Makita GA042G Používateľská príručka

GA042G

GA043G

GA044G

GA045G

GA046G

GA047G

EN Cordless Angle Grinder INSTRUCTION MANUAL 9

PL Akumulatorowa szlierka

kątowa INSTRUKCJA OBSŁUGI 25

HU Akkumulátoros sarokcsiszoló HASZNÁLATI KÉZIKÖNYV 43

SK Ručná uhlová brúska NÁVOD NA OBSLUHU 61

CS Akumulátorová úhlová

bruska NÁVOD K OBSLUZE 78

UK Бездротова кутова

шліфувальна машина ІНСТРУКЦІЯ З

ЕКСПЛУАТАЦІЇ 95

RO Polizor unghiular cu

acumulator MANUAL DE INSTRUCŢIUNI 114

DE Akku-Winkelschleifer BETRIEBSANLEITUNG 132

2

3

1

Fig.1

1

2

Fig.2

1 2

Fig.3

1

Fig.4

Fig.5

3

2

1

Fig.6

3

2

B

1

A

B

Fig.7

2

1

A

C

Fig.8

1

2

Fig.9

1

2

Fig.10

Fig.11

1

Fig.12

4

1

2

Fig.13

1

2

A

B

Fig.14

2

4

3

1

Fig.15

1

2

Fig.16

1

A

B

Fig.17

Fig.18

1

2

Fig.19

5

15°

Fig.20

Fig.21

Fig.22

Fig.23

Fig.24

Fig.25

1

Fig.26

1

4

2

3

Fig.27

6

23

1

Fig.28

1

Fig.29

1

2

Fig.30

Fig.31

1

Fig.32

7

1

2

Fig.33

1

Fig.34

1

Fig.35

1

2

Fig.36

1

2

Fig.37

1

Fig.38

8

2

6

7

4

5

2

8

10

9

3

1

Fig.39

9ENGLISH

ENGLISH (Original instructions)

SPECIFICATIONS

Model: GA042G GA043G GA044G GA045G GA046G GA047G

Applicable grinding wheel Max. wheel diameter 100 mm 115 mm 125 mm 100 mm 115 mm 125 mm

Max. wheel thickness 6 mm

Applicable cut-o wheel Max. wheel diameter 100 mm 115 mm 125 mm 100 mm 115 mm 125 mm

Max. wheel thickness 1.6 mm

Applicable wire wheel brush Max. wheel diameter -115 mm -115 mm

Max. wheel thickness -16 mm -16 mm

No load speed (n0) / Rated speed (n) 8,500 min-1

Overall length (with BL4040) 433 mm 418 mm

Net weight 3.0 - 5.4 kg 2.9 -

5.3 kg

3.0 - 5.3 kg

Rated voltage D.C. 36 V - 40 V max

Speed adjusting dial -

Wireless activation function -

•

Due to our continuing program of research and development, the specications herein are subject to change without notice.

• Specications may dier from country to country.

• The weight may dier depending on the attachment(s), including the battery cartridge. The lightest and heavi-

est combination, according to EPTA-Procedure 01/2014, are shown in the table.

Applicable battery cartridge and charger

Battery cartridge BL4020 / BL4025* / BL4040* / BL4050F* / BL4080F

* : Recommended battery

Charger DC40RA / DC40RB / DC40RC

•

Some of the battery cartridges and chargers listed above may not be available depending on your region of residence.

WARNING: Only use the battery cartridges and chargers listed above. Use of any other battery cartridges

and chargers may cause injury and/or re.

Recommended cord connected power source

Portable power pack PDC01 / PDC1200

• The cord connected power source(s) listed above may not be available depending on your region of residence.

• Before using the cord connected power source, read instruction and cautionary markings on them.

Symbols

The followings show the symbols which may be used for the equip-

ment. Be sure that you understand their meaning before use.

Read instruction manual.

Wear safety glasses.

Always operate with two hands.

Do not use the wheel guard for cut-o

operations.

Ni-MH

Li-ion

Only for EU countries

Due to the presence of hazardous com-

ponents in the equipment, waste electrical

and electronic equipment, accumulators

and batteries may have a negative impact

on the environment and human health.

Do not dispose of electrical and electronic

appliances or batteries with household waste!

In accordance with the European Directive

on waste electrical and electronic equipment

and on accumulators and batteries and

waste accumulators and batteries, as well as

their adaptation to national law, waste elec-

trical equipment, batteries and accumulators

should be stored separately and delivered

to a separate collection point for municipal

waste, operating in accordance with the

regulations on environmental protection.

This is indicated by the symbol of the

crossed-out wheeled bin placed on the

equipment.

10 ENGLISH

Intended use

The tool is intended for grinding, sanding, wire brushing

and cutting of metal and stone materials without the use

of water.

Noise

The typical A-weighted noise level determined according to EN62841-2-3:

Model Sound pressure

level (LpA) : (dB(A)) Sound power level

(LWA) : (dB(A)) Uncertainty (K) :

(dB(A))

GA042G 81 92 3

GA043G 81 92 3

GA044G 81 92 3

GA045G 81 92 3

GA046G 81 92 3

GA047G 81 92 3

NOTE: The declared noise emission value(s) has been measured in accordance with a standard test method and

may be used for comparing one tool with another.

NOTE: The declared noise emission value(s) may also be used in a preliminary assessment of exposure.

WARNING: Wear ear protection.

WARNING: The noise emission during actual use of the power tool can dier from the declared val-

ue(s) depending on the ways in which the tool is used especially what kind of workpiece is processed.

WARNING: Be sure to identify safety measures to protect the operator that are based on an estimation

of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the

times when the tool is switched o and when it is running idle in addition to the trigger time).

