Indesit EWE 71083 W EU Užívateľská príručka

Kategória
Práčky
Typ
Užívateľská príručka
1
GB
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Care and maintenance, 4
Cutting off the water or electricity supply
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Precautions and tips, 5
General safety
Disposal
Description of the washing machine, 6-7
Control panel
Display
Running a wash cycle, 8
Wash cycles and options, 9
Table of wash cycles
Wash options
Detergents and laundry, 10
Detergent dispenser drawer
Preparing the laundry
Fast daily cycles
Special wash cycles
Load balancing system
Troubleshooting, 11
Service, 12
EWE 71083
Instructions for use
WASHING MACHINE
English, 1
GB
УУУУУУУУУУ
NL
CZ
HU
SK
Magyar, 49
Česky,13
Slovensky,25
Nederlands,37
2
GB
! This instruction manual should be kept in a safe
place for future reference. If the washing machine
is sold, transferred or moved, make sure that the
instruction manual remains with the machine so
that the new owner is able to familiarise himself/
herself with its operation and features.
! Read these instructions carefully: they contain
vital information relating to the safe installation
and operation of the appliance.
Unpacking and levelling
Unpacking
1. Remove the washing machine from its packaging.
2. Make sure that the washing machine has not
been damaged during the transportation process.
If it has been damaged, contact the retailer and do
not proceed any further with the installation process.
3. Remove the 4 pro-
tective screws (used
during transportation)
and the rubber washer
with the corresponding
spacer, located on the
rear part of the applian-
ce (see figure).
4. Close off the holes using the plastic plugs
provided.
5. Keep all the parts in a safe place: you will need
them again if the washing machine needs to be
moved to another location.
! Packaging materials should not be used as
toys for children.
Levelling
1. Install the washing machine on a flat sturdy
floor, without resting it up against walls, furniture
cabinets or anything else.
2. If the floor is not per-
fectly level, compensa-
te for any unevenness
by tightening or loo-
sening the adjustable
front feet (see figure);
the angle of inclination,
measured in relation to
the worktop, must not
exceed 2°.
Levelling the machine correctly will provide it with
stability, help to avoid vibrations and excessive
noise and prevent it from shifting while it is ope-
rating. If it is placed on carpet or a rug, adjust the
feet in such a way as to allow a sufficient venti-
lation space underneath the washing machine.
Connecting the electricity and wa-
ter supplies
Connecting the water inlet hose
1. Connect the supply
pipe by screwing it to
a cold water tap using
a ¾ gas threaded con-
nection (see figure).
Before performing the
connection, allow the
water to run freely until
it is perfectly clear.
2. Connect the inlet
hose to the washing
machine by screwing
it onto the correspon-
ding water inlet of the
appliance, which is si-
tuated on the top right-
hand side of the rear
part of the appliance
(see figure).
3. Make sure that the hose is not folded over
or bent.
! The water pressure at the tap must fall within
the values indicated in the Technical details table
(see next page).
! If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.
! Never use second-hand hoses.
! Use the ones supplied with the machine.
Installation
3
GB
65 - 100 cm
Connecting the drain hose
Connect the drain
hose, without bending
it, to a drainage duct or
a wall drain located at a
height between 65 and
100 cm from the floor;
alternatively, rest it on
the side of a washba-
sin or bathtub, faste-
ning the duct supplied
to the tap (see figure).
The free end of the
hose should not be
underwater.
! We advise against the use of hose extensions;
if it is absolutely necessary, the extension must
have the same diameter as the original hose and
must not exceed 150 cm in length.
Electrical connections
Before plugging the appliance into the electricity
socket, make sure that:
•the socket is earthed and complies with all
applicable laws;
•thesocketisabletowithstandthemaximum
power load of the appliance as indicated in the
Technical data table (see opposite);
thepowersupplyvoltagefallswithinthevalues
indicated in the Technical data table (see opposite);
•thesocketiscompatiblewiththeplugofthe
washing machine. If this is not the case, repla-
ce the socket or the plug.
! The washing machine must not be installed
outdoors, even in covered areas. It is extremely
dangerous to leave the appliance exposed to
rain, storms and other weather conditions.
! When the washing machine has been installed,
the electricity socket must be within easy reach.
! Do not use extension cords or multiple sockets.
! The cable should not be bent or compressed.
! The power supply cable must only be replaced
by authorised technicians.
Warning! The company shall not be held responsible
in the event that these regulations are not respected.
The first wash cycle
Once the appliance has been installed, and be-
fore you use it for the first time, run a wash cycle
with detergent and no laundry, using the wash
cycle “Auto Clean” (see “Cleaning the washing
machine”).
Technical data
Model
EWE 71083
Dimensions
width 59.5 cm
height 85 cm
depth 53.5 cm
Capacity
from 1 to 7 kg
Electrical
connections
please refer to the technical
data plate fixed to the machine
Water
connection
maximum pressure
1 MPa (10 bar)
minimum pressure
0.05 MPa (0.5 bar)
drum capacity 52 litres
Spin speed
up to 1000 rotations per minute
Test wash
cycles in
accordance
with re-
gulations
1061/2010
and
1015/2010
Programme 15:
Eco Cotton 60°C.
Programme 15:
Eco Cotton 40°C.
This appliance conforms to
the following EC Directives:
- 2004/108/EC dated
03/05/89 (Electromagnetic
Compatibility)
- 2012/19/EU - WEEE
- 2006/95/EC Low Voltage)
4
GB
Care and maintenance
Cutting off the water and electri-
city supplies
•Turnoffthewatertapaftereverywashcycle.
This will limit wear on the hydraulic system
inside the washing machine and help to pre-
vent leaks.
•Unplugthewashingmachinewhencleaning
it and during all maintenance work.
Cleaning the washing machine
• The outer parts and rubber components of
the appliance can be cleaned using a soft cloth
soaked in lukewarm soapy water. Do not use
solvents or abrasives.
• The washing machine has a “Auto Clean”
programme for its internal parts that must be
run with no load in the drum.
For maximum performance you may want to
use either the detergent (i.e. a quantity 10% the
quantity specified for lightly-soiled garments) or
special additives to clean the washing machine.
We recommend running a cleaning programme
every 40 wash cycles.
