Whirlpool AQSF 09 U (EU) Užívateľská príručka
- Kategória
- Práčky
- Typ
- Užívateľská príručka
EN
1
English,1
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
Technical data
Description of the machine, 4-5
Control panel
Running a wash cycle, 6
Wash cycles and options, 7
Table of wash cycles
Wash options
Detergents and laundry, 8
Detergent
Preparing the laundry
Washing recommendations
Load balancing system
Precautions and advice, 9
General safety
Disposal
Opening the porthole door manually
Care and maintenance, 10
Cutting off the water and electricity supplies
Cleaning the machine
Cleaning the detergent dispenser drawer
Caring for your appliance drum
Cleaning the pump
Checking the water inlet hose
Trouble shooting, 11
Assistance, 12
EN
WASHING MACHINE
AQUALTIS
AQSF 09 U
Instructions for
installation and use
Slovensky,13
SK
EN
2
Installation
This instruction manual should be kept in a safe place
for future reference. If the washing machine is sold,
given away or moved, please ensure the manual is kept
with the machine, so that the new owner may benefit
from the advice contained within it.
Read these instructions carefully: they contain vital
information relating to the safe installation and operation
of the appliance.
Inside the pack containing this manual, you will also
find the guarantee and all the details necessary for
installation.
Unpacking and levelling
Unpacking
1. Once you have removed all the packaging from the
washing machine, make sure it has not been damaged
during transportation.
If it has been damaged, contact the retailer and do not
proceed any further with the installation process.
2. Remove the 4
protective screws (used
during transportation) and
the corresponding spacer,
located on the rear part of
the appliance (see figure).
3. Close off the holes using the plastic plugs supplied in
the pack.
4. Keep all the parts in a safe place; they will be needed
again if the washing machine is moved to another
location, to prevent the inside of the appliance being
damaged.
Packaging materials should not be used as toys for
children.
Levelling
1. Place the washing machine on a flat sturdy floor,
without resting it up against walls or cabinets.
2. If the floor is uneven,
the front feet of the
machine may be adjusted
until it reaches a horizontal
position (the angle of
inclination must not
exceed 2 degrees).
If the appliance is levelled correctly, it will be more
stable and much less likely to cause vibrations and noise
while it is operating, particularly during the spin cycle.
If it is placed on carpet or a rug, adjust the feet in such
a way as to allow a sufficient ventilation space
underneath the washing machine.
Connecting the electricity and water
supplies
Connecting the water inlet hose
Before connecting the inlet hose to the water supply,
run the water until it is perfectly clear.
1. Connect the inlet hose
to the machine by
screwing it onto the cold
water inlet of the
appliance, which is
situated on the top right-
hand side of the rear part
of the appliance (see
figure).
2. Connect the inlet hose
by screwing it to a cold
water tab using a 3/4 gas
threaded connection (see
figure).
3. Make sure that the hose is not folded over or bent.
The water pressure at the tap must fall within the
values indicated in the Technical data table (see next
page).
If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.
Never use second-hand or old inlet hoses; use the
products supplied with the machine.
EN
3
65 - 100 cm
Connecting the drain hose
Connect the drain hose to
drain duct piping or a wall
drain located between 65
and 100 cm above the
floor, making sure it is not
bent at all.
Alternatively, rest the drain
hose on the side of a
washbasin or bathtub,
fastening the duct
supplied to the tap (see
figure).
The free end of the hose
should not be underwater.
We advise against the use of hose extensions; if it is
absolutely necessary, the extension must have the same
diameter as the original hose and must not exceed 150
cm in length.
Electrical connections
Before plugging the appliance into the electricity socket,
make sure that:
the socket is earthed and complies with all applicable
laws;
the socket is able to withstand the maximum power
load of the appliance as indicated in the Technical
data table (see opposite);
the power supply voltage falls within the values
indicated in the Technical data table (see opposite);
the socket is compatible with the plug of the
appliance. If this is not the case, have the socket or
the plug replaced.
The machine must not be installed outdoors, even in
covered areas. It is extremely dangerous to leave the
appliance exposed to rain, storms and other weather
conditions.
The mains socket must remain within easy reach after
the washing machine has been installed.
Do not use extension cords or multiple sockets.
The cable should not be bent or compressed.
The power supply cable and plug must only be
replaced by authorised technicians.
Warning! The company shall not be held responsible in
the event that these regulations are not respected.
Technical data
Model
AQSF 09 U
Dimensions
width 59.5 cm
height 85 cm
depth 47 cm
Capacity
from 1 to 6 kg
Electrical
connections
please refer to the technical data
plate fixed to the machine
Water connections
maximum pressure 1 MPa (10 bar)
minimum pressure 0.05 MPa (0.5 bar)
drum capacity 40 litres
Spin speed
up to 1000 rotations per minute
Energy rated
programmes
according to
regulation
EN 60456
programme ; temperature 60°C;
using a load of 6 kg.
This appliance conforms to the
following EC Directives:
- 89/336/EEC dated 03/05/89
(Electromagnetic Compatibility) and
subsequent modifications
- 2006/95/EC (Low Voltage)
- 2002/96/EC
EN
4
CONTROL
PANEL
PORTHOLE DOOR
PORTHOLE DOOR
HANDLE
KICK STRIP
ADJUSTABLE FEET
3
1
2
Description of the machine
PORTHOLE DOOR
Always use the handle to
open the porthole door (see
figure).
DETERGENT DISPENSER DRAWER
The detergent dispenser
drawer is located inside the
machine and can be
accessed by opening the
door.
For more information on
detergent measures, please
refer to the chapter entitled
Detergents and laundry.
Note: stick the label showing
the wash cycle descriptions and options on the front of
the detergent dispenser drawer. You will find the sticker
in the pack containing this manual.
1. pre-wash compartment:
use powder detergent.
Before pouring in the
detergent, make sure that
extra compartment 3 has
been removed.
2. main wash compartment:
use powder or liquid
detergent. If using the latter
type of detergent, we
recommend it is poured into
the drawer immediately before you start the washing
machine.
3. extra compartment: Bleach
The use of extra compartment 3 excludes the pre-
wash function.
washing additives compartment: for fabric softener or
liquid additives. We recommend that the maximum level
indicated by the grille is not exceeded, and that
concentrated fabric softeners are diluted.
Standby mode
This washing machine, in compliance with new energy
saving regulations, is fitted with an automatic standby
system which is enabled after about 30 minutes if no
activity is detected. Press the ON-OFF
button briefly
and wait for the machine to start up again.
EN
5
TEMPERATURE button
WASH CYCLE
SELECTOR knob
OPTION buttons with
indicator lights
DOOR LOCKED
indicator light
START/PAUSE
button with indicator
light
WASH
CYCLE
PHASE
icons
SPIN button
DELAYED
START
button
CONTROL PANEL
LOCK button with
indicator light
Button withON/OFF
indicator light
ECO indicator light
OPTION buttons with
indicator lights
TEMPERATURE
display
SPIN display
DELAYED START/CYCLE
DURATIONdisplay
Control panel
Button with ON/OFF indicator light: press this briefly
to switch the machine on or off. The green indicator light
indicates that the machine is switched on. To switch off
the washing machine during the wash cycle, press and
hold the button for approximately 3 seconds; if the
button is pressed briefly or accidentally the machine will
not switch off. If the machine is switched off during a
wash cycle, this wash cycle will be cancelled.
