Not for
Reproduction
BRIGGS & STRATTON CORPORATION
MILWAUKEE, WISCONSIN, U.S.A.
Manual No. 80015628 Rev C
020596-02
BPW4000
Copyright © 2018. Briggs & Stratton Corporation
Milwaukee, WI, USA. All rights reserved.
en - English
ar -
da - Dansk
es - Español
fi - Suomi
fr - Français
hu - Magyar
nl - Nederlands
no - Norsk
pl - Polski
ru -
sv - Svenska
sw - Kiswahili
Not for
Reproduction
2 BRIGGSandSTRATTON.COM
C
B
A
7
D
C
B
A
10
8
5
80010441
1
B
A
2
B
A
3
A
6
E A B C D
9
E
Not for
Reproduction
3
L
A
C
V
R
M
U
T
K
S
D
B
J
G
4
Q
P
N
E
F
H
Not for
Reproduction
4 BRIGGSandSTRATTON.COM
Safety and Control Symbols ................... 4
Equipment Description........................ 5
Assembly................................... 5
Features and Controls ........................ 5
Operation................................... 5
Maintenance ................................ 8
Storage .................................... 9
Troubleshooting ............................10
Specifications ..............................10
Warranty ..................................11
The safety alert symbol indicates a potential personal injury
hazard. A safety symbol may be used to represent the
type of hazard. WARNING indicates a hazard which, if not
avoided, could result in death or serious injury. CAUTION
indicates a hazard which, if not avoided, could result in
minor or moderate injury. NOTICE indicates information
considered important, but not hazard-related.
This machine is not intended for use by persons
(including children) with reduced physical,
sensory or mental capabilities, or lack of
experience and knowledge, unless supervised
and given instruction concerning safe operation
and understanding of hazards involved.
WARNING!
• This machine has been designed for use with
the cleaning agent supplied or recommended
by the manufacturer. The use of other cleaning
agents or chemicals may adversely affect the
safety of the machine.
• High pressure jets can be dangerous if subject to
misuse. The jet must not be directed at persons,
live electrical equipment or the machine itself.
• Do not use the machine within range of persons
unless they wear protective clothing.
• Do not direct the jet against yourself or others
in order to clean clothes or foot-wear.
• Risk of explosion – Do not spray flammable liquids.
• High pressure cleaners shall not be used by
children or untrained personnel.
• High pressure hoses, fittings and couplings
are important for the safety of the machine.
Use only hoses, fittings and couplings
recommended by the manufacturer.
• To ensure machine safety, use only original
spare parts from the manufacturer or approved
by the manufacturer
• Water that has flown through backflow
preventers is considered to be non-potable.
• Do not use the machine if important parts of the
machine are damaged, e.g. safety devices, high
pressure hoses, trigger gun.
• Where no ignition key and no battery exist, the
disconnection can be acheived by equivalent means.
• Do not use combustion engine powered
machines indoors unless adequate ventilation is
assessed by national labour authorities.
• Ensure that any exhaust emissions are not in
the vicinity of air intakes.
• Incorrect fuels shall not be used as they may
prove hazardous.
• Throttle control lever shall be in STOP (
)
position during cleaning or maintenance and
when replacing parts.
For questions regarding European emissions, please
contact our European office at:
Never spray yourself, others, animals, power
sources, or the unit itself.
Stop
Fire
Explosion
Toxic Fumes
Moving Parts
Fall
Kickback
Flying Objects
Fluid Injection
Instruction
Manual
Chemical Burn
Projectile
Electrical Shock
Fast
Safety Alert
Symbol
Fuel Off
Choke Run
Slow
Check Oil
Level
Fuel On
Do Not Start
Engine
!
Hot Surface
Non-Potable
Water
Not for
Reproduction
5
Warning Tag Figure
1
A warning tag is provided on your unit to inform you of
potential safety hazards. If the tag becomes damaged
or illegible, replace it by contacting your local Briggs &
Stratton dealer to obtain a new one.
This pressure washer operates at 27.6 MPa (276 BAR or 4,000
PSI) and a flow rate of 15.14 liters (4.0 gallons) per minute. This
high quality residential system features 30.5 cm (12”) wheels,
triplex pump with stainless steel pistons, automatic cool down
system, detergent siphoning system, quick connect spray tips,
heavy duty 15.24 m (50’) hose, and more.
Every effort has been made to ensure that information in
this manual is accurate and current. However, we reserve
the right to change, alter, or otherwise improve the product
and this document at any time without prior notice.