To start the programme press buttons A and B
simultaneously for 5 seconds (see figure).
The programme will start automatically and will
last approximately 70 minutes.
Cleaning the detergent dispenser
drawer
Remove the dispenser
by raising it and pulling
it out (see figure).
Wash it under running
water; this operation
should be repeated
frequently.
Caring for the door and drum of
your appliance
•Alwaysleavetheportholedoorajarinorder
to prevent unpleasant odours from forming.
Cleaning the pump
The washing machine is fitted with a self-clea-
ning pump which does not require any mainte-
nance. Sometimes, small items (such as coins
or buttons) may fall into the pre-chamber which
protects the pump, situated in its bottom part.
! Make sure the wash cycle has finished and
unplug the appliance.
To access the pre-chamber:
1. using a screwdri-
ver, remove the cover
panel on the lower
front part of the wa-
shing machine (see
figure);
2. unscrew the lid
by rotating it anti-
clockwise (see figu-
re): a little water may
trickle out. This is
perfectly normal;
3. clean the inside thoroughly;
4. screw the lid back on;
5. reposition the panel, making sure the hooks
are securely in place before you push it onto
the appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If
there are any cracks, it should be replaced
immediately: during the wash cycles, water
pressure is very strong and a cracked hose
could easily split open.
! Never use second-hand hoses.
A
B
5
GB
Precautions and tips
! This washing machine was designed and constructed in
accordance with international safety regulations. The fol-
lowing information is provided for safety reasons and must
therefore be read carefully.
General safety
• Thisappliancewasdesignedfordomesticuseonly.
•Thisappliancecanbeusedbychildrenaged
from 8 years and above and persons with re-
duced physical, sensory or mental capabilities
or lack of experience and knowledge if they
have been given supervision or instruction
concerning use of the appliance in a safe way
and understand the hazards involved. Children
shall not play with the appliance. Cleaning
and user maintenance shall not be made by
children without supervision.
• Donottouchthemachinewhenbarefootorwithwetor
damp hands or feet.
• Donotpullonthepowersupplycablewhenunplugging
the appliance from the electricity socket. Hold the plug and
pull.
• Do not open the detergent dispenser drawer while the
machine is in operation.
• Donottouchthedrainedwaterasitmayreachextremely
high temperatures.
• Neverforcetheportholedoor.Thiscoulddamagethesafety
lock mechanism designed to prevent accidental opening.
• Iftheappliancebreaksdown,donotunderanycircum-
stances access the internal mechanisms in an attempt to
repair it yourself.
• Alwayskeepchildrenwellawayfromtheappliancewhile
it is operating.
• Thedoorcanbecomequitehotduringthewashcycle.
• Iftheappliancehastobemoved,workinagroupoftwo
or three people and handle it with the utmost care. Never
try to do this alone, because the appliance is very heavy.
• Beforeloadinglaundryintothewashingmachine,make
sure the drum is empty.
Disposal
• Disposingofthepackagingmaterials:observelocalregu-
lations so that the packaging may be re-used.
• TheEuropeanDirective2012/19/EU-WEEEonWasteElec-
trical and Electronic Equipment, requires that old household
electrical appliances must not be disposed of in the normal
unsorted municipal waste stream. Old appliances must
be collected separately in order to optimise the recovery
and recycling of the materials they contain and reduce the
impact on human health and the environment.
The crossed out “wheeled bin symbol on the product
reminds you of your obligation, that when you dispose of
the appliance it must be separately collected. Consumers
should contact their local authority or retailer for information
concerning the correct disposal of their old appliance.
6
GB
Detergent dispenser drawer: used to dispense deter-
gents and washing additives (see “Detergents and laundry”).
ON/OFF button : press this briefly to switch the machine
on or off. The START/PAUSE indicator light, which flashes
slowly in a green colour shows that the machine is switched
on. To switch off the washing machine during the wash cycle,
press and hold the button for approximately 2 seconds; if
the button is pressed briefly or accidentally the machine will
not switch off. If the machine is switched off during a wash
cycle, this wash cycle will be cancelled.
WASH CYCLE knob: used to set the desired wash cycle
(see “Table of wash cycles”).
OPTION buttons with indicator light: used to select the
available options. The indicator light corresponding to the
selected option will remain lit.
Button with indicator light KEYPAD LOCK : This option
locks the control panel (except for the ON/OFF button) in
order to prevent both children from changing the washing-
machine settings while in operation and any involuntary
starting. Press it for at least 2 seconds to enable/disable it.
SPIN button : press to reduce or completely exclude the
spin cycle - the value is indicated on the display.
TEMPERATURE button : press to decrease or comple-
tely exclude the temperature: the value will be shown on the
display.
DELAYED START button : press to set a delayed start
time for the selected wash cycle. The delay time will be shown
on the display.
START/PAUSE button with indicator light: when the
green indicator light flashes slowly, press the button to start
a wash cycle. Once the cycle has begun the indicator light
will remain lit in a fixed manner. To pause the wash cycle,
press the button again; the indicator light will flash in an
orange colour. If the symbol is not illuminated, the door
may be opened (wait approximately 3 minutes). To start the
wash cycle from the point at which it was interrupted, press
the button again.
Standby mode
This washing machine, in compliance with new energy saving
regulations, is fitted with an automatic standby system which
is enabled after about 30 minutes if no activity is detected.
Press the ON-OFF button briefly and wait for the machine
to start up again.
Description of the washing
machine
Control panel
TEMPERATURE
Button
Detergent dispenser drawer
OPTION
buttons with
indicator lights
ON/OFF
button
SPIN SPEED
Button
START/PAUSE
button with indicator light
DISPLAY
DELAYED
START Button
WASH CYCLE
knob
Button with indicator light
KEYPAD LOCK
7
GB
Display
The display is useful when programming the machine and provides a great deal of information.
The duration of the available programmes and the remaining time of a running cycle appear in section A; if the DELAY START
option has been set, the countdown to the start of the selected programme will appear. Pressing the relative button, the
machine automatically displays the maximum temperature and spin speed values set for the selected cycle, or the most
recently-used settings if they are compatible with the selected cycle.
