Fieldmann FZP 2005-E Používateľská príručka

EN

FZP 2005-E

2

FZP 2005-E

English ................................................................................................................................................................................3–20

Čeština ............................................................................................................................................................................ 21–38

Slovenčina .................................................................................................................................................................... 39–56

Magyarul ....................................................................................................................................................................... 57–74

Polski ................................................................................................................................................................................ 75–92

EN

ELECTRIC CHAIN SAW USER'S MANUAL

3

Table of Contents

Electric Chain Saw

USER'S MANUAL

TABLE OF CONTENTS

1. GENERAL SAFETY INSTRUCTIONS ..........................................................................................................................4

2. SYMBOLS ...........................................................................................................................................................................5

3. SAFETY INSTRUCTIONS ................................................................................................................................................7

4. DESCRIPTION OF THE CHAIN SAW .......................................................................................................................9

5. INSTALLING THE GUIDE BAR AND CHAIN .......................................................................................................10

6. FILLING THE CHAIN SAW OIL TANK..................................................................................................................... 11

7. OPERATING THE CHAIN SAW ................................................................................................................................11

8. CHAIN BRAKE ................................................................................................................................................................12

9. ADJUSTING THE CHAIN TENSION ........................................................................................................................13

10. USING THE CHAIN SAW ............................................................................................................................................13

11. CUTTING...........................................................................................................................................................................13

12. CLEANING AND MAINTENANCE .........................................................................................................................15

13. SHARPENING THE SAW CHAIN .............................................................................................................................16

14. REPLACING THE SAW CHAIN ................................................................................................................................17

15. STORAGE .........................................................................................................................................................................18

16. TECHNICAL SPECIFICATIONS .................................................................................................................................19

17. DISPOSAL ........................................................................................................................................................................19

18. DECLARATION OF CONFORMITY ......................................................................................................................20

EN 4

FZP 2005-E

General safety instructions

1. GENERAL SAFETY INSTRUCTIONS

Important safety notice

Carefully unpack the product and take care not to throw away any part of the packaging before you ﬁ nd all

the parts of the product.

Store the product in a dry place out of reach of children.

Read all warnings and instructions. Not following warnings or instructions may lead to injury by electrical

shock, a ﬁ re and/or serious injuries.

Packaging

The product is packed in a package that prevents damage during transport. This package is a resource and so

can be handed over for recycling.

Operating instructions

Before you start working with the power tool, read the following safety and usage instructions. Understand the

operating elements and the correct use of the power tool. Keep the user’s manual in a safe place where it can be

easily retrieved for future use. Save the original packaging, including the internal packing material, warranty card

and proof of purchase receipt, at least for the duration of the warranty. If you need to ship this power tool, pack it

in the original cardboard box to ensure maximum protection during shipping or transport (e.g. when moving or

when you need to send this power tool for repair to a service centre).

Note: If you hand over the power tool to somebody else, do so together with this user's manual.

Following the instructions in the included user's manual is a prerequisite for the proper use of the power tool.

The user's manual also contains operating, maintenance and repair instructions.

The manufacturer takes no responsibility for accidents or damages resulting from not

following the instructions in this manual.

EN

ELECTRIC CHAIN SAW USER'S MANUAL

5

Symbols

2. SYMBOLS

Do not expose the power tool to rain.

Before using the power tool, carefully read the

user's manual.

In the event that the power cord is damaged,

immediately disconnect it from the power supply.

When working, always use a safety helmet,

safety glasses and ear protection.

Careful: danger of kickback.

EN 6

FZP 2005-E

Symbols

DANGER! Do not use the power tool if there are

children, other persons or animals in your vicinity.

While working use protective gloves.

Use solid insulating work footwear.

Use hearing protection.

Use work gloves.

Be careful of falling branches.

EN

ELECTRIC CHAIN SAW USER'S MANUAL

7

Safety Instructions

3. SAFETY INSTRUCTIONS

ATTENTION!

Acquaint yourself with all warnings and safety instructions and with operation instructions for the power

tool.

ATTENTION!

Not adhering to warnings or safety instructions may result in injury by electrical shock, a ﬁ re and/or serious

injury.

ATTENTION!