NOTICE If you have questions about intended use, ask
dealer or contact qualified service center. NEVER operate
units with broken or missing parts, or without protective
housing or covers. DO NOT by-pass any safety device
on this machine. DO NOT modify pressure washer in any
way. This equipment is designed to be used with Briggs &
Stratton Corporation authorized parts ONLY.
When transporting equipment with a vehicle or trailer,
EMPTY fuel tank or turn fuel shutoff valve, if equipped, to
OFF (0) position. DO NOT tip engine or equipment at angle
which causes fuel to spill.
Assembly
Figure
2
3
1. Place handle (2, A) onto supports (2, B) and align
holes.
2. Insert carriage bolts (3, A) through holes from inside
of unit, attach with plastic knobs (3, B) and tighten.
Figure
4
Oil
Figure
5
We recommend the use of Briggs & Stratton Warranty
Certified oils for best performance. Other high-quality
detergent oils are acceptable if classified for service SF,
SG, SH, SJ or higher. DO NOT use special additives.
Outdoor temperatures determine the proper oil viscosity for
the engine. Use the chart to select the best viscosity for the
outdoor temperature range expected.
* Below 4°C (40°F) the use of SAE 30 will result in hard starting.
** Above 27°C (80°F) the use of 10W30 may cause increased oil
consumption. Check oil level more frequently.
Checking/Adding Engine Oil Figure
6
Oil level should be checked prior to each use or at least
every 8 hours of operation. Keep oil level maintained.
1. Make sure pressure washer is on a level surface.
2. Clean area around oil fill, remove oil cap/dipstick and
wipe clean. Insert dipstick, DO NOT screw in. Remove
and check oil level.
3. Verify oil is at FULL mark (A) on dipstick.
4. If needed, slowly pour oil into oil fill opening to FULL
mark on dipstick. Pause to permit oil to settle. DO
NOT overfill.
5. Replace and tighten oil cap/dipstick.
NOTICE DO NOT attempt to crank or start engine before
before it has been properly serviced with recommended oil.
This could result in an engine failure.
CAUTION Avoid prolonged or repeated skin contact with
used motor oil. Used motor oil has been shown to cause
skin cancer in certain laboratory animals. Thoroughly wash
exposed areas with soap and water.
KEEP OUT OF REACH OF CHILDREN. DON’T
POLLUTE. CONSERVE RESOURCES. RETURN
USED OIL TO COLLECTION CENTERS.
Add Fuel Figure
7
• Clean, fresh, unleaded gasoline.
• A minimum of 87 octane/87 AKI (91 RON). For high
altitude use, see High Altitude.
• Gasoline with up to 10% ethanol (gasohol) is acceptable.
NOTICE Use of unapproved fuels could damage
pressure washer and voids warranty. DO NOT use
unapproved gasoline such as E15 and E85. DO NOT mix
oil in gasoline or modify engine to run on alternate fuels.
To protect the fuel system from gum formation, mix in a
fuel stabilizer when adding fuel. See Storage. All fuel is
not the same. If you experience starting or performance
problems after using fuel, switch to a different fuel provider
or change brands. This engine is certified to operate on
gasoline. The emission control system for this engine is
EM (Engine Modifications).
A Fuel Tank L
Detergent Siphoning Tube
B Air Filter M High Pressure Outlet
C Throttle Lever N Identification Label
D Choke Lever P Oil Drain
E
Fuel Lever
Q Oil Fill
F Recoil Starter R Warning Tag
G Pump S High Pressure Hose
H Pressure Control
Knob
T Nozzle Extension with
Quick Connect
J Automatic Cool Down
System
U Spray Tips
K Water Inlet V Spray Gun
Not for
Reproduction
6 BRIGGSandSTRATTON.COM
WARNING! Fuel and its vapors are
extremely flammable and explosive which
could cause burns, fire or explosion resulting in death or
serious injury. Turn pressure washer engine off and let it
cool at least 2 minutes before removing fuel cap. Loosen
cap slowly to relieve pressure in tank. Fill fuel tank
outdoors. DO NOT overfill tank. Allow space for fuel
expansion. If fuel spills, wait until it evaporates before
starting engine. Keep fuel away from sparks, open flames,
pilot lights, heat, and other ignition sources. Check fuel
lines, tank, cap and fittings frequently for cracks or leaks.
Replace if necessary. DO NOT light a cigarette or smoke.
1. Clean area around fuel fill cap, remove cap.
2. Slowly add regular unleaded fuel (A) to fuel tank (B).
Be careful not to overfill. Allow about 4 cm (1.5”) (C) of
tank space for fuel expansion.
