HOTPOINT/ARISTON FMSDN 623B CZ Užívateľská príručka

Kategória
Práčky
Typ
Užívateľská príručka
GB
1
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Care and maintenance, 4
Cutting off the water or electricity supply
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Precautions and tips, 5
General safety
Disposal
Opening the porthole door manually
Description of the washing machine, 6-7
Control panel
Display
Running a wash cycle, 8
Wash cycles and functions, 9
Table of wash cycles
Wash functions
Detergents and laundry, 10
Detergent dispenser drawer
Preparing the laundry
Special wash cycles
Load balancing system
Troubleshooting, 11
Service, 12
FMSDN 623
Instructions for use
WASHING MACHINE
English,1
GB
Česky,13
CZ
SK
Slovensky,25
Română,37
RO
2
GB
Installation
! This instruction manual should be kept in a
safe place for future reference. If the washing
machine is sold, transferred or moved, make
sure that the instruction manual remains with
the machine so that the new owner is able to
familiarise himself/herself with its operation
and features.
! Read these instructions carefully: they con-
tain vital information relating to the safe instal-
lation and operation of the appliance.
Unpacking and levelling
Unpacking
1. Remove the washing machine from its
packaging.
2. Make sure that the washing machine has
not been damaged during the transportation
process. If it has been damaged, contact the
retailer and do not proceed any further with
the installation process.
3. Remove the 4 pro-
tective screws (used
during transportation)
and the rubber wa-
sher with the cor-
responding spacer,
located on the rear
part of the appliance
(see figure).
4. Close off the holes using the plastic plugs
provided.
5. Keep all the parts in a safe place: you will
need them again if the washing machine ne-
eds to be moved to another location.
! Packaging materials should not be used as
toys for children.
Levelling
1. Install the washing
machine on a flat
sturdy floor, without
resting it up against
walls, furniture cabi-
nets or anything else.
2. If the floor is not
perfectly level, com-
pensate for any une-
venness by tightening or loosening the adju-
stable front feet (see figure); the angle of incli-
nation, measured in relation to the worktop,
must not exceed 2°.
Levelling the machine correctly will provide
it with stability, help to avoid vibrations and
excessive noise and prevent it from shifting
while it is operating. If it is placed on carpet or
a rug, adjust the feet in such a way as to allow
a sufficient ventilation space underneath the
washing machine.
Connecting the electricity and
water supplies
Connecting the water inlet hose
1. Connect the inlet
hose by screwing it to
a cold water tap using
a 3/4 gas threaded
connection (see figu-
re).
Before performing the
connection, allow the
water to run freely un-
til it is perfectly clear.
2. Connect the inlet
hose to the washing
machine by screwing
it onto the correspon-
ding water inlet of the
appliance, which is
situated on the top
right-hand side of the
rear part of the ap-
pliance (see figure).
3. Make sure that the hose is not folded over
or bent.
! The water pressure at the tap must fall within
the range of values indicated in the Technical
data table (see next page).
! If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.
! Never use second-hand hoses.
! Use the ones supplied with the machine.
GB
3
Connecting the drain hose
Connect the drain
hose, without bending
it, to a drain duct or
a wall drain situated
between 65 and 100
cm from the floor;
alternatively, placed
it over the edge of a
basin, sink or tub, fa-
stening the duct sup-
plied to the tap (see
figure). The free end
of the hose should
not be underwater.
! We advise against the use of hose extensions;
if it is absolutely necessary, the extension must
have the same diameter as the original hose
and must not exceed 150 cm in length.
Electrical connections
Before plugging the appliance into the electri-
city socket, make sure that:
• thesocketisearthedandcomplieswithall
applicable laws;
• thesocketisabletowithstandthemaxi-
mum power load of the appliance as indicated
in the Technical data table (see opposite);
• thepowersupplyvoltagefallswithintheva-
lues indicated in the Technical data table (see
opposite);
• thesocketiscompatiblewiththeplugofthe
washing machine. If this is not the case, repla-
ce the socket or the plug.
! The washing machine must not be installed
outdoors, even in covered areas. It is extreme-
ly dangerous to leave the appliance exposed
to rain, storms and other weather conditions.
! When the washing machine has been instal-
led, the electricity socket must remain within
easy reach.
65 - 100 cm
! Do not use extension cords or multiple so-
ckets.
! The cable should not be bent or compres-
sed.
! The power supply cable must only be repla-
ced by authorised technicians.
Warning! The company shall not be held re-
sponsible in the event that these standards are
not observed.
The first wash cycle
Once the appliance has been installed, and
before you use it for the first time, run a wash
cycle with detergent and no laundry, using
wash cycle number “Auto Clean” (see “Clea-
ning the washing machine”).
Technical data
Model
FMSDN 623
Dimensions
width 59.5 cm
height 85 cm
depth 42,5 cm
Capacity
from 1 to 6 kg
Electrical
connections
please refer to the technical
data plate fixed to the ma-
chine
Water con-
nections
maximum pressure
1 MPa (10 bar)
minimum pressure
0.05 MPa (0.5 bar)
drum capacity 40 litres
Spin speed
up to 1200 rotations per
minute
Test wash
cycles in
accordan-
ce with
directives
1061/2010
1015/2010
programme 2 (60°) (1st
press of the button);
Cotton Standard 60°.
programme 2 (40°) (2nd
press of the button);
Cotton Standard 40°.
This appliance conforms to
the following EC Directives:
- 2004/108/EC (Electroma-
gnetic Compatibility)
- 2006/95/EC (Low Voltage)
- 2012/19/EU
4
GB
Care and maintenance
Cutting off the water and electri-
city supplies
•Turnoffthewatertapaftereverywashcycle.
This will limit wear on the hydraulic system in-
side the washing machine and help to prevent
leaks.
•Unplugthewashingmachinewhencleaning
it and during all maintenance work.
Cleaning the washing machine
•Theouterpartsandrubbercomponents
of the appliance can be cleaned using a soft
cloth soaked in lukewarm soapy water. Do not
use solvents or abrasives.
•Thewashingmachinehasa“AutoClean”
programme for its internal parts that must be
run with no load in the drum.
To help the wash cycle
you may want to use
either the detergent
(i.e. a quantity 10% the
quantity specified for
lightly-soiled garments)
or special additives to
clean the washing ma-
chine. We recommend
running a cleaning
programme every 40 wash cycles.
To start the programme press buttons A and
B simultaneously for 5 seconds (see figure).
The programme will start automatically and will
run for about 70 minutes. To stop the cycle
press the START/PAUSE button.
Cleaning the detergent dispenser
drawer
Remove the dispenser
by raising it and pul-
ling it out (see figure).
Wash it under running
water; this operation
should be repeated
frequently.
1
2
BA
Caring for the door and drum of
your appliance
•Alwaysleavetheportholedoorajarinorder
to prevent unpleasant odours from forming.
Cleaning the pump
The washing machine is fitted with a self-clea-
ning pump which does not require any mainte-
nance. Sometimes, small items (such as coins
or buttons) may fall into the pre-chamber which
protects the pump, situated in its bottom part.
! Make sure the wash cycle has finished and
unplug the appliance.