Store all warnings and safety instructions in a practical location for future reference.

Note: The term "power tool" in all hereafter provided warnings is deﬁ ned as an electric power tool powered

from the power grid (via a ﬂ exible power cord).

Safety in the work area

Keep the work area tidy and well illuminated. Untidiness and dark locations in the workplace are sources of

accidents.

Do not use the power tool in environments where there is a explosion hazard, where there are ﬂ ammable

liquids, gases or dust. The power tool generates sparks which could ignite dust or vapours.

When using the power tool, prevent children and other persons access to the power tool. If you become

distracted, you may lose control over the power tool.

Safety when working with power tools

The plug on the ﬂ exible power cord must correspond to the power socket outlet. Never modify the plug in any

way. Never use any socket adapters with power tools that have a safety earth grounding connection. Plugs

that are not damaged by modiﬁ cations and that correspond to the power socket will limit the danger of injury

by electrical shock.

Prevent your body from coming into contact with grounded objects, such as pipes, central heating radiators,

stoves and refrigerators. The risk of injury by electrical shock is greater when your body is connected to the

ground.

Do not expose the power tool to rain, dampness or wetness. The entry of water into the power tool increases

the danger of injury by electrical shock.

Do not use the ﬂ exible power cord for other purposes. Never carry or pull the power tool by its power cord or

pull the plug out of the socket by the power cord. Protect the power cord against heat, grease, sharp edges

and moving parts. Damaged or tangled power cords increase the danger of injury by electrical shock.

If the power tool is used outdoors, use an extension cord suitable for outdoor use. Using extension cords

designed for outdoor use limits the risk of injury by electrical shock.

If you will be using the power tool in a damp environment, use a residual current device (RCD) in the power

supply circuit. The use of a residual current device reduces the risk of injury by electrical shock.

Note: The "residual current device" (RCD) may be substituted for by the term "ground fault circuit

interrupter" (GFCI) or "earth leakage circuit breaker" (ELCB).

EN 8

FZP 2005-E

Safety Instructions

Safety of people

When working with the power tool, always stay alert, watch what you are doing and use common sense.

Do not use power tools if you are tired or under the inﬂ uence of drugs, alcohol or medication. A moment of

carelessness when working with power tools may result in serious injury.

Use personal protective aids. Always use eye protection. Use protective aids, e.g. respirator, safety footwear

with anti-slip soles, hard head cover or hearing protection appropriately to the work conditions; they reduce

the risk of injury to persons.

Avoid accidentally starting up the power tool. Before connecting to a power source, before connecting the

battery, before storage or before carrying the power tool, make sure that the start/stop trigger is in the off

position. Carrying the power tool with a ﬁ nger on the trigger or connecting the power tool’s plug with the

trigger engaged may cause an accident.

Remove all adjustment tools and spanners before turning on the power tool. An adjustment tool or spanner

left attached to a rotating part of the power tool may result in injury to persons.

Only work in locations that you can reach safely. Always maintain a stable stance and balance.

In this way you will have better control over the power tool in unexpected situations.

Dress in an appropriate manner. Do not wear loose clothing or jewellery. Make sure that your hair, clothing

and gloves are at a sufﬁ cient distance from moving parts. Loose clothing, jewellery and long hair may

become caught in the moving parts.

If there is equipment available for the extraction and collection of dust, make sure that such equipment is

connected and used correctly. The use of such equipment may limit the danger posed by the created dust.

Using power tools and their maintenance

Do not overload the power tool. Only use power tools that are appropriate for the work being performed.

Appropriate power tools for the given task will do the job better and more safely.

Do not use power tools that cannot be turned on and off with a switch. Any electric power tools that cannot

be controlled using a switch are dangerous and must be repaired.

Before adjusting the power tool, before replacing accessories or if you will not be using the power tool, pull

the power plug out of the power socket. These preventative safety measures limit the danger of accidentally

turning on the power tool.

When not used, store the power tool out of children’s reach and do not permit person not acquainted with

the power tool or these instructions to use the power tool. A power tool in the hands of inexperienced users is

dangerous.

Perform maintenance on the tool. Check the adjustment of moving parts and their movement, focus on

cracks, broken parts or any other circumstances that may threaten the proper operation of the power tool.