3. Install fuel cap and let any spilled fuel evaporate
before starting engine.
At altitudes over 1524 m (5,000 ft.), a minimum 85 octane
/ 85 AKI (89 RON) gasoline is acceptable. To remain
emissions compliant, high altitude adjustment is required.
Operation without this adjustment will cause decreased
performance, increased fuel consumption, and increased
emissions. See an Authorized Briggs & Stratton dealer
for high altitude adjustment information. Operation of the
engine at altitudes below 762 m (2,500 ft.) with the high
altitude kit is not recommended.
Figure
8
Carbon Monoxide Poisoning
WARNING! Engine exhaust contains carbon
monoxide, a poisonous gas that could kill you in
minutes. You CANNOT smell it, see it, or taste it. Even if you do
not smell exhaust fumes, you could still be exposed to carbon
monoxide gas. Operate this product ONLY outside far away
from windows, doors and vents to reduce the risk of carbon
monoxide gas from accumulating and potentially being
drawn towards occupied spaces. Install battery-operated
carbon monoxide alarms or plug-in carbon monoxide
alarms with battery back-up according to the
manufacturer’s instructions. Smoke alarms cannot detect
carbon monoxide gas. DO NOT run this product inside
homes, garages, basements, crawlspaces, sheds, or other
partially-enclosed spaces even if using fans or opening
doors and windows for ventilation. Carbon monoxide can
quickly build up in these spaces and can linger for hours,
even after this product has shut off. ALWAYS place this
product downwind and point the engine exhaust away from
occupied spaces. If you start to feel sick, dizzy, or weak
while using this product, get to fresh air RIGHT AWAY. See
a doctor. You may have carbon monoxide poisoning.
Risk of Fire Clearances
WARNING! Exhaust heat/gases could ignite
combustibles, structures or damage fuel tank causing
a fire, resulting in death or serious injury. Keep at least 1.5
m (5 ft.) clearance on all sides of pressure washer
including overhead.
Figure
4
NOTICE Inspect high pressure hose for cuts, leaks or damage.
1. Pull back on collar of high pressure hose (S), slide onto
spray gun (V) and release collar. Tug on hose to make
sure it is secure.
2. Pull back collar on other end of hose and slide onto
outlet (M) on pump and release collar. Tug on hose to
make sure it is secure.
3. Inspect inlet screen before connecting garden hose
to water inlet (K). Clean screen if it contains debris or
replace if damaged. DO NOT run pressure washer if
inlet screen is damaged.
4. Make sure water source is capable of supplying water
at a flow rate greater than 18.9 liters (5.0 gallons) per
minute and 0.14-0.55 MPa (1.4-5.5 BAR or 20-80 PSI)
at pressure washer end of garden hose.
5. Run water through garden hose to clean out debris.
NOTICE Use ONLY cold water (less than 38°C (100°F)).
NOTICE Using a backflow preventer at pump inlet could
cause pump damage. There MUST be at least 3 m (10 ft.)
of unrestricted garden hose between pressure washer inlet
and backflow preventer.
WARNING! Water that has flowed through a
backflow preventer is considered to be non-potable.
6. Connect garden hose (not to exceed 15 m (50 ft.)) to
water inlet and tighten.
7. Turn ON water, press red button on gun, and squeeze trigger
to purge system of air. Replace gun if trigger does not lock.
8. Attach nozzle extension (T) to gun (V) and tighten.
9. Pull back on collar of nozzle extension, insert spray
tip (U) and release. Tug on spray tip to make sure it is
securely in place.
Figure
4
NOTICE DO NOT run pump without water supply
connected and turned on.
1. Move fuel lever (E) to ON ( ) position.
2. Move throttle control lever (C) to FAST ( ) position,
shown on engine as a rabbit.
3. Move choke lever (D) to CHOKE ( ) position.
NOTICE For a warm engine, be sure choke lever is in
RUN ( ) position.
WARNING! Starter and other rotating parts could
entangle hands, hair, clothing, or accessories resulting
in serious injury. NEVER operate pressure washer without
protective housing or covers. DO NOT wear loose clothing,
jewelry or anything that could be caught in the starter or other
rotating parts. Tie up long hair and remove jewelry.
WARNING! Spray could splash back or
propel objects resulting in serious injury. Always
wear indirect vented (chemical splash) safety goggles marked
to comply with EN166 when using or in vicinity of this
equipment. Always wear protective clothing such as a long-
sleeved shirt, long pants and close-toed shoes.