The “programme phases” relative to the selected programme and the “programme phase” of the running programme appear
in section B:
Wash
Rinse
Spin
Drain
The icons corresponding to “temperature” , “Programmed start” and “spin” appear in section C from top to bottom:
If the symbol lights up, the display will visualise the set “temperature” value.
When a “delayed start” has been set, the symbol lights up.
If the symbol lights up, the display will visualise the set “spin” value.
Door locked symbol
The lit symbol indicates that the door is locked. To prevent any damage, wait until the symbol turns off before opening the
door.
To open the door while a cycle is in progress, press the START/PAUSE button; if the DOOR LOCKED symbol is switched
off the door may be opened (wait approximately 3 minutes).
B
CA
8
GB
Running a wash cycle
1. SWITCH THE MACHINE ON. Press the button;
the START/PAUSE indicator light will flash slowly in a
green colour.
2. LOAD THE LAUNDRY. Open the porthole door.
Load the laundry, making sure you do not exceed
the maximum load value indicated in the table of
programmes on the following page.
3. MEASURE OUT THE DETERGENT. Pull out the
detergent dispenser drawer and pour the detergent into
the relevant compartments as described in “Detergents
and laundry”.
4. CLOSE THE DOOR.
5. SELECT THE WASH CYCLE. Set the WASH CYCLE
knob to the desired programme; a temperature and spin
speed is set for each wash cycle; these may be adjusted.
The duration of the cycle will appear on the display.
6. CUSTOMISE THE WASH CYCLE. Use the relevant
buttons:
Modifying the temperature and/or spin
speed. The machine automatically displays the
maximum temperature and spin speed values set for
the selected cycle, or the most recently-used settings
if they are compatible with the selected cycle. The
temperature can be decreased by pressing the
button, until the cold wash “OFF” setting is reached.
The spin speed may be progressively reduced by
pressing the button, until it is completely excluded
(the “OFF” setting). If these buttons are pressed again,
the maximum values are restored.
Setting a delayed start.
To set a delayed start for the selected programme,
press the corresponding button repeatedly until the
required delay period has been reached. When this
option is enabled, the symbol lights up on the
display. To remove the delayed start option press the
button until the text “OFF” appears on the display.
Modifying the cycle settings.
• Press the button to enable the option; the indicator
light corresponding to the button will switch on.
• Press the button again to disable the option; the
indicator light will switch off.
! If the selected option is not compatible with the
programmed wash cycle, the indicator light will flash
and the option will not be activated.
! If the selected option is not compatible with another
option which has been selected previously, the indicator
light corresponding to the first option selected will flash
and only the second option will be activated; the indicator
light corresponding to the enabled option will remain lit.
! The options may affect the recommended load value
and/or the duration of the cycle.
7. START THE PROGRAMME. Press the START/
PAUSE button. The corresponding indicator light will
become green, remaining lit in a fixed manner, and the
door will be locked (the DOOR LOCKED symbol will
be on). To change a wash cycle while it is in progress,
pause the washing machine using the START/PAUSE
button (the START/PAUSE indicator light will flash
slowly in an orange colour); then select the desired
cycle and press the START/PAUSE button again.
To open the door while a cycle is in progress, press
the START/PAUSE button; if the DOOR LOCKED
symbol is switched off the door may be opened (wait
approximately 3 minutes). Press the START/PAUSE
button again to restart the wash cycle from the point at
which it was interrupted.
8. THE END OF THE WASH CYCLE. This will be
indicated by the text “END” on the display; when the
DOOR LOCKED symbol switches off the door may be
opened (wait approximately 3 minutes). Open the door,
unload the laundry and switch off the machine.
! If you wish to cancel a cycle which has already begun,
press and hold the button. The cycle will be stopped
and the machine will switch off.
9
GB
Wash cycles and options
Wash options
- If the selected option is not compatible with the
programmed wash cycle, the indicator light will flash and
the option will not be activated.
- If the selected option is not compatible with another
option which has been selected previously, the indicator
light corresponding to the first option selected will flash and
only the second option will be activated; the indicator light
corresponding to the enabled option will remain lit.
Extra Wash
Enable the
Extra Wash
option for very dirty items, where
compatible. Press this option to let the cycle automatically re-
adjust all wash parameters through a longer lasting cycle. The
option always leaves the temperature unchanged, while the spin
cycle is automatically brought back to maximum levels. The user
can set the spin cycle back to the desired value at any time.
Table of wash cycles
Extra Rinse
By selecting this option, the efficiency of the rinse is increased
and optimal detergent removal is guaranteed. It is particularly
useful for sensitive skin.
The option washes cotton and synthetic items,
saving energy and helping the environment. Energy saving
is due to a cold wash cycle, while an enhanced mechanical
action and optimised water use make it possible to reach the
desired result. Recommended for slightly soiled garments.
Use of liquid detergent recommended.
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary according to factors such as
water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.
1) Test wash cycle in compliance with regulations 1061/2010: set wash cycle 15 with a temperature of 60°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments
which can be washed at 60°C. The actual washing temperature may differ from the indicated value.
2) Test wash cycle in compliance with regulations 1061/2010: set wash cycle 15 with a temperature of 40°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments
which can be washed at 40°C. The actual washing temperature may differ from the indicated value.
For all Test Institutes:
2) Long wash cycle for cottons: set wash cycle 15 with a temperature of 40°C.
3) Long programme for synthetics: set programme 4, then select the “
Extra Wash
” option.
* If you select programme 11 and exclude the spin cycle, the machine will drain only.
** The duration of the wash cycle can be checked on the display.
Wash cycles
Description of the wash cycle
Max.
temp.
(°C)
Max.
speed
(rpm)
Detergents
Max.
load (kg)
Residual
dampness %
Energy
consumption
kWh
Total water lt
Cycle
duration
Pre-wash Wash
Fabric
softener
EVERYDAY FAST
1 Colour Mix 59’
40° 1000 -
7 - - - 59’
2 Cotton 59’
60° 1000 -
7 - - - 59’
3 Cotton 45’
40° 1000 -
3,5 - - - 45’
4 Synthetics 59’ (3)
40° 1000 -
3,5 46 0,56 43 59’
5 Mix 30’
30° 800 -
3,5 71 0,16 33 30’
6 Express 20’
20° 800 -
3,5 - - - 20’
Special & Partial
7 Gym Kit
40° 600 -
3,5 - - - **
8 Sport Shoes
30° 600 -
Max.