WASH CYCLE SELECTOR knob: may be turned in
either direction. To select the most suitable wash cycle,
please refer to the Table of wash cycles.
The knob will not move during the wash cycle.
TEMPERATURE
button: press to modify or exclude
the temperature setting; the value selected will appear
on the display above (see Running a wash cycle).
SPIN CYCLE
button: press to modify or exclude the
spin cycle; the value selected will appear on the display
above (see Running a wash cycle).
DELAYED START
button: press to set a delayed start
for the selected wash cycle; the set delay time will appear
on the display above (see Running a wash cycle).
OPTION buttons with indicator lights: press to select the
available options. The indicator light corresponding to the
selected option will remain lit (see Running a wash cycle).
WASH CYCLE PHASE icons: these illuminate to
indicate the progress of the wash cycle (Wash
Rinse
Spin Drain ).
The text
lights up when the cycle is complete.
START/PAUSE button with indicator light: when the
green indicator light flashes slowly, press the button to
start a wash cycle. Once the cycle has begun the
indicator light will remain lit in a fixed manner. To pause
the wash cycle, press the button again; the indicator
light will flash in an orange colour. If the Door locked
indicator light is switched off, the door may be
opened. To start the wash cycle from the point at which
it was interrupted, press the button again.
DOOR LOCKED
indicator light: indicates that the
porthole door is locked. To open the door, pause the
wash cycle (see Running a wash cycle).
CONTROL PANEL LOCK
button with indicator
light: to activate or deactivate the control panel lock,
press and hold the button for approximately 2 seconds.
when the indicator light is illuminated, the control panel is
locked. This means it is possible to prevent wash cycles
from being modified accidentally, especially where there
are children in the home.
ECO indicator light: the
icon lights up when, after
altering the washing parameters, an energy saving of at
least 10% is made. Furthermore, before the machine
enters Standby mode, the icon will light up for a few
seconds; when the machine is switched off the
estimated energy saving will be around the 80% mark.
EN
6
WARNING: before you use the washing machine for
the first time, run a wash cycle with detergent and no
laundry, using the 90° cottons cycle without pre-wash.
1. SWITCH THE MACHINE ON. Press the
button.
All the indicator lights will illuminate for 1 second; the
indicator light corresponding to the
button will then
remain lit in a fixed manner and the START/PAUSE
indicator light will flash slowly.
2. LOAD THE LAUNDRY. Open the porthole door.
Load the laundry, making sure you do not exceed the
maximum load value indicated in the table of wash
cycles on the following page.
3. MEASURE OUT THE DETERGENT. Pull out the
detergent dispenser drawer and pour the detergent
into the relevant compartments as described in
Description of the machine.
4. CLOSE THE PORTHOLE DOOR.
5. SELECT THE PROGRAMME. Turn the WASH
CYCLE SELECTOR KNOB right or left, until you have
selected the desired wash cycle. A temperature and
spin speed is set for each wash cycle; these may be
adjusted.
6. CUSTOMISE THE WASH CYCLE. Use the
relevant buttons on the control panel:
Modify the temperature and/or spin
speed.
The machine automatically displays the maximum
temperature and spin speed values set for the
selected cycle, or the most recently-used settings if
they are compatible with the selected cycle. The
temperature can be decreased by pressing the
button, until the cold wash ( ) setting is reached.
The spin speed may be progressively reduced by
pressing the
button, until it is completely excluded
(
). If these buttons are pressed again, the
maximum values are restored.
Exception: if the Cottons programme is selected,
the temperature can be increased up to a value of
90°C.
Set a delayed start.
Press the button until you have reached the desired
delay time. During the setting process, the delay time
is shown on the display and the
symbol flashes.
After selecting a delayed start time, the fixed
symbol and the cycle duration will appear on the
display. Press the button once to display the selected
delay time.
To remove the delayed start option, press the button
until the display shows the text OFF; the
symbol
will disappear.
Once the START/PAUSE button has been pressed,
the time delay may only be decreased.
Modify the cycle settings.
Press the OPTION buttons to customise the wash
cycle in accordance with your own requirements.
Press the button to activate the option; the
corresponding indicator light will switch on.
Press the button again to disable the option; the
indicator light will switch off.
If the selected option is not compatible with the
selected wash cycle, this incompatibility will be
signalled by the flashing of the indicator light and a
sound alert (3 beeps); the option will not be activated.
If the selected option is not compatible with another
option that has been selected previously, the indicator
light corresponding to the first option selected will flash
and only the second option will be activated; the
indicator light corresponding to the button will remain
lit in a constant manner.
7. START THE PROGRAMME. Press the START/
PAUSE button. The corresponding indicator light
remains lit in a fixed manner and the porthole door
locks (the
DOOR LOCKED indicator light
illuminates). The icons corresponding to the wash
cycle phases will light up during the cycle to indicate
which phase is currently in progress.
To change a wash cycle once it has already started,
pause the washing machine by pressing the START/
PAUSE button; then select the desired cycle and
press the START/PAUSE button again.
To open the door during a wash cycle, press the
START/PAUSE button; if the DOOR LOCKED
indicator light is switched off you may open the door.
Press the START/PAUSE button again to restart the
wash cycle from the point at which it was interrupted.
8. THE END OF THE WASH CYCLE. This is indicated
by the illuminated text END. The porthole door may
be opened immediately. If the START/PAUSE indicator
light is flashing, press the button to end the cycle.
Open the door, unload the laundry and switch off the
machine.
If you wish to cancel a cycle which has already begun,
press and hold the
button until the cycle stops and
the machine switches off.
Running a wash cycle
EN
7
Wash options
Super Wash
This option offers a high-performance wash due to the
greater quantity of water used in the initial phase of the
cycle, and due to the increased wash cycle duration, is
particularly useful for the
removal of stubborn stains.
It can be used with or
without bleach. If you desire
bleaching, insert the extra
tray compartment (3) into
compartment 1. When
pouring in the bleach, be
careful not to exceed the
max level marked on the
central pivot (see figure).
To bleach laundry without
carrying out a full wash cycle, pour the bleach into the
extra compartment 3, select the "Rinse" cycle
and
activate the "Super Wash" option
.
It cannot be used in conjunction with
, , , , ,
, , .
Easy Iron
By selecting this option, the wash and spin cycles will be
modified in order to reduce the formation of creases.
At the end of the cycle the washing machine
drum will rotate slowly; the Easy Iron and START/
PAUSE indicator lights will flash. To end the cycle press
the START/PAUSE button or the Easy Iron button.
For the Silk
wash cycle, the machine will end the
cycle while the laundry is soaking and the Easy
Iron indicator light will flash. To drain the water so that
the laundry may be removed, press the START/PAUSE
button or the Easy Iron button.
It cannot be used in conjunction with
, , , , .
Time Saver
If you select this option, the wash cycle duration will be
reduced by 30%-50%, depending on the selected cycle,
thereby guaranteeing simultaneous water and energy
saving. Use this cycle for lightly soiled garments.
It cannot be used in conjunction with
, , , ,
, , , , .