To access the pre-chamber:
1. using a screwdri-
ver, remove the cover
panel on the lower
front part of the wa-
shing machine (see
figure);
2. unscrew the lid
by rotating it anti-
clockwise (see figu-
re): a little water may
trickle out. This is
perfectly normal;
3. clean the inside thoroughly;
4. screw the lid back on;
5. reposition the panel, making sure the hooks
are securely in place before you push it onto
the appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If
there are any cracks, it should be replaced
immediately: during the wash cycles, water
pressure is very strong and a cracked hose
could easily split open.
! Never use second-hand hoses.
GB
5
Precautions and tips
! This washing machine was designed and constructed in
accordance with international safety regulations. The fol-
lowing information is provided for safety reasons and must
therefore be read carefully.
General safety
• Thisappliancewasdesignedfordomesticuseonly.
This appliance can be used by children aged
from 8 years and above and persons with re-
duced physical, sensory or mental capabilities
or lack of experience and knowledge if they
have been given supervision or instruction
concerning use of the appliance in a safe way
and understand the hazards involved. Chil-
dren shall not play with the appliance. Clea-
ning and user maintenance shall not be made
by children without supervision.
• Donottouchthemachinewhenbarefootorwithwetor
damp hands or feet.
• Donotpullonthepowersupplycablewhenunplugging
the appliance from the electricity socket. Hold the plug
and pull.
• Donotopenthedetergentdispenserdrawerwhilethe
machine is in operation.
• Donottouchthedrainedwaterasitmayreachextreme-
ly high temperatures.
Neverforcetheportholedoor.Thiscoulddamagethesafety
lock mechanism designed to prevent accidental opening.
• Iftheappliancebreaksdown,donotunderanycircum-
stances access the internal mechanisms in an attempt
to repair it yourself.
• Alwayskeepchildrenwellawayfromtheappliancewhile
it is operating.
• Thedoorcanbecomequitehotduringthewashcycle.
• Iftheappliancehastobemoved,workinagroupoftwo
or three people and handle it with the utmost care. Never
try to do this alone, because the appliance is very heavy.
• Beforeloadinglaundryintothewashingmachine,make
sure the drum is empty.
Disposal
•Disposingofthepackagingmaterials:observelocalregu-
lations so that the packaging may be re-used.
•TheEuropeanDirective2012/19/EUonWasteElectrical
and Electronic Equipment, requires that old household
electrical appliances must not be disposed of in the normal
unsorted municipal waste stream. Old appliances must be
collected separately in order to optimise the recovery and
recycling of the materials they contain and reduce the im-
pact on human health and the environment. The crossed
out “wheeled bin” symbol on the product reminds you of
your obligation, that when you dispose of the appliance it
must be separately collected. Consumers should contact
their local authority or retailer for information concerning the
correct disposal of their old appliance.
Opening the porthole door manually
In the event that it is not possible to open the porthole
door due to a powercut, and if you wish to remove the
laundry, proceed as follows:
1. remove the plug from the
electrical socket.
2. make sure the water level
inside the machine is lower
than the door opening; if it
is not, remove excess water
using the drain hose, collec-
ting it in a bucket as indicated
in the figure.
3. using a screwdriver, remo-
ve the cover panel on the lo-
wer front part of the washing
machine (see figure).
4. pull outwards using the tab as indicated in the figure,
until the plastic tie-rod is freed from its stop position; pull
downwards and open the door at the same time.
5. reposition the panel, making sure the hooks are securely
in place before you push it onto the appliance.
20
6
GB
Detergent dispenser drawer: used to dispense deter-
gents and washing additives (see “Detergents and laundry”).
ON/OFF button : press this briefly to switch the ma-
chine on or off. The START/PAUSE indicator light, which
flashes slowly in a green colour shows that the machine is
switched on. To switch off the washing machine during the
wash cycle, press and hold the button for approximately 3
seconds; if the button is pressed briefly or accidentally the
machine will not switch off. If the machine is switched off
during a wash cycle, this wash cycle will be cancelled.
WASH CYCLE SELECTOR buttons: used to set the
desired wash cycle (see “Table of wash cycles”).
MY CYCLE button: press and hold the button to store a
cycle with your own set of preferences in the memory of
the machine. To recall a previously stored cycle, press the
MY CYCLE button.
FUNCTION buttons: press the button to select the
desired function. The corresponding indicator light on the
display will switch on.
CLEANING ACTION
button : to select the desired
wash intensity.
ANTI ALLERGY RINSE
button : press to select the
desired rinse type.
SPIN button : press to reduce or completely exclude
the spin cycle - the value is indicated on the display.
TEMPERATURE button : press to decrease the tempe-
rature: the value will be shown on the display.
CHILD LOCK button : to activate the control panel
lock, press and hold the button for approximately 2
seconds. When the symbol is illuminated, the control
panel is locked (apart from the ON/OFF button). This
means it is possible to prevent wash cycles from being
modified accidentally, especially where there are children in
the home. To deactivate the control panel lock, press and
hold the button for approximately 2 seconds.
DELAY TIMER button : press to set a delayed start
time for the selected wash cycle. The delay time will be
shown on the display.
START/PAUSE button with indicator light: when the gre-
en indicator light flashes slowly, press the button to start a
wash cycle. Once the cycle has started the indicator light
will remain lit in a fixed manner. To pause the wash cycle,
press the button again; the indicator light will flash in an
orange colour. If the symbol is not illuminated, the door
may be opened. To start the wash cycle from the point at
which it was interrupted, press the button again.
Standby mode
This washing machine, in compliance with new energy sa-
ving regulations, is fitted with an automatic standby system
which is enabled after about 30 minutes if no activity is
detected. Press the ON-OFF button briefly and wait for the
machine to start up again.
Description of the washing machine
Control panel
TEMPERATURE
button
WASH
CYCLE
SELECTOR
buttons
Detergent dispenser drawer
FUNCTION
buttons
ON/OFF
button
SPIN SPEED
button
START/PAUSE
button with
indicator light
CHILD LOCK
button
DISPLAY
DELAY
TIMER
button
MY
CYCLE
button
CLEANING
ACTION
button
ANTI
ALLERGY
RINSE
button
GB
7
Display
The display is useful when programming the machine and provides a great deal of information.
The two upper strings A and B provide details of the wash cycle selected, the wash cycle phase in progress and all informa-
tion relating to the progress status of the wash cycle.
String C shows the time remaining until the end of the wash cycle in progress and, if a DELAYED START has been set, the
time remaining until the start of the selected wash cycle.
String D shows the maximum spin speed value (this depends on the selected wash cycle); if the wash cycle does not include
a spin cycle, the string remains unused.
String E shows the maximum temperature value which may be selected (this depends on the wash cycle used); if the tempe-
rature of the wash cycle cannot be modified, the string remains unused.
Indicator lights F correspond to the functions and light up when the selected function is compatible with the set wash cycle.
Door locked symbol
If the symbol is lit, this indicates that the washing machine door is blocked to prevent it from being opened accidentally. To
prevent any damage from occurring, wait for the symbol to switch itself off before opening the appliance door.
N.B.: if the DELAYE TIMER function has been activated, the door cannot be opened; pauses the machine by pressing the
START/PAUSE button if you wish to open it.
! The first time the machine is switched on, you will be asked to select the language and the display will automatically show
the language selection menu.
To select the desired language press the X and Y buttons; to confirm the selection press the Z button.
To change the language switch off the machine and press buttons X, Y, Z simultaneously until an alarm is heard: the
language-selection menu will be displayed again.