2 pairs
- - - **
9
Baby: Heavily soiled delicate colours. 40° 800 -
3 - - - **
10 Rinse
- 1000 - -
7 - - - **
11 Spin + Drain
- 1000 - - - 7 - - - **
11 Only Drain *
- OFF - - - 7 - - - **
Dedicated
12
Duvet: for down-stuffed garments. 30° 1000 -
2 - - - **
13
Wool: for wool, cashmere, etc. 40° 800 -
1,5 - - - **
14
Silk/Curtains: for garments in silk and viscose, lingerie.
30° 0 -
1 - - - **
15
Eco Cotton 60° (1): heavily soiled whites and resistant colours. 60° 1000 -
7 62 0,94 52,5 160’
15
Eco Cotton 40° (2): lightly soiled whites and delicate colours. 40° 1000 -
7 62 0,93 85 140’
16
Cotton with prewash: extremely soiled whites. 90° 1000
7 - - - **
10
GB
Detergents and laundry
Detergent dispenser drawer
Good washing results also depend on the correct dose of
detergent: adding too much detergent will not necessarily
result in a more efficient wash, and may in fact cause build
up on the inside of your appliance and contribute to envi-
ronmental pollution.
! Do not use hand washing detergents because these create
too much foam.
! Use powder detergent for white cotton garments, for pre-
washing, and for washing at temperatures over 60°C.
! Follow the instructions given on the detergent packaging.
Open the detergent dispen-
ser drawer and pour in the
detergent or washing additi-
ve, as follows.
compartment 1: Pre-wash detergent (powder)
compartment 2: Detergent for the wash cycle
(powder or liquid)
Liquid detergent should only be poured in immediately
prior to the start of the wash cycle.
compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow the grid.
Note: If a “tablet detergent” is used, always follow the
manufacturer’s instructions.
Preparing the laundry
•Dividethelaundryaccordingto:
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from whites.
•Emptyallgarmentpocketsandcheckthebuttons.
• Donotexceedthevalueslistedinthe“Table of wash
cycles”, which refer to the weight of the laundry when dry.
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1200 g
1 towel 150-250 g
Fast daily cycles
A complete set of fast programmes to wash the most com-
monly used fabrics - even with a full load - and to remove
the most frequent daily dirt in less than 1 hour.
Colour Mix 59’: to wash mixed and coloured items together.
Cotton 59’: cycle designed to wash cotton garments - mainly
white items. It can be used with powder detergent too.
Cotton 45’: short cycle designed to wash delicate cotton items.
Synthetics 59’: specific for synthetic items. If the dirt is
difficult to remove, the temperature can be increased up to
60° and powder detergent can be used too.
Mix 30’: short cycle designed to wash a mixed load of cotton
and synthetic fabrics - white and coloured items together.
Express 20’: this programme refreshes your items, making
them perfumed again in just 20 minutes.
Special wash cycles
Gym Kit: cycle suitable to wash all sports items together,
including gym towels, while respecting their fibres (follow the
instructions in the garment labels).
Sport Shoes: is for washing sports shoes; for best results,
do not wash more than 2 pairs simultaneously.
We recommend fastening any strings before introducing the
shoes into the drum.
Baby: cycle designed for dirt typical of children’s garments
in that it effectively removes any traces of residual detergent.
Duvet: to wash single duvets (the weight of which should not
exceed 2 kg), cushions or clothes padded with goose down
such as puffa jackets, use the special wash cycle number 12.
We recommend that duvets are placed in the drum with their
edges folded inwards (see figure) and that no more than ¾
of the total volume of the drum is used. To achieve the best
results, we recommend that a liquid detergent is used and
placed inside the detergent dispenser drawer.
Wool: all wool garments can be washed using programme
13, even those carrying the “hand-wash only” label. For
best results, use special detergents and do not exceed 1,5 kg
of laundry.
Silk: use special wash cycle 14 to wash all silk garments.
We recommend the use of special detergent which has been
designed to wash delicate clothes.
Curtains: fold curtains and place them in a pillow case or
mesh bag. Use wash cycle 14.
Load balancing system
Before every spin cycle, to avoid excessive vibrations and
to distribute the load in a uniform manner, the drum rotates
continuously at a speed which is slightly greater than the
washing rotation speed. If, after several attempts, the load
is not balanced correctly, the machine spins at a reduced
spin speed. If the load is excessively unbalanced, the
washing machine performs the distribution process instead
of spinning. To encourage improved load distribution and
balance, we recommend small and large garments are
mixed in the load.
1
2
3
11
GB
Troubleshooting
Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure
that the problem cannot be solved easily using the following list.
Problem:
The washing machine does not
switch on.
The wash cycle does not start.
The washing machine does not
take in water (“H2O” will flash on
the display).
The washing machine continuously
takes in and
drains water.
The washing machine does not
drain or spin.
The washing machine vibrates a lot
during the spin cycle.
The washing machine leaks.
The optionindicator lights and the
start/pause” indicator light flash and
an error code appears on the display
(e.g.: F-01, F-..).
There is too much foam.
Possible causes / Solutions:
• Theapplianceisnotpluggedintothesocketfully,orisnotmakingcontact.
• Thereisnopowerinthehouse.
• Thewashingmachinedoorisnotclosedproperly.
• TheON/OFFbuttonhasnotbeenpressed.
• TheSTART/PAUSEbuttonhasnotbeenpressed.
• Thewatertaphasnotbeenopened.
• Adelayedstarthasbeenset..
• Thewaterinlethoseisnotconnectedtothetap.
• Thehoseisbent.
• Thewatertaphasnotbeenopened.
• Thereisnowatersupplyinthehouse.
• Thepressureistoolow.
• TheSTART/PAUSEbuttonhasnotbeenpressed.
• Thedrainhoseisnotfittedataheightbetween65and100cmfromthefloor
(see “Installation”).
• Thefreeendofthehoseisunderwater(see “Installation”).
• Thewalldrainagesystemisnotfittedwithabreatherpipe.