Vibration

The vibration total value (tri-axial vector sum) determined according to EN62841-2-3:

Work mode: surface grinding with normal side grip

Model

Vibration emission (ah, AG) : (m/s2)

Uncertainty (K) : (m/s2)

GA042G 3.3 1.5

GA043G 3.7 1.5

GA044G 4.5 1.5

GA045G 3.3 1.5

GA046G 3.7 1.5

GA047G 4.5 1.5

Work mode: surface grinding with anti vibration side grip

Model

Vibration emission (ah, AG) : (m/s2)

Uncertainty (K) : (m/s2)

GA042G 3.6 1.5

GA043G 4.0 1.5

GA044G 5.0 1.5

GA045G 3.6 1.5

GA046G 4.0 1.5

GA047G 5.0 1.5

11 ENGLISH

Work mode: disc sanding with normal side grip

Model

Vibration emission (ah, AG) : (m/s2)

Uncertainty (K) : (m/s2)

GA042G 2.5 m/s2 or less 1.9

GA043G 2.5 m/s2 or less 1.9

GA044G 2.5 m/s2 or less 1.9

GA045G 2.5 m/s2 or less 1.9

GA046G 2.5 m/s2 or less 1.9

GA047G 2.5 m/s2 or less 1.9

Work mode: disc sanding with anti vibration side grip

Model

Vibration emission (ah, AG) : (m/s2)

Uncertainty (K) : (m/s2)

GA042G 2.5 m/s2 or less 1.5

GA043G 2.5 m/s2 or less 1.5

GA044G 2.5 m/s2 or less 1.5

GA045G 2.5 m/s2 or less 1.5

GA046G 2.5 m/s2 or less 1.5

GA047G 2.5 m/s2 or less 1.5

NOTE: The declared vibration total value(s) has been measured in accordance with a standard test method and

may be used for comparing one tool with another.

NOTE: The declared vibration total value(s) may also be used in a preliminary assessment of exposure.

WARNING: The vibration emission during actual use of the power tool can dier from the declared

value(s) depending on the ways in which the tool is used especially what kind of workpiece is processed.

WARNING: Be sure to identify safety measures to protect the operator that are based on an estimation

of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the

times when the tool is switched o and when it is running idle in addition to the trigger time).

WARNING: The declared vibration emission value is used for main applications of the power tool. However if

the power tool is used for other applications, the vibration emission value may be dierent.

WARNING: Grinding thin sheets of metal or other easily vibrating structures with a large surface can

result in a total noise emission much higher (up to 15 dB) than the declared noise emission values.

Set heavy exible damping mats or such to those workpieces to prevent them from emitting sound.

Take the increased noise emission into consideration for both the risk assessment of noise exposure and

selecting adequate hearing protection.

EC Declaration of Conformity

For European countries only

The EC declaration of conformity is included as Annex A

to this instruction manual.

SAFETY WARNINGS

General power tool safety warnings

WARNING:

Read all safety warnings, instruc-

tions, illustrations and specications provided with this

power tool. Failure to follow all instructions listed below

may result in electric shock, re and/or serious injury.

Save all warnings and instruc-

tions for future reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Cordless grinder safety warnings

Safety warnings common for grinding, sanding,

wire brushing, or cutting-o operations:

1.

This power tool is intended to function as a

grinder, sander, wire brush, or cut-o tool. Read

all safety warnings, instructions, illustrations

and specications provided with this power tool.

Failure to follow all instructions listed below may

result in electric shock, re and/or serious injury.

2.

Operations such as polishing or hole cutting

are not to be performed with this power tool.

Operations for which the power tool was not designed

may create a hazard and cause personal injury.

3. Do not convert this power tool to operate in

a way which is not specically designed and

specied by the tool manufacturer. Such a con-

version may result in a loss of control and cause

serious personal injury.

4. Do not use accessories which are not spe-

cically designed and specied by the tool

manufacturer. Just because the accessory can

be attached to your power tool, it does not assure

safe operation.

12 ENGLISH

5. The rated speed of the accessory must be at

least equal to the maximum speed marked on

the power tool. Accessories running faster than

their rated speed can break and y apart.

6. The outside diameter and the thickness of your

accessory must be within the capacity rating

of your power tool. Incorrectly sized accessories

cannot be adequately guarded or controlled.

7. The dimensions of the accessory mounting

must t the dimensions of the mounting hard-

ware of the power tool. Accessories that do not

match the mounting hardware of the power tool

will run out of balance, vibrate excessively and

may cause loss of control.

8. Do not use a damaged accessory. Before each

use inspect the accessory such as abrasive

wheels for chips and cracks, backing pad for

cracks, tear or excess wear, wire brush for

loose or cracked wires. If power tool or acces-

sory is dropped, inspect for damage or install

an undamaged accessory. After inspecting and

installing an accessory, position yourself and

bystanders away from the plane of the rotating

accessory and run the power tool at maximum

no-load speed for one minute. Damaged acces-

sories will normally break apart during this test

time.

9. Wear personal protective equipment.

Depending on application, use face shield,

safety goggles or safety glasses. As appro-

priate, wear dust mask, hearing protectors,

gloves and workshop apron capable of stop-

ping small abrasive or workpiece fragments.

The eye protection must be capable of stopping

ying debris generated by various applications.

The dust mask or respirator must be capable

of ltrating particles generated by the particular

application. Prolonged exposure to high intensity

noise may cause hearing loss.

10. Keep bystanders a safe distance away from

work area. Anyone entering the work area

must wear personal protective equipment.

Fragments of workpiece or of a broken accessory

may y away and cause injury beyond immediate

area of operation.

