Hoover HI642MCBB Používateľská príručka

Instruction Manual For Induction Hob

ENGLISH

Návod k obsluze indukční varné desky

ČEŠTINA

Bedienungsanleitung für Induktionskochfeld

DEUTSCH

Manuale di istruzioni per il piano cottura a induzione

ITALIANO

Manual de instruções para placa de indução

PORTUGUÊS

Návod na obsluhu pre indukčnú varnú dosku

SLOVENČINA

MODEL: HI642MCBB

MODEL: HTP644MCBB

THANK YOU FOR PURCHASING THE HOOVER INDUCTION HOB. PLEASE READ THIS

INSTRUCTION MANUAL CAREFULLY BEFORE USING THE HOB KEEP IT IN A SAFE PLACE

FOR FUTURE REFERENCE.

1

Download hOn App

In the hOn App you’ll have access to several recipes and

extra contents

2

SAFETY WARNINGS

PLEASE READ THE FOLLOWING INSTRUCTIONS

CAREFULLY BEFORE USING THE APPLIANCE.

Installation

Electrical Shock Hazard

•Disconnect the appliance from the mains electricity supply

before carrying out any work or maintenance on it.

•Connection to a good earth wiring system is essential and

mandatory.

•Means for disconnection must be incorporated in the fixed

wiring in accordance with the wiring rules.

•Alterations to the domestic wiring system must only be

made by a qualified electrician.

•Failure to follow this advice may result in electrical shock

or death.

Cut Hazard

•Take care - panel edges are sharp.

•Failure to use caution could result in injury or cuts.

Important safety instructions

•Read these instructions carefully before installing or using

this appliance.

•No combustible material or products should be placed on

this appliance at any time.

•Please make this information available to the person

responsible for installing the appliance as it could reduce

your installation costs.

•In order to avoid a hazard, this appliance must be installed

according to these instructions for installation.

3

•This appliance is to be properly installed and earthed only

by a suitably qualified person.

•This appliance should be connected to a circuit which

incorporates an isolating switch providing full

disconnection from the power supply.

•WARNING: Use only hob guards designed by the

manufacturer of the cooking appliance or indicated by the

manufacturer of the appliance in the instructions for use as

suitable or hob guards incorporated in the appliance. The

use of inappropriate guards can cause accidents.

•Failure to install the appliance correctly could invalidate

any warranty or liability claims.

•Regarding the details of installation, thanks to refer to the

section <Installation>.

Operation and maintenance

Electrical Shock Hazard

•Do not cook on a broken or cracked cooktop. If the cooktop

surface is break or crack, switch the appliance off

immediately at the mains power supply (wall switch) and

contact a qualified technician.

•Switch the cooktop off at the wall before cleaning or

maintenance.

•Failure to follow this advice may result in electrical shock

or death.

Health Hazard

•This appliance complies with electromagnetic safety

standards.

Hot Surface Hazard

4

•During use, accessible parts of this appliance will become

hot enough to cause burns.

•Do not let your body, clothing or any item other than

suitable cookware contact the ceramic glass until the

surface is cool.

•Metallic objects such as knives, forks, spoons and lids

should not be placed on the hob surface since they can get

hot

•Children less than 8 years of age shall be kept away unless

continuously supervised.

•Handles of saucepans may be hot to touch. Check saucepan

handles do not overhang other cooking zones that are on.

Keep handles out of reach of children.

•Failure to follow this advice could result in burns and

scalds.

Cut Hazard

•The razor-sharp blade of a cooktop scraper is exposed when

the safety cover is retracted. Use with extreme care and

always store safely and out of reach of children.

•Failure to use caution could result in injury or cuts.

Important safety instructions

•Never leave the appliance unattended when in use.

Boil-over causes smoking and greasy spillovers that may

ignite.

•Never use your appliance as a work or storage surface.

•Never leave any objects or utensils on the appliance.

•Never use your appliance for warming or heating the room.

•After use, always turn off the cooking zones and the

cooktop as described in this manual (i.e. by using the touch

controls). Do not rely on the pan detection feature to turn

off the cooking zones when You remove the pan.

5

•Do not allow children to play with the appliance or sit,

stand, or climb on it.

•Do not store items of interest to children in cabinets above

the appliance. Children climbing on the cooktop could be

seriously injured.

•Do not leave children alone or unattended in the area where

the appliance is in use.

•Children or persons with a disability which limits their

ability to use the appliance should have a responsible and

competent person to instruct them in its use. The instructor

should be satisfied that they can use the appliance without

danger to themselves or their surroundings.