A
B
C
D
E
F
Z
X
Y
8
GB
Running a wash cycle
1. SWITCH THE MACHINE ON. Press the On/Off
button ; the text POWER ON will appear on the
display and the START/PAUSE indicator light will flash
slowly in a green colour.
2. LOAD THE LAUNDRY. Open the porthole door.
Load the laundry, making sure you do not exceed
the maximum load value indicated in the table of
programmes on the following page.
3. MEASURE OUT THE DETERGENT. Open the
detergent dispenser drawer and pour the detergent into
the relevant compartments as described in “Detergents
and laundry”.
4. CLOSE THE DOOR.
5. SELECT THE WASH CYCLE. Press one of the WASH
CYCLE SELECTOR buttons to select the required wash
cycle; the name of the wash cycle will appear on the
display. A temperature and spin speed is set for each
wash cycle; these may be adjusted. The duration of the
cycle will appear on the display.
6. CUSTOMISE THE WASH CYCLE. Use the relevant
buttons:
Modifying the temperature and/or spin speed.
The machine automatically selects the maximum
temperature and spin speed set for the selected wash
cycle; these values cannot therefore be increased.
The temperature can be decreased by pressing the
button, until the cold wash “OFF” setting is reached.
The spin speed may be progressively reduced by
pressing the button, until it is completely excluded
(the “OFF” setting). If these buttons are pressed again,
the maximum values are restored.
! Exception: if the 2 (60°)
(1st press of the button)
programme
is selected, the temperature can be increased up to a
value of 90°C.
Setting a delayed start.
To set a delayed start for the selected programme,
press the corresponding button repeatedly until the
required delay period has been reached. When this
option is enabled, the symbol lights up on the
display. To remove the delayed start function press the
button until the text “OFF” appears on the display.
Set the desired wash intensity.
Option makes it possible to optimise washing based
on the level of soil in the fabrics and on desired wash
cycle intensity.
Select the wash programme: the cycle will be
automatically set to Normal as optimised for garments
with an average level of soil (this setting is not applicable to
the “Wool” cycle, which is automatically set to “Delicate”).
For heavily-soiled garments press button until the
Super Wash” level is reached. This level ensures a
high-performance wash due to a larger quantity of
water used in the initial phase of the cycle and due to
increased drum rotation. It is useful when removing the
most stubborn stains.
It can be used with or without bleach. If you wish to
bleach the items insert the additional compartment
(4) into compartment 1. When pouring the bleach, be
careful not to exceed the “max” level marked on the
central pivot (see figure pag. 10).
For lightly-soiled garments or a more delicate treatment
of the fabrics, press button until the “Delicate” level
is reached.
The cycle will reduce the drum rotation to ensure
washing results are perfect for delicate garments.
Set the rinse type.
Option makes it possible to select the desired rinse
type for sensitive skin. Press the button once for theExtra
Rinselevel, which makes it possible to select an additional
rinse after the standard cycle rinse and remove all traces
of detergent. Press the button again for the Sensitive
Skin level, which makes it possible to select two additional
rinses to the standard cycle rinses; it is recommended for
very sensitive skin. When the button is pressed for the third
time, the Anti allergy Rinse level is set, thus allowing
the selection of 3 rinses in addition to the standard cycles
rinses. The option - started with cycles at a temperature of
4C - makes it possible to remove major allergens such
as pollen, cat and dog hair. With cycles at a temperature
higher than 4 a very good level of antiallergic protection is
achieved. Press the button again to go back to the Normal
Rinserinse type. If the current adjustment can be neither
set nor changed, the display will show Not allowed”.
Modifying the cycle settings.
• Pressthebuttontoenablethefunction;theindicator
light corresponding to the button will switch on.
• Pressthebuttonagaintodisablethefunction;the
indicator light will switch off.
! If the selected function is not compatible with the
programmed wash cycle, the indicator light will flash
and the function will not be activated.
! If the selected function is not compatible with
another function which has been selected previously,
the indicator light corresponding to the first function
selected will flash and only the second function will
be activated; the indicator light corresponding to the
enabled function will remain lit.
! The functions may affect the recommended load value
and/or the duration of the cycle.
7. START THE PROGRAMME. Press the START/PAUSE
button. The corresponding indicator light will become
green, remaining lit in a fixed manner, and the door will be
locked (the DOOR LOCKED symbol will be on). During
the wash cycle, the name of the phase in progress will
appear on the display. To change a wash cycle while
it is in progress, pause the washing machine using the
START/PAUSE button (the START/PAUSE indicator light
will flash slowly in an orange colour); then select the
desired cycle and press the START/PAUSE button again.
To open the door while a cycle is in progress, press
the START/PAUSE button; if the DOOR LOCKED
symbol is switched off the door may be opened. Press
the START/PAUSE button again to restart the wash cycle
from the point at which it was interrupted.
8. THE END OF THE WASH CYCLE. This will be
indicated by the text “END OF CYCLE” on the display;
when the DOOR LOCKED symbol switches off
the door may be opened. Open the door, unload the
laundry and switch off the machine.
! If you wish to cancel a cycle which has already begun,
press and hold the button. The cycle will be stopped
and the machine will switch off.
GB
9
Wash cycles and functions
Table of wash cycles
Wash functions
! If the selected function is not compatible with the
programmed wash cycle, the indicator light will flash
and the function will not be activated.
! If the selected function is not compatible with another
function which has been selected previously, the indica-
tor light corresponding to the first function selected will
flash and only the second function will be activated; the
indicator light corresponding to the enabled function will
remain lit.
Prewash
If this function is selected, the pre-wash cycle will run; this
is useful for removing stubborn stains.
N.B.: put the detergent in the relevant compartment.
Easy Iron
By selecting this function, the wash and spin cycles will be
modified in order to reduce the formation of creases.
At the end of the cycle the washing machine will perform
slow rotations of the drum; the “Easy Iron” and START/
PAUSE indicator lights will flash (orange) and the text “END
OF CYCLE” will appear on the display. To end the cycle,
press the START/PAUSE button or the “Easy Iron” button.
Eco Wash
The Eco Wash function saves energy by not heating the
water used to wash your laundry – an advantage both to
the environment and to your energy bill. Instead, intensified
wash action and water optimisation ensure great wash
results in the same average time of a standard cycle.
For the best washing results we recommend the usage of
a liquid detergent.
Wash cycles
Description of the wash cycle
Max.
temp.
(°C)
Max.
speed
(rpm)
Detergents
Max. load
(kg)
Residual dam-
pness %
Energy consum-
ption kWh
Total water lt
Cycle duration
Prewash
Wash
Bleach
Fabric
softener
CLEAN Plus
1
Anti Stain
(1st press of the button)
40° 1200
-
3 - - - 170’
1
Anti Stain Quick
(2nd press of the button)
40° 1200 -
-
2,5 - - - 60’
2
Standard Cotton 60°C (1st press of the button) (1): heavily soiled
whites and delicate colours.
60°
(Max. 90°)
1200
(3)
6 53 0,78 50 200’
2
Standard Cotton 40°C (2nd press of the button) (2): lightly soiled whites
and delicate colours.
40° 1200 -
6 53 0,65 65 170’
2
Standard Cotton 20°C
(3rd press of the button): lightly soiled whites and
delicate colours.
20° 1200 -
6 - - - 170’
3
Synthetics (Synths Resistant)
(1st press of the button): heavily soiled resi-
stant colours.