11. Hold the power tool by insulated gripping

surfaces only, when performing an operation

where the cutting tool may contact hidden

wiring. Contact with a "live" wire will also make

exposed metal parts of the power tool "live" and

could give the operator an electric shock.

12. Never lay the power tool down until the acces-

sory has come to a complete stop. The spinning

accessory may grab the surface and pull the

power tool out of your control.

13. Do not run the power tool while carrying it at

your side. Accidental contact with the spinning

accessory could snag your clothing, pulling the

accessory into your body.

14. Regularly clean the power tool’s air vents. The

motor’s fan will draw the dust inside the housing

and excessive accumulation of powdered metal

may cause electrical hazards.

15. Do not operate the power tool near ammable

materials. Sparks could ignite these materials.

16. Do not use accessories that require liquid

coolants. Using water or other liquid coolants

may result in electrocution or shock.

Kickback and related warnings:

Kickback is a sudden reaction to a pinched or snagged

rotating wheel, backing pad, brush or any other acces-

sory. Pinching or snagging causes rapid stalling of the

rotating accessory which in turn causes the uncon-

trolled power tool to be forced in the direction opposite

of the accessory’s rotation at the point of the binding.

For example, if an abrasive wheel is snagged or

pinched by the workpiece, the edge of the wheel that is

entering into the pinch point can dig into the surface of

the material causing the wheel to climb out or kick out.

The wheel may either jump toward or away from the

operator, depending on direction of the wheel’s move-

ment at the point of pinching. Abrasive wheels may also

break under these conditions.

Kickback is the result of power tool misuse and/or

incorrect operating procedures or conditions and can be

avoided by taking proper precautions as given below.

1. Maintain a rm grip with both hands on the

power tool and position your body and arms

to allow you to resist kickback forces. Always

use auxiliary handle, if provided, for maxi-

mum control over kickback or torque reaction

during start-up. The operator can control torque

reactions or kickback forces, if proper precautions

are taken.

2. Never place your hand near the rotating acces-

sory. Accessory may kickback over your hand.

3. Do not position your body in the area where

power tool will move if kickback occurs.

Kickback will propel the tool in direction opposite

to the wheel’s movement at the point of snagging.

4. Use special care when working corners, sharp

edges, etc. Avoid bouncing and snagging the

accessory. Corners, sharp edges or bouncing

have a tendency to snag the rotating accessory

and cause loss of control or kickback.

5. Do not attach a saw chain woodcarving blade,

segmented diamond wheel with a peripheral

gap greater than 10 mm or toothed saw blade.

Such blades create frequent kickback and loss of

control.

Safety warnings specic for grinding and cut-

ting-o operations:

1. Use only wheel types that are specied

for your power tool and the specic guard

designed for the selected wheel. Wheels for

which the power tool was not designed cannot be

adequately guarded and are unsafe.

2. The grinding surface of centre depressed

wheels must be mounted below the plane of

the guard lip. An improperly mounted wheel that

projects through the plane of the guard lip cannot

be adequately protected.

3. The guard must be securely attached to the

power tool and positioned for maximum safety,

so the least amount of wheel is exposed

towards the operator. The guard helps to protect

the operator from broken wheel fragments, acci-

dental contact with wheel and sparks that could

ignite clothing.

13 ENGLISH

4.

Wheels must be used only for specied applica-

tions. For example: do not grind with the side of

cut-o wheel. Abrasive cut-o wheels are intended

for peripheral grinding, side forces applied to these

wheels may cause them to shatter.

5. Always use undamaged wheel anges that are

of correct size and shape for your selected

wheel. Proper wheel anges support the wheel

thus reducing the possibility of wheel breakage.

Flanges for cut-o wheels may be dierent from

grinding wheel anges.

6. Do not use worn down wheels from larger

power tools. A wheel intended for larger power

tool is not suitable for the higher speed of a

smaller tool and may burst.

7. When using dual purpose wheels always use

the correct guard for the application being

performed. Failure to use the correct guard may

not provide the desired level of guarding, which

could lead to serious injury.

Additional safety warnings specic for cutting-o

operations:

1. Do not “jam” the cut-o wheel or apply exces-

sive pressure. Do not attempt to make an

excessive depth of cut. Overstressing the wheel

increases the loading and susceptibility to twisting

or binding of the wheel in the cut and the possibil-

ity of kickback or wheel breakage.

2. Do not position your body in line with and

behind the rotating wheel. When the wheel, at

the point of operation, is moving away from your

body, the possible kickback may propel the spin-

ning wheel and the power tool directly at you.

3. When the wheel is binding or when interrupt-

ing a cut for any reason, switch o the power

tool and hold it motionless until the wheel

comes to a complete stop. Never attempt to

remove the cut-o wheel from the cut while

the wheel is in motion otherwise kickback may

occur. Investigate and take corrective action to

eliminate the cause of wheel binding.

4. Do not restart the cutting operation in the

workpiece. Let the wheel reach full speed and

carefully re-enter the cut. The wheel may bind,

walk up or kickback if the power tool is restarted in

the workpiece.

5. Support panels or any oversized workpiece to

minimize the risk of wheel pinching and kick-

back. Large workpieces tend to sag under their

own weight. Supports must be placed under the

workpiece near the line of cut and near the edge

of the workpiece on both sides of the wheel.

6. Use extra caution when making a “pocket cut”

into existing walls or other blind areas. The

protruding wheel may cut gas or water pipes, elec-

trical wiring or objects that can cause kickback.

7. Do not attempt to do curved cutting.

Overstressing the wheel increases the loading and

susceptibility to twisting or binding of the wheel

in the cut and the possibility of kickback or wheel

breakage, which can lead to serious injury.

8. Before using a segmented diamond wheel,

make sure that the diamond wheel has the

peripheral gap between segments of 10 mm or

less, only with a negative rake angle.