If the power tool is damaged, have it repaired before using it again. Many accidents are caused by

insufﬁ ciently maintained power tools.

Keep cutting power tools clean and sharp. Correctly maintained and sharpened cutting power tools are less

likely to get stuck on material or to jam and they are also easier to control.

Use power tools, accessories, working tools, etc. in accordance with these instructions and in such

a manner as prescribed for the speciﬁ c power tool with respect to the given work conditions and the type

of work being carried out. Using power tools for tasks other than for which they are designed may lead to

dangerous situations.

Service

Have your power tool repaired by a qualiﬁ ed person that will use original spare parts. In this manner, the

same level of safety will be ensured as before the repair of the power tool.

EN

ELECTRIC CHAIN SAW USER'S MANUAL

9

Storage

only move or store the power tool with the protective cover attached

carefully clean and perform appropriate maintenance before storing the power tool

before transporting the power tool, secure it against oil leakage, damage or injury hazard

4. DESCRIPTION OF THE CHAIN SAW

1. Power cord safety hook

2. Power cord fastening hole

3. Rear handle

4. Front handle

5. Safety brake

6. Chain tensioning wheel

7. Sprocket cover fastening knob

8. Chain

9. Guide bar

10. Sprocket cover

11. Oil tank cap

12. Start/stop trigger

13. Trigger safety lock

14. Window for checking the oil level

Fig. 1

Included contents:

Electric chain saw, 40 cm guide bar, chain, plastic guide bar cover, mounting wrench.

Safety instructions | Description of the chain saw

EN 10

FZP 2005-E

5. INSTALLING THE GUIDE BAR AND CHAIN

ATTENTION!

The chain saw must be disconnected from the

power grid.

ATTENTION!

Always wear protective gloves when installing

and inspecting the chain to prevent injury from the

sharp cutting edges on the chain.

The safety brake lever (ﬁ g. 1 point 5) must be

disengaged (pull it towards the top handle)

Loosen the sprocket cover fastening knob

(ﬁ g. 1, point 7) and remove the sprocket cover

(ﬁ g. 1, point 10)

Put the chain on the chain drive sprocket (ﬁ g. 2,

point 1), then put the guide bar on to the guide bolt

(ﬁ g. 2, point 2) and place the chain into the guiding

groove.

ATTENTION!

Make sure that the chain is installed correctly; the

direction must correspond to the arrow markings

on the chain and guide bar.

Put on the sprocket cover and fasten it using the

sprocket cover fastening knob (ﬁ g. 3)

Do not fully tighten the knob, it would not be possible

to tension the chain

Tension the chain using the tensioning wheel

(ﬁ g. 3, point 1).

For tensioning it is necessary to hold down the

sprocket cover fastening knob (see ﬁ g. 5)

ATTENTION!

The chain is correctly tensioned if it is possible

to lift chain off the guide bar and its height in the

horizontal position in the middle of the guide bar is

3 to 4 mm.

Installing the guide bar and chain

Fig. 2

Fig. 3

Fig.4

1

EN

ELECTRIC CHAIN SAW USER'S MANUAL

11

6. FILLING THE CHAIN SAW OIL TANK

ATTENTION!

A new chain requires a certain running-in period, which is usually 5 minutes. The lubrication of the chain

is very important during this phase. After this running-in period, check the chain tension and readjust if

necessary.

The oil tank on the supplied chain saw is empty. Fill this oil tank with oil prior to ﬁ rst use of this chain saw.

Only use oil speciﬁ ed for total-loss lubrication

Screw off the oil tank cap (ﬁ g. 1, point 11).

Pour the oil into the tank (take care to prevent the oil from becoming dirty while ﬁ lling the tank).

Screw on the oil tank cap

ATTENTION!

Do not use oil that has already been used or processed because this could damage the oil pump. Only use

oil speciﬁ ed for total-loss lubrication

7. OPERATING THE CHAIN SAW

Securing the extension cord.

ATTENTION!

When working with this chain saw, only use extension cords designed for outdoor use. The wire cross-

sections on the extension cord must be at least 1.5 mm2.

