies. If the product is defective, please contact the
manufacturer's branch in your country (see the back of the instruction manual for the
addresses) or your retailer.
For repair and guarantee processing, please include the following documents when
you send in the device:
A copy of the receipt with purchasing date
A reason for the claim or description of the fault
11 Disposal
Place the packaging material in the appropriate recycling waste bins wherever
possible.
M
If you wish to finally dispose of the product, ask your local recycling centre
or specialist dealer for details about how to do this in accordance with the
applicable disposal regulations.
NOTICE! Danger of damaging the device!
Never clean the device under running water or in dish water.
Do not use abrasive cleaning agents or hard objects during cleaning as
these can damage the device.
DC08-40-DCD08-40--IO-16s.book Seite 17 Donnerstag, 28. Juli 2016 2:37 14
EN
Technical data PerfectCharge/PerfectPower
18
12 Technical data
DCDC10 DCDC20
Reference no.: 9600000084 9600000086
Transformation: 12 V 24 V
Rated input voltage: 12 Vg
Input voltage range: 8 V – 16 V
Output current: 10 A 20 A
Output voltage: 27.6 V ± 0.1 V
Efficiency up to: 87 %
Interference suppression: 40 mA
Ambient temperature for operation: –20 °C to +50 °C
Dimensions W x D x H: 140 x 115 x 70 mm 240 x 115 x 70 mm
Weight: 1.0 kg 1.9 kg
DCDC20 DCDC40
Reference no.: 9600000087 9600000088
Transformation: 24 V 12 V
Rated input voltage: 24 Vg
Input voltage range: 20 V – 32 V
Output current: 20 A 40 A
Output voltage: 13.8 V ± 0.1 V
Efficiency up to: 87 %
Interference suppression: 20 mA
Ambient temperature for operation: –20 °C to +50 °C
Dimensions W x D x H: 140 x 115 x 70 mm 240 x 115 x 70 mm
Weight: 1.0 kg 1.9 kg
DC08-40-DCD08-40--IO-16s.book Seite 18 Donnerstag, 28. Juli 2016 2:37 14
EN
PerfectCharge/PerfectPower Technical data
19
Certification
DC08 DC20 DC40
Reference no.: 9600000095 9600000096 9600000097
Transformation: 12 V 12 V
Rated input voltage: 12 Vg
Input voltage range: 8 V – 16 V
Output current: 8 A 20 A 40 A
Output voltage: 14.2 V ± 0.1 V
Efficiency up to: 87 %
Interference suppression: 20 mA
Ambient temperature for operation: –20 °C to +50 °C
Dimensions W x D x H: 100 x 115 x 70 mm 160 x 115 x 70 mm 270 x 115 x 70 mm
Weight: 0.75 kg 1.2 kg 2.1 kg
DCDC10 DC40 eStore
Reference no.: 9600000085 9600000098
Transformation: 24 V 24 V 12 V 12 V
Rated input voltage: 24 Vg 12 Vg
Input voltage range: 20 V – 32 V 8 V – 16 V
Output current: 10 A 40 A
Output voltage: 27.6 V ± 0.1 V 13.8 V ± 0.1 V
Efficiency up to: 87 % 87 %
Interference suppression: 40 mA 20 mA
Ambient temperature for operation: –20 °C to +50 °C –20 °C to +50 °C
Dimensions W x D x H: 140 x 115 x 70 mm 270 x 115 x 70 mm
Weight: 1.0 kg 2,1 kg
24
DC08-40-DCD08-40--IO-16s.book Seite 19 Donnerstag, 28. Juli 2016 2:37 14
DE
PerfectCharge/PerfectPower
20
Bitte lesen Sie diese Anleitung vor Einbau und Inbetriebnahme sorgfältig
durch und bewahren Sie sie auf. Geben Sie sie im Falle einer Weitergabe
des Produktes an den Nutzer weiter.
Inhaltsverzeichnis
1 Erklärung der Symbole . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
2 Allgemeine Sicherheitshinweise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
3 Lieferumfang . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
4 Bestimmungsgemäßer Gebrauch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
5 Technische Beschreibung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
6 Wandler montieren. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
7 Wandler anschließen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
8 Wandler benutzen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
9 Wandler pflegen und reinigen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
10 Gewährleistung. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
11 Entsorgung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
12 Technische Daten . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
DC08-40-DCD08-40--IO-16s.book Seite 20 Donnerstag, 28. Juli 2016 2:37 14
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229
  • Page 230 230
  • Page 231 231
  • Page 232 232
  • Page 233 233
  • Page 234 234
  • Page 235 235
  • Page 236 236
  • Page 237 237
  • Page 238 238
  • Page 239 239
  • Page 240 240
  • Page 241 241
  • Page 242 242
  • Page 243 243
  • Page 244 244
  • Page 245 245
  • Page 246 246
  • Page 247 247
  • Page 248 248
  • Page 249 249
  • Page 250 250
  • Page 251 251
  • Page 252 252
  • Page 253 253
  • Page 254 254
  • Page 255 255
  • Page 256 256

Dometic PerfectCharge DC 08 eStore Návod na používanie

Typ
Návod na používanie