Safety warnings specic for sanding operations:

1. Use proper sized sanding disc paper. Follow

manufacturers recommendations, when

selecting sanding paper. Larger sanding paper

extending too far beyond the sanding pad pres-

ents a laceration hazard and may cause snagging,

tearing of the disc or kickback.

Safety warnings specic for wire brushing

operations:

1. Be aware that wire bristles are thrown by the

brush even during ordinary operation. Do not

overstress the wires by applying excessive

load to the brush. The wire bristles can easily

penetrate light clothing and/or skin.

2. If the use of a guard is specied for wire

brushing, do not allow any interference of the

wire wheel or brush with the guard. Wire wheel

or brush may expand in diameter due to work load

and centrifugal forces.

Additional Safety Warnings:

1. When using depressed centre grinding wheels,

be sure to use only berglass-reinforced

wheels.

2. NEVER USE Stone Cup type wheels with this

grinder. This grinder is not designed for these

types of wheels and the use of such a product

may result in serious personal injury.

3. Be careful not to damage the X-LOCK holder.

Damage to the parts could result in wheel

breakage.

4. Make sure the wheel is not contacting the

workpiece before the switch is turned on.

5. Before using the tool on an actual workpiece,

let it run for a while. Watch for vibration or

wobbling that could indicate poor installation

or a poorly balanced wheel.

6. Use the specied surface of the wheel to per-

form the grinding.

7. Do not leave the tool running. Operate the tool

only when hand-held.

8. Do not touch the workpiece immediately after

operation; it may be extremely hot and could

burn your skin.

9. Do not touch accessories immediately after

operation; it may be extremely hot and could

burn your skin.

10. Observe the instructions of the manufacturer

for correct mounting and use of wheels.

Handle and store wheels with care.

11. Do not use separate reducing bushings or

adaptors to adapt large hole abrasive wheels.

12.

Check that the workpiece is properly supported.

13. Pay attention that the wheel continues to

rotate after the tool is switched o.

14. If working place is extremely hot and humid,

or badly polluted by conductive dust, use a

short-circuit breaker (30 mA) to assure opera-

tor safety.

15. Do not use the tool on any materials contain-

ing asbestos.

16. When use cut-o wheel, always work with

the dust collecting wheel guard if required by

domestic regulation.

14 ENGLISH

17. Cutting discs must not be subjected to any

lateral pressure.

18. Do not use cloth work gloves during operation.

Fibers from cloth gloves may enter the tool, which

causes tool breakage.

19.

Before operation, make sure that there is no

buried object such as electric pipe, water pipe or

gas pipe in the workpiece. Otherwise, it may cause

an electric shock, electrical leakage or gas leak.

SAVE THESE INSTRUCTIONS.

WARNING: DO NOT let comfort or familiarity

with product (gained from repeated use) replace

strict adherence to safety rules for the subject

product. MISUSE or failure to follow the safety

rules stated in this instruction manual may cause

serious personal injury.

Important safety instructions for

battery cartridge

1.

Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery char-

ger, (2) battery, and (3) product using battery.

2. Do not disassemble or tamper with the battery

cartridge. It may result in a re, excessive heat,

or explosion.

3. If operating time has become excessively

shorter, stop operating immediately. It may

result in a risk of overheating, possible burns

and even an explosion.

4. If electrolyte gets into your eyes, rinse them

out with clear water and seek medical atten-

tion right away. It may result in loss of your

eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any con-

ductive material.

(2) Avoid storing battery cartridge in a con-

tainer with other metal objects such as

nails, coins, etc.

(3) Do not expose battery cartridge to water

or rain.

A battery short can cause a large current

ow, overheating, possible burns and even a

breakdown.

6. Do not store and use the tool and battery car-

tridge in locations where the temperature may

reach or exceed 50 °C (122 °F).

7. Do not incinerate the battery cartridge even if

it is severely damaged or is completely worn

out. The battery cartridge can explode in a re.

8. Do not nail, cut, crush, throw, drop the battery

cartridge, or hit against a hard object to the

battery cartridge. Such conduct may result in a

re, excessive heat, or explosion.

9. Do not use a damaged battery.

10. The contained lithium-ion batteries are subject

to the Dangerous Goods Legislation require-

ments.

For commercial transports e.g. by third parties,

forwarding agents, special requirement on pack-

aging and labeling must be observed.

For preparation of the item being shipped, consult-

ing an expert for hazardous material is required.

Please also observe possibly more detailed

national regulations.

Tape or mask o open contacts and pack up the

battery in such a manner that it cannot move

around in the packaging.

11. When disposing the battery cartridge, remove

it from the tool and dispose of it in a safe

place. Follow your local regulations relating to

disposal of battery.

12. Use the batteries only with the products

specied by Makita. Installing the batteries to

non-compliant products may result in a re, exces-

sive heat, explosion, or leak of electrolyte.

13. If the tool is not used for a long period of time,

the battery must be removed from the tool.

14. During and after use, the battery cartridge may

take on heat which can cause burns or low

temperature burns. Pay attention to the han-

dling of hot battery cartridges.

15. Do not touch the terminal of the tool imme-

diately after use as it may get hot enough to

cause burns.

16. Do not allow chips, dust, or soil stuck into the

terminals, holes, and grooves of the battery

cartridge. It may cause heating, catching re,

burst and malfunction of the tool or battery car-

tridge, resulting in burns or personal injury.

17. Unless the tool supports the use near

high-voltage electrical power lines, do not use

the battery cartridge near a high-voltage elec-

trical power lines. It may result in a malfunction

or breakdown of the tool or battery cartridge.

18. Keep the battery away from children.

SAVE THESE INSTRUCTIONS.