To ensure safe operation of this chain saw, it is necessary to secure the power cord in place. Bend the power

cord approximately 20 cm before the socket. Thread the bend through the hole (ﬁ g. 1, point 2) in the rear

handle and ﬁ t it into the hook. (ﬁ g. 1, point 1)

ATTENTION!

If you use an extension cord longer than 30 m, the power of the chain saw will be reduced

Turning on / off

ATTENTION!

The voltage in the power grid must corresponds to the voltage on the rating label of the chain saw.

ATTENTION!

Hold the chain saw ﬁ rmly with both hands when starting and working with it

Starting

Press the trigger safety lock button located on the left above the start/stop trigger and then press the start/

stop trigger (ﬁ g. 1, point 13) . When started, the chain saw will run at maximum speed.

ATTENTION!

If the chain saw does not start, disengage the brake lever (ﬁ g. 1, point 5).

Filling the chain saw oil tank | Operating the chain saw

EN 12

FZP 2005-E

Operating the chain saw | Chain brake

Turning off

Release the start/stop trigger (ﬁ g. 1, point 12).

ATTENTION!

The chain saw is equipped with a safety motor brake, which will immediately stop the chain when the start/

stop trigger is released. If the chain does not immediately come to a stop when the trigger is released,

please contact an authorised service centre without delay.

Checking chain lubrication

ATTENTION!

Adhere to safety provisions and prevent the guide bar from coming into contact with the surface of the

terrain. Use this power tool safely and maintain a minimum distance of 20 cm from the ground.

Before starting work, check the chain lubrication and the amount of oil in the oil tank. Start the chain saw

and hold it above the ground. If you see a growing oil stain then chain lubrication is working properly. If there

are no oil stains on the ground, clean the oil outlet, the top chain tensioning hole and the oil lines or contact

an authorised service centre.

8. CHAIN BRAKE

This chain saw is equipped with an automatic brake that stops the chain in the event of kickback. The brake

is automatically engaged as soon as the force of inertia acts on the ballast located inside the brake box.

The chain brake may also be engaged manually when the brake lever (ﬁ g. 1, point 5) is moved downwards

towards the guide bar. The activation of the brake stops the chain movement within 0.12 seconds.

Checking the working order of the brake.

Check that the brake works properly before every use.

Place the running chain saw on to the ground and for 1 to 2 seconds leave it at full speed.

Push the brake lever (ﬁ g. 1, point 5) forward. The chain should stop immediately.

ATTENTION!

If the chain stops slowly or does not stop at all, do not use the chain saw and contact an authorised service

centre.

If you wish to disengage the brake, pull the brake lever towards the top handle (ﬁ g. 1, point 4) so that you

hear the typical sound for the disengagement of the brake.

ATTENTION!

Check that the chain brake is in order. A correctly functioning chain brake will protect you against potential

injury, which could result from kickback. If the brake is not working properly, have it adjusted or repaired at

an authorised service centre.

EN

ELECTRIC CHAIN SAW USER'S MANUAL

13

9. ADJUSTING THE CHAIN TENSION

ATTENTION!

Due to the effect of higher temperatures, during operation the saw chain has a tendency to lengthen.

A longer chain becomes loose and could slide off the guide bar.

ATTENTION!

This chain saw has a chain tensioning system that does not require any tools.

Loosen the sprocket cover fastening knob (ﬁ g. 1, point 7).

Make sure that the chain is seated in the guiding groove of the guide bar.

Turn the chain tensioning wheel (ﬁ g. 1, point 6) clockwise to tension the chain (ﬁ g. 4). It should be possible

to lift a correctly tensioned chain in the middle of the guide bar in the horizontal position to a height of

approximately 3 to 4 mm).

Tighten the sprocket cover fastening knob (ﬁ g. 1, point 7).

ATTENTION!

Do not tension the chain excessively. Excessive tension of a warm chain may result in excessively tension

when it cools down.

10. USING THE CHAIN SAW

Before starting any kind of work, thoroughly acquaint yourself with the sections describing the safety

instructions for the operation of the chain saw. We recommend that you acquire experience by practising on

waste wood. In this way you will learn about the operating parameters of this chain saws.

Always adhere to safety instructions.

Only use this chain saw for cutting wood. Cutting any other materials is forbidden.