60° 800
3 44 0,70 40 105’
3
Synthetics (Synths Resistant)
(1st press of the button) (4): lightly soiled
resistant colours.
40° 800
3 44 0,47 38 95’
3
Synthetics (Synths Delicate)
(2nd press of the button): lightly soiled delicate colours. 40° 800
3 - - - 75’
SPECIALS
4
Fast Wash 30': to refresh lightly soiled garments quickly (not suitable for
wool, silk and clothes which require washing by hand).
30° 800 -
-
3 71 0,16 39 30’
M
My Cycle (Memory): allows for any wash cycle to be stored.
6
Bed & Bath: washes bathroom laundry and bedlinen. 60° 1200
-
6 - - - 100’
EXTRA CARE
7
Wool (Woolmark Platinum): for wool, cashmere, etc. 40° 800 -
-
1 - - - 65’
8
Delicates
30° 0 -
-
0,5 - - - 75’
Spin (1st press of the button) - 1200 - - - - 6 - - - 10’
Rinse (2nd press of the button) - 1200 - - -
6 - - - 36’
Pump out (3rd press of the button) - 0 - - - - 6 - - - 3’
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary according to factors such as
water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.
1) Test wash cycle in compliance with directive 1061/2010: set wash cycle “2” 60°C (1st press of the button).
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments
which can be washed at 60°C. The actual washing temperature may differ from the indicated value.
2) Test wash cycle in compliance with directive 1061/2010: set wash cycle “2” 40°C (2nd press of the button).
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments
which can be washed at 40°C. The actual washing temperature may differ from the indicated value.
3) At 60 °C the “Prewash” function cannot be selected.
For all Test Institutes:
2) Long wash cycle for cottons: set wash cycle “2” 40°C (2nd press of the button).
4) Long wash cycle for synthetics: set wash cycle “3” 6C (1st press of the button); temperature of 40°C (press TEMPERATURE button).
10
GB
Detergent dispenser drawer
Good washing results also depend on the correct dose of
detergent: adding too much detergent will not necessarily
result in a more efficient wash, and may in fact cause a
build up on the inside of your appliance and contribute to
environmental pollution.
! Use powder detergent for white cotton garments, for
pre-washing, and for washing at temperatures over 60°C.
! Follow the instructions given on the detergent packaging.
! Do not use hand washing detergents because these
create too much foam.
Open the detergent di-
spenser drawer and pour
in the detergent or washing
additive, as follows.
compartment 1:
Pre-wash detergent
(powder)
Before pouring in the deter-
gent, make sure that extra
compartment 4 has been removed.
compartment 2: Detergent for the wash cycle
(powder or liquid)
If liquid detergent is used, it is recommended that the
removable plastic partition A (supplied) be used for proper
dosage.
If powder detergent is used, place the partition into slot B.
compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow the grid.
extra compartment 4: Bleach
Preparing the laundry
•Dividethelaundryaccordingto:
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from whites.
•Emptyallgarmentpocketsandcheckthebuttons.
• Donotexceedthelistedvalues,whichrefertothe
weight of the laundry when dry: see “Table of wash
cycles”.
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1200 g
1 towel 150-250 g
Special wash cycles
Anti Stain: this programme is suitable to heavily-soiled
garments with resistant colours. It ensures a washing
class that is higher than the standard class (A class). When
running the programme, do not mix garments of different
colours. We recommend the use of powder detergent.
Pre-treatment with special additives is recommended if
there are obstinate stains.
Anti Stain Quick: this programme is ideal for washing
the most difficult daily stains in 1 hour. It is ideal for mixed
fabrics and coloured garments, caring for your clothes as
it washes.
Standard Cotton 20°C: ideal for lightly soiled cotton
loads. The effective performance levels achieved at cold
temperatures, which are comparable to washing at 40°,
are guaranteed by a mechanical action which operates at
varying speed, with repeated and frequent peaks.
Bed & Bath: use programme 6 to wash bed linen
and towels in one single cycle: it optimises softener
performance and helps you save time and energy. We
recommend the use of powder detergent.
Wool: the wool wash cycle of this machine has been
approved by The Woolmark Company for the washing of
wool garments labelled as “hand wash” provided that the
products are washed according to the instructions on the
garment label and those issued by the manufacturer of this
washing machine (M1128)
In UK, Eire, Hong Kong and India the Woolmark trade
mark is a Certification trade mark.
Delicates: use programme 8 to wash very delicate
garments with decorative features, such as diamantes and
sequins.
To wash silk garments and curtains select the cycle 8 and
set the “Delicate” level from option .
We recommend turning the garments inside out before
washing and placing small items into the special bag
for washing delicates. Use liquid detergent on delicate
garments for best results.
Load balancing system
Before every spin cycle, to avoid excessive vibrations and
to distribute the load in a uniform manner, the drum rotates
continuously at a speed which is slightly greater than the
washing rotation speed. If, after several attempts, the load
is not balanced correctly, the machine spins at a reduced
spin speed. If the load is excessively unbalanced, the
washing machine performs the distribution process instead
of spinning. To encourage improved load distribution and
balance, we recommend small and large garments are
mixed in the load.
M
AX
1
2
4
3
A
B
Detergents and laundry
GB
11
Troubleshooting
Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure
that the problem cannot be solved easily using the following list.
Problem:
The washing machine does not
switch on.
The wash cycle does not start.
The washing machine does not
take in water (the text “NO WATER,
CHECK SUPPLY” appears on the
display).
The washing machine continuously
takes in and
drains water.
The washing machine does not
drain or spin.
The washing machine vibrates a lot
during the spin cycle.
The washing machine leaks.
The machine is locked and the
display flashes, indicating an error
code (e.g. F-01, F-..).
There is too much foam.
Possible causes / Solutions:
• Theapplianceisnotpluggedintothesocketfully,orisnotmakingcontact.
• Thereisnopowerinthehouse.
• Thewashingmachinedoorisnotclosedproperly.
• TheON/OFFbuttonhasnotbeenpressed.
• TheSTART/PAUSEbuttonhasnotbeenpressed.
• Thewatertaphasnotbeenopened.
• Adelayedstarthasbeenset(see “Running a wash cycle”).
• Thewaterinlethoseisnotconnectedtothetap.
• Thehoseisbent.
• Thewatertaphasnotbeenopened.
• Thereisnowatersupplyinthehouse.
• Thepressureistoolow.
• TheSTART/PAUSEbuttonhasnotbeenpressed.
• Thedrainhoseisnotfittedataheightbetween65and100cmfromthefloor
(see “Installation”).
• Thefreeendofthehoseisunderwater(see “Installation”).
• Thewalldrainagesystemisnotfittedwithabreatherpipe.
If the problem persists even after these checks, turn off the water tap, switch
the appliance off and contact the Assistance Service. If the dwelling is on one of
the upper floors of a building, there may be problems relating to water drainage,
causing the washing machine to fill with water and drain continuously. Special
anti-draining valves are available in shops and help to avoid this inconvenience.
• Thewashcycledoesnotincludedraining:somewashcyclesrequirethedrain
phase to be started manually (see “Wash cycles and functions”).
• TheEASYIRONfunctionhasbeenactivated:Tocompletethewashcycle,
press the START/PAUSE button (see “Wash cycles and functions”).
• Thedrainhoseisbent(see “Installation”).