If the problem persists even after these checks, turn off the water tap, switch
the appliance off and contact the Assistance Service. If the dwelling is on one of
the upper floors of a building, there may be problems relating to water drainage,
causing the washing machine to fill with water and drain continuously. Special
anti-draining valves are available in shops and help to avoid this inconvenience.
• Thewashcycledoesnotincludedraining:somewashcyclesrequirethedrain
phase to be started manually.
• Thedrainhoseisbent(see “Installation”).
• Thedrainageductisclogged.
• Thedrumwasnotunlockedcorrectlyduringinstallation(see “Installation”).
• Thewashingmachineisnotlevel(see “Installation”).
• Thewashingmachineistrappedbetweencabinetsandwalls(see “Installation”).
• Thewaterinlethoseisnotscrewedonproperly(see “Installation”).
• Thedetergentdispenserdrawerisblocked(forcleaninginstructions,see “Care
and maintenance”).
• Thedrainhoseisnotfixedproperly(see “Installation”).
• Switchoffthemachineandunplugit,waitforapproximately1minuteandthen
switch it back on again.
If the problem persists, contact the Technical Assistance Service.
• Thedetergentisnotsuitableformachinewashing(itshoulddisplaythetext
“for washing machines” or “hand and machine wash”, or the like).
• Toomuchdetergentwasused.
12
GB
Service
Before calling for Assistance:
• Check whether you can solve the problem alone (see “Troubleshooting”);
• Restarttheprogrammetocheckwhethertheproblemhasbeensolved;
• Ifthisisnotthecase,contactanauthorisedTechnicalAssistanceCentreusingthetelephonenumberprovidedonthe
guarantee certificate.
! Always request the assistance of authorised technicians.
Have the following information to hand:
• thetypeofproblem;
• theappliancemodel(Mod.);
• theserialnumber(S/N).
This information can be found on the data plate applied to the rear of the washing machine, and can also be found on the
front of the appliance by opening the door.
CZ
13
Český,13
Obsah
Instalace, 14-15
Rozbalení a vyrovnání do vodorovné polohy
Připojení k elektrické a k vodovodní síti
První prací cyklus
Technické údaje
Údržba a péče, 16
Uzavření přívodu vody a vypnutí elektrického napájení
Čištění pračky
Čištění dávkovače pracích prostředků
Péče o dvířka a buben
Čištění čerpadla
Kontrola přítokové hadice na vodu
Opatření a rady, 17
Základní bezpečnostní pokyny
Likvidace
Popis pračky, 18-19
Ovládací panel
Displej
Jak provést prací cyklus, 20
Programy a funkce, 21
Tabulka programů
Funkce praní
Prací prostředky a prádlo, 22
Dávkovač pracích prostředků
Příprava prádla
Každodenní rychlé cykly
Speciální programy
Systém automatického vyvážení náplně
Poruchy a způsob jejich odstranění, 23
Servisní služba, 24
CZ
EWE 71083
Návod k použití
PRAČKA
14
CZ
! Je důležité uschovat tento návod tak, aby-
ste jej mohli kdykoli konzultovat. V případě
prodeje, darování nebo přestěhování pračky
se ujistěte, že zůstane uložen v blízkosti
pračky, aby mohl posloužit novému majiteli
při seznámení s její činností a s příslušnými
upozorněními.
! Pozorně si přečtěte uvedepokyny: ob-
sahuležiinformace týka se instalace,
poití a bezpečnosti při práci.
Rozbalení a vyrovnání do vodoro-
vné polohy
Rozbalení
1. Rozbalte pračku.
2. Zkontrolujte, zda během přepravy
nedošlo k jejímu poškození. V případě, že
je poškozena, ji nezapojujte a obraťte se na
prodejce.
3. Odstraňte 4
šrouby chránící
před poškozením
během přepravy a
gumovou podložku
s příslušnou
rozpěrkou, které se
nacházejí v zadní
části (viz obrázek).
4. Uzavřete otvory po šroubech plastovými
krytkami z příslušenství.
5. Uschovejte všechny díly: v případě
opětovné přepravy pračky je bude třeba na-
montovat zpět.
! Obaly nejsou hračky pro děti!
Vyrovnání do vodorovné polohy
1. Pračku je třeba umístit na rovnou a pe-
vnou podlahu, aniž by se opírala o stěnu,
nábytek či něco jiného.
2. V případě, že
podlaha není do-
konale vodorovná,
mohou být případné
rozdíly vykompenzo-
vány šroubováním
předních nožek (viz
obrázek); Úhel sk-
lonu, naměřený na
pracovní ploše, ne-
smí přesáhnout 2°.
Dokonalé vyrovnání do vodorovné polohy
zabezpečí stabilitu zařízení a zamezí vzniku
vibrací a hluku během činnosti. V případě
instalace na podlahovou krytinu nebo na
koberec nastavte nožky tak, aby pod pračkou
zůstal dostatečný volný prostor pro ventilaci.
Připojení k elektrické a k vodovodní
síti
Připojení přítokové hadice vody
1. Připojte přívodní
h a d i c i j e j í m
zašroubováním ke ko-
houtku studené vody
s hrdlem se závitem
3/4“ (viz obrázek).
Před připojením ha-
dice nechte vodu
odtékat, dokud nebu-
de čirá.
2. Připojte přítokovou
hadici k pračce
prostřednictvím
příslušné přípojky
na vodu, umístěné
vpravo nahoře (viz
obrázek).
3. Dbejte na to, aby hadice nebyla příliš oh-
nutá ani stlačená.
! Tlak v rozvodu vody se musí pohybovat
v rozmezí hodnot uvedených v tabulce s
technickými údaji
(viz vedlejší strana).
! V případě, že délka přítokové hadice ne-
bude dostatečná, obraťte se na specializo-
vanou prodejnu nebo na autorizovaný tech-
nický personál.
! Nikdy nepoužívejte již použité hadice.
! Používejte hadice z příslušenství zařízení.