Not for
Reproduction
7
4. When starting engine, grasp recoil handle and pull
slowly until you feel some resistance. Then pull rapidly
to start engine.
WARNING! Starter cord kickback (rapid retraction)
will pull hand and arm toward engine faster than you
can let go which could cause broken bones, fractures,
bruises, or sprains resulting in serious injury. NEVER pull
starter cord without first relieving spray gun pressure.
When starting engine, pull cord slowly until resistance is
felt and then pull rapidly to avoid kickback. Firmly grasp
spray gun with both hands when using high pressure spray
to avoid injury when spray gun kicks back.
5. Return recoil handle slowly. DO NOT let rope “snap
back” against starter.
6. After each starting attempt, where engine fails to
run, point gun in safe direction, press red button and
squeeze trigger to release high pressure.
7. When engine starts, slowly move choke lever to RUN ( )
position, as engine warms. If engine falters, move choke
lever to CHOKE ( ) position, then to RUN ( ) position.
NOTICE Always keep throttle lever in FAST ( ) position
when operating pressure washer.
WARNING! The high pressure stream of water that
this equipment produces could cut through skin and
its underlying tissues, resulting in serious injury and
possible amputation. If cut by fluid, call physician
immediately. DO NOT treat as a simple cut. DO NOT allow
CHILDREN to play with or operate pressure washer.
NEVER aim spray gun at people, animals, or plants. DO
NOT secure spray gun in open position. DO NOT leave
spray gun unattended while machine is running. NEVER
use a spray gun which does not have a trigger lock or
trigger guard in place and in working order. NEVER
connect high pressure hose to nozzle extension.
WARNING! Contact with muffler area could cause
burns resulting in serious injury. DO NOT touch hot
parts and AVOID hot exhaust gases. Allow equipment to
cool before touching.
WARNING! Contact with power source could
cause electric shock or burn resulting in death or
serious injury. NEVER spray near power source.
Spray Tips Figure
9
Spray tips can be changed while pressure washer is
running once spray gun trigger is locked.
1. Pull back collar on quick–connect and pull current spray tip
off. Store spray tips in holes provided on accessory tray.
2. Select desired spray tip:
• For delicate rinse, select white 40° (A) or green
25° (B) spray tip.
• For general rinsing, select yellow 15° (C) spray tip.
• For maximum rinsing, select red 0° (D) spray tip.
• To apply detergent, select black (E) detergent spray tip.
3. Pull back on collar, insert new spray tip and release
collar. Tug on spray tip to make sure it is secure.
Usage Tips
• For most effective cleaning, keep spray tip from 20 to 61
cm (8 to 24 inches) away from cleaning surface.
• If you get spray tip too close, especially using a high
pressure spray tip, you may damage surface being
cleaned.
• DO NOT get closer than 15 cm (6 inches) when
cleaning tires.
WARNING! Chemicals could cause burns resulting
in death or serious injury. DO NOT use caustic liquid
with pressure washer. Use ONLY pressure washer safe
detergents/soaps. Follow manufacturers instructions.
1. Place detergent siphoning tube into detergent container.
2. Install black detergent spray tip.
NOTICE Detergent cannot be applied with high pressure
spray tips (White, Green, Yellow or Red).
3. Apply detergent to a dry surface, starting at lower
portion of area to be washed and work upward, using
long, even, overlapping strokes.
4. Allow detergent to “soak in” per detergent
manufacturer’s instructions before washing and rinsing.
NOTICE Flush detergent siphoning system after each
use by placing tube into a bucket of clean water, then run
pressure washer with black spray tip for 1-2 minutes.
Pressure Washer Rinsing Figure
4
1. Remove black detergent spray tip from nozzle
extension.
2. Select and install high pressure spray tip.
WARNING! Kickback from spray gun (43 N) could
cause you to fall resulting in death or serious injury.
Operate pressure washer from a stable surface. Be
extremely careful if you must use the pressure washer from
a ladder, scaffolding, or any other similar location. Firmly
grasp spray gun with both hands when using high pressure
spray to avoid injury when spray gun kicks back.
3. Increase (decrease) spray pressure by
turning pressure control knob (H) clockwise
(counterclockwise). Use lower pressure to wash items
such as a car or boat. Use higher pressure to strip
paint and degrease driveways.
4. Apply a high pressure spray to a small area and check
surface for damage. If no damage is found, continue
rinsing.
5. Start at top of area to be rinsed, working down with
same overlapping strokes as you used for cleaning.