CAUTION: Only use genuine Makita batteries.

Use of non-genuine Makita batteries, or batteries that

have been altered, may result in the battery bursting

causing res, personal injury and damage. It will

also void the Makita warranty for the Makita tool and

charger.

Tips for maintaining maximum

battery life

1. Charge the battery cartridge before completely

discharged. Always stop tool operation and

charge the battery cartridge when you notice

less tool power.

2. Never recharge a fully charged battery car-

tridge. Overcharging shortens the battery

service life.

3. Charge the battery cartridge with room tem-

perature at 10 °C - 40 °C (50 °F - 104 °F). Let

a hot battery cartridge cool down before

charging it.

4. When not using the battery cartridge, remove

it from the tool or the charger.

5. Charge the battery cartridge if you do not use

it for a long period (more than six months).

15 ENGLISH

Important safety instructions for

wireless unit

1. Do not disassemble or tamper with the wire-

less unit.

2. Keep the wireless unit away from young chil-

dren. If accidentally swallowed, seek medical

attention immediately.

3. Use the wireless unit only with Makita tools.

4. Do not expose the wireless unit to rain or wet

conditions.

5. Do not use the wireless unit in places where

the temperature exceeds 50 °C (122 °F).

6. Do not operate the wireless unit in places

where medical instruments, such as heart

pace makers are nearby.

7. Do not operate the wireless unit in places

where automated devices are nearby. If oper-

ated, automated devices may develop malfunction

or error.

8. Do not operate the wireless unit in places

under high temperature or places where

static electricity or electrical noise could be

generated.

9. The wireless unit can produce electromagnetic

elds (EMF) but they are not harmful to the

user.

10. The wireless unit is an accurate instrument. Be

careful not to drop or strike the wireless unit.

11. Avoid touching the terminal of the wireless

unit with bare hands or metallic materials.

12. Always remove the battery on the product

when installing the wireless unit into it.

13. When opening the lid of the slot, avoid the

place where dust and water may come into the

slot. Always keep the inlet of the slot clean.

14. Always insert the wireless unit in the correct

direction.

15. Do not press the wireless activation button

on the wireless unit too hard and/or press the

button with an object with a sharp edge.

16. Always close the lid of the slot when

operating.

17. Do not remove the wireless unit from the slot

while the power is being supplied to the tool.

Doing so may cause a malfunction of the wireless

unit.

18. Do not remove the sticker on the wireless unit.

19. Do not put any sticker on the wireless unit.

20. Do not leave the wireless unit in a place where

static electricity or electrical noise could be

generated.

21. Do not leave the wireless unit in a place sub-

ject to high heat, such as a car sitting in the

sun.

22. Do not leave the wireless unit in a dusty or

powdery place or in a place corrosive gas

could be generated.

23. Sudden change of the temperature may bedew

the wireless unit. Do not use the wireless unit

until the dew is completely dried.

24. When cleaning the wireless unit, gently wipe

with a dry soft cloth. Do not use benzine, thin-

ner, conductive grease or the like.

25. When storing the wireless unit, keep it in the

supplied case or a static-free container.

26. Do not insert any devices other than Makita

wireless unit into the slot on the tool.

27. Do not use the tool with the lid of the slot dam-

aged. Water, dust, and dirt come into the slot may

cause malfunction.

28. Do not pull and/or twist the lid of the slot more

than necessary. Restore the lid if it comes o

from the tool.

29. Replace the lid of the slot if it is lost or

damaged.

SAVE THESE INSTRUCTIONS.

FUNCTIONAL

DESCRIPTION

CAUTION: Always be sure that the tool is

switched o and the battery cartridge is removed

before adjusting or checking function on the tool.

Installing or removing battery

cartridge

CAUTION: Always switch o the tool before

installing or removing of the battery cartridge.

CAUTION: Hold the tool and the battery car-

tridge rmly when installing or removing battery

cartridge. Failure to hold the tool and the battery

cartridge rmly may cause them to slip o your hands

and result in damage to the tool and battery cartridge

and a personal injury.

To remove the battery cartridge, slide it from the tool

while sliding the button on the front of the cartridge.

► Fig.1: 1. Red indicator 2. Button 3. Battery cartridge

To install the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Insert it all the way until it locks in place

with a little click. If you can see the red indicator as

shown in the gure, it is not locked completely.

CAUTION: Always install the battery cartridge

fully until the red indicator cannot be seen. If not,

it may accidentally fall out of the tool, causing injury to

you or someone around you.

CAUTION: Do not install the battery cartridge

forcibly. If the cartridge does not slide in easily, it is

not being inserted correctly.

16 ENGLISH

Indicating the remaining battery

capacity

Press the check button on the battery cartridge to indi-

cate the remaining battery capacity. The indicator lamps

light up for a few seconds.

► Fig.2: 1. Indicator lamps 2. Check button

Indicator lamps Remaining

capacity

Lighted O Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the

battery.

The battery

may have

malfunctioned.

NOTE: Depending on the conditions of use and the

ambient temperature, the indication may dier slightly

from the actual capacity.

NOTE: The rst (far left) indicator lamp will blink when

the battery protection system works.

Tool / battery protection system

The tool is equipped with a tool/battery protection sys-

tem. This system automatically cuts o power to the

motor to extend tool and battery life. The tool will auto-

matically stop during operation if the tool or battery is

placed under one of the following conditions:

Overload protection

When the tool/battery is operated in a manner that

causes it to draw an abnormally high current, the tool

automatically stops without any indication. In this sit-

uation, turn the tool o and stop the application that

caused the tool to become overloaded. Then turn the

tool on to restart.

Overheat protection

When the tool/battery is overheated, the tool stops

automatically. Let the tool cool down before turning the

tool on again.