The vibration intensity and type of kickback on this chain saws depends on the type of wood being cut.

Do not use this chain saw as a lever for lifting, moving or splitting material.

If the chain jams in the material that is being cut, stop the chain saw and knock a wooden or plastic wedge

into the cut to release the chain. Restart the chain saw and carefully commence cutting.

11. CUTTING

ATTENTION!

Before proceeding, please read the chapter “Safety instructions”. We recommend that you gain experience

by cutting smaller logs. In this way you will also get to know the chain saw.

Always adhere to safety instructions. The chain saw may only be used for cutting wood.

It is forbidden to cut any other materials. Vibrations and kickback differ for various materials. Do not use the

chain saw as a lever for lifting, moving or splitting material. It is forbidden to attach any parts or jigs other

than those speciﬁ ed in the technical documentation.

Adjusting the chain tension | Using the chain saw | cutting

EN 14

FZP 2005-E

It is not necessary to push the chain saw into the cut. When the motor is running at full speed, push the chain

saw down lightly.

If the chain jams in the cut, do not attempt to free it by pulling, rather stretch open the cut using a wedge or

crowbar.

Safety brake (protection against kickback)

This chain saw is equipped with an automatic chain brake that, if it works correctly, immediately stops the

chain in the event of kickback. It is necessary to check the working order of the chain brake before every use

of the chain saw. Run the chainsaw at full speed for 1 - 2 seconds and then tilt the front protective cover. The

chain must stop immediately even when the motor is running at high speed. If the chain stops slowly or does

not stop at all, please contact an authorised service centre.

It is extremely important to check the working order of the chain brake and the sharpness of the chain before

every use to ensure that the necessary level of safety in the event of a kickback is maintained. Removing

safety accessories, incorrect maintenance or when using unsuitable guide bars or chains may, in the event

of kickback, result in serious injuries.

Cutting trees

Decide about the direction in which the tree will fall, respecting

the wind direction, incline angle of the tree and location of the

branches, and consider all other factors before cutting.

The area around the tree must be clear, without obstacles, and

must enable a stable stance. The escape route must be passable.

Cut a wedge into one third of the tree’s diameter on the side to

which the tree should fall. (see ﬁ g. Cutting trees, point 1)

From the opposite direction perform a separation cut at a level

above the wedge cut. (see ﬁ g. Cutting trees, point 2)

The tree will fall in the direction towards the wedge cut.

(see ﬁ g. Cutting trees, point 3)

ATTENTION!

When cutting trees, inform other people in the area about the potential danger. Cutting trees requires

experience and we do not recommend performing this task without the necessary experience.

Cutting logs

ATTENTION!

Always maintain a stable stance. Do not step on logs.

ATTENTION!

Before starting work, check that all components are in their place and that all nuts and bolts are tightened.

The log being cut may roll away. Especially when cutting on a slope, always stand above the log being cut.

Prevent kickback of the saw by following the instructions in chapter “Safety instructions”.

Before starting work, assess the direction of the force causing the cut trunk to bend. The ﬁ nal cut needs to

always be done from the opposite side of where the bending force is acting to prevent the guide bar from

being clamped inside the cut.

Only carry the chain saw with the motor turned off and the guide bar protected by the protective cover.

Cutting

Cutting trees

EN

ELECTRIC CHAIN SAW USER'S MANUAL

15

Log lying on the ground

Cut it halfway through, then roll it over and complete the cut

from the other side.

Log above the ground

In part “A” make a cut from below to a third of the log and

then complete the cut from above. In part “B” make a cut

from above to a third of the log and then complete the cut

from below.

Removing a fallen tree

First ﬁ nd out to which side the branch is bent. Then make the

initial cut from the side of the bend and then complete the

cut from the opposite side.

ATTENTION!

A bent branch may spring up.

12. CLEANING AND MAINTENANCE

Cleaning the body of the chain saw

Keep the body of the chain saw clean. When cleaning, use a soft cloth dipped in a soap solution. Use this cloth to

meticulously clean the body of the chain saw.

Maintaining the guide bar

Most problems with the guide bar arise due to uneven wear.