Extra rinse
By selecting this option, the efficiency of the rinse is
increased and optimal residual detergent removal is
guaranteed. It is particularly useful for skin which is
sensitive to detergents. We recommend this option is
used with a full load of washing, or when a large amount
of detergent is required.
It cannot be used in conjunction with
, , .
3
1
2
(*) The duration of the wash cycles can be checked
on the display.
(*) Note: 10 minutes after the START, the machine will recalculate the time remaining until the end of the wash cycle on the basis of the load inside it; this
value will then be shown on the display.
Wash cycles and options
Table of wash cycles
For all Test Institutes:
1) Test wash cycle in compliance with regulation EN 60456: set wash cycle
with a temperature of 60°C.
2) Long wash cycle for cottons: set wash cycle
with a temperature of 40°C.
3) Short wash cycle for cottons: set wash cycle
with a temperature of 40°C.
Icon Description of the wash cycle
Max.
temp.
(°C)
Max.
speed
(rpm)
Detergent and additives
Max.
load
(kg)
Cycle
duration
Detergent
for wash
Fabric
softener
Bleach
Cottons wash cycles
Cottons
with pre-wash
(Add detergent to the relevant compartment).
90° 1000
ll
- 6
Cottons (1):
heavily soiled whites and resistant colours.
60°
(Max. 90°)
1000
lll
6
Cottons (2):
heavily soiled whites and delicate colours.
40° 1000
lll
6
Coloured
Cottons (3)
40° 1000
lll
6
Shirts
40° 600
lll
2
Jeans
40° 800
ll
- 2,5
Special programmes
Baby:
heavily soiled delicate colours
40° 800
lll
2
Durable
Synthetics
60° 800
lll
2,5
Delicate
Synthetics
40° 800
lll
2,5
"Bed & Bath"
for bedlinen and towels.
60° 1000
lll
6
Quilted Jacket:
for down-stuffed garments.
30° 1000
ll
- 1
Silk:
for garments in silk and viscose, lingerie.
30° 0
ll
- 1
Wool:
for wool, cashmere, etc.
40° 600
ll
- 1
Mix 30':
to refresh lightly soiled garments quickly (not suitable for
wool, silk and clothes which require washing by hand)
30° 800
ll
- 3
Partials wash cycles
Rinse - 1000 -
ll
6
Spin - 1000 - - - 6
Drain - 0 - - - 6
EN
8
Detergents and laundry
Detergent
The type and quantity of detergent required depend on
the type of fabric you are washing (cotton, wool, silk,
etc.), as well as its colour, the washing temperature, the
level of soiling and the hardness of the water in the area.
Measuring out the detergent carefully will avoid wastage
and help to protect the environment: although they are
biodegradable, detergents still contain ingredients which
alter the balance of nature.
We recommend the following:
use powder detergents for white cotton garments and
pre-washing.
use liquid detergents for delicate cotton garments and
for all low-temperature wash cycles.
use gentle liquid detergents for wool and silk
garments.
The detergent should be poured into the relevant
compartment - or the dispenser placed directly inside
the drum - before the wash cycle begins. In the latter
case, it will not be possible to select the Cottons with
pre-wash cycle.
Do not use hand washing detergents because these
create too much foam.
Preparing the laundry
Shake out the garments before loading them into the
machine.
Divide the laundry according fabric type (symbol on
the washing instruction label) and colour, making sure
you separate the coloured garments from the white
ones;
Empty all pockets and check the buttons;
Do not exceed the values listed in the Table of wash
cycles, which refer to the weight of the laundry when
dry.
How much does your laundry weigh?
1 sheet 400-500 g
1 pillowcase 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1200 g
1 towel 150-250 g
1 pair of jeans 400-500 g
1 shirt 150-200 g
Washing recommendations
Shirts: use the special Shirts wash cycle to wash
shirts in different fabrics and colours to guarantee they
receive the best possible care.
Jeans: use the special Jeans
wash cycle for all
denim garments; turn inside out before washing and use
a liquid detergent.
Baby: use the special Baby
wash cycle to remove
the remove the soiling typically caused by babies, while
removing all traces of detergent from nappies in order to
prevent the delicate skin of babies from suffering allergic
reactions. The cycle has been designed to reduce the
amount of bacteria by using a greater quantity of water
and optimising the effect of special disinfecting additives
added to the detergent. At the end of the wash cycle,
the machine will slowly rotate the drum; to end the cycle
press the START/PAUSE button.
Silk: use the special Silk
wash cycle to wash all silk
garments. We recommend the use of special detergent
which has been designed to wash delicate clothes.
Curtains: use the Silk
wash cycle. Fold curtains
and place them in a pillow case or mesh bag.
Wool: is the only washing machine brand to have been
awarded the prestigious Woolmark Platinum Care
endorsement (M.0508) by the Woolmark Company,
which means that all woollen garments may be washed
in the washing machine, even those which state hand
wash only
on the label. The Wool wash cycle can
be used to wash all woollen garments in the washing
machine while guaranteeing optimum performance.
Quilted Jacket: to wash quilted jacket, cushions or
clothes padded with goose down (the weight of which
should not exceed 1 kg), use the special Quilted
Jacket
wash cycle.
Bedlinen and towels: use the Bed & Bath
cycle
to wash laundry from all over the house; this optimises
fabric softener performance and helps you save time and
energy. We recommend the use of powder detergent.
Stubborn stains: it is wise to treat stubborn stains with
solid soap before washing, and to use the Cottons with
pre-wash cycle.
Load balancing system
Before every spin cycle, to avoid excessive vibrations
before every spin and to distribute the load in a uniform
manner, the drum rotates continuously at a speed which
is slightly greater than the washing rotation speed. If,
after several attempts, the load is not balanced
correctly, the machine spins at a reduced spin speed. If
the load is excessively unbalanced, the washing
machine performs the distribution process instead of
spinning. To encourage improved load distribution and
balance, we recommend small and large garments are
mixed in the load.
EN
9
Precautions and tips
The machine was designed and constructed in
accordance with international safety regulations. The
following information is provided for safety reasons and
must therefore be read carefully.
General safety
This appliance was designed for domestic use only.
This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety. Children should be
supervised to ensure that they do not play with the
appliance.
Do not touch the machine when barefoot or with wet
or damp hands or feet.
Do not pull on the power supply cable when
unplugging the appliance from the electricity socket.
Hold the plug and pull.
Do not touch the drained water as it may reach
extremely high temperatures.
Never force the porthole door. This could damage the
safety lock mechanism designed to prevent
accidental opening.
If the appliance breaks down, do not under any
circumstances access the internal mechanisms in an
attempt to repair it yourself.
Always keep children well away from the appliance
while it is operating.
If it must be moved, proceed with the help of two or
three people and handle it with the utmost care.
Never try to do this alone, because the appliance is
very heavy.
Before loading laundry into the washing machine,
make sure the drum is empty.
Disposal
Disposing of the packaging materials: observe local
regulations so that the packaging may be re-used.
The European Directive 2002/96/EC relating to Waste
Electrical and Electronic Equipment (WEEE) states
that household appliances should not be disposed of
using the normal solid urban waste cycle. Exhausted
appliances should be collected separately in order to
optimise the cost of re-using and recycling the
materials inside the machine, while preventing
potential damage to the atmosphere and to public
health. The crossed-out dustbin is marked on all
products to remind the owner of their obligations
regarding separated waste collection.