Instalace
CZ
15
Připojení vypouštěcí hadice
Připojte vypouštěcí
hadici, aniž byste ji
ohýbali, k odpado-
vému potrubí nebo
k odpadu ve stěně,
který se nachází od
65 do 100 cm nad
zemí;
nebo ji uchyťte k
okraji umývadla či
vany a připevněte
vodicí držák
z příslušenství ke
kohoutu (viz obrá-
zek). Volný konec
vypouštěcí hadi-
ce nesmí zůstat
ponořený do vody.
! Použití prodlužovacích hadic se
nedoporučuje; je-li však nezbytné,
prodlužovací hadice musí mít stejný průměr
jako originální hadice a její délka nesmí
přesáhnout 150 cm.
Připojení k elektrické síti
Před zasunutím zástrčky do zásuvky se
ujistěte, že:
Je zásuvka uzemněna a že vyhovuje nor-
mám;
je zásuvka schopna snést maximální zátěž
odpovídající jmenovitému příkonu zařízení,
uvedenému v tabulce s technickými údaji
(viz vedle);
hodnota napájecího napětí odpovídá
údajům uvedeným v tabulce s technickými
údaji (viz vedle);
je zásuvka kompatibilní se zástrčkou
pračky. V opačném případě je třeba
vyměnit zásuvku nebo zástrčku.
! Pračka nesmí být umístěna venku – pod
širým nebem, a to ani v případě, že by se
jednalo o místo chráněné před nepřízní
počasí, protože je velmi nebezpečné vystavit
ji působení deště a bouří.
! Po denitivní instalaci pračky musí zásuvka
zůstat snadno přístupná.
! Nepoužívejte prodlužova kabely a rozvodky.
! Kabel nesmí být ohnutý ani stlačený.
! Výměna kabelu musí být svěřena výhradně
autorizovanému technickému personálu.
Upozornění! Výrobce neponese žádnou
odpovědnost za následky nerespektování
uvedených předpisů.
První prací cyklus
Po instalaci zařízení je třeba ješ edtím,
než je použijete na praní prádla, provést jeden
zkušebcyklus s pracím prostředkem a bez
náplně prádla nastavením pracího programu
„Samočištění(viz “Čištění pračky”).
65 - 100 cm
Technické údaje
Model EWE 71083
Rozměry
šířka 59,5 cm
výška 85 cm
hloubka 53,5 cm
Kapacita od 1 do 7 kg
Napájení
Viz štítek s technickými úda-
ji, aplikovaný na zařízení.
Připojení k
rozvodu vody
maximální tlak
1 MPa (10 bar)
minimální tlak
0.05 MPa (0.5 bar)
kapacita bubnu 52 litrů
Rychlost
odstřeďování
do 1000 otáček za minutu
Kontrolní
programy po-
dle předpisy
1061/2010 a
1015/2010
program 15; Eco bavlnu 60°C.
program 15; Eco bavlnu 40°C.
Toto zařízení odpovídá ná-
sledujícím normám Evrop-
ské unie:
- 2004/108/CE (Elektroma-
gnetická kompatibilita)
- 2006/95/CE (Nízké napětí)
- 2012/19/EU - WEEE
16
CZ
Uzavření přívodu vody a vypnutí
elektrického napájení
Po každém praní uzavřete přívod vody.
Tímto způsobem dochází k omezení
opotřebení pračky a ke snížení nebezpečí
úniku vody.
ed zahájením čištění pračky a během ope-
rací údržby vytáhněte zástrčku napájecího
kabelu z elektrické zásuvky.
Čištění pračky
Vnější části a části z gumy se mohou čistit
hadrem navlhčeným ve vlažvodě a sa-
ponátu. Nepoužívejte rozpouštědla ani
abrazivní látky.
Pračka je vybavena programem Samočištění
vniních částí, který musí být proveden bez ja-
kéhokoli druhu náplně v bubnu.
Prací prostředek (množství rovnající se
10% množství doporučeného pro částeč
znečištěné prádlo) nebo specické přídavné
prostředky pro čištění pračky budou moci být
poity jako pomocné prosedky v pracím
programu. Doporučuje se provést samočisticí
program každých 40 cyklů praní.
Pro aktivaci programu stiskněte součas
tlačítka A a B na dobu 5 sekund (viz obrázek).
Program bude zahájen automaticky a bude trvat
přibližně 70 minut.
Čtě dávkovače prach prostředků
Vytáhněte dávkovač
jeho nadzvednutím
a vytažením směrem
ven (viz obrázek).
Umyjte jej pod prou-
dem vody; tento druh
vyčištění je třeba
provádět pravidelně.
Údržba a péče
Péče o dvířka a buben
Dvířka ponechte pokaždé pootevřená, aby
se zabránilo tvorbě nepříjemných zápachů.
Čištění čerpadla
Součáspračky je samočisticí čerpadlo, které
nevyžaduje údržbu.že se však stát, že se
v jeho vstupčásti, určené k jeho ochraně
a nacházející se v jeho spodní části, zachytí
drobnéedměty (mince, knoíky).
! Ujistěte se, že byl prací cyklus ukončen, a
vytáhněte zástrčku ze zásuvky.
Přístup ke vstupní části čerpadla:
1. pomo-
cí šroubováku
odstraňte krycí pa-
nel nacházející se v
přední části pračky
(viz obrázek);
2. Odšroubujte víko
jeho otáčením proti
směru hodinových
ručiček (viz obrázek):
vytečení malého
množství vody je
zcela běžným jevem;
3. dokonale vyčistěte vnitřek;
4. zašroubujte zpět víko;
5. namontujte zpět panel, přičemž se před
jeho přisunutím k zařízení ujistěte, že
došlo ke správnému zachycení háčků do
příslušných podélných otvorů.
Kontrola přítokové hadice na vodu
Stav přítokové hadice je třeba zkontrolovat
alespoň jednou ročně. Jsou-li na ní viditel-
né praskliny nebo trhliny, je třeba ji vyměnit:
silný tlak působící na hadici během pracího
cyklu by mohl způsobit její náhlé roztržení.
! Nikdy nepoužívejte již použité hadice.
A
B
CZ
17
Opatření a rady
! Pračka byla navržena a vyrobena v souladu s platnými
mezinárodními bezpečnostním předpisy. Tato upozornění
jsou uváděna z bezpečnostních důvodů a je třeba si je
pozorně přečíst.