Uneven wear occurs mainly as a result of an incorrectly

sharpened chain or an incorrectly set depth gauge. When

the guide bar is worn out unevenly, the guiding groove is

widened (see Picture). The result is a rattling chain and

rivets falling off.

The chain saw cannot be used for straight cuts. In such

a case, replace the guide bar for a new one.

Always check the condition of the guide bar before

sharpening the chain. Using a worn out or damaged guide

bar is very dangerous. Using a worn out or damaged guide

bar will result in damage to the chain. Cutting with such

a power tool will also be much more difﬁ cult and

demanding.

Cutting | Cleaning and maintenance

Guide bar

groove

Guide bar

Standard

guide bar

Guide bar with

uneven wear

EN 16

FZP 2005-E

Cleaning and maintenance | Sharpening the saw chain

Normal maintenance of the guide bar

Remove the guide bar from the body of the chain saw.

Regularly remove sawdust from the guide bar groove. For cleaning use a spatula or a wire.

Clean oily grooves at the end of every work day.

Replace the guide bar if:

• it is bent or cracked

• its groove is very damaged or worn out

Note: To replace the guide bar, follow the instruction contained in this user's manual. You will ﬁ nd the

correct guide bar type in the technical speciﬁ cations.

13. SHARPENING THE SAW CHAIN

Keep the saw chain sharp. Cutting will be signiﬁ cantly faster and most importantly safer. A blunt saw chain

increases wear on the sprocket, guide bar, chain and motor. If you need to push on the saw and only sawdust

with a few splinters are produced then this means that the chain is blunt.

For this task, we recommend that you contact an authorised service centre

Equipment necessary for sharpening a saw chain

Round ﬁ le as per technical speciﬁ cations

Depth gauge

File guide

Vice

Medium-size ﬂ at ﬁ le

Sharpening the teeth on the chain

Use the ﬁ le guide set at an angle of 30° (mark A, see ﬁ gure).

Set the saw chain tension to the correct level.

Fasten the guide bar in a vice so that you have the chain in a stable

position.

Note: Do not fasten the chain itself.

Push the round ﬁ le, inserted in the ﬁ le guide, into the groove

between the top plate and the depth gauge on the chain. The chain

should be touching both the top plate as well as the depth gauge

(see ﬁ gure)

Note: File in the middle of the guide bar.

Note: In the ﬁ gure you can see the position of the ﬁ le guide and

the direction for ﬁ ling the teeth on the left side of the chain.

Place the ﬁ le guide at the required angle (mark A, see ﬁ gure).

Check that the mark is at 30° on the ﬁ le guide aligned with the centre of the guide bar. This will ensure that

you will ﬁ le at an angle of 30°.

EN

ELECTRIC CHAIN SAW USER'S MANUAL

17

File the tooth in the direction from inside out (in direction B, see ﬁ gure) until it is sharp. File only in this

direction.

Note: Two to three passes of the ﬁ le should be sufﬁ cient to sharpen the tooth.

Filing the depth gauge

As a result of sharpening the teeth on the chain, the depth gauge

tolerance is reduced. After every second or third sharpening, it is

necessary to adjust the depth gauge setting.

Place the depth gauge adjustment jig (see ﬁ g., point 1) ﬁ rmly

on the top edge of two teeth. Make sure that the groove of the

jig is in the groove of the depth gauge (see ﬁ g., point 2.)

Use a medium-sized ﬂ at ﬁ le (see ﬁ g., point 3).

File the depth gauge (see ﬁ g., point 4) to the level of the depth

gauge adjustment jig.

Remove the depth gauge adjustment jig. Using a ﬂ at ﬁ le,

round the front edge of the depth gauge (see ﬁ gure). When

ﬁ ling, adhere to the prescribed values (see ﬁ g., point 5).

Note: After the chain has been sharpened by hand several

times, have the saw chain sharpened at an authorised

service centre or sharpen it on a special sharpening

machine. This will renew the even sharpness of all teeth.

14. REPLACING THE SAW CHAIN

ATTENTION!

When replacing the saw chain, do not clamp the chain saw or the guide bar in a vice.