For more information relating to the correct disposal of
household appliances, owners should contact their
local authorities or appliance dealer.
Opening the porthole door manually
In the event of a powercut, the door may be opened in
order to remove the laundry from the machine. Proceed
as follows:
1. Remove the plug from the
electrical socket.
2. To prevent water from
escaping when the door is
opened, make sure that the
level of the water is lower
than the seal around the
porthole door; if this is not
the case, remove any
excess water using the drain
hose (see figure).
3. Insert the key supplied with the appliance into the
groove at the side, as illustrated in the figure.
4. Press down on the key while pulling the handle
outwards to open the door.
EN
10
1
2
Cutting off the water and electricity
supplies
Turn off the water tap after every wash cycle. This will
limit wear on the hydraulic system in the machine and
help to prevent leaks.
Unplug the appliance when cleaning it and during all
maintenance work.
Cleaning the machine
The outer parts and rubber components of the appliance
can be cleaned using a soft cloth soaked in lukewarm
soapy water. Do not use solvents or abrasives.
Cleaning the detergent dispenser
drawer
To remove the drawer, press
lever (1) and pull the drawer
outwards (2) (see figure).
Wash it under running
water; this procedure should
be repeated frequently.
Caring for your appliance drum
Always leave the door ajar to prevent unpleasant
odours from forming.
Cleaning the pump
The washing machine is fitted with a self-cleaning pump
which does not require any maintenance. Sometimes,
small items (such as coins or buttons) may fall into the
protective pre-chamber at the base of the pump.
Make sure the wash cycle has finished and unplug the
appliance.
To access the pre-chamber:
1. take off the cover panel on the front of the machine
by first pressing it in the centre and then pushing
downwards on both sides until you can remove it (see
figures);
2. position a container so
that it will collect the water
which flows out
(approximately 1.5 l) (see
figure);
3. unscrew the lid by
rotating it in an anti-
clockwise direction (see
figure);
4. clean the inside thoroughly;
5. screw the lid back on;
6. reposition the panel, making sure the hooks are
securely in place before you push it onto the appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If there are
any cracks, it should be replaced immediately: during
the wash cycles, water pressure is very strong and a
cracked hose could easily split open.
1
2
Care and maintenance
EN
11
Trouble shooting
Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Centre
(see Assistance), make sure that the problem cannot be not solved easily using the following list.
Problem:
The washing machine does not
switch on.
The wash cycle does not start.
The washing machine does not fill
with water.
The washing machine door
remains locked.
The machine continuously fills
with water and drains.
The washing machine does not
drain or spin.
The machine vibrates a lot during
the spin cycle.
The washing machine leaks.
The icons corresponding to the
Phase in progress flash rapidly
at the same time as the ON/OFF
indicator light.
There is too much foam.
The washing machine door
remains locked.
Possible causes / Solutions:
The appliance is not plugged into the socket fully, or not enough to make
contact.
There is no power in the house.
The door is not closed properly.
The START/PAUSE button has not been pressed.
The water tap has not been opened.
A delayed start has been set.
The water inlet hose is not connected to the tap.
The hose is bent.
The water tap has not been opened.
There is no water supply in the house.
The pressure is too low.
The START/PAUSE button has not been pressed.
If you have selected the Baby
cycle or the Easy iron option, when
the wash cycle has finished the machine will slowly rotate the drum; to end
the cycle press the START/PAUSE button or the Easy iron
button. If
you have selected the Silk
wash cycle, the machine will end the cycle
while the laundry is soaking; to drain the water so that the laundry may be
removed, press the START/PAUSE button or the Easy iron
button.
The drain hose is not fitted at a height between 65 and 100 cm from the
floor (see Installation).
The free end of the hose is under water (see Installation).
If the dwelling is on one of the upper floors of a building, there may be
problems relating to water drainage, causing the washing machine to fill
with water and drain continuously. Special anti-draining valves are available
in shops and help to prevent this inconvenience.
The wall drainage system is not fitted with a breather pipe.
The wash cycle does not include draining: Some wash cycles require the
drain phase to be started manually (see Wash cycles and options).
The Easy iron option is enabled: to complete the wash cycle, press the
START/PAUSE button (Wash cycles and options).
The drain hose is bent (see Installation).
The drainage duct is clogged.
The drum was not unlocked correctly during installation (see Installation).
The machine is not level (see Installation ).
The machine is trapped between cabinets and walls (see Installation).
The load is unbalanced (see Detergents and laundry).
The water inlet hose is not screwed on properly (see Installation).
The detergent dispenser is blocked (to clean it, see Care and
maintenance).
The drain hose is not fixed in place properly (see Installation).
Switch off the machine and unplug it, wait for approximately 1 minute and
then switch it back on again. If the problem persists, contact the Technical
Assistance Service.
The detergent is not suitable for machine washing (it should display the text
for washing machines or hand and machine wash, or the like).
Too much detergent was used.
Perform the manual unlocking procedure (see Precautions and tips).
Note: To exit Demo mode, press and hold the two ON/OFF and START/PAUSE buttons simultaneously for 3 seconds.
EN
12
Before calling for Assistance:
Check whether you can solve the problem by yourself (see Trouble shooting);
Restart the wash cycle to check whether the problem has been solved;
If it has not, contact the Authorised Technical Assistance Service.
If the washing machine has been installed or used incorrectly, you will have to pay for the call-out service.
Always request the assistance of authorised technicians.
Please have the following information to hand:
the type of problem;
the appliance model (Mod.);
the serial number (S/N).
The above information can be found on the data plate located on the appliance itself.
Assistance
13
SK
Slovensky
Obsah
Intalácia, 14-15
Rozbalenie a vyrovnanie do vodorovnej polohy
Pripojenie kelektrickej akvodovodnej sieti
Technické údaje
Popis zariadenia, 16-17
Ovládací panel
Ako vykona prací cyklus, 18
Programy a volite¾né funkcie, 19
Tabu¾ka programov
Volite¾né funkcie prania
Pracie prostriedky a prádlo, 20
Prací prostriedok
Príprava prádla
Rady pre pranie
Systém automatického vyváenia náplne
Opatrenia a rady, 21
Základné bezpeènostné pokyny
Likvidácia
Manuálne otvorenie dvierok s priezorom
Údrba a starostlivos, 22
Uzavretie prívodu vody a vypnutie elektrického napájania
Èistenie zariadenia
Èistenie dávkovaèa pracích prostriedkov
Starostlivos o bubon
Èistenie èerpadla
Kontrola prítokovej hadice na vodu
Poruchy a spôsob ich odstránenia, 23
Servisná sluba, 24
SK
PRÁÈKA
AQUALTIS
AQSF 09 U
Návod na intaláciu a pouitie
SK
14
Intalácia
Je ve¾mi dôleité uschova tento návod za úèelom
jeho ïalej konzultácie. Vprípade predaja, darovania
alebo presahovania práèky zabezpeète, aby zostal
uloený vjej blízkosti.
Pozorne si preèítajte uvedené pokyny: obsahujú
dôleité informácie, týkajúce sa intalácie, pouitia a
bezpeènosti pri práci.
Vobálke stýmto návodom môete nájst okrem
záruky aj súciastky potrebné na intaláciu.