Relief)
Circulating water in pump can reach temperatures above
51°C (125°F) if running pressure washer for 3-5 minutes
without pressing trigger on gun. The system engages to
cool pump by
Not for
Reproduction
8 BRIGGSandSTRATTON.COM
1. Release spray gun trigger and let engine idle for two
minutes.
2. Move throttle to SLOW ( ) position, then STOP ( )
position.
3. Move fuel lever to OFF ( ) position.
4. ALWAYS point spray gun in safe direction, press red
button and squeeze spray gun trigger to release high
pressure, every time you stop engine.
WARNING!
Spray gun traps high water pressure,
even when engine is stopped and water is
disconnected, which could result in serious injury.
Keep high
pressure hose connected to pump and spray gun while
system is pressurized. ALWAYS point spray gun in safe
direction, press red button and squeeze spray gun trigger to
release high pressure, every time you stop engine.
Water should not remain in the unit for long periods of time.
Sediments or minerals can deposit on pump parts and
freeze pump action. Follow these procedures after every
use:
1. Turn off water supply, and let engine cool.
2. Disconnect hose from gun and outlet on pump. Drain
water from hose, gun, and nozzle extension.
3. Place spray tips and hose on accessory tray. Place
spray gun and nozzle extension in wireform.
4. Empty pump of all liquids by pulling recoil handle
about six times.
5. Store unit in a clean, dry area.
NOTICE If storing for more than 30 days, see Storage.
WARNING! Fuel and its vapors are
extremely flammable and explosive which
could cause burns, fire or explosion resulting in death or
serious injury. When storing fuel or equipment with fuel in
tank, store away from furnaces, stoves, water heaters,
clothes dryers, or other appliances that have pilot light or
other ignition source because they could ignite fuel vapors.
Follow hourly or calendar intervals, whichever occurs
first. More frequent service is required when operating in
adverse conditions.
1
Service more often under dirty or dusty conditions.
3
Change pump oil after the first (50) operating hours and then every
200 hours or 3 months thereafter.
Regular maintenance will improve performance and extend
the life of the pressure washer. See any Briggs & Stratton
Authorized Service Dealer for service. DO NOT allow
children to clean or maintain without supervision.
The pressure washer’s warranty does not cover items that
have been subjected to operator abuse or negligence. To
receive full value from warranty, operator must maintain
pressure washer as instructed in this manual, including
proper storage as detailed in Storage.
WARNING! To ensure machine safety, use only
original spare parts from the manufacturer or approved by
the manufacturer. Should you have questions about
replacing components on your pressure washer, please
visit our website at BRIGGSandSTRATTON.COM.
• Change engine oil
Every 8 Hours or Daily
• Clean debris
• Check engine oil level
Every 25 Hours or Yearly
• Service engine air cleaner
1
Every 50 Hours or Yearly
• Change engine oil
1
• Inspect muffler
Every 100 Hours or Yearly
• Service spark plug
• Clean cooling system
1
• Change pump oil
3
Not for
Reproduction
9
Occasionally check ball in detergent siphoning system may
become stuck from storage, dried soap, or minerals in water.
The check ball can be freed by performing the following:
1. Turn off water supply.
2. With engine off and pressure released from the
system, remove detergent siphoning hose from
barbed fitting on pump.
3. Using a firm, blunt object 2mm (7/64”) in diameter or
smaller, by at least 25.4mm (1”) long, such as an Allen
wrench, slowly insert object into barbed fitting until you
meet resistance. This resistance is the check ball.
4. Slowly push down until you feel ball move slightly,
push no more than 3mm (1/8”). Slight pressure may
be required to free ball.
5. Repeat steps 3 and 4 if necessary.
6. Reinstall detergent siphoning hose onto barb fitting.
7. Treat with PumpSaver as described in Protecting the
Pump during storage to prevent reoccurrence.
Figure
4
Clean spray tip to correct excessive pump pressure
caused by a clogged spray tip:
1. Turn off water supply.
2. Remove spray tip from end of nozzle extension.
3. Use a small paper clip to free any foreign material
clogging or restricting spray tip (U).
4. Reinstall spray tip into nozzle extension.
Figure
10
The use of a lubricant (petroleum or synthetic grease) helps
seat o-rings providing an improved seal. Apply lubricant
to o-rings prior to assembling garden hose to the pump
inlet (A), high pressure hose to pump outlet (B), high
pressure hose (C), spray gun (D), and nozzle extension (E).