Always replace the chain if the teeth are excessively worn out and they cannot be sharpened or if the chain

snaps. Use only an original spare chain according to the speciﬁ cations in this user’s manual. When replacing

the saw chain, always also replace the cogged wheel of the sprocket. This will ensure the correct position of the

chain during movement. (Note: You will ﬁ nd the speciﬁ cations of the correct chain type and the cogged wheel in

the technical speciﬁ cations.)

Sharpening the saw chain | Replacing the saw chain

4

2

1

3

50,6 mm

EN 18

FZP 2005-E

Replacing the saw chain | Storage

Loosen and remove the bar guide bolt.

Remove the sprocket cover.

Remove the saw chain.

Wind the new chain around the cogged wheel, then along the top

groove of the guide bar and around the guide bar nose.

Note: Check that the saw teeth are facing in the correct direction.

Put on the chain so that the teeth on the top side of the guide bar

are facing towards the guide bar nose (see ﬁ gure).

Before placing the sprocket cover into position, check that the chain

tensioning pin is inserted into the adjustment hole on the guide bar.

Put the sprocket cover back on to the body of the chain saw.

Fasten the sprocket cover using the guide bar bolt.

ATTENTION!

Only tighten the bolt by hand.

Adjust the tension of the saw chain.

Tighten the guide bar bolt.

ATTENTION!

Check that you have not placed the saw chain on the guide bar in the opposite direction.

Otherwise, the chain saw will exhibit excessive vibrations and will not cut.

15. STORAGE

If you will not use the chain saw for longer than 30 days, proceed as follows.

Drain the oil tank.

Remove and clean out the guide bar and chain. Submerge the guide bar and chain into a kerosene-based or

soap cleaning solution.

Then dry the guide bar and the chain.

Put the chain into a container ﬁ lled with oil. This will prevent it from corroding.

Gently coat the guide bar with oil.

Wipe the body of the chain saw with a cloth. When cleaning, use a soft cloth dipped in a soap solution.

Store the chain saw

• In higher shelves or in locked areas out of children’s reach

• in a dry location

EN

ELECTRIC CHAIN SAW USER'S MANUAL

19

16. TECHNICAL SPECIFICATIONS

Power input 2000 W

Voltage/frequency 230 V - 240 V / 50 Hz

Chain pitch 3/8“

Guiding groove width 1.3 mm

Number of chain links 56 links

Length of the guide bar 40 cm

File diameter 4 mm

Cutting speed 13 m/s

Oil tank capacity 120 ml

Weight (with guide bar and chain) 5.5 kg

Level of acoustic power LWA measured 112 dB(A)

Vibration (k=1.5) 6.970 m/s

User's manual in original language.

17. DISPOSAL

INSTRUCTIONS AND INFORMATION REGARDING THE DISPOSAL OF USED

PACKAGING MATERIALS

Dispose of used packaging material at a site designated for waste in your municipality.

The machine and its accessories are manufactured from various materials, e.g. metal and

plastic.

Take damaged parts to a recycling centre. Inquire at the relevant government department.

Changes in the text, design and technical speciﬁ cations may be made without prior notice and we reserve

the right to make these changes.

Technical specifications | Disposal

EN 20

FZP 2005-E

Declaration of Conformity

18. DECLARATION OF CONFORMITY

Manufacturer:

FAST ČR, a.s.

Černokostelecká 2111, 100 00 Praha 10, Czech Republic

VAT no: CZ26726548

Product / brand: ELECTRICAL CHAIN SAW / FIELDMANN

Type / model: FZP 2005 E as factory model HY6107H160

230V, 2000W

The product is inline with directives and regulations listed below:

Electromagnetic Compatibility (EMC) No. 2014/30/EU

EC Council Directive 2006/42/EC Machinery

RoHS 2011/65/EU

and norms:

EN 60745-1:2009+A11

EN 60745-2-13:2009+A1

EN 55014-1:2006+A1+A2

EN 55014-2:1997/A1+A2

EN 61000-3-2-:2006+A1+A2

EN 61000-3-11:2000

CE label: 16

Place of issuance: Prague Name: Ing. Zdeněk Pech

Chairman of the Board

Date of issuance: 9.3.2016 Signature:

Stránka sa načítava...

Fieldmann FZP 2005-E Používateľská príručka

Fieldmann FZP 2005-E Používateľská príručka

v iných jazykoch