Rozbalenie a vyrovnanie do vodorovnej
polohy
Rozbalenie
1. Po rozbalení práèky skontroluje, èi poèas prepravy
nedolo kjej pokodeniu.
Vprípade, e je pokodená, nezapájajte ju a obráte
sa na predajcu.
2. Odstránte 4 skrutky
chrániace pred
pokodením poèas
prepravy a prísluný
ditanèný clen, ktoré sa
nachádzajú vzadnej èasti
(vid obrázok).
3. Uzatvorte otvory po skrutkách plastovými krytkami,
nachádzajúcimi sa v obálke.
4. Odlote si vetky diely. Vprípade prepravy práèky
bude potrebné vykonat jej opätovnú montá, aby ste
tak predili jej vnútornému pokodeniu.
Obaly nie sú hraèky pre deti! Vetky obaly uschovajte
mimo dosahu dietata, hrozí jeho udusenie!
Vyrovnanie do vodorovnej polohy
1. Práèku je potrebné umiestnit na rovnú a pevnú
podlahu tak, aby nebola opretá o stenu alebo nábytok.
2. Vykompenzujte
nerovnosti odkrútením
alebo zakrútením
noièiek, a kým sa
zariadenie nebude
nachádzat vo vodorovnej
polohe (nesmie byt
naklonená o viac ako 2
stupne).
Dôsledné vyrovnanie do vodorovnej polohy zaistí
stabilitu a zabráni vibráciám a hluènosti, hlavne vo fáze
odstreïovania.
Vprípade intalácie na podlahovú krytinu alebo na
koberec, nastavte noièky tak, aby pod práèkou zostal
dostatoèný volný priestor na ventiláciu.
Pripojenie kelektrickej akvodovodnej sieti
Pripojenie prítokovej hadice vody
Pred pripojením prítokovej hadice krozvodu vody
nechajte odtiec vodu, a kým nebude èíra.
1. Pripojte prítokovú
hadicu kzariadeniu
prostredníctvom príslunej
prípojky na vodu,
umiestnenej vzadnej
èasti, vpravo hore (viï
obrázok).
2. Pripojte prívodnú hadicu
jej zaskrutkovaním ku
kohútiku so studenou
vodou, shrdlom so
závitom 3/4 (vid obrázok).
3. Zabezpeète, aby hadica nebola príli ohnutá alebo
stlaèená.
Tlak vrozvode vody sa musí pohybova vrozmedzí
hodnôt uvedených vtabu¾ke s technickými údajmi (viï
ved¾ajia strana).
Vprípade, e dåka prítokovej hadice nebude
dostatoèná, obráte sa na pecializovanú predajòu
alebo na autorizovaný technický personál.
Nikdy nepouívajte pouité alebo staré prítokové
hadice, ale hadice, ktoré sú súèastou prísluenstva
zariadenia.
15
SK
65 - 100 cm
Pripojenie vypúacej hadice
Pripojte vypútaciu hadicu
kodpadovému potrubiu
alebo kodpadu v stene,
nachádzajúcom sa od 65
do 100 cm nad zemou;
jednoznaène zamedzte jej
ohybu.
Alebo ju zachyte na
okraj umývadla èi vane a
pripevnite ju ku kohútiku
priviazaním driaka
zprísluenstva (viï
obrázok).
Vo¾ný koniec vypúacej
hadice nesmie zosta
ponorený do vody.
Pouitie predlovacích hadíc sa neodporúèa; ak je
vak nevyhnutné, predlovacia hadica musí mat
rovnaký priemer ako originálna hadica a jej dlka
nesmie presiahnut 150 cm.
Pripojenie kelektrickej sieti
Pred zasunutím zástrèky do zásuvky sa uistite, e:
zásuvka je uzemnená a e vyhovuje normám;
zásuvka je schopná unies maximálnu záa
odpovedajúcu menovitému príkonu zariadenia,
uvedenému vtabu¾ke s technickými údajmi (viï
ved¾a);
hodnota napájacieho napätia odpovedá údajom
uvedeným vtabulke stechnickými údajmi (vid
vedla);
sa zásuvka zhoduje so zástrèkou napájacieho kábla
zariadenia. Vopaènom prípade je potrebné da
vymeni zásuvku alebo zástrèku.
Práèka nesmie by umiestnená vonku pod holým
nebom, a to ani vprípade, keby sa jednalo o miesto
chránené pred nepriazòou poèasia, pretoe je ve¾mi
nebezpeèné vystavi ju pôsobeniu daïa a búrok.
Po definitívnom umiestnení práèky musí zásuvka
zosta ¾ahko prístupná.
Nepouívajte predlovacie káble a rozvodky.
Kábel nesmie by ohnutý alebo pritlaèený.
Výmena kábla a zástrèky musí by zverená výhradne
autorizovanému technickému personálu.
Upozornenie! Výrobca neponesie iadnu zodpovednost
za následky spôsobené nerepektovaním týchto
pokynov.
Technické údaje
Model
AQSF 09 U
Rozmery
írka 59,5 cm
výka 85 cm
håbka 47 cm
Kapacita
od 1 do 6 kg
Elektrické zapojenie
viï títok s technickými údajmi,
aplikovaný na zariadení
Pripojenie k rozvodu
vody
maximálny tlak 1 MPa (10 bar)
maximálny tlak 0,05 MPa (0.5 bar)
kapacita bubna 40 litrov
Rýchlos±z
odstreïovania
a±z do 1000 otáèok za minútu
Kontrolný program
pod¾a normy
EN 60456
program ; teplota 6
0°
°°°°°°
C
;
náplò 6 kg prádla.
Toto zariadenie je v zhode s
nasledujúcimi smernicami Európskej únie:
- 89/336/EHS z 03/05/89
(Elektromagnetická kompatibilita)
v platnom znení
- 2002/96/CE
- 2006/95/CE (Nízke napätie)
Hluènost¡
(dB(A) re 1 pW)
Pranie: 54
Odstreïovanie: 75
SK
16
OVLÁDACÍ
PANEL
DVIERKA S
PRIEZOROM
DRADLO DVIEROK
S PRIEZOROM
PODSTAVEC
NASTAVITE¼NÉ
NOIÈKY
3
1
2
Popis zariadenia
DVIERKA S PRIEZOROM
Naotvorenie dvierok
spriezorom pouívajte vdy
prísluné dradlo (vid
obrázok).
DÁVKOVAÈ PRACÍCH PROSTRIEDKOV
Nachádza sa vo vnútri
zariadenia a je knemu
umonený prístup po
otvorení dvierok.
Informácie týkajúce sa
dávkovania pracích
prostriedkov sú uvedené v
kapitole Pracie prostriedky
a prádlo.
Poznámka: Prilepte na
dávkovaè pracích
prostriedkov nálepku spopisom programov
avolitelných funkcií. Nálepka sa nachádza vsáèku
obsahujúcom aj tento návod.
1. priehradka na
predpieranie: pouite
prákový prací prostriedok.
Pred naplnením priehradky
pracím prostriedkom sa
uistite, e vdávkovaèi nie
je vloená prídavná
priehradka 3.
2. priehradka na pranie:
pouite prákový alebo
tekutý prací prostriedok.
Vposlednom uvedenom prípade sa odporúèa nalia
prací prostriedok bezprostredne pred spustením
práèky.
