Ingersoll Rand QX Serie Používateľská príručka

QX Series Display

User Manual

Save These Instructions

48619852

Edition 1

July 2012

Εγχειρίδιο Χρήστη

EL

Manual do Utilizador

PT

Käyttöopas

FI

Brukerhåndbok

NO

Bruksanvisning

SV

Brugervejledning

DA

Gebruikershandleiding

NL

Benutzerhandbuch

DE

Manuale per l’uente

IT

Manuel d’utilisation

FR

Manual de usuario

ES

User Manual

EN

SL

Uporabniški priročnik

SK

Používateľská príručka

CS

Návod pro uživatele

ET

Kasutusjuhend

LT

Naudotojo vadovas

LV

Lietotāja rokasgrāmata

RU

Руководство пользователя

ZH

用户手册

JA

ユーザーマニュアル

KO

사용자 설명서

Podręcznik użytkownika

PL

BG

Ръководство на потребителя

Manual de utilizare

RO

HU

Felhasználói kézikönyv

48619852_ed1 EN-1

EN

Purpose of the document:

This document provides details about dierent menu screens, their description and how to edit those screens in display

module, required for the operation of QX Series Hand Tool.

The image Below shows the display of QX Series display module with descriptions of the programming keys.

Symbol Function

Escape / Exit

Enter / Edit

UP

DOWN

RIGHT

LEFT

ESCAPE

LEFT

DOWN

UP

ENTER

RIGHT

EN-2 48619852_ed1

EN

1. Overview of dierent Menu screens

Power up QX Series tool

RUN SCREEN

Press “UP” key

Number being used

Always Press “UP” key to

go to next screen

Press “ENTER” to enter “EDIT” mode

Password screen

Current fault

Status screen with shunt

cal, wireless strength and

battery level.

Cycle Count

Target Angle, Low

and High screen

Target Torque Low

and High screen

RUN SCREEN

Press “UP” key to

increment the value

Press “DOWN” key to

decrement the value

Press “ENTER” to select

the changed values.

Press “ESC” to undo and

keep the old values.

After display is unlocked

Press “RIGHT” Key

Press “UP” key to go to

next screen

Save or Ignore changes. If not on

Save screen, use the up or down

key to scroll to the Save screen.

Press “UP” key to scroll

on one by one to get

below editable screens

in seriesscreen.

48619852_ed1 EN-3

EN

Strategy – Angle or Torque

Direction – Clock wise or anti

clockwise

Unit of Torque

Target Angle (Angle strategy) OR

Target torque (Torque strategy)

Torque High

Torque Low

Angle High

Angle Low

Torque threshold

Free Speed

Shift down torque

Shiftdown Speed

Gang count

Enable / disable RF module

Save / ignore the changes

settings

EN-4 48619852_ed1

EN

2. Description of the Display screen in detail

There are three sections in the QX Series display screen, one “PRIMARY” on the top and two “SECONDARY” which are on

left and right bottom of the display.

2.1. Run Screen

Pressing “ENTER” key after switching on the display will show this image.

PRIMARY Section - shows latest peak torque (for a torque strategy) or the latest peak angle (for an angle strategy), with

units.

The SECONDARY LEFT - shows the cycle count or gang count, if gang count is programmed.

The SECONDARY RIGHT - shows the active conguration number.

48619852_ed1 EN-5

EN

2.2. Conguration

Pressing “UP” will advance to next screen.

Screen shows CONFIGURATION setting used in the tool.

NOTE: Only Conguration 1 can be programmed through the display module.

Pressing “ENTER” will enable the “EDIT MODE” (This procedure to enter “EDIT MODE” is same for all settings update).

EN-6 48619852_ed1

EN

“UP” or “DOWN” key can be used to update the conguration. Pressing “ENTER” again will select the modied

conguration.

2.3. Password

The password screen shows whether the display is locked or unlocked. If the display is locked the parameters of the QX

Series Hand tool cannot be edited.

48619852_ed1 EN-7

EN

Password can be changed by entering into “EDIT MODE” and using “UP” or “DOWN” key.

If “1234” is entered on the Password screen, the user may use the left arrow to go to the Tool ID and software version

page.

The Primary Display is the “Tool Location ID”.

Lower Secondary Right is the “Display Firmware” Version.

Lower Secondary Left is the “Motor Controller Firmware” Version.

EN-8 48619852_ed1

EN

Displays Tool time in HH:MM:SS format. Press the Down key to display the tool time in HH:MM:SS format.

Remaining screens are for internal use only to view log location. Press the Down key to display a screen for internal use

only to view log location. Press the Down key again to display a second log screen.

Press the Down key again to return to the Tool ID page. Pressing the right arrow from this page exits back to the

password display.

48619852_ed1 EN-9

EN

Press ‘ENTER’ to enter the ‘EDIT’ mode. Enter the appropriate password to unlock the tool. Press ‘ENTER’ to exit the ‘EDIT’

mode.