• Thedrainageductisclogged.
• Thedrumwasnotunlockedcorrectlyduringinstallation(see “Installation”).
• Thewashingmachineisnotlevel(see “Installation”).
• Thewashingmachineistrappedbetweencabinetsandwalls(see “Installation”).
• Thewaterinlethoseisnotscrewedonproperly(see “Installation”).
• Thedetergentdispenserdrawerisblocked(forcleaninginstructions,see “Care
and maintenance”).
• Thedrainhoseisnotfixedproperly(see “Installation”).
• Switchoffthemachineandunplugit,waitforapproximately1minuteandthen
switch it back on again.
If the problem persists, contact the Technical Assistance Service.
• Thedetergentisnotsuitableformachinewashing(itshoulddisplaythetext
“for washing machines” or “hand and machine wash”, or the like).
• Toomuchdetergentwasused.
12
GB
Before calling for Assistance:
Check whether you can solve the problem alone (see “Troubleshooting”);
Restarttheprogrammetocheckwhethertheproblemhasbeensolved;
Ifthisisnotthecase,contactanauthorisedTechnicalAssistanceCentreusingthetelephonenumberprovidedonthe
guarantee certificate.
! Always request the assistance of authorised technicians.
Have the following information to hand:
thetypeofproblem;
theappliancemodel(Mod.);
theserialnumber(S/N).
This information can be found on the data plate applied to the rear of the washing machine, and can also be found on the
front of the appliance by opening the door.
Service
CZ
13
Česky
Obsah
Instalace, 14-15
Rozbalení a vyrovnání do vodorovné polohy
Připojení k elektrické a k vodovodní síti
První prací cyklus
Technické údaje
Údržba a péče, 16
Uzavření přívodu vody a vypnutí elektrického napájení
Čištění pračky
Čištění dávkovače pracích prostředků
Péče o dvířka a buben
Čištění čerpadla
Kontrola přítokové hadice na vod
Opatření a rady, 17
Základní bezpečnostní pokyny
Likvidace
Manuální otevření dvířeku
Popis pračky, 18-19
Ovládací panel
Displej
Jak provést prací cyklus, 20
Programy a funkce, 21
Tabulka pracích programů
Funkce praní
Prací prostředky a prádlo, 22
Dávkovač pracích prostředků
Příprava prádla
Speciální programy
Systém automatického vyvážení náplně
Poruchy a způsob jejich odstranění, 23
Servisní služba, 24
CZ
FMSDN 623
Návod k použití
PRAČKA
14
CZ
! Je důležité uschovat tento návod tak, aby-
ste jej mohli kdykoli konzultovat. V případě
prodeje, darování nebo přestěhování pračky
se ujistěte, že zůstane uložen v blízkosti
pračky, aby mohl posloužit novému majiteli
při seznámení s její činností a s příslušnými
upozorněními.
! Pozor si přečtěte uvedené pokyny: ob-
sahují důležité informace týkající se instalace,
použití a bezpečnosti při práci.
Rozbalení a vyrovnání do vodoro-
vné polohy
Rozbalení
1. Rozbalte pračku.
2. Zkontrolujte, zda během přepravy
nedošlo k jejímu poškození. V případě, že
je poškozena, ji nezapojujte a obraťte se na
prodejce.
3. Odstraňte 4
šrouby chránící
před poškozením
během přepravy a
gumovou podložku
s příslušnou
rozpěrkou, které se
nacházejí v zadní
části (viz obrázek).
4. Uzavřete otvory po šroubech plastovými
krytkami z příslušenství.
5. Uschovejte všechny díly: v případě
opětovné přepravy pračky je bude třeba na-
montovat zpět.
! Obaly nejsou hračky pro děti!
Vyrovnání do vodorovné polohy
1. Pračku je třeba umístit na rovnou a pe-
vnou podlahu, aniž by se opírala o stěnu,
nábytek či něco jiného.
2. V případě, že
podlaha není do-
konale vodorovná,
mohou být případné
rozdíly vykompenzo-
vány šroubováním
předních nožek (viz
obrázek); Úhel sklo-
nu, naměřený na pra-
covní ploše, nesmí
přesáhnout 2°.
Dokonalé vyrovnání do vodorovné polohy
zabezpečí stabilitu zařízení a zamezí vzniku
vibrací a hluku během činnosti. V případě
instalace na podlahovou krytinu nebo na
koberec nastavte nožky tak, aby pod pračkou
zůstal dostatečný volný prostor pro ventilaci.
Připojení k elektrické a k vodo-
vodní síti
Připojení přítokové hadice vody
1. Připojte přívodní
hadici jejím
zašroubováním ke
kohoutku studené
vody s hrdlem se
závitem 3/4“ (viz
obrázek).
Před připojením
hadice nechte vodu
odtékat, dokud nebu-
de čirá.
2. Připojte přítokovou
hadici k pračce
prostřednictvím
příslušné přípojky
na vodu, umístěné
vpravo nahoře (viz
obrázek).
3. Dbejte na to, aby hadice nebyla příliš oh-
nutá ani stlačená.
! Tlak v rozvodu vody se musí pohybovat
v rozmezí hodnot uvedených v tabulce s
technickými údaji (viz vedlejší strana).
! V případě, že délka přítokové hadice ne-
bude dostatečná, obraťte se na specializo-
vanou prodejnu nebo na autorizovaný tech-
nický personál.
! Nikdy nepoužívejte již použité hadice.
! Používejte hadice z příslušenství zařízení.
Instalace
CZ
15
Připojení vypouštěcí hadice
Připojte vypouštěcí
hadici, aniž byste ji
ohýbali, k odpado-
vému potrubí nebo
k odpadu ve stěně,
který se nachází od
65 do 100 cm nad
zemí;
nebo ji uchyťte k
okraji umývadla či
vany a připevněte
vodicí držák
z příslušenství ke
kohoutu (viz obrá-
zek). Volný konec
vypouštěcí hadi-
ce nesmí zůstat
ponořený do vody.
! Použití prodlužovacích hadic se
nedoporučuje; je-li však nezbytné,
prodlužovací hadice musí mít stejný průměr
jako originální hadice a její délka nesmí
přesáhnout 150 cm.
Připojení k elektrické síti
Před zasunutím zástrčky do zásuvky se
ujistěte, že:
Je zásuvka uzemněna a že vyhovuje nor-
mám;
je zásuvka schopna snést maximální zátěž
odpovídající jmenovitému příkonu zařízení,
uvedenému v tabulce s technickými údaji
(viz vedle);
hodnota napájecího napětí odpovídá
údajům uvedeným v tabulce s technickými
údaji (viz vedle);
je zásuvka kompatibilní se zástrčkou
pračky. V opačném případě je třeba
vyměnit zásuvku nebo zástrčku.
! Pračka nesmí být umístěna venku – pod
širým nebem, a to ani v případě, že by se
jednalo o místo chráněné před nepřízní
počasí, protože je velmi nebezpečné vystavit
ji působení deště a bouří.
! Po denitivní instalaci pračky musí zásuvka
zůstat snadno přístupná.
! Nepoívejte prodlovací kabely a rozvodky.
65 - 100 cm
! Kabel nesmí být ohnutý ani stlačený.
! Výměna kabelu musí být svěřena výhradně
autorizovanému technickému personálu.
Upozornění! Výrobce neponese žádnou
odpovědnost za následky nerespektování
uvedených předpisů.