3. prídavná nádobka: Bieliaci prostriedok
Pouitie prídavnej nádobky 3 vyluèuje monos
predpierania.
priehradka pre prídavné pracie prostriedky: pre
tekutú avivá alebo iné tekuté prídavné prostriedky.
Odporúèa sa neprekroèi maximálnu úroveò vyznaèenú
mriekou a rozriedi koncentrovanú avivá.
Pohotovostný reim
Kvôli zhode snovými predpismi súvisiacimi s
energetickou úsporou, je táto práèka vybavená
systémom automatického vypnutia (prechodu do
pohotovostného reimu standby), ktorý je aktivovaný
po uplynutí 30 minút, ak práèka nie je pouívaná.
Krátko stlaète tlaèidlo ON/OFF
avyèkajte na
obnovenie èinnosti zariadenia.
17
SK
Ovládací panel
Tlaèidlo skontrolkou ON/OFF: krátke stlaèenie
tohtotlaèidla slúi na zapnutie alebo vypnutie práèky.
Zelená kontrolka signalizuje, e zariadenie je zapnuté.
Ak chcete vypnú práèku poèas prania, je potrebné
dra tlaèidlo stlaèené dlhie, pribline 3 sek.; krátkym
alebo náhodným stlaèením práèku nevypnete.
Vypnutie zariadenia poèas prania spôsobí zruenie
prebiehajúceho pracieho programu.
Otoèný ovládaè pre VO¼BU PROGRAMOV: je moné
ním otáèa vobidvoch smeroch. Aby ste nastavili
najvhodnejí program, pozrite si Tabu¾ka programov.
Poèas prania zostane otoèný ovládaè bez pohybu.
Tlaèidlo
TEPLOTA: Jeho stlaèenie slúi na zmenu
teploty alebo vylúèenie ohrevu; zvolená hodnota bude
zobrazená na displeji nad tlacidlom (vid Ako vykonat
prací cyklus).
Tlaèidlo
ODSTREÏOVANIE: Jeho stlaèenie slúi na
zmenu rýchlosti alebo vylúèenie odstreïovania; zvolená
hodnota bude zobrazená na displeji nad tlaèidlom (viï
Ako vykona prací cyklus).
Tlaèidlo
ONESKORENÝ TART: Jeho stlaèenie
slúi na nastavenie oneskorenia tartu zvoleného
programu; hodnota nastaveného oneskorenia bude
zobrazená na displeji nad tlaèidlom (viï Ako vykona
prací cyklus).
Tlaèidlá s kontrolkami VOLITE¼NÉ FUNKCIE: Slúi
navo¾bu jednotlivých ponúknutých volite¾ných funkcií.
Prísluná kontrolka zvolenej volite¾nej funkcie zostane
rozsvietená (viï Ako vykona prací cyklus).
Ikony FÁZY PRANIA: Ich rozsvietenie signalizuje
priebeh cyklu (Pranie
- Extra Plákanie -
Odstreïovanie Vypúanie ).
Nápis
sa rozsvieti po ukonèení cyklu.
Tlaèidlo s kontrolkou TART/PAUSE: Keï zelená
kontrolka zaène pomaly blika, stlaète tlaèidlo, aby ste
spustili pranie. Po zahájení cyklu sa kontrolka rozsvieti
stálym svetlom. Ak si eláte prerui pranie, opätovne
stlaète tlaèidlo; kontrolka bude blika oranovým
svetlom. Keï je kontrolka Zablokované dvierka
zhasnutá, je moné otvori dvierka spriezorom.
Aby ste opätovne spustili cyklus zmiesta kde bol
preruený, opätovne stlaète tlaèidlo.
Kontrolka
ZABLOKOVANÉ DVIERKA: signalizuje,
e dvierka spriezorom sú zablokované. Na otvorenie
dvierok je potrebné prerui cyklus (viï Ako vykona
prací cyklus).
Tlaèidlo skontrolkou
ZABLOKOVANIE TLAÈIDIEL:
Aby ste aktivovali alebo zruili zablokovanie
ovládacieho panelu, drte stlaèené tlaèidlo pribline 2
sekundy. Rozsvietená kontrolka signalizuje, e
ovládací panel je zablokovaný. Týmto spôsobom sa
zamedzí náhodným zmenám programov, obzvlá, keï
sú vdomácnosti deti.
Kontrolka EKO: Krozsvieteniu ikony
dôjde
vprípade, ked sa pri zmene parametrov prania
dosiahne energetická úspora najmenej 10%. Okrem
toho, ete pred aktiváciou reimu Stand by, sa ikona
rozsvieti na pár sekúnd; pri vypnutom zariadení je
odhad energetickej úspory pribline 80%.
Tlaèidlo TEPLOTA
Otoèný ovládaè
VO¼BA
PROGRAMOV
Tlaèidlá s kontrolkami
VOLITE¼NÉ FUNKCIE
Kontrolka
ZABLOKOVANÉ
DVIERKA
Tlaèidlo
skontrolkou
TART/PAUSE
Ikony FÁZY
PRANIA
Tlaèidlo ODSTREÏOVANIE
Tlaèidlo
ONESKORENÝ
TART
Tlaèidlo skontrolkou
ZABLOKOVANIE
TLAÈIDIEL
Tlaèidlo skontrolkou
ON/OFF
Kontrolka
EKO
Tlaèidlá s kontrolkami
VOLITELNÉ FUNKCIE
Displej TEPLOTA
Displej ODSTREÏOVANIE
Displej ONESKORENÝ TART/
DOBA TRVANIA CYKLU
SK
18
POZNÁMKA: pri prvom pouití práèky vykonajte prací
cyklus bez prádla, spracím prostriedkom a
nastaveným pracím programom pre vlnu 90 °C, bez
predpierania.
1. ZAPNUTIE ZARIADENIA. Stlaète tlaèidlo
. Vetky
kontrolky sa rozsvietia na 1 sekundu a následne
zostane rozsvietená kontrolka tlaèidla
, a
kontrolka TART/PAUSE bude pomaly blika.
2. NAPLÒTE PRÁÈKU PRÁDLOM. Otvorte dvierka s
priezorom. Naplòte práèku prádlom, prièom dbajte,
aby nedolo kprekroèeniu mnostva náplne,
uvedeného vtabu¾ke programov na nasledujúcej
strane.
3. NAPLNTE DÁVKOVAC PRACÍCH PROSTRIEDKOV.
Vytiahnite dávkovaè pracích prostriedkov a naplnte
prísluné priehradky pracím prostriedkom, spôsobom
vysvetleným vèasti Popis zariadenia.
4. ZATVORTE DVIERKA SPRIEZOROM.
5. ZVOLTE PRACÍ PROGRAM. Otáèajte OTOCNÝM
OVLÁDACOM PROGRAMOV smerom doprava
alebo dolava, a kým nezvolíte poadovaný program;
automaticky budú zvolené teploty, rýchlost
odstredovania a intenzita prania, prièom je moné
ich zmenit.
6. NASTAVTE PRACÍ PROGRAM POD¼A VAICH
POTRIEB. Pouite ktomu prísluné tlaèidlá
ovládacieho panelu:
Zmena teploty a/alebo rýchlosti
odstredovania.