Purchase an O-Ring Maintenance Kit by contacting a
Briggs & Stratton Authorized Service Dealer. Refer to the
instruction sheet provided in the kit to service your unit’s
o-rings. NEVER repair leaking connections with sealant of
any kind. Replace o-ring or seal.
Changing Pump Oil
NOTICE When changing pump oil, use only high quality
SAE 30 weight oil. Use no special additives.
1. Clean area around brass oil drain plug at bottom of pump.
2. Remove oil drain plug. Drain oil completely into an
approved container.
3. When oil has completely drained, install oil drain plug
and tighten firmly.
4. Clean area around pump oil dipstick. Remove dipstick
and fill pump with recommended oil (approximately
355 ml (12 oz.)) to “Full” mark on dipstick.
5. Install pump oil dipstick.
6. Wipe up any spilled oil.
If you do not plan to use the pressure washer for more than
30 days, you must prepare engine and pump for storage.
To protect pump from damage caused by mineral deposits
or freezing, use PumpSaver to prevent freeze damage and
lubricate pistons and seals.
NOTICE Failure to protect unit from freezing
temperatures will damage pump and render unit
inoperable. Freeze damage is not covered under warranty.
Fuel can become stale when stored over 30 days. Stale fuel
causes acid and gum deposits to form in the fuel system or
on essential carburetor parts.
There is no need to drain gasoline from the engine if a
fuel stabilizer is added according to instructions. Run the
engine for 2 minutes to circulate the stabilizer throughout
the fuel system before storage.
If gasoline in the engine has not been treated with a fuel
stabilizer, it must be drained into an approved container.
Run the engine until it stops from lack of fuel. The use of a
fuel stabilizer in the storage container is recommended to
maintain freshness.
1. DO NOT store fuel from one season to another unless it
has been treated as described in Protect Fuel System.
2. Cover unit with a suitable protective cover that does
not retain moisture.
WARNING! Storage covers could cause a fire
resulting in death or serious injury. DO NOT place a
storage cover over a hot pressure washer. Let equipment
cool for a sufficient time before placing the cover on the
equipment.
3. Store unit in a clean, dry area.
Not for
Reproduction
10 BRIGGSandSTRATTON.COM
Problem Cause
volume.
1. Low pressure spray tip installed.
2. Inadequate water supply.
3. Inlet hose is kinked or leaking.
4. Clogged inlet hose screen.
5. Water supply is over 38°C (100°F).
6. High pressure hose is blocked or
leaks.
7. Spray gun leaks.
8. Spray tip is obstructed.
1.
Replace with high pressure spray tip.
2. Provide adequate water flow.
3. Straighten inlet hose, patch leak.
4.
Check and clean inlet hose screen.
5. Provide cooler water supply.
6. Clear blocks in outlet hose, replace
if leaking.
7. Replace spray gun.
8. Clean spray tip.
spray.
1. Detergent siphoning tube is not
submerged.
2. Detergent siphoning tube is clogged or
cracked.
3. High pressure spray tip installed.
4. Check ball stuck in detergent siphoning
system.
1. Insert detergent siphoning tube into
detergent.
2. Clean or replace detergent
siphoning tube.
3. Replace with black spray tip.
4. Free detergent siphoning check ball.
Engine speed is too slow.
Move throttle control to FAST(
)
position.
and runs rough.
1. Low oil level.
2. Out of fuel.
3. Spark plug wire not connected to
spark plug.
4. Flooded.
1. Fill crankcase to proper level.
2. Fill fuel tank.
3. Connect wire to spark plug.
4. Wait 5 minutes and re-crank engine.
The gross power rating for individual gasoline engine models is labeled in accordance with SAE (Society of Automotive
Engineers) code J1940 Small Engine Power & Torque Rating Procedure, and is rated in accordance with SAE J1995. Torque values are
derived at 2600 RPM for those engines with “rpm” called out on the label and 3060 RPM for all others; horsepower values are derived at
3600 RPM. The gross power curves can be viewed at www.BRIGGSandSTRATTON.COM. Net power values are taken with exhaust and
air cleaner installed whereas gross power values are collected without these attachments. Actual gross engine power will be higher than net
engine power and is affected by, among other things, ambient operating conditions and engine-to-engine variability. Given the wide array
of products on which engines are placed, the gasoline engine may not develop the rated gross power when used in a given piece of power
equipment. This difference is due to a variety of factors including, but not limited to, the variety of engine components (air cleaner, exhaust,
charging, cooling, carburetor, fuel pump, etc.), application limitations, ambient operating conditions (temperature, humidity, altitude), and
engine-to engine variability. Due to manufacturing and capacity limitations, Briggs & Stratton may substitute an engine of higher rated
power for this engine.