Overdischarge protection

When the battery capacity is not enough, the tool stops

automatically. In this case, remove the battery from the

tool and charge the battery.

Releasing protection lock

When the protection system works repeatedly, the tool is locked.

In this situation, the tool does not start even if turning

the tool o and on. To release the protection lock,

remove the battery, set it to the battery charger and wait

until the charging nishes.

Protections against other causes

Protection system is also designed for other causes

that could damage the tool and allows the tool to stop

automatically. Take all the following steps to clear the

causes, when the tool has been brought to a temporary

halt or stop in operation.

1.

Turn the tool o, and then turn it on again to restart.

2. Charge the battery(ies) or replace it/them with

recharged battery(ies).

3. Let the tool and battery(ies) cool down.

If no improvement can be found by restoring protection

system, then contact your local Makita Service Center.

Switch action

CAUTION: Before installing the battery car-

tridge into the tool, always check to see that the

switch lever actuates properly and returns to the

"OFF" position when released.

CAUTION: For your safety, this tool is

equipped with lock-o lever which prevents the

tool from unintended starting. NEVER use the tool

if it runs when you simply pull the switch lever

without pulling the lock-o lever. Return the tool

to our authorized service center for proper repairs

BEFORE further usage.

CAUTION: Do not pull the switch lever hard

without pulling the lock-o lever. This can cause

switch breakage.

CAUTION: NEVER tape down or defeat pur-

pose and function of lock-o lever.

To prevent the switch lever from being accidentally

pulled, a lock-o lever is provided.

To start the tool, pull the lock-o lever toward the opera-

tor and then pull the switch lever.

To stop the tool, release the switch lever.

► Fig.3: 1. Lock-o lever 2. Switch lever

Speed adjusting dial

Only for model GA042G / GA043G / GA044G

The rotation speed of the tool can be changed by turn-

ing the speed adjusting dial. The table below shows

the number on the dial and the corresponding rotation

speed.

► Fig.4: 1. Speed adjusting dial

Number Speed

13,000 min-1

24,500 min-1

36,000 min-1

47,500 min-1

58,500 min-1

17 ENGLISH

NOTICE: If the tool is operated continuously at

low speed for a long time, the motor will get over-

loaded, resulting in tool malfunction.

NOTICE: The speed adjusting dial can be turned

only as far as 5 and back to 1. Do not force it past

5 or 1, or the speed adjusting function may no

longer work.

Electric brake

Electric brake is activated after the tool is switched o.

The brake does not work when the power supply is shut

down, such as the battery is removed accidentally, with

the switch still on.

If the tool consistently fails to quickly stop after turning

o the switch, have the tool serviced at a Makita Service

Center.

Electronic function

Accidental re-start preventive

function

When installing the battery cartridge while the switch is

ON, the tool does not start.

To start the tool, turn o the switch, and turn it on again.

Active Feedback sensing Technology

The tool electronically detects situations where the

wheel or accessory may be at risk to be bound. In the

situation, the tool is automatically shut o to prevent

further rotation of the spindle (it does not prevent

kickback).

To restart the tool, switch o the tool rst, remove the

cause of sudden drop in the rotation speed, and then

turn the tool on.

Soft start feature

Soft start feature reduces starting reaction.

ASSEMBLY

CAUTION: Always be sure that the tool is

switched o and the battery cartridge is removed

before adjusting or checking function on the tool.

Installing side grip (handle)

CAUTION: Always be sure that the side grip is

installed securely before operation.

Screw the side grip securely on the position of the tool

as shown in the gure.

► Fig.5

Installing or removing wheel guard

WARNING: When using a depressed center

wheel, ap disc or wire wheel brush, the wheel

guard must be tted on the tool so that the

closed side of the guard always points toward the

operator.

WARNING: Make sure that the wheel guard is

securely locked by the lock lever with one of the

holes on the wheel guard.

WARNING: When using an abrasive cut-o

/ diamond wheel, be sure to use only the special

wheel guard designed for use with cut-o wheels.

For depressed center wheel, ap

disc, wire wheel brush / abrasive cut-

o wheel, diamond wheel

1. While pushing the lock lever, mount the wheel

guard with the protrusions on the wheel guard aligned

with the notches on the bearing box.

► Fig.6: 1. Lock lever 2. Notch 3. Protrusion

2.

While pushing the lock lever toward A, hold down

the portions B of the wheel guard as shown in the gure.

► Fig.7: 1. Wheel guard 2. Hole

NOTE: Push down the wheel guard straight.

Otherwise, you cannot secure the wheel guard.

3. While pushing the lock lever toward A, rotate the

wheel guard toward C, and then, change the angle of

the wheel guard according to the work so that the oper-

ator can be protected. Align the lock lever with one of

the holes in the wheel guard, and then release the lock

lever to lock the wheel guard.

► Fig.8: 1. Wheel guard 2. Hole

To remove wheel guard, follow the installation proce-

dure in reverse.

Installing depressed center wheel or

ap disc

Optional accessory

WARNING: When using a depressed center

wheel or a ap disc, the wheel guard must be

tted on the tool so that the closed side of the

guard always points toward the operator.

► Fig.9: 1. Depressed center wheel 2. Wheel guard

Installing abrasive cut-o / diamond wheel

Optional accessory

WARNING: When using an abrasive cut-o

/ diamond wheel, be sure to use only the special

wheel guard designed for use with cut-o wheels.

WARNING: NEVER use cut-o wheel for side

grinding.

► Fig.10: 1. Abrasive cut-o wheel / diamond wheel

2. Wheel guard for abrasive cut-o wheel /

diamond wheel

18 ENGLISH

Clip-on cutting wheel guard

attachment

Optional accessory

NOTE: For cutting-o operations, a clip-on cutting

wheel guard attachment can be used with the wheel

guard (for grinding wheel).