Zariadenie automaticky zobrazuje maximálnu teplotu
a rýchlos odstreïovania pre nastavený program
alebo posledné zvolené hodnoty, ak sú vhodné pre
zvolený program. Stlaèením tlaèidla
je moné
postupne zníi teplotu a po pranie v studenej vode
(
). Stlaèením tlaèidla je moné postupne
zníi rýchlos odstreïovania a po jeho úplné
vylúèenie (
). Ïalie stlaèenie tlaèidiel obnoví
nastavenie maximálnych prednastavených hodnôt.
Výnimka: pri volbe programu BAVLNA bude moné
zvýit teplotu a na 90°C.
Nastavenie oneskoreného tartu.
Postupným stláèaním prísluného tlaèidla je moné
dosiahnu poadovanú dobu oneskorenia. Poèas
nastavovania bude zobrazená doba oneskorenia
spolu sblikajúcim symbolom
.
Po nastavení oneskoreného tartu bude na displeji
rozsvietený symbol
adoba trvania cyklu. Pri
jednom stlaèení tlaèidla bude zobrazená nastavená
doba oneskorenia.
Zruenie oneskoreného tartu sa vykonáva
stláèaním tlaèidla a po zobrazenie nápisu OFF;
dôjde k zhasnutiu symbolu
.
Po stlaèení tlaèidla TART/PAUSE bude moné
zmenit hodnotu oneskorenia tartu len jej zníením.
Zmeòte vlastnosti cyklu.
Stlaèením tlaèidiel VOLITELNÝCH FUNKCIE
môete nastavit prací program podla vaich potrieb.
Stlaète tlaèidlo za úèelom aktivácie volitelnej
funkcie; rozsvieti sa prísluná kontrolka.
Opätovným stlacením môete zvolenú volitelnú
funkciu zruit; dôjde kzhasnutiu príslunej
kontrolky.
Ak zvolená funkcia nie je vhodná prenastavený
program, bude to signalizované blikaním kontrolky
aakustickým signálom (3 pípnutia) afunkcia nebude
aktivovaná.
Vprípade, e zvolená volitelná funkcia nie je
kompatibilná sinou predtým zvolenou funkciou,
kontrolka prvej volitelnej funkcie bude blikat a bude
aktivovaná len druhá, pricom kontrolka zvolenej
funkcie sa rozsvieti stálym svetlom.
7. SPUSTTE PROGRAM. Stlaète tlaèidlo TART/
PAUSE. Prísluná kontrolka sa rozsvieti stálym
svetlom a dvierka spriezorom sa zablokujú
(rozsvietená kontrolka ZABLOKOVANÉ DVIERKA
). Poèas pracieho cyklu sa postupne rozsvietia
prísluné ikony, odpovedajúce jednotlivým fázam
prania, informujúce o jeho priebehu.
Ak chcete zmeni program poèas pracieho cyklu,
prerute èinnos práèky stlaèením tlaèidla TART/
PAUSE; následne zvo¾te poadovaný cyklus a
opätovne stlaète tlaèidlo TART/PAUSE.
Aby bolo moné otvori dvierka poèas pracieho
cyklu, je potrebné stlaèi tlaèidlo TART/PAUSE; ak
je kontrolka ZABLOKOVANÉ DVIERKA
zhasnutá, bude moné dvierka otvorit. Opätovným
stlacením tlacidla TART/PAUSE opätovne uvedte
do èinnosti prací program zbodu, v ktorom bol
preruený.
8. UKONÈENIE PROGRAMU. Je signalizované
rozsvietením nápisu END. Dvierka spriezorom bude
moné okamite otvorit. Ked kontrolka TART/
PAUSE bliká, ukonèite cyklus stlaèením tlaèidla.
Otvorte dvierka, vylote prádlo a vypnite zariadenie.
Ak si prajete zruit u zahájený cyklus, drte
stlaèené tlaèidlo
, a kým nedôjde kprerueniu
cyklu akvypnutiu zariadenia.
Ako vykona prací cyklus
19
SK
Volite¾né funkcie prania
Super Pranie
Vdaka pouitiu väèieho mnostva vody v poèiatoènej fáze
cyklu a vdaka pouitiu dlhej doby, táto volitelná funkcia
zarucuje pranie s vysokou kvalitou.
Môe sa pouíva sbieliacim
prostriedkom alebo bez
neho. Ak si prajete vykona
takéto bielenie, vlote
prídavnú nádobku 3
zprísluenstva do nádobky
1. Pri dávkovaní bieliaceho
prostriedku neprekraèujte
úroveò max vyznaèenú na
stredovom èape(viï
obrázok). Ak si prajete
vykona samostatné bielenie, nalejte bieliaci prostriedok
do prídavnej nádobky 3, nastavte program Extra Plákanie
a aktivujte volite¾nú funkciu Super Pranie .
Nie je moné ju aktivova pri programoch , , , ,
, , , .
¼ahké ehlenie
Vo¾bou tejto volite¾nej funkcie bude pranie a
odstreïovanie náleite zmenené, aby sa predilo tvorbe
záhybov. Po ukonèení cyklu práèka vykoná pomalé
otáèanie bubna sprevádzané blikaním kontroliek ¼ahké
ehlenie a TART/PAUSE. Ukonèenie cyklu sa vykonáva
stlaèením tlaèidla TART/PAUSE alebo tlaèidla ¼ahké
ehlenie.
V programe Hodváb
zariadenie ukonèí cyklus
sprádlom namoèeným vo vode a blikajúcou kontrolkou
¼ahké ehlenie. Za úèelom odèerpania vody a vyloenia
prádla zpráèky je potrebné stlaèi tlaèidlo TART/PAUSE
alebo tlaèidlo ¼ahké ehlenie.
Nie je moné ju aktivova pri programoch
, , , , .
Úspora Èasu
Po zvolení tejto volitelnej funkcie dôjde kskráteniu doby
trvania programu o30-50%, podla zvoleného cyklu, pri
súèasnej úspore vody aenergie. Pouite tento cyklus na
nie príli zneèistené prádlo.
Nie je moné ju aktivova pri programoch
, , , ,
, , , , .
Extra Plákanie
Volbou tejto volitelnej funkcie sa zvýi úèinnost plákania a
zaistí sa maximálny stupen odstránenia pracieho
prostriedku. Je uitoèné hlavne pre pokoky so zvýenou
citlivostou na pracie prostriedky. Odporúca sa pouit túto
funkciu pri plne naloenej práèke alebo pri pouití
vysokých dávok pracieho prostriedku.
Nie je moné ju aktivovat pri programoch
, , .
3
1
2
Programy a volite¾né
funkcie
Tabu¾ka programov
(*) Je moné kontrolova dobu trvania pracích programov na displeji.
Pre vetky Test Institutes:
1) Kontrolný program pod¾a normy EN 60456: nastavte program
steplotou 60°C.
2) Dlhý program na pranie bavlny: nastavte program
steplotou 40°C.
3) Krátky program na pranie bavlny: nastavte program
steplotou 40°C.
Ikona Popis programu
Max.
teplota
(°C)
Max.
rýchlost
(otáèky za
minútu)
Pracie prostriedky a prídavné
prostriedky
Max.
náplò
(kg)
Doba
trvania
cyklu
Prací
prostriedok
Aviváz
Bieliaci
prostriedok
Programy na pranie bavlny
Bavlna
s predpieraním
(Pridajte prací prostriedok do príslunej priehradky).