•Do not repair or replace any part of the appliance unless

specifically recommended in the manual. All other

servicing should be done by a qualified technician.

•Do not use a steam cleaner to clean your cooktop.

•Do not place or drop heavy objects on your cooktop.

•Do not stand on your cooktop.

•Do not use pans with jagged edges or drag pans across the

glass surface as this can scratch the glass.

•Do not use scourers or any other harsh abrasive cleaning

agents to clean your cooktop, as these can scratch the

ceramic glass.

•If the supply cord is damaged, it must be replaced by the

manufacturer, its service agent or similarly qualified

persons in order to avoid a hazard.

•This appliance is intended to be used in a domestic

household environment only! Commercial use of any kind

is not covered under the manufacturer's warranty!

6

•WARNING: The appliance and its accessible parts become

hot during use. Young children should be kept away.

•Care should be taken to avoid touching heating elements.

•Children less than 8 years of age shall be kept away unless

continuously supervised.

•This appliance can be used by children aged from 8 years

and above and persons with reduced physical, sensory or

mental capabilities or lack of experience and knowledge if

they have been given supervision or instruction concerning

use of the appliance in a safe way and understand the

hazards involved.

•Children shall not play with the appliance. Cleaning and

user maintenance shall not be made by children without

supervision.

•WARNING: Unattended cooking on a hob with fat or oil

can be dangerous and may result in fire. NEVER try to

extinguish a fire with water, but switch off the appliance

and then cover flame e.g. with a lid or a fire blanket.

•WARNING: Danger of fire: do not store items on the

cooking surfaces.

•WARNING: If the surface is cracked, switch off the

appliance to avoid the possibility of electric shock, for hob

surfaces of glass-ceramic or similar material which protect

live parts.

•A steam cleaner is not to be used.

•The appliance is not intended to be operated by means of an

external timer or separate remote-control system.

•CAUTION: The cooking process has to be supervised. A

short term cooking process has to be supervised

7

continuously.

•Power cord can’t accessible after installation.

Product Overview

Top View

HI642MCBB

HTP644MCBB

1. 2300 W zone, boost to 3000 W

2. 1200 W zone, boost to 1500 W

3. 1800 W zone, boost to 2100 W

4. 1200 W zone, boost to 1500 W

5. Control panel

1. 1800 W zone, boost to 2100 W

2. 1800 W zone, boost to 2100 W

3. 1800 W zone, boost to 2100 W

4. 1200 W zone, boost to 1500 W

5. 3000 W zone, boost to 3600 W

6. Control panel

8

The Control Panel

HI642MCBB

HTP644MCBB

Product Information

The ceramic/induction hob can meet different kinds of cuisine demands because of

resistance wire heating, micro-computerized control and multi-power selection, really

the optimal choice for modern families.

The hob centers on customers and adopts personalized design. The hob has safe and

reliable performances, making your life comfortable and enabling to fully enjoy the

pleasure from life.

1. ON/OFF control 6. Boost control

2. Heating zone selection controls 7. Pause control

& Power regulating key 8. Keep warm

3. Timer regulating control 9. Automatic pan detection

4. Keylock control 10. Flexible zone

5. Energy efficiency

9

A Word on Induction Cooking

Induction cooking is a safe, advanced, efficient, and economical cooking technology. It

works by electromagnetic vibrations generating heat directly in the pan, rather than

indirectly through heating the glass surface. The glass becomes hot only because the

pan eventually warms it up.

Before using your New Hob

•Read this guide, taking special note of the ‘Safety Warnings’ section.

•Remove any protective film that may still be on your induction hob.

Using the Touch Controls

•The controls respond to touch, so you don’t need to apply any pressure.

•Use the ball of your finger, not its tip.

•You will hear a beep each time a touch is registered.

•Make sure the controls are always clean, dry, and that there is no object (e.g. a

utensil or a cloth) covering them. Even a thin film of water may make the

controls difficult to operate.

iron pot

magnetic circuit

ceramic glass plate

induction coil

induced currents

10

Choosing the right Cookware

•Only use cookware with a base suitable for induction cooking. Look for the

induction symbol on the packaging or on the bottom of the pan.

•You can check whether your cookware is suitable by carrying out a magnet

test. Move a magnet towards the base of the pan. If it is attracted, the pan is

suitable for induction.

•If you do not have a magnet:

1. Put some water in the pan you want to check.

2. Follow the steps under ‘To start cooking’.

3. If does not flash in the display and the water is

heating, the pan is suitable.