Not available in some countries.

► Fig.11

Installing wire cup brush

Optional accessory

CAUTION: Do not use wire cup brush that is

damaged, or which is out of balance. Use of dam-

aged brush could increase potential for injury from

contact with broken brush wires.

► Fig.12: 1. Wire cup brush

Installing wire wheel brush

Optional accessory

CAUTION: Do not use wire wheel brush that

is damaged, or which is out of balance. Use of

damaged wire wheel brush could increase potential

for injury from contact with broken wires.

CAUTION: ALWAYS use guard with wire

wheel brushes, assuring diameter of wheel ts

inside guard. Wheel can shatter during use and

guard helps to reduce chances of personal injury.

► Fig.13: 1. Wire wheel brush 2. Wheel guard

Installing or removing X-LOCK wheel

WARNING: Never actuate the release lever of

the X-LOCK holder during operation. Make sure

that the X-LOCK wheel has stopped completely

when removing it. Otherwise, the X-LOCK wheel

comes o from the tool and may cause serious injury.

CAUTION: Use only original X-LOCK wheels

with the X-LOCK logo. This tool is dedicated to

X-LOCK.

The maximum clamping gauge of 1.6 mm can only be

guaranteed with original X-LOCK wheels.

Use of any other wheels may lead to insecure clamp-

ing, and cause the clamp tool to come loose.

CAUTION: Do not touch the X-LOCK wheel

immediately after operation. It may be extremely

hot and could burn your skin.

CAUTION: Make sure that the X-LOCK wheel

and holder of the tool are not deformed and are

free from dust or foreign matters.

CAUTION: Do not put your nger near the

holder while installing or removing the X-LOCK

wheel. It may pinch your nger.

CAUTION: Do not put your nger near the

release lever while installing the X-LOCK wheel. It

may pinch your nger.

NOTE: No additional parts such as inner anges

or lock nuts are required to install or remove the

X-LOCK wheels.

1. To install the X-LOCK wheel, make sure that both

catches are in the unlocked position.

If not, push the release lever from A side to lift B

side, then pull the release lever from B side as

illustrated. The catches are set in the unlocked

position.

► Fig.14: 1. Catch 2. Release lever

2. Place a central position of the X-LOCK wheel on

the holder.

Make sure the X-LOCK wheel is parallel to the

ange surface and with the correct side facing up.

3. Push the X-LOCK wheel into the holder. The

catches snap into the lock position with a click and

x the X-LOCK wheel.

► Fig.15: 1. X-LOCK wheel 2. Holder 3. Flange sur-

face 4. Catch

4. Make sure the X-LOCK wheel is xed correctly.

The surface of the X-LOCK wheel is no higher

than the surface of the holder as shown in the

gure.

If not, the holder must be cleaned or the X-LOCK

wheel must not be used.

► Fig.16: 1. Surface of the holder 2. Surface of the

X-LOCK wheel

To remove the X-LOCK wheel, push the release lever

from A side to lift B side, then pull the release lever from

B side as illustrated.

The X-LOCK wheel is released and can be removed.

► Fig.17: 1. Release lever

Installing dust collecting wheel

guard for cutting-o

Optional accessory

With optional accessories, you can use this tool for

cutting stone materials.

► Fig.18

NOTE: For information how to install the dust col-

lecting wheel guard, refer to the manual of the dust

collecting wheel guard.

Connecting a vacuum cleaner

Optional accessory

WARNING: Never vacuum metal particles

created by grinding/cutting/sanding operation.

Metal particles created by such operation are so hot

that they ignite dust and the lter inside the vacuum

cleaner.

To avoid dusty environment caused by masonry cut-

ting, use a dust collecting wheel guard and a vacuum

cleaner.

Refer to the instruction manual attached to the dust

collecting wheel guard for assembling and using it.

► Fig.19: 1. Dust collecting wheel guard 2. Hose of

the vacuum cleaner

19 ENGLISH

OPERATION

WARNING: It should never be necessary to

force the tool. The weight of the tool applies ade-

quate pressure. Forcing and excessive pressure

could cause dangerous wheel breakage.

WARNING: ALWAYS replace wheel if tool is

dropped while grinding.

WARNING: NEVER hit the workpiece with the

wheel.

WARNING: Avoid bouncing and snagging

the wheel, especially when working corners,

sharp edges etc. This can cause loss of control and

kickback.

WARNING: NEVER use tool with wood cutting

blades and other saw blades. Such blades when

used on a grinder frequently kick and cause loss of

control leading to personal injury.

WARNING: Never actuate the release lever of

the X-LOCK holder during operation. The X-LOCK

wheel comes o from the tool and may cause serious

injury.

WARNING: Make sure that the X-LOCK wheel

is xed rmly.

CAUTION: Never switch on the tool when it

is in contact with the workpiece, it may cause an

injury to operator.

CAUTION: Always wear safety goggles or a

face shield during operation.

CAUTION: After operation, always switch o

the tool and wait until the wheel has come to a

complete stop before putting the tool down.

CAUTION: ALWAYS hold the tool rmly with

one hand on housing and the other on the side

grip (handle).

Grinding and sanding operation

► Fig.20

Turn the tool on and then apply the wheel or disc to the

workpiece.

In general, keep the edge of the wheel or disc at an

angle of about 15° to the workpiece surface.

During the break-in period with a new wheel, do not

work the grinder in forward direction or it may cut into

the workpiece. Once the edge of the wheel has been

rounded o by use, the wheel may be worked in both

forward and backward direction.