90° 1000
ll
- 6
Bavlna (1)
: Znaène pinavé biele afarebné prádlo zodolných tkanín.
60°
(Max. 90°)
1000
lll
6
Bavlna (2)
: Znaène pinavé biele afarebné prádlo zchúlostivých tkanín.
40° 1000
lll
6
Farebná
Bavlna (3)
40° 1000
lll
6
Koele
40° 600
lll
2
Dzínsy
40° 800
ll
- 2,5
peciálne programy
Baby:
Ve¾mi pinavé farebné chúlostivé prádlo.
40° 800
lll
2
Synteticka
odolné tkaniny
60° 800
lll
2,5
Synteticka
chúlostivé tkaniny
40° 800
lll
2,5
Bed&Bath:
Pre poste¾né a kúpe¾òové prádlo.
60° 1000
lll
6
Povleèenie:
Pre prádlo plnené husím perím.
30° 1000
ll
- 1
Hodváb:
Pre prádlo zhodvábu, viskózy, spodné prádlo.
30° 0
ll
- 1
Vlna:
Pre vlnu, kamír, atd'.
40° 600
ll
- 1
Mix. 30':
Na rýchle ozivenie ¾ahko zneèisteného prádla (neodporúèa sa
pre vlnu, hodváb a prádlo urèené na pranie v rukách).
30° 800
ll
- 3
Dielèie programy
Extra Plákanie
- 1000 -
ll
6
Odstreïovanie
- 1000 - - - 6
Vypútanie
- 0 - - - 6
(*) Poznámka: Pribline po 10 minútach od TART zariadenie na základe naplnenia prepoèíta azobrazí dobu zostávajúcu do ukonèenia programu.
SK
20
Pracie prostriedky a prádlo
Prací prostriedok
Vo¾ba druhu a mnostva pracieho prostriedku závisí od
druhu tkaniny (bavlna, vlna, hodváb), od farby, od
teploty prania, od stupòa zneèistenia a od tvrdosti
vody.
Správne dávkovanie pracieho prostriedku zabranuje
plytvaniu a etrí ivotné prostredie: aj ked sa jedná o
biodegradabilné látky, pracie prostriedky naruujú
prirodzenú rovnováhu vprírode.
Odporúèa sa:
pouíva prákové pracie prostriedky pre prádlo
zbielej bavlny a na predpieranie.
pouíva tekuté pracie prostriedky pre chúlostivé
bavlnené prádlo a pre vetky programy pri nízkej
teplote.
pouíva tekuté pracie prostriedky pre chúlostivé
tkaniny na pranie vlny a hodvábu.
Prací prostriedok musí by naliaty pred zahájením
prania do príslunej priehradky alebo do dávkovaèa,
ktorý sa vkladá priamo do bubna. Vtomto prípade nie
je moné zvoli cyklus Bavlna s predpieraním.
Nepouívajte pracie prostriedky urèené na pranie v
rukách, pretoe spôsobujú tvorbu nadmerného
mnostva peny.
Príprava prádla
Pred naloením prádlo riadne rozprestrite.
Rozde¾te prádlo pod¾a druhu tkaniny (symbol na
visaèke prádla) a farby, prièom dbajte na oddelenie
farebného prádla od bieleho;
Vyprázdnite vrecká a skontrolujte gombíky;
Neprekraèujte hodnoty povolenej náplne uvedenej v
Tabu¾ka programov, vzahujúce sa na hmotnos
suchého prádla:
Ko¾ko vái prádlo?
1 prestieradlo 400-500 g
1 oblieèka 150-200 g
1 obrus 400-500 g
1 upan 900-1200 g
1 uterák 150-250 g
1 dínsy 400-500 g
1 koela 150-200 g
Rady pre pranie
Koele: Pouite prísluný program Koele na
pranie koiel zrôznych druhov látok afarby aby ste
zabezpeèili maximálnu starostlivost o ne.
Dínsy: Pouite prísluný program Dínsy
pre
vetky kusy prádla zlátky Denim; pred praním
jednotlivé kusy prádla obráte naruby apouite tekutý
prací prostriedok.
Baby: Pouite prísluný program Baby
na
odstránenie typicky zneèisteného detského obleèenia
adostatoène odstránte prací prostriedok zprádla, aby
ste predili alergickým reakciám jemnej pleti detí.
Tento prací cyklus bol navrhnutý na zníenie mnostva
baktérií spouitím vyieho mnostva vody, èím sa
optimalizuje úèinok pecifických hygienizaèných
prísad, pridaných kpraciemu prostriedku.
Na konci prania zariadenie vykoná pomalé otáèania
bubna pre zabránenie tvorbe záhybov; cyklus je moné
ukonèi stlaèením tlaèidla TART/PAUSE.
Hodváb: Pouite prísluný program Hodváb
na
pranie vetkého prádla z hodvábu. Odporúèa sa
pouitie pracieho prostriedku pre chúlostivé prádlo.
Záclony: Pouite program Hodváb
. Prehnite ich
aulote do oblieèky na vankú alebo do sáèku zo
sieoviny.
Vlna: je jediná práèka, ktorá získala prestíne uznanie
Woolmark Platinum Care (M.0508) od The Woolmark
Company, ktoré certifikuje pranie vtejto práèke
vetkých druhov prádla zvlny, a to i prádla svisaèkou
pra výhradne v rukách
. Spouitím programu vlna
je preto moné úplne bez obáv pra vetko prádlo
zvlny so zárukou vysokej kvality.
Povleèenie: Pri praní prádla plneného husím perím
(nepresahujúce hmotnost 1 kg), hlavnice, vetrovky,
pouívajte prísluný program Povleèenie
.
Poste¾né akúpe¾òové prádlo: Táto práèka
umoòuje pra prádlo celej domácnosti vjedinom cykle
Bed&Bath
, ktorý optimalizuje pouitie aviváe a
umoòuje uspori èas a energiu. Odporúèa sa pouitie
prákového pracieho prostriedku.
Odolné kvrny: Odolné kvrny je vhodné pred praním
potrie pevným mydlom a poui program Bavlna
spredpierkou.
Systém automatického vyváenia náplne
Pred kadým odstreïovaním bubon vykoná otáèanie
rýchlosou o málo prevyujúcou rýchlos prania, aby sa
tak odstránili vibrácie aaby sa náplò rovnomerne
rozloila. Vprípade, e po nieko¾ko násobných
pokusoch o vyváenie prádlo ete nebude správne
vyváené, zariadenie vykoná odstreïovanie niou
rýchlosou, ako je prednastavená rýchlos. Ak je práèka
nadmerne nevyváená, vykoná namiesto odstreïovania
vyváenie. Za úèelom dosiahnutia rovnomernejieho
rozloenia náplne a jej správneho vyváenia, odporúèa
sa pomiea ve¾ké a malé kusy prádla.
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
Stránka sa načítava...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
Whirlpool AQSF 09 U (EU) Užívateľská príručka
- Kategória
- Práčky
- Typ
- Užívateľská príručka
v iných jazykoch
- English: Whirlpool AQSF 09 U (EU) User guide