Základní bezpečnostní pokyny
• Toto zízení bylo naveno hradně pro použití v
domácnosti.
Toto zařízení mohou používat děti od 8 let a
osoby se sníženými fyzickými, senzorickými
nebo duševními schopnostmi nebo osoby s
nedostatečnými zkušenostmi a znalostmi,
když se nacházejí pod náležitým dohledem
nebo když byly náležitě vyškoleny ohledně
bezpečného použi zařízení a udomují
si související nebezpečí. Děti si nesmí hrát
se zařízením. Děti nesmí provádět operace
údržby a čištění bez dohledu.
• Pračku mohou používat pouze dospělé osoby podle
pokynů uvedených v tomto návodu.
• Nedotýkejte se zařízení bosí nebo v případě, že máte
mokré ruce či nohy.
• Nevytahujte zástrčku ze zásuvky tahem za kabel, ale
uchopením za zástrčku.
• Neotvírejte dávkovač pracích prostředků během činnosti
zařízení.
• Nedotýkejte se odčerpávané vody, protože že mít
velmi vysokou teplotu.
• Nepokoušejte se o násilné otevředvířek: mohlo by dojít
k poškození bezpečnostního uzávěru, který zabraňuje
náhodnému otevření.
• Při výskytu poruchy se v žádném případě nepokoušejte
o opravu vnitřních částí zařízení.
• Vždy mějte pod kontrolou děti a zabraňte tomu, aby se
přibližovaly k zařízení během pracího cyklu.
• Během pracího cyklu mají dvířka tendenci ohřát se.
• V případě potřeby přemísťujte pračku ve dvou nebo ve
třech a věnujte celé operaci maximální pozornost. Nikdy
se nepokoušejte zařízení přemísťovat sami, je totiž velmi
těžké.
• Před zahájením vkládání prádla zkontrolujte, zda je bu-
ben prázdný.
Likvidace
• Likvidace obalových materiálů: při jejich odstranění postu-
pujte v souladu s místním předpisy a dbejte na možnou
recyklaci.
• Evropská směrnice 2012/19/EU - WEEE o odpadních
elektrických a elektronických zařízeních stanovuje, že
staré domácí elektrické spotřebiče nesmí být odkládány
do běžného netříného domovho odpadu. Sta
spotřebiče musí být odevzdány do odděleného sběru, a
to za účelem recyklace a optimálního využití materiálů,
které obsahují, a z důvodu předcházení negativm
dopadům na lidské zdraví a životní prostředí.
Symbol přeškrtnuté popelnice na výrobku vás
upozorňuje na povinnost odevzdat zařízení po skončení
jeho životnosti do odděleného sběru.
Spotřebitelé by měli kontaktovat příslušné místní úřady
nebo svého prodejce ohledně informací týkajících se
správné likvidace starého zařízení.
18
CZ
Dávkovpracích prostředků: slouží k dávkovápracích
prostředků a přídavných prostředků (viz „Prací prostředky
a prádlo“).
Tlačítko ON/OFF : zapněte nebo vypněte pračku
krátkým stisknutím tlítka. Kontrolka START/PAUSE
pomalu blikající zeleným světlem poukazuje na to, že je
stroj zapnutý. Za účelem vypnutí pračky během praní je
třeba držet tlačítko stisknuté déle, přibližně 2 sek.; krátké
nebo náhodné stisknutí neumožní vypnutí pračky. Vypnutí
zařízeběhem praní způsozrušení probíhajícího pracího
programu.
Otočný ovladač PROGRAMŮ: slouží k nastavení
požadovaného programu (viz “Tabulka pracích programů”).
FUNKČNÍ tlačítka s kontrolkami: slouží k volbě jednotli-
vých dostupných funkcí. Kontrolka zvolené funkce zůstane
rozsvícena.
ZABLOKOVÁTLAČÍTEK : Tato možnost zablokuje
ovládací panel (s výjimkou tlačítka ZAPNOUT/VYPNOUT)
a slouží k tomu, aby ti nemohly prot změny v
nastavení pračky během její činnosti a aby se zabránilo
náhodné aktivaci. Aktivuje a ruší se stisknutím tlačítka na
dobu nejméně 2 sekund.
Tlačítko ODSTŘEĎOVÁNÍ : stiskněte za účelem snížení
nebo úplného vyloučení odstřeďování - hodnota bude
uvedena na displeji.
Tlačítko TEPLOTY : Stiskněte za účelem snížení nebo
úplného vyloení teploty; hodnota bude uvedena na
displeji.
Tlačítko ODLOŽENÉHO STARTU : stiskněte za účelem
nastavení odloženého startu zvoleného programu. Doba,
o kterou bude start odložen, bude zobrazena na displeji.
Tlačítko s kontrolkou START/PAUSE: když zelená kontrolka
začne pomalu blikat, stiskněte toto tlačítko pro zahájení
pra. Po zajení cyklu se kontrolka rozsví sm
světlem. ejete-li si erušit praní, opětov stiskněte
tlačítko; kontrolka bude blikat oranžovým světlem. Když
symbol není rozsvícen, je možné otevřít dvířka (vyčkejte
přibližně 3 minuty). Za účelem opětovného zahájení cyklu
z místa, v němž byl přerušen, opětovně stiskněte tlačítko.
Pohotovostní režim
Za účelem shody s novými předpisy souvisejícími s ener-
getickou úsporou je tato pračka vybavena systémem au-
tomatického vypnutí (přechodu do pohotovostního režimu
standby), který je aktivován po uplynutí přibližně 30 minut,
když se pračka nepoužívá. Krátce stiskněte tlačítko ON/
OFF a vyčkejte na obnovení činnosti zařízení.
Popis pračky
Tlačítko s kontrolkou
START/PAUSE
Ovládací panel
Tlačítko
TEPLOTY
Tlačítko
ODSTŘEĎOVÁNÍ
Displej
Tlačítko
ON/OFF
Dávkovač pracích
prostředků
Tlačítko
ODLOŽENÉHO
STARTU
FUNKČNÍ
tlačítka s
kontrolkami
Otočný ovladač
PROGRAMŮ
Tlačítko s kontrolkou
ZABLOKOVÁNÍ
TLAČÍTEK
CZ
19
Displej
Displej slouží k naprogramování zařízení a poskytuje četné informace.