První prací cyklus
Po instalaci zařízení je třeba ještě předtím,
než je použijete na praní prádla, provést jeden
zkušební cyklus s pracím prostředkem a bez
náplně prádla nastavením pracího programu
„Samočištění“ (viz “Čištění pračky”).
Technické údaje
Model FMSDN 623
Rozmìry
šíøka 59,5 cm
výška 85 cm
hloubka 42,5 cm
Kapacita od 1 do 6 kg
Napájení
Viz štítek s technickými úda-
ji, aplikovaný na zarízení.
ipojení k
rozvodu vody
maximální tlak
1 MPa (10 bar)
minimální tlak
0.05 MPa (0.5 bar)
kapacita bubnu 40 litrù
Rychlost
odstøeïování
z do 1200 oèek za minutu
Kontrolní
programy
podle směrnic
1061/2010 a
1015/2010
program 2 60° (1. stisknutí
tlačítka); BAVLNA STAN-
DARD 60°.
program 2 40° (2. stisknutí
tlačítka); BAVLNA STAN-
DARD 40°.
Toto zaøízení odpovídá ná-
sledujícím normám Evropské
unie:
- 2004/108/CE (Elektroma-
gnetická kompatibilita)
- 2006/95/CE (Nízké napìtí)
- 2012/19/EU
16
CZ
Údržba a péče
Péče o dvířka a buben
Dvířka ponechte pokaždé pootevřená, aby
se zabránilo tvorbě nepříjemných zápachů.
Čištění čerpadla
Součástí pračky je samočisticí čerpadlo,
které nevyžaduje údržbu. Může se však stát,
že se v jeho vstupní části, určené k jeho
ochraně a nacházející se v jeho spodní části,
zachytí drobné předměty (mince, knoíky).
! Ujistěte se, že byl prací cyklus ukončen, a
vytáhněte zástrčku ze zásuvky.
Přístup ke vstupní části čerpadla:
1. pomo-
cí šroubováku
odstraňte krycí pa-
nel nacházející se v
přední části pračky
(viz obrázek);
2. Odšroubujte víko
jeho otáčením proti
směru hodinových
ručiček (viz obrázek):
vytečení malého
množství vody je
zcela běžným jevem;
3. dokonale vyčistěte vnitřek;
4. zašroubujte zpět víko;
5. namontujte zpět panel, přičemž se před
jeho přisunutím k zařízení ujistěte, že
došlo ke správnému zachycení háčků do
příslušných podélných otvorů.
Kontrola přítokové hadice na vodu
Stav přítokové hadice je třeba zkontrolovat
alespoň jednou ročně. Jsou-li na ní viditel-
né praskliny nebo trhliny, je třeba ji vyměnit:
silný tlak působící na hadici během pracího
cyklu by mohl způsobit její náhlé roztržení.
! Nikdy nepoužívejte již použité hadice.
Uzavření přívodu vody a vypnutí
elektrického napájení
Po každém praní uzavřete přívod vody.
Tímto způsobem dochází k omezení
opotřebení pračky a ke snížení nebezpečí
úniku vody.
Před zahájením čištění pračky a během
operací údržby vytáhněte zástrčku
napájecího kabelu z elektrické zásuvky.
Čištění pračky
• Vnější části a části z gumy se mohou
čistit hadrem navlhčeným ve vlažné vodě a
saponátu. Nepoužívejte rozpouštědla ani
abrazivní látky.
• Pračka je vybavena programem
„Samočištění“ vnitřních částí, který musí být
proveden bez jakéhokoli druhu náplně v
bubnu.
Prací prostředek (množství rovnající se
10% množství doporučeného pro částečně
znečištěné prádlo) nebo specické přídavné
prostředky pro čištění pračky budou moci být
použity jako pomocné prostředky v pracím
programu. Doporučuje se provést samočisticí
program každých 40 cyklů praní.
Pro aktivaci programu stiskněte současně
tlačítka A a B na dobu 5 sekund (viz obrázek).
Program bude zahájen automaticky a bude
trvat přibližně 70 minut. Cyklus je možné
ukončit stisknutím tlačítka START/PAUSE.
Čištění dávkovače pracích
prostředků
Vytáhněte dávkovač
jeho nadzvednutím
a vytažením směrem
ven (viz obrázek).
Umyjte jej pod prou-
dem vody; tento druh
vyčištění je třeba
provádět pravidelně.
1
2
BA
CZ
17
Opatření a rady
! Pračka byla navržena a vyrobena v souladu s platnými
mezinárodními bezpečnostním předpisy. Tato upozornění
jsou uváděna z bezpečnostních důvodů a je třeba si je
pozorně přečíst.
Základní bezpečnostní pokyny
• Toto zařízení bylo navrženo výhradně pro použití v
domácnosti.
Toto zařízení mohou používat děti od 8
let a osoby se sníženými fyzickými, sen-
zorickými nebo duševními schopnostmi
nebo osoby s nedostatečnými zkušenostmi
a znalostmi, když se nacházejí pod
náležitým dohledem nebo když byly
náležitě vyškoleny ohledně bezpečného
použití zařízení a uvědomují si související
nebezpečí. Děti si nesmí hrát se zařízením.
Děti nesmí provádět operace údržby a
čištění bez dohledu.
• Pračku mohou používat pouze dospělé osoby podle
pokynů uvedených v tomto návodu.
• Nedotýkejte se zařízení bosí nebo v případě, že máte
mokré ruce či nohy.
• Nevytahujte zástrčku ze zásuvky tahem za kabel, ale
uchopením za zástrčku.
• Neotvírejte dávkovač pracích prostředků během
činnosti zařízení.
• Nedotýkejte se odčerpávané vody, protože může mít
velmi vysokou teplotu.
• Nepokoušejte se o násilné otevření dvířek: mohlo
by dojít k poškození bezpečnostního uzávěru, který
zabraňuje náhodnému otevření.
• Při výskytu poruchy se v žádném případě nepokoušejte
o opravu vnitřních částí zařízení.
• Vždy mějte pod kontrolou děti a zabraňte tomu, aby se
přibližovaly k zařízení během pracího cyklu.
• Během pracího cyklu mají dvířka tendenci ohřát se.
• V případě potřeby přemísťujte pračku ve dvou nebo
ve třech a věnujte celé operaci maximální pozornost.
Nikdy se nepokoušejte zařízení přemísťovat sami, je
totiž velmi těžké.
• Před zahájením vkládání prádla zkontrolujte, zda je
buben prázdný.
Likvidace
• Likvidace obalových materiálů: při jejich odstranění
postupujte v souladu s místním předpisy a dbejte na
možnou recyklaci.
• Evropská směrnice 2012/19/EU o odpadních
elektrických a elektronických zařízeních stanovuje, že
staré domácí elektrické spotřebiče nesmí být od-
kládány do běžného netříděného domovního odpadu.
Staré spotřebiče musí být odevzdány do odděleného
sběru, a to za účelem recyklace a optimálního využití
materiálů, které obsahují, a z důvodu předcházení
negativním dopadům na lidské zdraví a životní
prostředí. Symbol “přeškrtnuté popelnice” na výrobku
vás upozorňuje na povinnost odevzdat zařízení po
Manuální otevření dvířek
V případě, že není možné otevřít dvířka s průzorem
z důvodu výpadku elektrické energie a hodláte pověsit
prádlo, postupujte následovně:
1. vytáhněte zástrčku ze
zásuvky elektrické sítě.