Operation with abrasive cut-o /

diamond wheel

Optional accessory

WARNING: Do not "jam" the wheel or apply

excessive pressure. Do not attempt to make an

excessive depth of cut. Overstressing the wheel

increases the loading and susceptibility to twisting

or binding of the wheel in the cut and the possibility

of kickback, wheel breakage and overheating of the

motor may occur.

WARNING: Do not start the cutting operation

in the workpiece. Let the wheel reach full speed

and carefully enter into the cut moving the tool

forward over the workpiece surface. The wheel

may bind, walk up or kickback if the power tool is

started in the workpiece.

WARNING: During cutting operations, never

change the angle of the wheel. Placing side pres-

sure on the cut-o wheel (as in grinding) will cause

the wheel to crack and break, causing serious per-

sonal injury.

WARNING: A diamond wheel shall be oper-

ated perpendicular to the material being cut.

Usage example: operation with abrasive cut-o

wheel

► Fig.21

Usage example: operation with diamond wheel

► Fig.22

Operation with wire cup brush

Optional accessory

CAUTION: Check operation of brush by run-

ning tool with no load, insuring that no one is in

front of or in line with brush.

NOTICE: Avoid applying too much pressure

which causes over bending of wires when using

the wire cup brush. It may lead to premature

breakage.

Usage example: operation with wire cup brush

► Fig.23

Operation with wire wheel brush

Optional accessory

CAUTION: Check operation of wire wheel

brush by running tool with no load, insuring that

no one is in front of or in line with the wire wheel

brush.

NOTICE: Avoid applying too much pressure

which causes over bending of wires when

using wire wheel brush. It may lead to premature

breakage.

Usage example: operation with wire wheel brush

► Fig.24

20 ENGLISH

WIRELESS ACTIVATION

FUNCTION

Only for model GA042G / GA043G / GA044G

What you can do with the wireless

activation function

The wireless activation function enables clean and com-

fortable operation. By connecting a supported vacuum

cleaner to the tool, you can run the vacuum cleaner

automatically along with the switch operation of the tool.

► Fig.25

To use the wireless activation function, prepare follow-

ing items:

• A wireless unit (optional accessory)

• A vacuum cleaner which supports the wireless

activation function

The overview of the wireless activation function

setting is as follows. Refer to each section for detail

procedures.

1. Installing the wireless unit

2. Tool registration for the vacuum cleaner

3. Starting the wireless activation function

Installing the wireless unit

Optional accessory

CAUTION: Place the tool on a at and stable

surface when installing the wireless unit.

NOTICE: Clean the dust and dirt on the tool

before installing the wireless unit. Dust or dirt

may cause malfunction if it comes into the slot of the

wireless unit.

NOTICE: To prevent the malfunction caused by

static, touch a static discharging material, such

as a metal part of the tool, before picking up the

wireless unit.

NOTICE: When installing the wireless unit,

always be sure that the wireless unit is inserted

in the correct direction and the lid is completely

closed.

1. Open the lid on the tool as shown in the gure.

► Fig.26: 1. Lid

2. Insert the wireless unit to the slot and then close

the lid.

When inserting the wireless unit, align the projections

with the recessed portions on the slot.

► Fig.27: 1. Wireless unit 2. Projection 3. Lid

4. Recessed portion

When removing the wireless unit, open the lid slowly.

The hooks on the back of the lid will lift the wireless unit

as you pull up the lid.

► Fig.28: 1. Wireless unit 2. Hook 3. Lid

After removing the wireless unit, keep it in the supplied

case or a static-free container.

NOTICE: Always use the hooks on the back of

the lid when removing the wireless unit. If the

hooks do not catch the wireless unit, close the lid

completely and open it slowly again.

Tool registration for the vacuum

cleaner

NOTE: A Makita vacuum cleaner supporting the

wireless activation function is required for the tool

registration.

NOTE: Finish installing the wireless unit to the tool

before starting the tool registration.

NOTE: During the tool registration, do not pull the

switch trigger or turn on the power switch on the

vacuum cleaner.

NOTE: Refer to the instruction manual of the vacuum

cleaner, too.

If you wish to activate the vacuum cleaner along with

the switch operation of the tool, nish the tool registra-

tion beforehand.

1. Install the batteries to the vacuum cleaner and the

tool.

2. Set the stand-by switch on the vacuum cleaner to

"AUTO".

► Fig.29: 1. Stand-by switch

3. Press the wireless activation button on the vac-

uum cleaner for 3 seconds until the wireless activation

lamp blinks in green. And then press the wireless acti-

vation button on the tool in the same way.

► Fig.30: 1. Wireless activation button 2. Wireless

activation lamp

If the vacuum cleaner and the tool are linked success-

fully, the wireless activation lamps will light up in green

for 2 seconds and start blinking in blue.

NOTE: The wireless activation lamps nish blinking

in green after 20 seconds elapsed. Press the wireless

activation button on the tool while the wireless acti-

vation lamp on the cleaner is blinking. If the wireless

activation lamp does not blink in green, push the wire-

less activation button briey and hold it down again.

NOTE: When performing two or more tool registra-

tions for one vacuum cleaner, nish the tool registra-

tion one by one.

Starting the wireless activation

function

NOTE: Finish the tool registration for the vacuum

cleaner prior to the wireless activation.

NOTE: Refer to the instruction manual of the vacuum

cleaner, too.

After registering a tool to the vacuum cleaner, the

vacuum cleaner will automatically runs along with the

switch operation of the tool.

1. Install the wireless unit to the tool.

2. Connect the hose of the vacuum cleaner with the

tool.

► Fig.31

Stránka sa načítava ...

Makita GA042G Používateľská príručka

Makita GA042G Používateľská príručka

V iných jazykoch