* This pressure washer is rated in accordance to the Pressure Washer Manufacturers Association (PWMA) standard PW101-2010
(Testing and Rating Performance of Pressure Washers).
§
Measured sound values in accordance to Tasmanian Environmental Management and Pollution Control (Miscellaneous Noise)
Regulations.
Outlet Pressure ............27.6 MPa (276 BAR or 4,000 PSI)*
Flow Rate ........................15.1 liters/min (4.0 GPM)
Water Supply Temperature ................38ºC (100ºF) MAX
Displacement ........................ 420 cc (25.63 cu. in.)
Spark Plug Gap.........................0.76 mm (0.030 in.)
Fuel Capacity ............................6.6 liters (7.0 Qt.)
Oil Capacity..........................1.1 liters (37 Ounces)
Sound Pressure @ 3 m ...........................90 dBA
§
O-Ring Maintenance Kit............................705002
Water Inlet Screen ..............................B2384GS
Engine Oil Bottle .................................100005E
PumpSaver ........................................6039
Not for
Reproduction
11
80010169_EN Rev C
BRIGGS & STRATTON WARRANTY POLICY
LIMITED WARRANTY
Briggs & Stratton warrants that, during the warranty period specified below, it will repair or replace, free of charge, any part that is defective in material or
workmanship or both. Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser. This warranty is
effective for and is subject to the time periods and conditions stated below. For warranty service, find the nearest Authorized Service Dealer in our dealer locator
map at BRIGGSandSTRATTON.COM. The purchaser must contact the Authorized Service Dealer, and then make the product available to the Authorized
Service Dealer for inspection and testing.
.
Some states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries do not
allow the exclusion or limitation of incidental or consequential damages, so the above limitation and exclusion may not apply to you. This warranty gives you
specific legal rights and you may also have other rights which vary from state to state or country to country.**
WARRANTY PERIOD
* Applies to Briggs & Stratton engines only. Warranty coverage of non-Briggs & Stratton engines is provided by that engine manufacturer. Emissions-related
components are covered by the Emissions Warranty Statement.
** In Australia - Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a
major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods
fail to be of acceptable quality and the failure does not amount to a major failure. For warranty service, find the nearest Authorized Service Dealer in our dealer
locator map at BRIGGSandSTRATTON.COM, or by calling 1300 274 447, or by emailing or writing to [email protected], Briggs & Stratton
Australia Pty Ltd, 1 Moorebank Avenue, NSW, Australia, 2170.
The warranty period begins on the date of purchase by the first retail or commercial consumer. “Consumer use” means personal residential household use by a
retail consumer. “Commercial use” means all other uses, including use for commercial, income producing or rental purposes. Once a product has experienced
commercial use, it shall thereafter be considered as a commercial use product for purposes of this warranty.
Save your proof of purchase receipt. If you do not provide proof of the initial purchase date at the time warranty service is requested, the manufacturing date of the
product will be used to determine the warranty period. Product registration is not required to obtain warranty service on Briggs & Stratton products.
ABOUT YOUR WARRANTY
Warranty service is available only through Briggs & Stratton Authorized Service Dealers. This warranty covers only defects in materials or workmanship. It does not
cover damage caused by improper use or abuse, improper maintenance or repair, normal wear and tear, or stale or unapproved fuel.
Improper Use and Abuse - The proper, intended use of this product is described in the Operator’s Manual. Using the product in a way not described in the
Operator’s Manual or using the product after it has been damaged will not be covered under this warranty. Warranty coverage will also not be provided if the serial
number on the product has been removed or the product has been altered or modified in any way, or if the product has evidence of abuse such as impact damage
or water/chemical corrosion damage.
- This product must be maintained according to the procedures and schedules provided in the Operator’s Manual, and serviced
or repaired using genuine Briggs & Stratton parts or equivalent. Damage caused by lack of maintenance or use of non-original parts is not covered by warranty.
Normal Wear and Tear - Like most mechanical devices, your unit is subject to wear even when properly maintained. This warranty does not cover repairs when
normal use has exhausted the life of a part or the equipment. Maintenance and wear items such as filters, belts, cutting blades, and brake pads (except engine
brake pads) are not covered by warranty due to wear characteristics alone, unless the cause is due to defects in material or workmanship.
- In order to function correctly, this product requires fresh fuel that conforms to the criteria specified in the Operator’s Manual. Engine or
equipment damage caused by stale fuel or the use of unapproved fuels (such as E15 or E85 ethanol blends) is not covered by warranty.