V části A je zobrazována doba trvání různých programů, které jsou k dispozici, a po zahájení cyklu i zbývající doby do
jeho ukončení; v případě nastavení ODLOŽENÉHO STARTU bude zobrazena doba chybějící do zahájení zvoleného
programu. Kromě toho budou při stisknutí příslušného tlačítka zobrazeny maximální hodnoty „odstřeďování“ a „teploty“,
kterých stroj může dosáhnout v závislosti na nastaveném programu.
V části B jsou zobrazovány „fáze praní“, které jsou součástí zvoleného cyklu, a po zahájení programu také probíhající
„fáze praní“:
Praní
Máchání
Odstřeďování
Odčerpání vody
V části C se nacházejí, v pořadí shora dolů, ikony týkající se „teploty“ , „Odloženého startu“ a „odstřeďování“ :
Rozsvícený symbol poukazuje na to, že na displeji je zobrazena hodnota nastavené „teploty“.
Rozsvícený symbol poukazuje na to, že byl nastaven „Odloženého startu“.
Rozsvícený symbol poukazuje na to, že na displeji je zobrazena hodnota nastaveného „odstřeďování“.
Symbol Zablokovaných dvířek
Rozsvícený symbol poukazuje na zajištení dvírek. Aby se predešlo poškození, pred otevrením dvírek je treba vyckat na
zhasnutí uvedeného symbolu (vyčkejte přibližně 3 minuty).
Za účelem otevření dvířek v průběhu pracího cyklu stiskněte tlačítko START/PAUSE; když bude symbol ZABLOKO-
VANÝCH DVÍŘEK zhasnutý, bude možné otevřít dvířka (vyčkejte přibližně 3 minuty).
CA
B
20
CZ
Jak provést prací cyklus
1. ZAPNUTÍ ZAŘÍZENÍ. Stiskněte tlačítko ; kontrolka
START/PAUSE bude pomalu blikat zelenou barvou.
2. NAPLŇTE PRAČKU PRÁDLEM. Otevřete dvířka.
Naplňte pračku prádlem a dbejte přitom, aby nedošlo
k překročení množství náplně, uvedeného v tabulce
programů na následující straně.
3. DÁVKOVÁNÍ PRACÍHO PROSTŘEDKU. Vytáhněte
dávkovač pracích prostředků a naplňte prací
prostředek do příslušných přihrádek způsobem
vysvětleným v části „Prací prostředky a prádlo“.
4. ZAVŘETE DVÍŘKA.
5. ZVOLTE PRACÍ PROGRAM. Otočným ovladačem
PROGRAMŮ nastavte požadovaný prací program;
ke zvolenému programu je přiřazena teplota a rychlost
odstřeďování, které se dají měnit. Na displeji bude
zobrazena doba trvání cyklu.
6. PROVEĎTE UŽIVATELSKÁ NASTAVENÍ PRACÍHO
CYKLU. Poijte íslušná tlačítka:
Změňte teplotu a/nebo odstřeďování. Zařízení
automaticky zvolí teplotu a maximální rychlost
odstřeďování přednastavené pro zvolený program;
tyto hodnoty se nesmí zvyšovat. Stisknutím tlačítka
je možné postupně snížit teplotu až po praní ve
studené vodě „OFF“. Stisknutím tlačítka je možné
postupně snížit rychlost odstřeďování až po jeho
úplné vyloučení „OFF“. Další stisknutí tlačítek obnoví
nastavení maximálních přednastavených hodnot.
Nastavte odložený start.
Pro nastavení odloženého startu zvoleného
programu stiskněte příslušné tlačítko až do dosažení
požadované doby odložení. Po zvolení této volitelné
funkce se zobrazí symbol . Zrušení odloženého
startu se provádí stisknutím tlačítka až do zobrazení
nápisu OFF.
Změňte vlastnosti cyklu.
Stiskněte tlačítka aktivace funkce; dojde k
rozsvícení odpovídající kontrolky tlačítka.
Opětovným stisknutím můžete zvolenou funkci
zrušit; příslušná kontrola zhasne.
! V případě, že zvolená funkce není kompatibilní
s nastaveným pracím programem, příslušná kontrolka
začne blikat a funkce nebude aktivována.
! V případě, že zvolená funkce není kompatibilní
s jinou předem zvolenou funkcí, kontrolka první funkce
bude blikat a bude aktivována pouze druhá, přičemž
kontrolka zvolené funkce se rozsvítí stálým světlem.
! Funkce mohou změnit doporučenou náplň a/nebo
dobu trvání cyklu.
7. SPUSŤTE PROGRAM. Stiskte tlačítko START/
PAUSE.íslušná kontrolka se rozsvítí stálým zelem
světlem a dojde k zablokování dvířek (rozsvíce symbol
ZABLOKOVANÝCH DŘEK ). Za účelem změny
programu hem probíhaho cyklu erte činnost
prky stiknum tlačítka START/PAUSE (kontrolka
START/PAUSE bude pomalu blikat oraovým světlem);
zvolte požadova cyklus a otov stiskte tlítko
START/PAUSE.
Za účelem oteení dřek v průběhu praho cyklu
stiskněte tlačítko START/PAUSE; kd bude symbol
ZABLOKOVANÝCH DŘEK zhasnutý, bude m
otevřít dřka (vkejte přibližně 3 minuty). Opětovm
stisknutím tlítka START/PAUSE znovu uveďte do
činnosti prací program z bodu, ve ktem byl přerušen.
8. UKONČENÍ PROGRAMU. Bude oznámeno
zobrazením nápisu „END“ na displeji. Po zhasnutí
symbolu ZABLOKOVANÝCH DVÍŘEK bude možné
otevřít dvířka (vyčkejte přibližně 3 minuty). Otevřete
dvířka, vyložte prádlo a vypněte zařízení.
! Přejete-li si zrušit již zahájený cyklus, znovu dlouze
stiskněte tlačítko . Cyklus bude přerušen a dojde k
automatickému vypnutí zařízení.
1 / 1

Indesit EWE 71083 W EU Užívateľská príručka

Kategória
Práčky
Typ
Užívateľská príručka