•Cookware made by the following materials is not

suitable: pure stainless steel, aluminum or copper

without a magnetic base, glass, wood, porcelain, ceramic,

and earthenware.

Size of burner (mm)

The minimum cookware (diameter /mm)

160

120

180

140

210

180

Flexible zone

250

Do not use cookware with jagged edges or a curved base.

Make sure that the base of your pan is smooth, sits flat against the glass, and is the same

size as the cooking zone. Always centre your pan on the cooking zone.

Always lift pans off the ceramic hob – do not slide, or they may scratch the glass.

11

Use pans whose diameter of the ferromagnetic area (base of the pan) is in the

range of dimensions in the table below. (Table 1)

- If you use smaller pots, performance could be affected

- If you use pot with a diameter smaller than the one indicated in the table

above, pots may not be detected

According to the dimension of the zone you can use pots of different diameters

as picture below:

If the ferromagnetic part covers only partially the base of the pan, only the

ferromagnetic area will heat up, the rest of the base may not heat up a

sufficient temperature for cooking.



If the ferromagnetic area is not homogeneous, but presents others material

such as aluminum this may affect the heating up and the pan detection.



If the base of the pan is similar to the pictures below the pan could be not

detected.

12

Using your Induction Hob

To start cooking

•After power on, the buzzer beeps once, all the indicators light up for 1 second then

go out, indicating that the hob has entered the state of standby mode.

1. Touch the ON/OFF switch. all the indicators show “– “

2. Place a suitable pan on the cooking zone that you wish to use.

Make sure the bottom of the pan and the surface of the

cooking zone is clean and dry.

3. Select a heat setting by touching the “slider” control.

•If you don’t choose a heat setting within 1 minute,

the Induction hob will automatically switch off.

You will need to start again at step 1.

•You can modify the heat setting at any time during

cooking.

When you have finished cooking

1. Turn the cooking zone off by touching “slider”control

down to“0”. Make sure the display shows“0”.

2. Turn the whole hob off by touching the ON/OFF

control.

3. Beware of hot surfaces

“H” will show which means cooking zone is too hot to touch. It

will disappear when the surface has cooled down to a safe

temperature. It can also be used as an energy saving function if

you want to heat further pans, use the hotplate that is still hot.

13

Using the Power Management

It is possible to set a maximum power absorption level for the induction hob, choosing

up to different power ranges.

Induction hobs are able to limit themselves automatically in order to work at lower

power level, to avoid the risk of overloading.

To enter the power management function

1. Turn on the hob, then press at the same time the “+”(timer) and Pause. The time

indicator will show “P5” which means power level 5. The default mode is on 7.2Kw.

To switch to another level

Press +/- from the timer. There are 5 power levels, from “P1” to “P5”. The timer

indicator will show one of them.

“P1”: the maximum power is 2.5 Kw.

“P2”: the maximum power is 3.5 Kw.

“P3”: the maximum power is 4.5 Kw.

“P4”: the maximum power is 5.5 Kw.

“P5”: the maximum power is 7.2 Kw.

OR

Confirmation and Exit Power Management Function

Press at the same time the “+”(timer) and Pause for confirmation, then the hob will be

turned off.

14

Using Boost function

Activate the boost function

1. Touch the slider control of which zone you want to select.

Note: The power setting of bridge zone works the same as any other normal area.

2. Touch the booster key when the display is blinking,

power level indication shows “P”.

Cancel Boost function

1. Touching the “slider” to cancel the Boost function, and

select the level you want to set.

• Boost function can only last for 5 minutes, after that the zone will go to level 9

automatically.

Using Automatic detection Function

If activating the Automatic detection function, it will automatically detect and show

where the pan is.

Activate the Automatic detection function

Press the Automatic detection key to activate this function.

Display will show “0” if the pan can be detected.

Cancel the Automatic detection function

Press the Automatic detection key again to cancel this function.

Using Energy Efficiency Function

For induction hobs, the better pot you use, the more efficiency you will get. This EE

function can automatically detect the quality of pots and show the efficiency you use.

Activate the Energy Efficiency function

Press the EE button, EE% indicator will light up. Display will

show the percentage of power you use.

15

If the timer, keylock or EE functions are activated at the same time, it will indicate the

corresponding information alternately.

Cancel the Energy Efficiency function

Press the EE button, EE% indicator will go out and the function is

canceled.