2.3.1. Updating parameters of the QX Series tool

After display is unlocked with a valid password, Pressing “RIGHT” key will advance to following settings that can be

modied as required.

The settings can be modied by entering “EDIT MODE” and using “UP” or “DOWN” key or “RIGHT” or “LEFT” key as

required.

2.3.2. Radio Enable/Disable

This screen allows the user to enable or disable the radio module. The selection on the left disables the radio module

and the selection on the right enables the radio module.

RADIO DISABLED

RADIO ENABLED

EN-10 48619852_ed1

EN

2.3.3. Gang count

The below screen shows the gang count number of bolts to be fastened per Group, Gang, or Set for Conguration 1.

This can be modied by entering “EDIT MODE”.

2.3.4. Shiftdown Speed

This screen indicates shiftdown speed of the QX Series tool. Shiftdown speed can be edited by entering “EDIT MODE”

and updating using UP and DOWN arrow. Programmed speed is a percentage of tool maximum speed.

48619852_ed1 EN-11

EN

2.3.5. Shiftdown Point Cong

This screen indicates “Torque Threshold for shiftdown point”. This can be changed by entering “EDIT MODE” and

updating using “UP” or “DOWN” key.

2.3.6. Free Speed

The below screen indicates free speed of the QX Series tool. The value can be edited by entering “EDIT” mode and using

“UP” and “DOWN” arrow. Programmed speed is a percentage of tool maximum speed.

EN-12 48619852_ed1

EN

2.3.7. Torque Threshold

The Torque at which reading of the angle will be started. The value can be edited by entering “EDIT” mode and using

“UP” and “DOWN” arrow.

2.3.8. Angle

Angle “LOW” Display

Angle “LOW” can be modied in this mode by

entering “EDIT” mode and using “UP or “DOWN” key.

Angle “HIGH” Display

Angle “HIGH” can be modied in this mode by

entering “EDIT” mode and using “UP or “DOWN” key.

48619852_ed1 EN-13

EN

2.3.9. Torque

Torque “LOW” Display

Torque “LOW” can be modied in this mode by

entering “EDIT” mode and using “UP or “DOWN” key.

Torque “HIGH” Display

Torque “HIGH” can be modied in this mode by

entering “EDIT” mode and using “UP or “DOWN” key.

Torque “TARGET” Display.

Torque “TARGET” can be modied in this mode by entering “EDIT” mode and using “UP or “DOWN” key.

EN-14 48619852_ed1

EN

2.3.10. Unit of the Torque

Indicates unit of the Torque displayed in Conguration 1.

This can be changed by entering “EDIT MODE” and updating using “UP” or “DOWN” key.

2.3.11. Direction of Rotation

Image shows direction of rotation in which the QX Series hand tool rotates. Indicates counter clock wise rotation.

Indicates clock wise rotation

This can be changed by entering “EDIT MODE” Key and updating using “RIGHT” or “LEFT” key.

48619852_ed1 EN-15

EN

2.3.12. Strategy

This screen indicates conguration strategy being used.

Left – Angle, Right – Torque.

The pointing arrow indicates the present conguration being used.

This can be changed by entering “EDIT MODE” and using “RIGHT” or “LEFT” key.

2.3.13. Save / Ignore Settings

After all the required changes are completed, Press enter to highlight the save settings box on the left. Press the right or

left arrow key to select cancel on the right. Pressing enter a second time causes the tool to leave edit mode.

SAVE SETTINGS

CANCEL SETTINGS

EN-16 48619852_ed1

EN

2.4. Warning Screen

This is the next screen obtained after pressing “UP” key when QX Series displays the Password screen.

2.5. Shunt Calibration, RF Signal Strength and Battery level

This is the next screen obtained after pressing “UP” key when QX Series displays password screen.

Primary display indicates Shunt Calibration Value.

Secondary display on left indicates RF signal strength and the one on the right indicates Battery Level.

48619852_ed1 EN-17

EN

2.6. Cycle count

This value shows number of cycles run by the QX Series tool, Since the last time it was changed.

With the tool unlocked, press ‘ENTER” key to edit this screen. Press either the ‘UP’ or ‘DOWN’ key to clear the cycle count.

For this change to be retained a cycle must be run before removing power to the tool. Otherwise, the old cycle count is

restored.

2.7. Angle

Primary display – Target Angle.

Secondary Display on left - Angle low.

Secondary Display on right - Angle High.

EN-18 48619852_ed1

EN

2.8. Torque

Primary Display -Target Torque.

Secondary display on left - Torque low.

Secondary display on Right - Torque high.

Pressing “UP” advances back to “RUN SCREEN”, the rst display screen.

Stránka sa načítava ...

Ingersoll Rand QX Serie Používateľská príručka

Táto príručka je tiež vhodná pre

Ingersoll Rand QX Serie Používateľská príručka

V iných jazykoch

Ďalšie dokumenty