This warranty excludes damage due to accident, abuse, modifications, alterations, improper servicing, freezing or chemical deterioration.
Attachments or accessories that were not originally packaged with the product are also excluded. There is no warranty coverage on equipment used for
primary power in place of utility power or on equipment used in life support applications. This warranty does not include used, reconditioned, second-hand, or
demonstration equipment or engines. This warranty also excludes failures due to acts of God and other force majeure events beyond the manufacturer’s control.
Consumer Use Commercial Use
Equipment 24 months 3 months
Engine* 24 months 3 months
Battery (if equipped) 3 months None
Not for
Reproduction
4.00027.6
4.014.14BAR 276
1230.5
5012.54
. Briggs & Stratton
0
3
2
B ,2A ,2 1
A ,3 2
B ,3
4
5
Briggs & Stratton
SJSGSF
SAE404°
8027
10W 30
6
8
1
2
AFULL 3
4
FULL
5
7
(91 RON) 87 AKI87
.
%10
E85E15
EM
2
1
BA 2
C1.54
3
5,000
1524
(89 RON) 85 AKI 85
Briggs &
Stratton
2,500
762
5
AL
BM
CN
DP
EQ
FR
GS
HT
JU
KV
Not for
Reproduction
4. . . . . . . . . . . . . . . . . . . . . . . . .
5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5. . . . . . . . . . . . . . . . . . . . . . . . . . .
5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10. . . . . . . . . . . . . . . . . . . . . . . .
10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
•
1
Briggs & Stratton
BRIGGSandSTRATTON.COM 4
!
Not for
Reproduction
9
1
2
A) 40°
.(B) 25°
.(C15
.(D) 0
.(E
3
2486120
615 •
1
2
3
4
1-2
4
1
2
(N 43
H 3
4
5
51
3-5125
.
1
STOP
SLOW 2
.(
.(
OFF 3
4
1
2
3
4
5
.30
7
Not for
Reproduction
8
51.5
4
,(S 1
V
M
2
.(K 3
4
0.14-0.555.018.9
BAR 1.4-5.520-80
5
10038°
103
15 6
50)
7
T V 8
(U 9
4
.( ) ONE1
( C) FAST 2
.( D) CHOKE 3
.( RUN
EN166
4
5
6
7
RUN
CHOKE
.( RUN
FAST
)
BRIGGSandSTRATTON.COM 6
Not for
Reproduction
9
30
30
1
.
2
3
Not for
Reproduction
BRIGGSandSTRATTON.COM 8
1
20050
3
3
Briggs & Stratton
.
.BRIGGSandSTRATTON.COM
1
2
7/642 3
125.4
4
1/83
43 5
6
7
4
1
2
.(U 3
4
10
BA
.(EDC
Briggs & Stratton
SAE 30
1
2
3
4
12355
Full
5
6
5
8
25
1
250
1
100
1
3200
3
Not for
Reproduction
11
AR Rev C_80010169
BRIGGS & STRATTON
Briggs & Stratton
.BRIGGSandSTRATTON.COM
**
Briggs & Stratton Briggs & Stratton *
**
[email protected]
1300 274 447 BRIGGSandSTRATTON.COM
.Briggs & Stratton Australia Pty Ltd, 1 Moorebank Avenue, NSW, Australia, 2170
.Briggs & Stratton
.Briggs & Stratton
-
Briggs & Stratton
-
-
-
( E15 E85 )
-
24 3
24 3
3
Not for
Reproduction
BRIGGSandSTRATTON.COM 10
1
2
3
4
38° 5
100°
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
1
2
3
4
.(
FAST
1
2
3
4
1
2
3
5 4
.
SAE) J1940
2600J1995
36003060
www.BRIGGSandSTRATTON.COM
Briggs & Stratton
2010PW101PWMA
§
*(BAR 2764,00027.6. . . . . . . . . . . . . . . .
4.015.1. . . . . . . . . . . . . . . . . . . . . . .
100º38º . . . . . . . . . . . . . . . .
25.63420. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0.0300.76. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.06.6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
371.1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
§
90 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
705002 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B2384GS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
100005E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6039 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Not for
Reproduction
4 BRIGGSandSTRATTON.COM4 BRIGGSandSTRATTON.COM
........... 4
.................. 5
................................ 5
...................... 5
.............................. 5
..................... 8
................................ 9
.............10
.............................10
.................................11
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
(
1
!
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
/