Using the Keep Warm function

Activate the Keep warm function

1. Touch the slider control of which zone you want to set.

2. Touching the keep warm control, the zone indication

shows “ |”

Cancel the Keep warm function

Touch the slider control of which zone you want to cancel the Keep warm, then the

cooking zone will revert to the level you select.

Using the Pause function

1. Press the Pause control the heating zones stop working. All the zone indication

show“||”

2. Press the Pause control once again, all the heating zones will revert to its

original setting.

The function is available when one or more heating zones are working.

If you don`t cancel the stop working mode within 30 minutes, the induction hob

will automatically switch off.

Locking the Controls

•You can lock the controls to prevent unintended use (for example children

accidentally turning the cooking zones on).

16

•When the controls are locked and heating zones are working, all the controls except

the ON/OFF and Pause are disabled.

To lock the controls

Touch the keylock control.

The timer indicator will show “Lo “.

To unlock the controls

1. Make sure the hob is turned on.

2. Touch and hold the keylock control for 3 seconds.

3. You can now start using your hob.

When the hob is in lock mode and without heating zone working, all the controls

are disabled excepting the ON/OFF, you can always turn the hob off with the

ON/OFF control in an emergency, but you shall unlock the hob first in the next

operation.

Residual Heat Warning

When the hob has been operating for some time, there will be some

residual heat. The letter “H” appears to warn you to keep away from it.

Using Flexible zone function (only for HTP644MCBB)

This may be used as a single zone or two individual zones depending on the

cooking needs in each situation.

It is made of two independent coils that can be controlled separately. When the

flexible zone is working, only the zone covered by the cookware is activated. This

function only works on 1# and 2# cooking zones.

To ensure that the cookware is detected and heat is distributed evenly, correctly

centre the cookware.

17

One hob with more than one flexible zone, it is not recommended to use several

zones at the same time for a single pan.

Activate Flexible zone function

1. To activate the flexible area as a single big zone, touch the key. The buzzer

beeps indicating that the induction hob enters selection of flexible zone, and the

corresponding indicator will flash.

2. Select the power level you want to set by touch “Slider”control.

Cancel Flexible zone function

1. Touch the key to cancel the flexible zone function.

2. The power setting works the same as any other normal area.

18

Auto Shutdown

Safety feature of the hob is auto shut down. This occurs whenever you forget to switch

off a cooking zone. The default shutdown times are shown in the table below:

Power level

1

2

3

4

5

6

7

8

9

Default working timer (hour)

8

4

2

Using the Timer

You can use the timer in two different ways:

You can use it as a minute minder. In this case, the timer will not turn any cooking

zone off when the set time is up.

You can use it as cut-off timer to turn one or more cooking zones off after time is

up.

You can set the timer up to 99 minutes.

Using the Timer as a Minute Minder

1. Make sure the hob is turned on. And zone selection key is not activated (zone

indication ‘-’ is not blinking).

Note: You can set minute minder before or after cooking zone power setting finished.

2. Set the time by touching “+””-”.

Press the “+” once increases the time by one minute, Press

the “-” once decrease the time by one minute. When the set

time exceed 99 minutes, it will automatically return to “00”,

if the “-” and “+” keys are pressed simultaneously, the

indicator will display “00”.

3. When the time is set, it will begin to count down immediately. The display will

show the remaining time.

4. Buzzer will beeps for 30 seconds and the timer indicator shows

“- - ” when the setting time finished.

19

Using the timer to switch off one or more cooking zones

1. Press the slider control of which cooking zone you want to

set the timer for.

2. Set the time by touching “+” “-”.

Press the “+” once increases the time by one minute, Press the

“-” once decrease the time by one minute. When the set time

exceed 99 minutes, it will automatically return to “00”, if the “-”

and “+” keys are pressed simultaneously, the indicator will

display “00”.

3. When the time is set, it will begin to count down immediately. The display will show

the remaining time.

NOTE: There will be a red dot in the right bottom corner of power level indication

which indicating that zone is selected.

4. When cooking timer expires, the corresponding cooking zone will be switch off

automatically.

Note: Other cooking zones will keep operating if they are turned on previously.

If the timer is set on more than one zone:

1. When you set timer for several cooking zones, red dots of the relevant cooking

zones are indicated. The timer display shows the min. timer. The dot of the

corresponding zone blinks.

(set to 15 minutes)

(set to 45 minutes)

2. Once the countdown timer expires, the corresponding zone will switch off.

Then it will show the new min. timer and the dot of corresponding zone will flash.

Stránka sa načítava...