2. Zkontrolujte, zda je
hladina vody uvnitř zařízení
nižší, než je úroveň otevření
dvířek; v opačném případě
vypusťte přebytečnou
vodu vypouštěcí hadicí a
zachyťte ji do vědra, jak je
znázorněno na obrázku.
3. pomocí šroubováku
odstraňte krycí panel na-
cházející se v přední části
pračky (viz obrázek).
4. s použitím jazýčku označeného na obrázku potáhněte
směrem ven z dorazu plastové táhlo až do jeho uvolnění;
následně jej potáhněte směrem dolů a současně
otevřete dvířka.
5. namontujte zpět panel, přičemž se před jeho
přisunutím k zařízení ujistěte, že došlo ke správnému
zachycení háčků do příslušných podélných otvorů.
20
skončení jeho životnosti do odděleného sběru.
Spotřebitelé by měli kontaktovat příslušné místní
úřady nebo svého prodejce ohledně informací týka-
jících se správné likvidace starého zařízení.
18
CZ
Dávkovač pracích prostředků: slouží k dávkování
pracích prostředků a přídavných prostředků (viz „Prací
prostředky a prádlo“).
Tlačítko ON/OFF : zapte nebo vypněte pračku ktkým
stisknum tlítka. Kontrolka START/PAUSE pomalu blikající
zeleným světlem poukazuje na to, že je stroj zapnutý. Za
účelem vypnutí prky během praní je třeba det tlačítko
stisknu déle, přibl 3 sek.; krátké nebo hodné stisk-
nutí neumož vypnutí pračky. Vypnu zaříze během praní
zso zruše probíhaho pracího programu.
Tlačítka VOLBY PROGRAMŮ: sloí k nastave
požadovaného programu (viz “Tabulka pracích progra”).
Tlačítko PAMĚŤ: držte stisknuté toto tlačítko za účelem
uložení cyklu do paměti spolu s vlastními uživatelskými
nastaveními. Pro vyvolání cyklu, který byl předem
uložen do paměti, stiskněte tlačítko PAMĚŤ.
FUN tlačítka: stiskte tlítko kvůli vol padované
funkce. Na displeji se rozstí íslušná kontrolka.
Tlačítko
TYP PRANÍ
: jeho stisknutím můžete pro-
vést volbu požadované intenzity praní.
Tlačítko
TYP MÁCHÁNÍ
: jeho stisknutím můžete
provést volbu požadovaného máchání.
Tlačítko ODSTŘEĎOVÁNÍ : stiskněte za účelem
snížení nebo úplného vyloučení odstřeďování - hodnota
bude uvedena na displeji.
Tlačítko TEPLOTY : stiskněte za účelem snížení te-
ploty: Příslušná hodnota bude zobrazena na displeji.
Tlačítko ZABLOKOVÁNÍ TLAČÍTEK : aktivace
zablokování ovládacího panelu se provádí tak, že
podržíte stisknuté tlačítko přibližně na 2 sekundy.
Rozsvícená kontrolka poukazuje na to, že je ovládací
panel zablokován (sjimkou tlačítko ON/OFF). Tímto
způsobem se zamezí náhodným změnám programů,
zejména když jsou v domácnostiti. Zrušení zablokování
ovládacího panelu se provádí tak, že podržíte stisknuté
tlačítko přibližně na 2 sekundy.
Tlačítko ODLOŽENÉHO STARTU : stiskněte za
účelem nastavení odloženého startu zvoleného progra-
mu. Doba, o kterou bude start odložen, bude zobrazena
na displeji.
Tlačítko s kontrolkou START/PAUSE: když zelená
kontrolka začne pomalu blikat, stiskněte toto tlačítko pro
zahájení praní. Po zahájení cyklu se kontrolka rozsvítí
stálým světlem. Přejete-li si přerušit praní, opětovně
stiskněte tlačítko; kontrolka bude blikat oranžovým
světlem. Když symbol není rozsvícen, je možné
otevřít dvířka. Za účelem opětovného zahájení cyklu
z místa, v němž byl přerušen, opětovně stiskněte tlačítko.
Pohotovostní režim
Za účelem shody s novými předpisy souvisejícími s
energetickou úsporou je tato pračka vybavena systémem
automatického vypnutí (přechodu do pohotovostního
režimu – standby), který je aktivován po uplynutí 30 mi-
nut, když se pračka nepoužívá. Krátce stiskněte tlačítko
ON/OFF a vyčkejte na obnovení činnosti zařízení.
Popis pračky
Tlačítko s kontrolkou
START/PAUSE
Ovládací panel
Tlačítko
TEPLOTY
FUNKČNÍ
tlačítka
Tlačítko
ON/OFF
Dávkovač pracích prostředků
Tlačítka
VOLBY
PROGRAMŮ
Tlačítko
ODSTŘEĎOVÁNÍ
Tlačítko
ZABLOKOVÁNÍ
TLAČÍTEK
Displej
Tlačítko
ODLOŽENÉHO
STARTU
Tlačítko
PAMĚŤ
Tlačítko
TYP PRANÍ
Tlačítko
TYP
MÁCHÁNÍ
CZ
19
Displej
Displej slouží k naprogramování zařízení a poskytuje četné informace.
Ve dvou horních řetězcích A a B je zobrazen zvolený prací program, probíhající fáze praní a všechny informace o postu-
pu programu.
V řetězci C je zobrazena doba zbývající do konce probíhajícího pracího cyklu a v případě nastavení ODLOŽENÉHO
STARTU také doba chybějící do zahájení zvoleného programu.
V řetězci D je zobrazena maximální hodnota rychlosti odstřeďování, které zařízení může dosáhnout na základě zvo-
leného programu; když není odstřeďování součástí zvoleného programu, tento řetězec zůstane zhasnutý.
V řetězci E je zobrazena maximální hodnota teploty, kterou lze zvolit na základě zvoleného programu; když není nasta-
vení teploty součástí zvoleného programu, tento řetězec zůstane zhasnutý.
Kontrolky F se týkají funkcí a jsou rozsvícené, když je zvolená funkce kompatibilní s nastaveným programem.
Symbol Zablokovaných dvířek
Rozsvícení uvedeného symbolu poukazuje na zablokování dvířek kvůli zabránění jejich náhodnému otevření. Aby se
předešlo poškození, před otevřením dvířek je třeba vyčkat na zhasnutí uvedeného symbolu.
POZN.: Když je aktivována funkce ODLOŽENÉHO STARTU, nebude možné otevřít dvířka a pro jejich otevření bude
třeba přerušit činnost zařízení stisknutím tlačítka START/PAUSE.
! Při prvním zapnutí budete vyzváni, abyste provedli volbu jazyka, a poté bude na displeji automaticky zvoleno menu
volby jazyka.
Za účelem volby požadovaného jazyka stiskněte tlačítka X a Y a potvrďte voblu stisknutím tlačítka Z.
Když si přejete provést změnu jazyka, vypněte zařízení, stiskněte současně tlačítka X, Y, Z a držte je stisknutá, dokud
neuslyšíte akustický signál a neobjeví se menu pro volbu jazyka.
A
B
C
D
E
F
Z
X
Y
20
CZ
Jak provést prací cyklus
1. ZAPNUTÍ ZAŘÍZENÍ. Stiskněte tlačítko a na displeji
se zobrazí nápis ZAPNUTO; kontrolka START/PAUSE
bude pomalu blikat zelenou barvou.
2. NAPLŇTE PRAČKU PRÁDLEM. Otevřete dvířka.
Naplňte pračku prádlem a dbejte přitom, aby nedošlo
k překročení množství náplně, uvedeného v tabulce
programů na následující straně.
3. DÁVKOVÁNÍ PRACÍHO PROSTŘEDKU. Vytáhněte
dávkovač pracích prostředků a naplňte prací prostředek
do příslušných přihrádek způsobem vysvětleným v části
„Prací prostředky a prádlo“.
4. ZAVŘETE DVÍŘKA.
5. ZVOLTE PRACÍ PROGRAM. Stiskněte jedno z tlačítek
VOLBY PROGRAMŮ za účelem volby požadovaného
programu; název programu bude zobrazen na displeji;
ke zvolenému programu je přiřazena teplota a rychlost
odstřeďování, které se dají měnit. Na displeji bude
zobrazena doba trvání cyklu.
6. PROVEĎTE UŽIVATELSKÁ NASTAVENÍ PRACÍHO
CYKLU. Použijte íslušná tlítka:
Změňte teplotu a/nebo odstřeďování. Zařízení
automaticky zvolí teplotu a maximální rychlost
odstřeďování přednastavené pro zvolený program;
tyto hodnoty se nesmí zvyšovat. Stisknutím tlačítka
je možné postupně snížit teplotu až po praní ve
studené vodě „OFF“. Stisknutím tlačítka je možné
postupně snížit rychlost odstřeďování až po jeho úplné
vyloučení „OFF“. Další stisknutí tlačítek obnoví nastave
maximálních přednastavených hodnot.
! Výjimka: při volbě programu 2 (60°) (1. stisknutí tlačítka)
bude možné zvýšit teplotu až na 90°C.
Nastavte odložený start.
Pro nastavení odloženého startu zvoleného programu
stiskněte příslušné tlačítko až do dosažení požadované
doby odložení. Po zvolení této volitelné funkce se
zobrazí symbol . Zrušení odloženého startu se
provádí stisknutím tlačítka až do zobrazení nápisu OFF.
Nastavte požadovanou intenzitu praní.
Tlačítko umožňuje provést optimalizaci praní na
základě stupně znečištění tkanin a požadované intenzity
praní.
Zvolte program praní; cyklus bude automaticky
nastaven na úroveň „NORMÁLNÍ a bude provedena
jeho optimalizace pro středně znečištěné prádlo (toto
nastavení neplatí pro cyklus „Vlna“, který se automaticky
nastaví na úroveňJEMNÉ“).
Pro značně znečištěné prádlo stiskněte tlačítko
, dokud nebude nastavena úroveň „SUPER WASH“.
Tato úroveň zaručuje dokonalé praní díky použitítšího
množství vody v počáteční fázi cyklu a větší mechanický
pohyb a je užitečná pro odstranění nejodolnějších skvrn.
Může se používat s bělicím prostředkem nebo bez něj.
Když si přejete provést bělení, vložte přídavnou nádobku
4 z příslušenství do přihrádky 1. Při dávkovaní bělicího
prostředku nepřekračujte úroveň „max“, vyznačenou na
středovém čepu (viz obrázek na str. 22).
Pro mírně znečištěné prádlo nebo pro choulostivější
zacházení s látkami stiskněte tlačítko až po
dosažení úrovně „JEMNÉ“. Cyklus omezí mechanický
pohyb pro zajištění dokonalých výsledků praní u
choulostivého prádla.
Nastavte druh máchání.
Volitelfunkce umožňuje zvolit požadova druh
chá pro maximál péči o citlivé druhy pokožky. i
prvním stisknu tlítka bude nastavena úroveňEXTRA
CHÁ, kteumožní provést volbu přídavho
chá ve srovnání se standardním chám cyklu,
aby se odstranily všechny stopy po pracím prostředku.
i drum stisknutí tlačítka bude nastavena úrov
MÁCHÁNÍ CITLIVÁ PLEŤ“, která umožňuje provést volbu
dvou ídavných mác ve srovná se standardm
chám cyklu a doporučuje se pro citlií pokky.
i třem stisknutí tlačítka bude nastavena úrov
ANTIALERG. CHÁNÍ“ máchání, kteumožní provést
volbu 3 přídavch chání ve srovnání se standardním
chám cyklu. Tato volitelfunkce, kteje aktivona
i cyklech s teplotou 40 °C, umožňuje odstranit hlavní
alergeny, jako je kočičí i psí srst a pyl. Při teplotě nad
40 °C se dosahuje optimální úrovně protialergic
ochrany. Opětovným stisknutím tohoto tlítko sežete
vrátit na úrovchání „NORLNÍCHÁ.
Kdne možné prost požadované nastave
nebo změnit existující nastavení, na displeji se zobra
NEDOSTUPNÉ.
Změňte vlastnosti cyklu.
Stiskněte tlačítka aktivace funkce; dojde k rozsvícení
odpovídající kontrolky tlačítka.
Opětovným stisknutím můžete zvolenou funkci zrušit;
příslušná kontrola zhasne.
! V případě, že zvolená funkce není kompatibilní
s nastaveným pracím programem, příslušná kontrolka
začne blikat a funkce nebude aktivována.
! V případě, že zvolená funkce není kompatibilní s jinou
předem zvolenou funkcí, kontrolka první funkce bude
blikat a bude aktivována pouze druhá, přičemž kontrolka
zvolené funkce se rozsvítí stálým světlem.
! Funkce mohou změnit doporučenou náplň a/nebo
dobu trvání cyklu.
7. SPUSŤTE PROGRAM. Stiskte tlítko START/
PAUSE.íslušná kontrolka se rozsvítí stálým zeleným
světlem a dojde k zablokovádvířek (rozsvícený symbol
ZABLOKOVANÝCH DVÍŘEK ).hem praní se na
displeji zobrazev prohající ze. Za účelem změny
programu během probíhajícího cyklu erušte činnost
pračky stiknutím tlítka START/PAUSE (kontrolka
START/PAUSE bude pomalu blikat oranžovým stlem);
zvolte požadovaný cyklus a otov stiskněte tlačítko
START/PAUSE. Za účelem oteení dřek v pběhu
pracího cyklu stiskte tlítko START/PAUSE; když
bude symbol ZABLOKOVANÝCH DVÍŘEK zhasnutý,
bude možné oteít dvířka. Otovm stisknutím tlačítka
START/PAUSE znovu uveďte do činnosti pra program
z bodu, ve ktem byl přeren.
8. UKONČENÍ PROGRAMU. Bude oznámeno zobrazením
nápisu „KONEC CYKLU“ na displeji. Po zhasnutí
symbolu ZABLOKOVANÝCH DVÍŘEK bude možné
otevřít dvířka. Otevřete dvířka, vyložte prádlo a vypněte
zařízení.
! Přejete-li si zrušit již zahájený cyklus, znovu dlouze
stiskněte tlačítko . Cyklus bude přerušen a dojde k
automatickému vypnutí zařízení.
1 / 1

HOTPOINT/ARISTON FMSDN 623B CZ Užívateľská príručka

Kategória
Práčky
Typ
Užívateľská príručka